resetting anti theft in a chevy tahoe

You search PDF repair manual about resetting anti theft in a chevy tahoe, if there are search results will appear below. If search results do not exist, please search by others keyword.



  resetting anti theft in a chevy tahoe Direct Download speed 5432 Kb/s

  resetting anti theft in a chevy tahoe Full Version speed 8172 Kb/s



1998 Chevrolet Chevy K Pickup DTC P1626 Theft Deterrent Fuel Enable Signal Not Received Repair Manual

0

Filed Under (Chevrolet Manuals) by admin on 24-06-2012

download
An intermittent may be caused by any of the following conditions: Thoroughly check any circuitry that is suspected of causing the intermittent complaint. Refer to Intermittents and Poor Connections Diagnosis in Wiring Systems. If a repair is necessary, refer to Wiring Repairs or Connector Repairs in Wiring Systems. Test Description The number(s) below refer to the step number(s) on the diagnostic table. 2. This test checks if communication can be established between the scan tool and the VTD. If the scan tool cannot communicate with the VTD, refer to Diagnostic System Check – Theft Deterrent in Theft Deterrent. 3. This test checks for any opens in the serial data circuit between the VCM and the VTD. This also checks for any intermittent malfunctions associated with the serial data circuit. 4. This step is to determine if the condition that set the DTC is still present. The engine must be cranked in order to set this DTC. If the condition is present, the engine will start and then stall, indicating the VCM is disabling fuel. 7. Use a scan tool to clear and check for any DTCs in all the modules connected to the Class 2 Serial Data circuit (VCM, VTD, ATC, and BCM). the module itself. After repairing the cause of DTC P1626, clear all DTCs from the systems capable of storing this DTC and DTC U1192. 1 Important: Before clearing the DTCs, use the scan tool Capture Info to save the Freeze Frame and Failure Records for reference. The control module’s data is deleted once the Clear Info function is used. Did you perform the Powertrain On-Board Diagnostic (OBD) System Check? — Go to Step 2 Go to Powertrain On Board Diagnostic (OBD) System Check 2 1. Install the scan tool. 2. Turn ON the ignition leaving the engine OFF. 3. Attempt to establish communications with the VTD (Passlock) Control Module. Does the scan tool communicate with the VTD (Passlock) Control Module? — Go to Step 3 Go to Diagnostic System Check – Theft Deterrent in Theft Deterrent 3 Check the Class 2 Serial Data circuit for the following intermittent conditions: Did you find a problem? • An open in the Class 2 Serial Data circuit between the VCM and the VTD (Passlock) Control Module. • A short to ground. • A short to voltage. • Loose or damaged terminals at the DLC, VCM or the VTD (Passlock) Control Module. — Go to Step 6 Go to Step 4 4 1. Turn OFF the ignition. 2. Connect or install any connectors or components that were disconnected or removed. 3. Clear all DTCs using a scan tool. 4. Turn OFF the ignition for 15 seconds. 5. Attempt to start the engine. Does DTC P1626 reset? — Go to Diagnostic System Check – Theft Deterrent in Theft Deterrent Go to Step 5 5 This DTC is intermittent. Are any additional DTCs stored? — Go to the applicable DTC table Go to Diagnostic Aids 6 Repair the circuit as necessary. Refer to Wiring Repairs or Connector Repairs in Wiring Systems. Is the action complete?

Related Content:

p1626 chevy venture, 87 bonco 2 parking brake control assembly diagram, what is a class 2 malfunction, VTD? chevrolet, universal theft deterrent system for 1996 bonneville, theft deterrent module location 99 olds intrigue, hummer h3 passlock starting issue, how to reset factory lock on h3, GM Theft Deterrent System Problem, gm passlock 1 bypass instructions

Peugeot 306 Timing belt replacement Removal And Installation Manual

0

Filed Under (Peugeot Manuals) by admin on 23-02-2011

download
Removal Removal Raise and support front of vehicle. 1. Remove: RH front wheel. Engine undershield (if fitted). Lower inner wing panel. Auxiliary drive belt(s). 307: Engine tie-bars. Crankshaft pulley [1] . Timing belt upper cover [2] . Timing belt centre cover [3] . Timing belt lower cover [4] . 2. Turn crankshaft to setting position. Insert timing pins in camshaft sprocket and flywheel [5] & [6] . 3. Slacken tensioner nut to release tension on belt [7] . Lightly tighten nut. 4. Remove timing belt. 5. Installation – -1997 Installation – -1997 Ensure timing pins located correctly [5] & [6] . 1. Fit timing belt in following order: Crankshaft sprocket. Camshaft sprocket. Water pump sprocket. 2. Manufacturer: Peugeot Model: 306 (93-97) 1,4 Engine code: TU3M/Z (KDZ) Output: 55 (75) 5800 Tuned for: R-Cat Year: 1993-97 – Tensioner pulley. NOTE: Ensure belt is taut between sprockets on non-tensioned side. Slacken tensioner nut [7] . Turn tensioner anti-clockwise to tension belt. Temporarily tighten nut. 3. Remove timing pins [5] & [6] . 4. Attach tension gauge to belt at [8] . Tool No.(-).0192/SEEM C.Tronic 105.5. 5. Slacken tensioner nut [7] . 6. Tension belt as follows: 7. Turn tensioner anti-clockwise until tension gauge indicates 45 SEEM units. 8. Tighten tensioner nut to 20 Nm [7] . 9. Remove tension gauge. 10. Turn crankshaft four turns clockwise to setting position. 11. Ensure timing pins can be inserted [5] & [6] . 12. Wait 1 minute to allow belt to settle. 13. Apply firm thumb pressure to belt at . 14. Attach tension gauge to belt at [8] . Tool No.(-).0192/SEEM C.Tronic 105.5. 15. Slacken tensioner nut [7] . 16. Turn tensioner anti-clockwise to tension belt. New belt: 40 SEEM units. Used belt: 36 SEEM units. 17. Tighten tensioner nut to 20 Nm [7] . 18. Remove tension gauge [8] . 19. Turn crankshaft two turns clockwise. 20. Ensure flywheel timing pin can be inserted [6] . NOTE: DO NOT allow crankshaft to turn anti-clockwise. 21. Attach tension gauge to belt at [8] . Tool No.(-).0192/SEEM C.Tronic 105.5. 22. Check tension gauge reading. New belt: 51±3 SEEM units. Used belt: 45±3 SEEM units. 23. Install components in reverse order of removal. 24. Tighten crankshaft pulley bolts to 8 Nm [9] . 25. Installation – 1997- Installation – 1997- Ensure timing pins located correctly [5] & [6] . 1. Fit timing belt in following order: Crankshaft sprocket. Camshaft sprocket. Water pump sprocket. Tensioner pulley. NOTE: Ensure belt is taut between sprockets on non-tensioned side. 2. Slacken tensioner nut [7] . Turn tensioner anti-clockwise to tension belt. Temporarily tighten nut. 3. Remove timing pins [5] & [6] . 4. Attach tension gauge to belt at [8] . Tool No.(-).0192/SEEM C.Tronic 105.5. 5. Slacken tensioner nut [7] . 6. Tension belt as follows: 7. Remove cylinder head cover. 8. Install valve spring compressor. Tool No.0132AE [10] . 9. Turn tensioner anti-clockwise until tension gauge indicates the following: Except 307: 31 SEEM units. 307: 44 SEEM units.

Related Content:

videos on removal of tensioner pulley on 2005 dodge neon, MERITOR HUB A433T4232, volvo penta 5 belt tighten, remove right timing belt cover 2004 axiom, HUB A433T4232, peugeot 307 camshaft repair, what tool to release tension from automatic tensioner 2007 impala, picture belt assembly on 98 4 3 volvo penta, peugeot pdf belt, how to get the serpentine belt on a volvo penta 4 3 gxi

1992 Toyota Cressida Wiring Diagram

0

Filed Under (Toyota Manuals) by admin on 30-11-2011

download
tem Wire ColorPolarity Wire Location 12V white – white/red Positive (+) steering column Starter black/white Positive (+) steering column Starter 2 none Ignition black/yellow Positive (+) steering column 2nd Ignition black/red Positive (+) steering column 3rd Ignition none Accessory blue/red Positive (+) steering column Accessory 2 none Tachometer black/yellow check conn(ig-) Power Door (Lock) Wiring Diagram for [ Negative (-) ] Door Lock green/red Negative (-) pass kick or theft ecu Power Door (Unlock) Wiring Diagram for [ Negative (-) ] Door Unlock green/whiteNegative (-) pass kick or theft ecu Door Trigger red/white Negative (-) theft ecu[1] Dome Supervision Wiring Diagram for [ none ] Dome none none none Headlights red/yellow Negative (-) steering column Parklight Positive green Positive (+) dimmer controll or dkp Parklight Negative green/whiteNegative (-) steering column Wipers blue/black Positive (+) steering column Left Front Window (Up/Down) grn/wht – red/blu in drivers door Right Front Window (Up/Down) pnk/blk – pnk in drivers door or dkp Left Rear Window (Up/Down) red – red-yel A in drivers door or dkp Right Rear Window (Up/Down) grn/blk – red/blk A in drivers door or dkp Trunk/Hatch Pin red/white Negative (-) at light, or theft ecu Hood Pin tied with doors Trunk/Hatch Release Wiring Diagram for [] Trunk/Hatch none Factory Alarm (Arm) arms with lock Factory Alarm (Disarm) disarms with unlock Horn white/red Negative (-) st.column or theft ecu Brake green/black Positive (+) brake switch Door Motor (Lock) none none none Door Motor (Unlock) none none none

Related Content:

toyota matrix ecu diagram, ECU power steering module diagram 2009 Toyota Matrix, igt savp parts diagram

2002 Honda RSX Starter Removal and Installation Manual

0

Filed Under (Honda Manuals) by admin on 17-05-2011

download
Removal 1. Make sure you have the anti-theft codes for the radio, then write down the customer’s radio station presets. 2. Disconnect the negative cable from the battery first, then disconnect the positive cable. 3. Disconnect the knock sensor connector. 4. K20A3 engine: Disconnect the bolt securing the harness bracket. 5. K20A2, K20Z1 engines: Remove the front subframe damper. 6. K20A2, K20Z1 engines: Remove the bolt (A) securing the harness bracket, then remove the intake manifold brackets (B) 7. Disconnect the starter cable (A) from the B terminal on the solenoid, then disconnect the BLK/WHT wire (B) from the S terminal. 8. Remove the two bolts holding the starter, then remove the starter. K20A3 engine K20A2, K20Z1 engines Installation 1. Install the two bolts holding the starter. 2. Connect the starter cable (A) from the B terminal on the solenoid, then connect the BLK/WHT wire (B) from the S terminal. Make sure the crimped side of the ring terminal is facing out. K20A3 engine K20A2, K20Z1 engines 3. K20A2, K20Z1 engines: Install the bolt (A) securing the harness bracket, then Install the intake manifold brackets (B) 4. K20A2, K20Z1 engines: Install the front subframe damper. 5. K20A3 engine: Connect the bolt securing the harness bracket. 6. Connect the knock sensor connector. 7. Connect the positive cable to the battery first, then connect the negative cable. 8. Start the engine to make sure the starter operates properly. 9. Enter the anti-theft codes for the radio, then enter the customer’s radio station presets. 10. Set the clock. 11.2002-2004 models: Do the engine control module (ECM) /powertrain control module (PCM) idle learn procedure. 12. Do the power window control unit reset procedure.

Related Content:

2006 chevrolet cobalt starter removal instructions, 05 kia sedona starter bolts, 2002 chevy impala starter repla, 2002 chevy impala starter replacement, how do you change a starter on a 2002 chevy impala, how to replace a starter on a 2001 mitsubishi diamante, kia sorento starter motor diagram, replacing starter on 2002 impala

2000 CHEVY TAHOE OVER-AXLE CAT-BACK REMOVAL AND INSTALLATION INSTRUCTIONS

0

Filed Under (Chevy Manuals) by admin on 13-12-2011

download
HARDWARE AND PARTS LIST TOOLS REQUIRED FOR REMOVAL AND INSTALLATION 1. 15mm Combo Wrench 2. 9/16″ Combo wrench 3. 9/16″ Socket 3/8″ Drive 4. 3/8″ Drive Ratchet 5. 7/16″ Combo Wrench 6. Tube Cutter/ or other metal cutting tool Pry bar Hardware List (1) 3″ Muffler Clamp (2) 3/8″ X 16 X 2½” Hex Bolts (2) 3/8″ X 16 Flange Nuts (2) 3/8″ Flat Washers (1) Anti-Seize Tube (1) 3″ Stainless Band Clamp Parts List (1) 3″ Inlet Tube (1) 5″ X 10″ X 24″ Muffler with 3″ Single Inlet and 3″ Single Outlet (1) 3″ Over Axle Tail Pipe 4″ Truck Tip (polished) REMOVAL AND INSTALLATION INSTRUCTIONS Removal 1. Raise vehicle using a hoist or floor jack and jack stands. 2. Locate the 2-bolt flange, which connects the y-pipe to stock cat-back. Remove the 2 nuts with a 15mm wrench. 3. Proceed to remove 3 rubber hangers. NOTE: Some type of lube will make your job easier. 4. It may be necessary to cut the stock system to aid in removal. NOTE: Lowering spare tire may aid in removing stock exhaust. Installation 1. Start by locating the inlet tube from your kit with the 2-bolt flange. Slide the inlet tube into place and attach rubber hanger at forward most position and secure the 2-bolt flange using stock hardware. 2. Slide muffler into inlet tube and secure with the provided 3″ muffler clamp. Do not fully fasten; final adjustments will be made later. 3. Once the muffler is attached install over axle tailpipe, 2 rubber factory Hangers to tailpipe and secure tailpipe to muffler using the two 3/8″ X 16 X 2½” hex bolts, two 3/8″ washers and two 3/8″ X 16 flange nuts. Final adjustments can be made and system can be fully tightened. 4. Slide the supplied 4″ polished tip over tailpipe and secure with 3″ stainless band clamp.

1997-2001 FORD EXPEDITION ELECTRICAL LAMP – AIR SUSPENSION LAMP ILLUMINATED – DIAGNOSTIC TROUBLE CODES (DTC’S) B2140 OR C2140 – RIDE HEIGHT RESET PROCEDURE

0

Filed Under (Ford Manuals) by admin on 26-01-2012

download
SUSPENSION, AIR SUSPENSION DIAGNOSTIC TROUBLE CODES (DTC’S) B2140 OR C2140 RIDE HEIGHT RESET PROCEDURE ELECTRICAL LAMP – AIR SUSPENSION LAMP ILLUMINATED – DIAGNOSTIC TROUBLE CODES (DTC’S) B2140 OR C2140 – RIDE HEIGHT RESET PROCEDURE SERVICE PROCEDURE AIR SUSPENSION DTC’S THAT ARE PRESENT NOTE BEFORE ADDRESSING B2140/C2140. DURING PDI (PRE-DELIVERY INSPECTION) IF WARNING “CK SUSP” LIGHT IS ON, PRIOR TO SENDING WARNING: BEFORE REPLACING ANY AIR TO SERVICE, VERIFY SWITCH IN UPPER RIGHT SUSPENSION COMPONENTS, HOISTING, KICK PANEL IS ON. THIS SWITCH IS TURNED JACKING, OR TOWING, DISCONNECT POWER OFF DURING VEHICLE SHIPMENT TO PREVENT TO THE SYSTEM BY TURNING OFF THE AIR MODULE FROM SEEKING TRIM HEIGHT WHILE SUSPENSION SWITCH LOCATED IN THE RIGHT SECURED DOWN FOR TRANSPORT. KICK PANEL AREA TO PREVENT VEHICLE NOTE DAMAGE OR PERSONAL INJURY. AN INADVERTENT B2140 OR C2140 MAY RAS ONLY – CLEAR 2140 RESULT IF A PARAMETER RESET (CLEAR RIDE HEIGHT) IS SELECTED UNDER NGS ACTIVE NOTE COMMANDS, THEN CANCELLED OUT. EVEN RAS (4X2) EQUIPPED VEHICLES REQUIRE STORING RIDE HEIGHT AND NOTE TOGGLING FRONT TO “ON” TO CLEAR A CK THE AIR SUSPENSION CONTROL MODULE SUSP LIGHT/2140 CODE. THIS ALLOWS THE PART NUMBER IS INTERCHANGEABLE MODULE TO STORE THE VOLTAGE WITH NO BETWEEN THE REAR AIR SUSPENSION (RAS) FRONT HEIGHT SENSOR PRESENT, AND MUST AND 4-WHEEL AIR SUSPENSION (4WAS) BE DONE EVEN WITH CONVENTIONAL (STEEL SYSTEMS, BUT ONCE THE MODULE IS COIL) FRONT SUSPENSION. INSTALLED, THE VEHICLE WILL THEN DETERMINE WHETHER VEHICLE IS 4X2 (RAS)

Related Content:

conventional colored front end 2wd suspension diagrams for ford f150 xlt 2001, scymatic 2003 f53 suspension, 99 yukon front suspension diagram, diagram of chrysler 300 front suspension, diagram of front suspension on 2000 ZR2, dodge ram 2500 front suspension diagram 2002, front solenoid code for acura integra 97, hhr rear suspension diagram, How do I replace the spindle bearing on a 1991 Jaguar XJ6, how do you clear DTC codes on 1994 saturn sl1

Honda Navigation System Information and DVD Information and Inspection Manual

0

Filed Under (Honda Manuals) by admin on 06-07-2012

download
REVISION SUMMARY •Under BACKGROUND, more sources for navigation service and user information are listed. •Under DVD LABEL COLOR IDENTIFICATION BY MODEL, the Latest DVD Version available is updated. •Under REPLACING THE NAVIGATION CONTROL UNIT AND TRANSFERRING THE NAVIGATION DVD, a step was added to Save Users Memory when replacing the navigation control unit. •Under ENTERING THE ANTI-THEFT CODE, the instructions about obtaining the serial number from a navigation unit without removing it were clarified. •Under NAVIGATION SYSTEM PLATFORMS, HFL was added to the list of Distinguishing Features . BACKGROUND Use this information to avoid possible customer dissatisfaction issues caused by incorrect or outdated DVD installation. For more information about the navigation system and its operation, refer to the following resources: •Service Manual – Printed or on ISIS •Quick Start Guide •Online University – Use the keyword NAVI . •Navigation System Manual – Besides the one that comes with the vehicle, the navigation system manual is also available online. Select SEARCH BY PUBLICATION , select Consumer Information , select your applicable vehicle, then select Navigation Manual from the list. •Service Bulletins – Use the keyword NAVI . •ETM (electrical troubleshooting manual) This bulletin provides the following navigation system DVD service information: •DVD label color identification by model •Earliest DVD version application for each model •How to identify navigation DVD versions •Checking a DVD for damage •Ordering a DVD •Navigation DVD stocking concerns •DVD handling and cleaning •Installing a navigation DVD •Precaution on customer “sneak previews” of a newer navigation DVD version •Answering customer questions about navigation coverage and POI (point of interest) •Pitfalls when interchanging navigation DVD/parts during diagnosis •Replacing the navigation control unit and transferring the navigation DVD •Entering the anti-theft code •Navigation system platforms VEHICLES AFFECTED • 2003-09 Accord • 2005-07 Accord Hybrid • 2006-09 Civic • 2006-09 Civic Hybrid • 2007-09 CR-V • 2009 Element • 2009 Fit • 2000-09 Odyssey • 2003-09 Pilot • 2006-09 Ridgeline WARRANTY CLAIM INFORMATION None. This service bulletin is for information only. Refer to the flat rate manual whenever servicing or repairing the navigation system

Related Content:

manual lincoln navigator 2007, c1998 module calibration failure navigator 2006, reset liftgate lincoln, honda elysion ecu pin voltage, service manual for civic 2007, 2005 odyssey service manual free, 2003 honda odyssey service manual, exploded view 4r55e, hubsan x4 manual pdf, how to turn off air suspension on 07 lincoln navigator

1994 Ford Thunderbird LX FUSES AND CIRCUIT BREAKERS MANUAL

0

Filed Under (Ford Manuals) by admin on 26-06-2012

download
2 – 6-Amp Circuit Breaker Windshield Wiper & Washer Pump, Interval Wiper 3 – Not Used 4 – 15 Amp Taillights, License & Parking Lights, Side Marker & Coach Lights, Cluster Illumination Lights, Radio & Clock Illuminator, A/C-Heater Illumination 5 – 15 Amp Turn Signal & Back-Up Lights, Keyless Entry Illumination, Day/Night Mirror, Turbo Overboost Buzzer 6 – 20 Amp Heated Back Light Control, Deck Lid Release, Electronic Chime Module, Lights Outage & Clock Display, Cornering & Rear Reading Lights, Tripminder, Illuminated Entry, Anti-Theft Module, Radio & Cluster Illumination 7 – 15 Amp Foglights (Turbo Only) 8 – 15 Amp Courtesy & Glove Box Lights, Key Warning Buzzer, Illuminated Entry Module, Remote Electric Mirrors, Electronic Radio & Cluster Memories, Anti-Theft Relay & Clock 9 – 30 Amp A/C-Heater Blower Motor 10 – 20 Amp Horn, Cigarette Lighter, Flash-To-Pass Feature, Fuel Filler Door, Speed Control 11 – 20 Amp Radio, Power Antenna, Sound Amplifier 12 – 20-Amp Circuit Breaker Power Seat & Door Locks, Keyless Entry, Fuel Filler Door Lock 13 – 5 Amp Instrument Cluster, Radio, Climate Control, Instrument Panel Illumination 14 – 20-Amp Circuit Breaker Power Windows, Power Moon Roof 15 – 10 Amp Taillights, Parking Lights, License & Coach Lights 16 – 4 Amp EATC Memory, Horn, Cigarette Lighter 17 – 15 Amp Electronic Cluster Tripminder, Fuel Gauge, A/C Clutch, Speed Control Module, Graphic Warning Module 18 – 10 Amp Warning Indicator Lights, Auto Light System, Electronic Chimes, Low Washer Fluid Light, Low Fuel Module, Throttle Solenoid Positioner, Low Oil Relay, Tachometer, Flash-To-Pass Relay

Related Content:

1994 thunderbird eatc, ford f650 reverse light switch, fuse location on 1994ford thunderbird

2000-2004 Toyota Tundra 4.7L V-8 Two and Four Wheel Drive Installation Manual

0

Filed Under (Toyota Manuals) by admin on 27-03-2012

download
1. Place vehicle in a location where the floor is solid and flat, with adequate lighting. Do not attempt to work on a hot engine. Heat causes metal to expand and makes removal of fasteners difficult at best. Disconnect the battery cables from the battery. Raise the front of the vehicle to obtain adequate access to the bottom exhaust manifold flanges. Use large-base jack stands to support the vehicle. Do not rely on the jack! Block the tires to prevent the vehicle from rolling off the jack stands. 2. Spray WD-40 or some type of penetrating oil on all accessible fasteners and fittings before attempting to remove them. 3. From underneath the vehicle disconnect the exhaust system from the exhaust manifolds by unbolting the (3) bolts at the collectors. Then unbolt the driver side catalytic converter from the exhaust assembly and temporarily remove it from the vehicle. PASSENGER SIDE 4. On the passenger side remove the (4) bolts attaching the heat shields to the factory manifold. 5. Next, carefully unplug the O2 sensor from its harness. 6. Now remove the nuts attaching the factory manifold to the cylinder head. With the manifold out of the way remove the mounting studs from the cylinder head. 7. Using a small wire brush or similar instrument, clean any carbon deposits left on the head surface. Be careful not to gouge the aluminum head. 8. Transfer the O 2 sensor from the factory manifold to the new passenger side header. Apply a small amount of anti seize to the threads for the sensor before installing it in the new header. Use caution not to drop or damage the sensor, they are fragile. 9. Now you are going to install the new JBA Header, but first there is some preparation of the hardware required. Apply anti seize to the threads of the new fasteners. Install the new JBA Header using the supplied gasket and fasteners. Torque to 23 ft./lbs. DRIVER’S SIDE 10. Just like you did in step (4) remove the (4) bolts attaching the heat shields to the driver side factory mani- fold. 11. Next, carefully unplug the O2 sensor from its harness. Unbolt the dipstick bracket from the head and remove the dipstick tube. 12. Remove the nuts attaching the factory manifold to the cylinder head. With the manifold out of the way remove the mounting studs from the cylinder head. 13. Using a small wire brush or similar instrument, clean any carbon deposits left on the head surface. Be careful not to gouge the aluminum head. 14. Transfer the O 2 sensor from the factory manifold to the new driver side header. Apply a small amount of anti seize to the threads for the sensor before installing it in the new header. Use caution not to drop or damage the sensor, they are fragile. 15. As you did on the passenger side, prepare the hardware before installing the driver side header. Apply anti seize to the threads of the new fasteners. Install the new JBA Header using the supplied gasket and fasteners. Torque to 23 ft./lbs. Re-install the dipstick tube. 16. Install the driver side catalytic converter. 17. Connect the exhaust system to the new headers using hardware and gaskets supplied. Reconnect O2 sensors. 18. Check to insure adequate clearance between header and shifter cable (small cable that runs from firewall, to brace on fender well, to transmission) . More clearance can be gained by adjusting (bending) brace on fender well. 19. Recheck everything

Related Content:

2004 honda civic head bolt torque, 4y toyota head torque

4.6L Mustang Bassani Mid Length Headers INSTALLATION INSTRUCTIONS

0

Filed Under (Ford Manuals) by admin on 05-12-2011

download
INSTALLATION INSTRUCTIONS 1. Disconnect the battery. 2. Safely raise & support vehicle to a comfortable working height. (One jack stand at each corner of vehicle.) 3. Spray attaching hardware and base of o2 sensors with WD40 or similar Lubricant. Remove 02 sensors from stock system. (Be careful not to damage or contaminate sensor). Stock gasket will be re-used upon assembly. 4. Remove both connector tubes between stock exhaust manifold and Bassani Modular X pipe. It may be necessary to loosen downstream clamps on the Bassani Modular X pipe. 5. Loosen EGR fitting on drivers side exhaust manifold. It will be necessary to remove nuts from the motor mounts at the K member to jack engine up. Motor mount heat shields have to be removed. 6. Loosen & remove both exhaust manifolds. 2 valve, stock manifold gaskets, depending on condition, may be re-used . Remove studs from both sides. Use supplied, and/or stock hardware. See note following #10. 7. Label wiring on starter and remove it. (Will be necessary for header installation) 8. You may also need to remove oil filter to ease installation and tightening on drivers’ side. 9. IMPORTANT! It will be necessary to unbolt steering shaft from rack. With a marker draw a straight line on shaft down to rack to index them both. Do not move front wheels or steering wheel. 10. It will be necessary to lift engine up enough to slide header tubes in and have access to install supplied header bolts. After loosening motor mount bolts, lifting engine (using a wooden block under oil pan) and removing motor mounts, one side at a time only, will ease installation. Removal of motor mounts is not mandatory. **Anti seize must be applied to all threads (header bolts and studs). It may be necessary to use a combination of header bolts and stock studs & nuts on certain tubes due to clearance between the tube and hardware. ie; stud nut or header bolt. The use of either is the installers preference. 11. Start on passenger side, with tube #1R. Push as far forward as possible to allow clearance for #2R. Once #2R is in position, install gaskets, and header bolts. When this is completed commence installation of #3R and #4R tubes following previous procedure. Leave bolts loose, DO NOT TIGHTEN UNTIL COLLECTOR IS INSTALLED. 12. When Collector R is ready for right side, place Bassani anti seize jet lube , on slip connectors to ease installation. When collector lines up with tab on header tube, fasten them together and tighten all header tubes. 13. When all hardware is properly tightened, lower engine, re-install motor mount hardware, starter and O2 sensors in collector. The use of Bassani anti seize Jet Lube is recommended on O2 sensor threads. Do not to contaminate O2 sensor bulb with lube. 14. Proceed to drivers’ side. Install #1L with gasket installed. Install supplied fasteners with Bassani anti seize jet lube on the threads. DO NOT TIGHTEN ALL THE WAY, leave semi loose. Install tube #3L, then #2L. You will need to experiment with pipes #2L and #3L. #2L will slip between #3L and #1L. Now install #4L, fasten and screw air fitting to tube #4L. Install Collector L . When collector tab lines up with header tab, tighten all hardware, and bolt on EGR, and any smog fittings. Lower engine and re-install motor mount hardware. Reconnect steering shaft using loctite 271 thread locker on bolt.

Related Content:

2002 chevy s10 exhaust flange seal, ebay ford 555 backhoe cheap service manual, replacing choke heater tube in 57 chevy exaust manifold

Related Content:

p1626 chevy venture, 87 bonco 2 parking brake control assembly diagram, what is a class 2 malfunction, VTD? chevrolet, universal theft deterrent system for 1996 bonneville, theft deterrent module location 99 olds intrigue, hummer h3 passlock starting issue, how to reset factory lock on h3, GM Theft Deterrent System Problem, gm passlock 1 bypass instructions