reset low washer fluid level impala

You search PDF repair manual about reset low washer fluid level impala, if there are search results will appear below. If search results do not exist, please search by others keyword.



  reset low washer fluid level impala Direct Download speed 5432 Kb/s

  reset low washer fluid level impala Full Version speed 8172 Kb/s



Low Engine Coolant Level Indicator Always On (Diagnose Low Coolant Level System Operation/Check Sensor for Oil Contamination)

0

Filed Under (More Manuals) by admin on 19-05-2012

download
2000-2002 Buick Century, Regal 2000-2001 Chevrolet Lumina 2000-2002 Chevrolet Impala, Monte Carlo 2000-2002 Pontiac Grand Prix 2000-2002 Oldsmobile Intrigue 1. Verify that the coolant is at proper level in the radiator and the coolant recovery bottle. If the coolant is low, add proper amount of 50/50 water and DEX-COOL® mixture. If the low coolant light operates properly, diagnose the cooling system for loss of coolant as outlined in SI. DO NOT proceed further with this bulletin. 2. Remove the low coolant level sensor. Refer to Coolant Level Module Replacement in the Engine Cooling sub-section. 3. With the key on, the engine off and the coolant level sensor disconnected from the vehicle wiring harness, observe the low coolant light: Subject: Low Engine Coolant Level Indicator Always On (Diagnose Low Coolant Level System Operation/Check Sensor for Oil Contamination) Models: 2000-2002 Buick Century, Regal 2000-2001 Chevrolet Lumina 2000-2002 Chevrolet Impala, Monte Carlo 2000-2002 Pontiac Grand Prix 2000-2002 Oldsmobile Intrigue • Light is on — Chassis wiring or instrument cluster concern. Follow the appropriate diagnostic information in SI. • 4. With the key off, connect the coolant level sensor into the vehicle’s wiring harness. Connect a ground wire (1) to the battery negative terminal. Using a sharp probe (3) attached to the ground wire, ground the coolant sensor probe (2) as shown in the illustration. Make sure a good contact is made. With the key on and the engine off, observe the low coolant light for at least 15 seconds. 5. Using a small wire brush or emery cloth, polish the low coolant level sensor probe to remove any film or oxidation. The probe should be a bright brass color when finished. Use Brake Parts Cleaner to flush removed deposits from the low coolant sensor probe. Reinstall the low coolant sensor into the vehicle and proceed to Step 6. 6. Flush the cooling system and install new DEX-COOL® mixture as outlined in the SI. Check the vehicle’s warranty history to determine if any engine gasket had recently been changed. If there has not been a recent gasket replacement, locate and repair the source of the engine oil contamination

Related Content:

low coolant 01 suburban, Low coolant light olds intrigue, how to check radiator fluid level pontiac grand prix, replace low coolent sencor on 1997 chevy lumnia, 2002 Chevrolet Impala see a diagram of the a/c controls, p0446 2002 monte carlo, 99 buick park avenue radiator installation, 2002 mercury sable cooling system, Low Coolant Sensor Location in olsdmobile silluette, evap sensor on 2002 suburban

4L60-E Automatic Transmission/Torque Converter Clutch (TCC) Shudder, Water in Transmission (Repair Transmission and Replace Transmission Filler Tube, Level Indicator and Seal)4L60-E Automatic Transmission/Torque Converter Clutch (TCC) Shudder, Water in Transmission (Repair Transmission and Replace Transmission Filler Tube, Level Indicator and Seal) Transmission Repair

0

Filed Under (More Manuals) by admin on 08-01-2012

download
Transmission Repair 1. Remove the transmission. Refer to the appropriate SI procedure. 2. Disassemble and inspect the transmission. Refer to Unit Repair Automatic Transmission – 4L60-E/4L65-E. Important: Subject: 4L60-E Automatic Transmission/Torque Converter Clutch (TCC) Shudder, Water in Transmission (Repair Transmission and Replace Transmission Filler Tube, Level Indicator and Seal) Models: 2004-2005 Buick Rainier 2003-2005 Chevrolet TrailBlazer Models 2003-2005 GMC Envoy Models 2003-2004 Oldsmobile Bravada 2005 Saab 9-7X with 4.2L In-Line 6 Cylinder Engine (VIN S — RPO LL8) • Visible rust on the transmission fluid level indicator. • Visible water in the oil pan. • A milky white substance inside the pan area. • Spacer plate gaskets that appear to be glued to the spacer plate, valve body or case. • Rust on internal transmission iron/steel components. • Remove the surge tank cap and examine the coolant for signs of contamination with transmission fluid (the coolant will have a milky, not clear appearance). • If the coolant has a normal, clear appearance, the radiator should not be replaced. • The cooler can also be tested by following the Coolant System Leak Test procedure (SI Document ID# 877442). Do NOT replace a radiator without verifying that the transmission oil cooler is leaking. If water or coolant is found in the transmission, the following components MUST be replaced. Replace the Transmission Fluid Filler Tube, Seal and Fluid Level Indicator WITH the transmission REMOVED from vehicle. 1. Remove the transmission fluid filler tube from the transmission. 2. Replace the transmission fill tube seal, P/N 1259475. 3. Replace the transmission fill tube, P/N 15000220, following the appropriate SI Document for Transmission Installation. 4. Replace the transmission fluid level indicator, P/N 15069769 when appropriate during the transmission installation. Replace the Transmission Fluid Filler Tube, Seal and Fluid Level Indicator with the transmission in the vehicle. 1. Remove the air cleaner outlet duct. Refer to Air Cleaner Element Replacement (SI Document ID# 1364496). 2. Remove the transmission fluid level indicator from the filler tube. 3. Remove the filler tube nut (2) located on the right side of the engine. 4. Remove the filler tube from the vehicle. Tip It is necessary to remove the two A/C line (suction line / low side of muffler hose) retainers and reposition • Replace all of the rubber type seals. • Replace all of the composition-faced clutch plate assemblies including the band. • Replace all of the nylon parts (Thrust Washers). • Replace the torque converter. • Thoroughly clean and rebuild the transmission, using new gaskets and oil filter. • Flush and flow check the transmission oil cooler using J 45096. Refer to Corporate Bulletin Number 02-07-30- 052C or newer – Automatic Transmission Oil Cooler Flush and Flow Test Essential Tool J 45096 TransFlow .
the A/C line to allow proper clearance for installation of the new transmission fluid fill tube. 5. Remove the A/C line at the oil level indicator tube bracket nut. 6. Remove the A/C bracket bolt from the engine lift hook. 7. Reposition the A/C line upward. 8. Install the new transmission filler tube, P/N 15000220, into position but NOT into the transmission at this time. 9. Raise the vehicle. Refer to Lifting and Jacking the Vehicle in General Information (SI Document ID# 744862). 10. Remove the two bolts securing the transmission heat shield to the transmission. 11. Remove the transmission heat shield from the transmission. 12. Remove the old filler tube seal from the transmission case. 13. Install a new seal, P/N 1259475 into the transmission case. 14. Position the new transmission filler tube into the transmission seal. 15. Install the transmission heat shield to the transmission. 16. Install the two bolts securing the transmission heat shield to the transmission. Tighten Tighten the bolts to 17 N·m (13 lb ft). 17. Lower the vehicle. 18. Install the nut securing the filler tube to the stud. Tighten Tighten the nut to 10 N·m (89 lb in). 19. Reposition the A/C line into place. 20. Install the A/C line bracket to the oil level indicator tube stud and secure the bracket with the nut. 21. Install the A/C line bracket to the engine lift bracket and secure the A/C bracket with the bolt

Related Content:

yhs-lavasoft, gm 4l60e band adjustment screws, how to check tranmission fluid on 2012 kia sedona, 2003 trailblazer torque converter removal, 2011 crv engine whine, 2005 explorer transmission exploded view, automatic transmission adjustments for 1997 yuko, 1997 e450 power stroke trans mount parking brake, transmission module for 1999 ford ranger xlt, manual pdf transmicion automatica ram 2001

AUTOMATIC TRANSMISSION Checking Transmission Fluid Level and Condition

0

Filed Under (Honda Manuals) by admin on 25-05-2011

download
Checking fluid level and condition (color and odor) at regular intervals will provide early diagnosis information about the transmission. This information may be used to correct a condition that, if not detected early, could result
in major transmission repairs. IMPORTANT: When new, automatic transmission fluid is red in color. As the vehicle is driven, the transmission fluid will begin to look darker in color. The color may eventually appear light brown. A dark brown color with burnt odor may indicate excessive fluid deterioration and signal a need for fluid change. Fluid Level When adding or changing fluid, use only DEXRON ®-lll. Refer to Maintenance and Lubrication in General
Information section for maintenance information and servicing interval. CAUTION: DO NOT OVERFILL. Overfilling will cause foaming, loss of fluid, abnor- mal shifting and possible damage to the transmis-sion. 1. Park the vehicle on level ground and apply the parking brake firmly. 2. Check fluid level with engine running at idle. NOTE: Be sure that transmission fluid temperature is below 30°C (86°F). 3. Move the selector lever through all gear ranges. 4. Move the selector lever to “Park”. 5. Let engine idle for 3 minutes and open the overfill screw (1). 6. Add released ransmission fluid until it flows out over the overfill screw opening. 7. Let engine idle until a fluid temperature etween 32° C (90°F) and 57°C (135°F) is reached, then close the overfill screw (1). Torque: 38 N*m (28 Ib ft) NOTE: Check transmission fluid temperature with scan tool.

2005-2008 Honda Odyssey Power Steering Pump Whines , Buzzes, or Hums Repair Manual

0

Filed Under (Honda Manuals) by admin on 16-05-2012

download
Inspect the power steering reservoir. Does one of the 3 ribs on the reservoir cover point toward the reservoir holder? Yes – This vehicle already has the revised power steering reservoir. Continue with normal troubleshooting procedures. No – Go to REPAIR PROCEDURE. REPAIR PROCEDURE 1. Drain the power steering reservoir: •Remove the reservoir from its holder. •Raise the reservoir, and disconnect its return hose. •Drain the reservoir fluid into a suitable container. Take care not to spill any fluid on the body or other parts. Wipe off any spilled fluid immediately. 2. Drain the fluid from the power steering system: •Connect a suitable diameter drain hose to the disconnected return hose. •Hold the end of the drain hose in a suitable container. •Start the engine, and run it at idle while you turn the steering wheel lock-to-lock several times. •When the fluid stops running out of the hose, shut off the engine. •Discard the used fluid. 3. Reinstall the return hose to the reservoir, then reattach the reservoir to its holder. Fill the reservoir to its upper level line with new power steering fluid. 4. Bleed the air from the power steering system: •Start the engine. •With the engine at a fast idle, turn the steering wheel lock-to-lock several times. 5. Check the condition of the fluid in the reservoir: •If the fluid looks contaminated, dark, or discolored, repeat steps 1 thru 5. •If the fluid is clear, go to step 6. 6. Place a suitable container under the vehicle to catch any fluid 7. Replace the power steering fluid reservoir: •Remove the reservoir from its holder. •Disconnect the return hose from the reservoir, and pour the fluid from the reservoir into a container. •Disconnect the outlet hose from the reservoir, and remove the reservoir. •Install a new reservoir in the reverse order of removal. •Fill the reservoir to its upper level line with new power steering fluid. 8. Start the engine, and run it at a fast idle. Turn the steering from lock-to-lock several times to bleed any air from the system. 9. Recheck the fluid level in the reservoir, and add more if needed. Do not fill the reservoir beyond its upper level line.

Related Content:

2011 cruze recall leaking radiator fluid, toyota dyna clutch fluid reservoir, washer fluid low silverado trucks

VEHICLE WITH ALL 4 WHEELS ON THE GROUND, EXPANDED GUIDELINES TO PREVENT TRANSMISSION DAMAGE SERVICE PROCEDURE

0

Filed Under (Ford Manuals) by admin on 04-01-2012

download
FORD: MERCURY: 2010 Fusion 2010 Milan 2009-2010 Escape 2009-2010 Mariner SERVICE PROCEDURE 3. Do not flat tow the vehicle for greater than 6 hours at a time. There are specific instructions listed in the Owner Guide that must be followed to recreational tow/flat 4. Start and run the engine for: tow/tow a vehicle with all 4 tires on the ground. a. 5 minutes before towing each day Advise customers of the following expanded recreational towing guidelines. b. 5 minutes every 6 hours or less. 1. Transmission fluid level must be checked at c. While running the engine at idle for 5 operating temperature of 185 °F – 200 °F (85 minutes, with foot on the brake, shift °C – 93 °C), per Workshop Manual (WSM), through all gears. Section 307-01. At this temperature, adjust fluid These guidelines are designed to prevent damage level between minimum line and the minimum to the transmission due to overheating. hole at the bottom of the hash marks on dipstick. This level is within the safe operating If setting the fluid level for a customer that will be fluid level and does not require the customer to recreational (flat) towing the vehicle, set the level have the fluid level readjusted after flat tow between minimum line and the minimum hole at the operation. (Figure 1) bottom of the hash marks on dipstick (Figure 1) per WSM Section 307-01

Related Content:

2010 ranger srvice manual, ford service manual f-150 2010, 2010 ford fusion anttifreeze replacement, ford escape 2010 service manual

Toyota Land Cruiser/ Lexus LX 470 Big Brake Kit Installation Instructions

0

Filed Under (Toyota Manuals) by admin on 26-09-2011

download
Disconnect Stock Brake Line Disconnect Stock Brake Line Disconnect Stock Brake Line Disconnect Stock Brake Line Disconnect Stock Brake Note: All Photographs in This Manual Show Left Side Note: All Photographs in This Manual Show Left Side Note: All Photographs in This Manual Show Left Side Note: All Photographs in This Manual Show Left Side Note: All Photographs in This Manual Show Left Side Installation Unless Noted Otherwise. Installation Unless Noted Otherwise. Installation Unless Noted Otherwise. Installation Unless Noted Otherwise. Installation Unless Noted Otherwise. After securing the vehicle at a convenient height, remove the front wheels. WARNING – Brake fluid will damage most painted surfaces. Immediately clean spilled WARNING – Brake fluid will damage most painted surfaces. Immediately clean spilled WARNING – Brake fluid will damage most painted surfaces. Immediately clean spilled WARNING – Brake fluid will damage most painted surfaces. Immediately clean spilled WARNING – Brake fluid will damage most painted surfaces. Immediately clean spilled br br br br brake fluid fr ake fluid fr ake fluid fr ake fluid fr ake fluid from any painted sur om any painted sur om any painted sur om any painted sur om any painted surfaces. faces. faces. faces. faces. Place a drip tray or several rags directly below the inboard brake line connection. If the area around the brake line connection to the chassis and strut is dirty, clean with brake cleaner or appropriate cleaning agent. Note- Be sure the cap is securely installed on the master cylinder. If the cap is loose or Note- Be sure the cap is securely installed on the master cylinder. If the cap is loose or Note- Be sure the cap is securely installed on the master cylinder. If the cap is loose or Note- Be sure the cap is securely installed on the master cylinder. If the cap is loose or Note- Be sure the cap is securely installed on the master cylinder. If the cap is loose or removed, it is likely more fluid will drip. removed, it is likely more fluid will drip. removed, it is likely more fluid will drip. removed, it is likely more fluid will drip. removed, it is likely more fluid will drip. Note: If you remove the bottom lug nut last while holding the bottom of the tire, it will lessen the chances of thewheel tilting on it’s own and make removal easier. Step 2 Step 2 Step 2 Step 2 Step 2 Step 1 Step 1 Step 1 Step 1

Related Content:

2014 tundra factory painted bumper

2008 Ford Taurus AWD V6-3.5L – Rear Brake Pads Removal And Installation Manual

0

Filed Under (Ford Manuals) by admin on 25-06-2012

download
Removal WARNING: Do not use any fluid other than clean brake fluid meeting manufacturer’s specification. Additionally, do not use brake fluid that has been previously drained. Following these instructions will help prevent system contamination, brake component damage and the risk of serious personal injury. WARNING: Carefully read cautionary information on product label. For EMERGENCY MEDICAL INFORMATION seek medical advice. In the USA or Canada on Ford/Motorcraft products call: 1-800-959-3673. For additional information, consult the product Material Safety Data Sheet (MSDS) if available. Failure to follow these instructions may result in serious personal injury. CAUTION: Brake fluid is harmful to painted and plastic surfaces. If brake fluid is spilled onto a painted or plastic surface, immediately wash it with water. CAUTION: Do not allow the brake fluid to come in contact with the adhesive backing on the brake pads. If brake fluid is spilled onto the brake pads, new pads must be installed. CAUTION: Use only specified brake parts cleaner. Use of other cleaners may leave a residue on the brake caliper preventing the brake pads adhesive surface from bonding with the brake caliper. 1. Remove the wheel and tire. 2. Check the brake fluid level in the brake fluid reservoir. * If required, remove fluid until the brake master cylinder reservoir is half full. 3. Remove the brake caliper bolts. 4. CAUTION: Do not use the brake caliper sight hole to retract the pistons as this may damage the pistons and boots. CAUTION: Do not allow the caliper to hang from the brake hose or damage to the hose may occur. CAUTION: Care must be taken when servicing rear brake components without disconnecting the parking brake cable from the brake caliper lever. Carefully position the caliper aside using a suitable support or damage to the parking brake cable end fittings may occur. Using hand force and a rocking motion, separate the brake caliper from the anchor plate. Position the brake caliper aside. * Support the caliper with mechanic’s wire. 5. CAUTION: When the brake pads are separated from the brake caliper , new brake pads must be installed to prevent brake noise. The brake pads are one-time use only. Remove and discard the brake pads and spring clips from the brake caliper anchor plate. 6. NOTE: Do not remove the anchor plate guide pins. The guide pins are press fit to the brake caliper anchor plate. If the guide pins are damaged a new anchor plate must be installed. Inspect the brake caliper anchor plate assembly. * Check the guide pins and boots for binding or damage. * Install a new brake caliper anchor plate if it is worn or damaged. Installation 1. NOTE: To move the piston back into the caliper, the LH piston is turned clockwise and the RH piston is turned counterclockwise. NOTE: A moderate to heavy force toward the caliper piston must be applied. If sufficient force is not applied, the internal park brake mechanism clutch cone will not engage and the piston will not compress. Using the special tool (or equivalent such as OTC tool 7317A), compress the brake caliper piston into its cylinder. 2. Clean the residual adhesive from the brake caliper fingers and pistons using the specified brake parts cleaner. 3. CAUTION: Do not allow grease, oil, brake fluid or other contaminants to contact the brake pad or caliper mating surface or damage to components may occur. Do not install contaminated pads. NOTE: Install all the new hardware supplied with brake pad kit. Install the new spring clips and brake pads. 4. Position the brake caliper and install the 2 bolts. * Tighten to 29 Nm (21 lb-ft). 5. If necessary, fill the brake fluid reservoir with clean, specified brake fluid. 6. With the vehicle engine running, apply 89-133 N (20-30 lb) of pressure on the brakes for approximately one minute, to make sure the brake pads adhere to the caliper before any contamination can be introduced. 7. Test the brakes for normal operation.

Related Content:

diagram of a 2004 chev thoe break line sysetm, hummer h3 brake job, isuzu npr brake adjustment, rear disk brake assembly on 2000 Saturn, isuzu npr brake booster removal instruction, 2002 ford ranger brake bleeding procedure, front brake line diagram on 2004 tahoe, how bleed bakes on 1998 chevy malibu, replace avalon caliper piston boot, repair manual for toyota yaris brakes

2002 Isuzu Truck Axiom Vehicle Level Transmission and Drivetrain Automatic Transmission/ Transaxle Fluid – A/ T Service and Repair

0

Filed Under (Isuzu Manuals) by admin on 09-01-2012

download
Changing Transmission Fluid There is no need to change the transmission fluid unless the transmission is used under one or more of the following heavy duty conditions. A. Repeated short trips B. Driving on rough roads C. Driving on dusty roads D. Towing a trailer If the vehicle is used under these conditions, change the fluid every 20,000 miles (32,000 km). 1. Place a large drain pan under the oil pan. 2. Remove the transmission oil drain screw (2) and drain fluid. 3. Tighten drain screw (2). Torque: 38 Nm (28 ft. lbs.) 4. Remove the transmission overfill screw (1) and fill transmission through overfill screw opening, using DEXRON-III ATF. Note: Add transmission fluid until it flows out over the overfill screw opening. 5. Let engine idle until a fluid temperature between 32°C (90°F) and 57°C (135°F) is reached. 6. Add transmission fluid until it flows out over the overfill screw opening, then close the overfill screw (1). Torque: 38 Nm (28 ft. lbs.) Note: To prevent fluid leaks, the overfill screw and oil drain screws gasket must be replaced each time these screws are removed. Note: Check transmission fluid temperature with scan tool

Related Content:

1999 ISUZU RODEO HOW TO REPLACE TORQUE CONVERTER

2008 Ford F-Super Duty LACKS POWER, LEAKS FLUID FROM EXHAUST PIPE, ABNORMAL TAILPIPE SEDIMENT, WHITE SMOKE, EXHAUST SMELL, AND MIL ON SERVICE PROCEDURE

0

Filed Under (Ford Manuals) by admin on 02-02-2012

download
ACTION To diagnose and correct the concern, refer to the following Service Procedure. SERVICE PROCEDURE NOTE DO NOT START ENGINE Evaluation, Inspections, And Checks 1. Retrieve KOEO diagnostic trouble codes (DTCs). 2. Check oil level. Remove and clean dipstick. Reinsert into dipstick tube only until dipstick handle reaches top of dipstick tube (Figure 1). NOTE FIGURE 1 DEMONSTRATES DIPSTICK Figure 1 – Article 07-8-9 POSITIONING FOR OVER-FULL CHECK. KEEP 3. Check coolant level. DIPSTICK HANDLE OFFSET OF CENTER TO PREVENT IT FROM FULLY SEATING. IF OIL 4. Check fuel quality. LEVEL IS BELOW THE MAX MARK, OIL IS NOT OVER-FULL. 5. Inspect tailpipes for abnormal sediment; for example black soot, white ash, oil, coolant, or fuel. 6. Inspect vehicle for coolant, oil and fuel leaks at the following locations: •Tailpipes Repair Directions •Section A – If the following DTCs are present P0087, P2291, P0263-0284, P0300-P0308, or P1336 or if observation of external fuel leaks, for example, wetness around exhaust manifolds or over-full oil level indication. •Section B – If the following DTCs are present P132B, P2262, or P2263 or observation of oil leaks (aside from over-full oil level) or oil level is low. Figure 2 – Article 07-8-9 •Section C – If coolant low or observation of 8. Replace any leaking components and verify coolant leaks. leak has been repaired while running IDS high •Sections A, B, and C – If only abnormal sediment pressure fuel system test – KOER. in tailpipes. 9. Perform WSM, Section 303-04D – Turbocharger SECTION – A Bearing Clearance Check. Fuel System Diagnostics 10. If fuel quality is poor, drain all fuel and replace with known good ultra-low sulfur diesel fuel. NOTE IN CASES WHERE ENGINE OIL HAS BEEN 11. If no DTCs were stored in pending or DILUTED WITH DIESEL FUEL AND ALL REPAIRS continuous memory go to Step 13. ARE COMPLETE, RELEASE THE OIL FILTER CAP 12. Is there abnormal sediment in tailpipes or fuel ALLOWING OIL TO DRAIN TO OIL PAN AND evident? KEEP FILTER, DRAIN THE OIL FROM OIL PAN AND FILL WITH NEW OIL. TIGHTEN OIL FILTER a. No – Complete PC/ED worksheet and CAP AND RUN ENGINE FOR 10 MINUTES. applicable PPT tests for the codes retrieved. FINALLY, CHANGE OIL FILTER AND OIL AGAIN. b. Yes – Go to Step 13. 1. If oil is not over-full – go to Step 9. 13. Is there abnormal sediment in the tailpipes?

Related Content:

ford 2014 c max service manual

1999 Mercury Sable A/ T – Cooler Flushing Service Manual

0

Filed Under (Mercury Manuals) by admin on 31-01-2012

download
SERVICE PROCEDURE Prior methods of cooler flushing have not obtained the level of cooler cleaning and contaminant removal that is required to prevent repeat repairs. The “Turbo-Tank Heated Cooler Line Flusher” uses heated Automatic Transmission Fluid ( ATF ) and a pulsating action to loosen system contamination. Previous equipment used solvents to clean & flush coolers, lines and torque- converters. There are 2 issues with this method: Aerosol Solvents should never be used for several reasons. NOTE YOU MUST IDENTIFY THE RETURN COOLER LINE TO START THE BACK FLUSHING PROCEDURE. A quick way to identify the return cooler line (fluid coming out of the cooler and returning to the transmission) is to locate the return cooler line fitting on the transmission case . Refer to the following lists: Rear Wheel Drive ^Residual solvent contamination can cause damage to friction bonding materials within the transmission (Clutches and Bands). ^Lack of fluid heating and agitation prevents this method from completely removing contamination from lines, in-radiator coolers and auxiliary coolers Front Wheel Drive NOTE IF AN IN-LINE FILTER HAS BEEN INSTALLED IN THE COOLER LINE, IT MUST BE REMOVED BEFORE FLUSHING THE COOLER OR COOLER LINES. Purge the cooler and cooler line before flushing: Located on the “Turbo-Tank Heated Cooler Line Flusher” is a fluid transfer and purge valve. This valve can be used to purge the cooler and cooler lines of contaminated fluid before starting the back flush procedure of the fluid cooling system (refer to step 5a of this Service Procedure or Equipment instructions, supplied with the “Turbo-Tank Heated Cooler Line Flusher”). Flush Procedure -The TOP transmission case filling receives the return line. ^CD4E – The REAR or Pump End transaxle case fitting receives the return line. ^4F27E – The REAR or Cover End transaxle case fitting receives the return line. ^AXOD, AXODE, AX4S, AX4N, 4F50N – The BOTTOM transaxle cooler line fitting receives the return line. 1. Check and top off fluid level of the “Turbo-Tank Heated Cooler Line Flusher” tank with transmission fluid. 2. Allow the fluid in the flusher 15-30 minutes to heat up to 140°F (60°C) before using. 3. Install line adapters into the transmission cooler lines. 4. Attach the flusher’s blue line to the transmission return cooler line quick disconnect. 5. Attach the flusher’s red line to the transmission outlet cooler line quick disconnect. a. Follow equipment instructions, to purge cooler lines and cooler prior to starting flushing procedure (using factory installed purge valve and clear hose on “Turbo-Tank Heated Cooler Line Flusher”). 6. Allow the cooling system to back-flush for 10-15 minutes, then flush the cooler in a forward/normal flow direction for an additional 10-15 minutes.

Related Content:

c6 trans cooling line diagram, buick transmission cooler flush

Related Content:

low coolant 01 suburban, Low coolant light olds intrigue, how to check radiator fluid level pontiac grand prix, replace low coolent sencor on 1997 chevy lumnia, 2002 Chevrolet Impala see a diagram of the a/c controls, p0446 2002 monte carlo, 99 buick park avenue radiator installation, 2002 mercury sable cooling system, Low Coolant Sensor Location in olsdmobile silluette, evap sensor on 2002 suburban