schematic diagram power steering hose chrysler

You search PDF repair manual about schematic diagram power steering hose chrysler, if there are search results will appear below. If search results do not exist, please search by others keyword.



  schematic diagram power steering hose chrysler Direct Download speed 5432 Kb/s

  schematic diagram power steering hose chrysler Full Version speed 8172 Kb/s



1995-1999 Buick Riviera Steering Vibration/Shudder/Moan During Parking Maneuvers on Dry Pavement (Install Power Steering Pressure (Inlet) and/or Return (Outlet) Hose Assembly)

0

Filed Under (Buick Manuals) by admin on 11-02-2012

download
1. Verify that the power steering pump reservoir is full. 2. Verify that the accessory drive belt is in good condition and that the pulleys are not bent or damaged. 3. Verify proper belt tension and operation of the belt tensioner. 4. Check for power steering hose ground out conditions. 5. Check for good engine idle and correct engine RPM. 6. Check to see that the rear transaxle mount does not have a plastic assembly aid installed which is used Subject: Steering Vibration/Shudder/Moan During Parking Maneuvers on Dry Pavement (Install Power Steering Pressure (Inlet) and/or Return (Outlet) Hose Assembly) Models: 1995-99 Buick Riviera 1997-2001 Buick Park Avenue, Ultra 2000-2001 Buick LeSabre 2000-2001 Pontiac Bonneville • 1995-98 Buick Riviera • 1997-98 Buick Park Avenue and Ultra • 1999 Buick Riviera • 1999-2001 Buick Park Avenue and Ultra • 2000-2001 Buick LeSabre • 2000-2001 Pontiac Bonneville • If fluid level is low, fill and check for leaks. • If power steering system has air in the system, perform the “Bleeding Air from Power Steering System” procedure as described in the Power Steering System sub-section of the Service Manual. Important: When performing the “Bleeding Air from Power Steering System” procedure, it is important that the front of the vehicle is supported by the lower control arms. If the vehicle is not supported by the lower control arms, the procedure may cause the strut bushing to dislocate and cause new concern. for assembly purposes. If the assembly aid is installed, remove the assembly aid and install the rear transaxle mount. 7. With the vehicle on dry pavement, maneuver the vehicle in parking positions. If the steering vibrates/shudders or moans in this test, replace the power steering pressure hose and/or the harmonic balancer. Important: A defective harmonic balancer on the 1995 Buick Riviera can influence steering vibrations after power steering hose installation. Important: When installing the pressure hose on the 1995 Buick Riviera, pull down on the pressure hose at the rear of the engine or bend the hose to allow clearance between the hose and the front of the dash. Power Steering Pressure (Inlet) Hose Replacement Procedure For 1995-1998 Vehicles: 1. Raise and suitably support the vehicle. Refer to Vehicle Lifting and Jacking in the General Information section of the Service Manual. 2. Drain the power steering fluid. Refer to Draining the Power Steering System in the Power Steering section of the Service Manual. 3. Remove the power steering gear assembly heat shield (1). 4. Disconnect the power steering pressure hose from the power steering pump assembly (4). 5. Remove the bolt/screws from the retaining clips (3). 6. Disconnect the power steering pressure hose from the power steering gear assembly (2). 7. Remove the power steering pressure hose assembly from the vehicle. 8. Install the power steering pressure hose assembly to the vehicle. 9. Connect the power steering pressure hose to the power steering pump assembly (4). 10. Connect the power steering pressure hose to the power steering gear assembly (2). Tighten Tighten the power steering pressure hose to the steering gear to 27 N·m (20 lb ft). 11. Install the bolt/screws to the retaining clips (3). Tighten Tighten the retaining clip bolt/screws to 6 N·m (53 lb in). 12. Install the power steering gear assembly heat shield (1). 13. Lower the vehicle. 14. Fill and bleed the power steering system using, J 43485. Refer to Corporate Bulletin Number 83-32-09, dated November, 1998. Power Steering Pressure (Inlet) and Return (Outlet) Hose Replacement Procedure For 1999-2001 Vehicles: 1. Raise and suitably support the vehicle. Refer to Vehicle Lifting and Jacking in the General Information section of the Service Manual. 2. Drain the power steering fluid. Refer to Draining the Power Steering System in the Power Steering section of the Service Manual. 3. Remove the LH front wheel/tire assembly. 4. Remove the LH lower splash shield. 5. Remove the lower radiator air deflector (engine splash shield, if installed.

Related Content:

how to remove trumpet off of ford 2000 tractor, steering pressure hose replacement f250 - 7 3 - 4wd, Rav 4 steering rack dismantle and refit procedure, 99 buick park ave radiator installation, how to change power steering pump 2009 acada, how to replace 2003 impala power steering pump, exploded view of a tilt steering column for 2001 plymouth neon 2 0l, 98 amigo isuzu how to remove power steering pump, youtube replace the hub on a meritor ff981 axle, schematic for 99 taurus power steering

2000 Dodge Dakota & Durango Power Windows ADJUSTMENTS

0

Filed Under (Dodge Manuals) by admin on 18-06-2012

download
ADJUSTMENTS WINDOWS Remove door trim panel. See DOOR TRIM PANEL under REMOVAL & INSTALLATION. Loosen bolts holding window to regulator. Raise window fully, seating window in frame. Tighten bolts. Install door trim panel. TROUBLE SHOOTING POWER WINDOWS On Dakota, inspect circuit breaker No. 20 (20-amp) in junction block. On Durango inspect circuit breaker No. 21 (25-amp) in junction block. On all models, junction block is located on left end of instrument panel. Inspect fuse No. 9 (40-amp on Dakota, 50-amp on Durango) in Power Distribution Center (PDC). PDC is located in left front corner of engine compartment. Inspect power window system ground circuit. See WIRING DIAGRAMS . SYSTEM TESTS ALL WINDOWS INOPERATIVE Dakota 1. Check circuit breaker for power window system. See TROUBLE SHOOTING . Replace circuit breaker as necessary. If circuit breaker is okay, go to next step. 2. Disconnect negative battery cable. Remove driver’s front power window switch. See POWER WINDOW SWITCH under REMOVAL & INSTALLATION. Check for continuity between ground and terminal No. 3 (Black wire) at driver power window switch wiring harness connector. If continuity exists, go to next step. If continuity does not exist, repair open in Black wire between driver power window 2000 Dodge Durango 2000 ACCESSORIES & EQUIPMENT’ ‘Power Windows – Dakota & Durango 2000 Dodge Durango 2000 ACCESSORIES & EQUIPMENT’ ‘Power Windows – Dakota & Durango switch connector and ground. See WIRING DIAGRAMS . 3. Connect negative battery cable. Turn ignition on. Measure voltage between ground and terminal No. 5 (Tan wire) at driver’s power window switch wiring harness connector. If battery voltage is present, check driver power window switch. See POWER WINDOW SWITCH under COMPONENT TESTS. If battery voltage is not present, repair open Tan wire between driver power window switch connector and ignition switch. See WIRING DIAGRAMS . See POWER DISTRIBUTION article in WIRING DIAGRAMS. Durango 1. Check circuit breaker for power window system. See TROUBLE SHOOTING . Replace circuit breaker as necessary. If circuit breaker is okay, go to next step. 2. Disconnect negative battery cable. Remove driver’s front power window switch. See POWER WINDOW SWITCH under REMOVAL & INSTALLATION. 3. Check for continuity between ground and terminal No. 5 (Black wire) at driver’s power window switch wiring harness connector. If continuity exists, go to next step. If continuity does not exist, repair open in Black wire between driver’s power window switch connector and ground. See WIRING DIAGRAMS . 4. Reconnect negative battery cable. Turn ignition on. Measure voltage between ground and terminal No. 4 (Tan wire) at driver’s power window switch wiring harness connector. If battery voltage is present, check driver’s power window switch. See POWER WINDOW SWITCH under COMPONENT TESTS. If battery voltage is not present, repair open Tan wire between driver power window switch connector and ignition switch. See WIRING DIAGRAMS . See POWER DISTRIBUTION article in WIRING DIAGRAMS. ONE WINDOW INOPERATIVE

Related Content:

1993 dakota 3 9 fuse diagram, lucas a127 wiring, free 1997 buick regal gs wiring diagrams, 1998 Dodge Dakota Service Manual, abs and Anti Theft Passive 2000 mercury cougar, dodge durango 2002 suspension layout, zimmatic pivot wiring, 2003 s10 airbag wiring diagram, lazy boy recliner mechanism diagram, 2000 Buick LeSabre Wiring Diagram

2005-2008 Honda Odyssey Power Steering Pump Whines , Buzzes, or Hums Repair Manual

0

Filed Under (Honda Manuals) by admin on 16-05-2012

download
Inspect the power steering reservoir. Does one of the 3 ribs on the reservoir cover point toward the reservoir holder? Yes – This vehicle already has the revised power steering reservoir. Continue with normal troubleshooting procedures. No – Go to REPAIR PROCEDURE. REPAIR PROCEDURE 1. Drain the power steering reservoir: •Remove the reservoir from its holder. •Raise the reservoir, and disconnect its return hose. •Drain the reservoir fluid into a suitable container. Take care not to spill any fluid on the body or other parts. Wipe off any spilled fluid immediately. 2. Drain the fluid from the power steering system: •Connect a suitable diameter drain hose to the disconnected return hose. •Hold the end of the drain hose in a suitable container. •Start the engine, and run it at idle while you turn the steering wheel lock-to-lock several times. •When the fluid stops running out of the hose, shut off the engine. •Discard the used fluid. 3. Reinstall the return hose to the reservoir, then reattach the reservoir to its holder. Fill the reservoir to its upper level line with new power steering fluid. 4. Bleed the air from the power steering system: •Start the engine. •With the engine at a fast idle, turn the steering wheel lock-to-lock several times. 5. Check the condition of the fluid in the reservoir: •If the fluid looks contaminated, dark, or discolored, repeat steps 1 thru 5. •If the fluid is clear, go to step 6. 6. Place a suitable container under the vehicle to catch any fluid 7. Replace the power steering fluid reservoir: •Remove the reservoir from its holder. •Disconnect the return hose from the reservoir, and pour the fluid from the reservoir into a container. •Disconnect the outlet hose from the reservoir, and remove the reservoir. •Install a new reservoir in the reverse order of removal. •Fill the reservoir to its upper level line with new power steering fluid. 8. Start the engine, and run it at a fast idle. Turn the steering from lock-to-lock several times to bleed any air from the system. 9. Recheck the fluid level in the reservoir, and add more if needed. Do not fill the reservoir beyond its upper level line.

Related Content:

2011 cruze recall leaking radiator fluid, mazda b2000 electronic ignition pdf, toyota dyna clutch fluid reservoir, washer fluid low silverado trucks

TOYOTA RAV4 STEERING INTERMEDIATE SHAFT NOISE SERVICE MANUAL

0

Filed Under (Toyota Manuals) by admin on 25-01-2012

download
Repair Procedure 1. Install a steering wheel holder. NOTE: Ensure the wheels are straight and the steering wheel is centered before removing the steering intermediate shaft by installing a steering wheel holder. 2. Remove the column hole cover silencer sheet. Turn back the floor carpet, remove the 2 clips, and remove the column hole cover silencer sheet. Production Change Information Parts Information Repair Procedure STEERING INTERMEDIATE SHAFT NOISE – ST001-08 February 8, 2008 Page 3 of 4 3. Remove the No. 2 steering intermediate shaft assembly. A. Place matchmarks (“a”) on the No. 2 steering intermediate shaft and steering column. B. Remove bolt A and detach the No. 2 steering assembly from the steering gear. C. Remove bolt B and detach the No. 2 steering intermediate shaft from the steering column. 4. Remove the No. 1 steering column hole cover sub-assembly by removing the clamp and disconnecting the column hole cover from the steering gear. 5. Remove the intermediate shaft. Remove the bolt and disconnect the steering intermediate shaft from the steering gear. 6. Install the NEW intermediate shaft onto the steering gear. Torque: 35 Nm (360 kgfcm, 26 ftlbf) 7. Install the No. 1 steering column hole cover sub-assembly onto the steering gear with a NEW clamp. Repair Procedure (Continued) B A a No. 2 Steering Intermediate Shaft Intermediate Shaft STEERING INTERMEDIATE SHAFT NOISE – ST001-08 February 8, 2008 Page 4 of 4 8. Install the No. 1 steering column hole cover sub-assembly by attaching clip B onto the body and installing the No. 1 hole cover onto the body with clip A. NOTE: Make sure that the lip of the No. 1 hole cover is NOT damaged. 9. Install the No. 2 steering intermediate shaft assembly. A. Align the matchmarks (“a”) on steering intermediate shaft and the steering sliding yoke and temporarily install them with bolt B. Torque: 35 Nm (360 kgfcm, 26 ftlbf) B. Ensure the wheels are straight. C. Install the No. 2 intermediate shaft and the intermediate shaft with bolt A. Torque: 35 Nm (360 kgfcm, 26 ftlbf) 10. Install the column hole cover silencer sheet. A. Install the column hole cover plate with the 2 clips. B. Install the floor carpet. 11. Remove the steering wheel holder from the vehicle. 12. Road test the vehicle to verify the repair and confirm that the steering wheel is centered.

Related Content:

07 ford escape intermediate drive shaftpassenger side, 2003-2011 ford crown vic intermediate steering shaft removal, 3024 CAT Rocker Shaft Assembly, 91 Dakota Intermediate Steering Shaft, 92 Dakota Intermediate Steering Shaft, cruze cam cover crack, steering pitman shaft drawing 91 dodge dakota 2 wheel drive

1997 Ford Thunderbird/ Cougar Steering Column Removal And Installation Manual

0

Filed Under (Acura Manuals) by admin on 12-04-2012

download
Steering Column Disassembly CAUTION: Do not remove the steering column, steering wheel and air bag module as an assembly from the vehicle unless the column is locked to prevent rotation, or lower end of steering shaft is wired in such a way to prevent the steering wheel from being rotated, as this will damage the air bag sliding contact. 1. Disconnect battery ground cable (14301). Refer to Section 14-01 . 2. Remove steering wheel (3600) as described. 3. Remove steering column from vehicle as described. 4. Remove steering column lower yoke (3N725), steering column upper bearing spring (3520), suspension height sensor control ring (3C131) and steering column bearing tolerance ring (3L539). Lower Steering Column Assembly 5. Remove turn indicator cancel cam (13318) by pushing up with flat-bladed screwdriver. Note direction of flush surface. 6. Remove ignition switch (11572) assembly. 7. Remove bearing retainer (3C610) and steering column upper bearing spring. . Remove steel steering column bearing tolerance ring and steering column bearing sleeve (3518). 9. Remove plastic bearing retainer from ignition switch lock cylinder bore. 10. Remove metal steering column lock housing bearing (3E700) from ignition switch lock cylinder bore. 11. Note position of steering column lock gear (3E717) to actuator lock. Remove steering column lock gear. 12. Remove two pivot bolts. Use caution becausesteering column position spring (3D655) will release when bolts are removed. Remove steering column lock cylinder housing (3511). 13. Remove steering column shaft assembly from steering column. 14. Remove steering column lock lever actuator (3E715) and steering actuator housing (3F723). 15. Remove lower steering column bearing (3517) and steering column lower bearing retainer (3D681).

Related Content:

2005 chevy s-10 streeing colum repair, mgb steering shaft removal, 2008 ford 150 wiring harness box under steering colum, 1993 chevrolet suburban steering column diagram, 1994 chevy s10 steering column wiring, silverado steering column diagram 2005, install steering Center Link on 1989 s10, how to replace steering shaft ujoint for 1992 camry in utube, how to replace shiftetr cloum on 2002 ford f 150, how to remove the steering wheel cover from 04 pontiac grand prix

2003-2007 Accord V6 Power Steering Moans or Whines Repair Manual

0

Filed Under (Toyota Manuals) by admin on 02-06-2012

download
SYMPTOM A moan or whine is heard when turning the steering wheel when the engine is cold. There may be air bubbles or foam in the power steering reservoir. The noise usually goes away when the engine warms up. PROBABLE CAUSE Air enters the power steering pump through the inlet joint O-ring. CORRECTIVE ACTION Replace the O-ring on the power steering pump inlet joint. PARTS INFORMATION O-ring: P/N 91345-RDA-A01, H/C 8811010 REQUIRED MATERIALS Honda Genuine Power Steering Fluid: P/N 08206-9002, H/C 3747284 (One container repairs about 12 vehicles.) WARRANTY CLAIM INFORMATION In warranty: The normal warranty applies. Operation Number: 5121B5 Flat Rate Time: 0.3 hour Failed Part: P/N 91345-PAA-A01 H/C 5430681 Defect Code: 07408 Symptom Code: 04201 Template ID: 07-086A Skill Level: Repair Technician Out of warranty: Any repair performed after warranty expiration may be eligible for goodwill consideration by the District Parts and Service Manager or your Zone Office. You must request consideration, and get a decision, before starting work. REPAIR PROCEDURE 1. Remove the bolt holding the inlet joint to the power steering pump housing. 2. Place a shop towel under the inlet joint. 3. Twist the inlet joint back and forth until it is loose, then carefully disconnect the joint and point the hose upward to minimize fluid loss. 4. Remove the inlet joint O-ring. 5. Apply power steering fluid to a new O-ring, and install it on the inlet joint. 6. Install the inlet joint, and torque its bolt to 11 N. m (8 lb-ft). 7. Top off the power steering fluid, if needed. Start the engine, and let it idle. Confirm that the noise is gone and that the system is operating properly

Related Content:

corvette c4 tech free pdf, HC - 8811010

2005-2006 Toyota Tundra/ Sequoia 4.7L V8 MR Tech Power-flow Intake system Installation Manual

0

Filed Under (Toyota Manuals) by admin on 23-03-2012

download
The installation of this cold air intake does require mechanical skills. Removal of engine covers, air lines and removing several plastic plugs and screws that may be difficult. It is recommended that this system be installed by a professional mechanic. Be sure to disconnect the negative terminal before proceeding. Congratulations! You have just purchased the worlds first tuned intake system. MR Technology, Leading the way! Patent pending (A) and (G) (B) (D) (A) Power-Box contents: POWER-FLOW: An air intake evolution Tools required: 1- 8mm socket 1- 10mm socket 1- 12mm socket 1- Phillips screw driver 1- 8mm nut driver 1- 55mm allen wrench 1- Disc grinder or Dremel (C) (E) Figure 1 Figure 2 Carefully, remove the mass air flow sensor from the air sensor housing to be reused later in the instruc- tions. Unhook three spring clamps from the top air box cleaner. Once the hooks have been removed, continue to detach the air box top from the lower air box cleaner. See fig. 15 for better illustration. Once the nut and bolt have been removed, continue to remove the entire hose clamp. Unplug the electrical harness clip from the mass air flow sensor as shown above. Disconnect the 4mm vacuum line located to the side of the air box cleaner. Unscrew the nut and bolt the hose clamp that secures the hose over the radiator. Loosen the two flange nuts on the engine cover in order to remove the cover. Disconnec the 6mm vacuum hose that will be reused later in the instructions. Page 2 of Part# PF2019 Unscrew the two screws from the mass air flow sensor, shown above. Loosen the hose clamp on the air duct connected to the throttle body. Unplug the crank case breather hose from the air crank case port as shown above. >>> >>>> Figure 3 Figure 8 Figure 7 Figure 6 Figure 11 Figure 10 Figure 9 Figure 14 Figure 13 Figure 12 >>>> Figure 4 Figure 5 Once the flange nuts have been removed, continue to remove the cover from the engine compartment as shown above. >>> >>> >>> >>> >>> >>> The three spring clamps shown above are unhooked from the top air box cleaner (A). Remove the air filter panel once the top has been removed (B). Once the air filter panel is removed, there are three bolts that will be removed in order to detach the lower air box cleaner. Remove the entire lower air box cleaner from the engine compartment. Place the power bands over each end of the silicone elbow. press the short end of the silicone elbow over the throttle body. Once the silicone elbow has been aligned continue to semi-tighten power band over the throttle body end. The first vibra-mount is aligned to the pre-tapped hole located behind the head lamp. The first vibra-mount is now installed as shown above. Screw the second vibra-mount is aligned over the wheel well bracket. The second vibra-mount is now installed as shown above. The stock 6mm hose is removed from the fuel pressure regulator. Press the new 16″- 4mm vacuum hose over the fuel pressure regulator port. Page 3 of Part# PF2019 Figure 15 Figure 17 Figure 16 Figure 20 Figure 19 Figure 18 Figure 23 Figure 26 Figure 25 Figure 22 Figure 21 Figure 24 (B) (A) (A) (A) >>> >>> >>> >>> Both vibra-mounts are now installed, you are now ready to go on to the next step. Place one .462 and a .412 power band over the silicone step hose. Press the 3 3/4″ side over the velocity stack as shown above. The Power box is now sitting flush over the vibra- mounts and a fender washer is placed over each vibra-mount. The last m6 flange nut is placed over the vibra- mount located behind the Power box. The 65mm bolt is tightened with an allen wrench. The assembled power box is lowered into the engine compartment. Align the mounting points on the bracket arms over the vibra-mounts. One 45mm bolt is removed from the top of the box. The bracket is place under the Power box and the 45mm bolt is aligned and screwed back in place as shown above. Remove the 65mm bolt from the velocity stack base. Align the bracket to the hole and insert the 65mm bolt back in place

Related Content:

09 cts air condition drain location, 1990 isuzu npr no power to fuse panel, mercedes benz e280 w211 2005 fuse diagrams, hitatchi ex 200 fuse box order, install 2000 celica air box, land rover freelander 2 2007 fuse box, Popping noise from air filter, replace tacoma ac drain hose, troubleshooting a mazda 6 air conditioner drain line, turn signal fuses on 2002 winnebago adventurer

1989 Toyota 4Runner STEERING COLUMN REMOVAL AND INSTALLATION INSTRUCTIONS

0

Filed Under (Toyota Manuals) by admin on 13-11-2011

download
REMOVAL & INSTALLATION STEERING COLUMN Removal 1) Disconnect battery ground cable. Remove steering wheel. On Cressida, Corolla, MR2 and Tercel models, remove fuse box cover, lower instrument trim panel and air duct from under steering column. 2) On all models, remove upper and lower steering column covers. Remove combination switch. Mark position of “U” joints and shaft for reassembly. 3) On models with “U” joints, remove “U” joint retaining bolt. On models with flexible joint, remove flexible joint retaining bolt. NOTE: On 2WD Pickup models, remove steering column with intermediate shaft attached. 4) On all models, mark position of joint and pinion shaft for reassembly. Remove intermediate steering shaft. 5) Remove floor pan cover bolts. Remove tilt bracket-to- dashboard mounting bolts. Remove steering column toward inside of vehicle. Fig. 1: Exploded View of Camry, Corolla, MR2 & Tercel Steering Column Assembly Courtesy of Toyota Motor Sales, U.S.A., Inc. Fig. 2: Exploded View of Celica, Cressida & Supra Steering Column Assembly Courtesy of Toyota Motor Sales, U.S.A., Inc. Fig. 3: Exploded View of Land Cruiser, Pickup, Van & 4Runner Steering Column Assembly Courtesy of Toyota Motor Sales, U.S.A., Inc. Installation 1) To install steering columns, reverse disassembly procedure. Grease main steering shaft and all bearings. 2) Ensure marks made to flexible couplings and to “U” joints are aligned. Ensure steering column and shafts do not bind after installation. STEERING COLUMN OVERHAUL NOTE: Camry, Corolla, MR2 and Tercel steering columns are similar. Some of the following procedures will not pertain to all models. Disassembly (Camry, Corolla, MR2 & Tercel) 1) Remove tension springs, grommets and screws from tilt bracket. Remove tilt lever left-hand set bolt. Remove column upper support lock bolt. 2) Remove tilt steering support bolts and pawl set bolts. Place bushings and “O” rings aside and keep them clean. Remove ignition lock cylinder. 3) Using a screwdriver, push 2 thrust stoppers into bearing retainers. Pull out shaft from column. Remove the No. 1 column ring, bearing retainer, thrust stoppers and No. 2 column ring from shaft. 4) Remove snap ring and lower bearing from shaft. Remove bearing inner snap ring. Remove upper bracket retaining bolts and ground strap. Separate upper bracket from column. Inspection 1) Check that steering lock mechanism operates properly. Check upper bearing for smooth rotation or excessive noise. Replace upper bearing (if necessary). 2) Using Drift (09631-00020) and Adapter (09627-30010), drive bearing from upper bracket. Pack new bearing with grease. Using the same drift and adapter used in removal, drive new bearing into upper bracket. 3) Inspect lower bearing for smooth rotation or excessive noise. If lower bearing shows signs of wear or damage, replace with a new one. Reassembly 1) Install upper bracket onto column. Install ground strap. Tighten retaining bolts to 14 ft. lbs. (19 N.m). Install inner snap ring on shaft groove nearest to center of shaft. 2) Install lower bearing and lower bearing snap ring. Place No. 2 column ring into position next to bearing on side nearest center of shaft. See Fig. 4.

Related Content:

2003 toyota camry 2 4 main crankshaftbearing removal, stearing colium cover removel 2003 buick reagel, Reinstall steering column for 1992 Toyota Camry, kia sorento front drive shaft center bearing removal, kia sorento center support bearing removal, kia sorento 2007 manual driveshaft carrier bearing, jeep upper bearing pulls out, how to remove steering column cover on 1994 mitsubishi gt3000, does the center bearing on a 2007sorento require lubrication, 2007 kia sorento center support bearing

2002 Chrysler Voyager LX Power Windows TROUBLE SHOOTING/ SYSTEM TESTS

0

Filed Under (Chrysler Manuals) by admin on 19-11-2011

download
ALL WINDOWS INOPERATIVE 1. Check power window system circuit breaker and fuse. See TROUBLE SHOOTING . Replace components as necessary. If components are okay, go to next step. 2. Remove driver’s power window switch. See POWER WINDOW SWITCH under REMOVAL & INSTALLATION. Turn ignition on. Using test light, connect ground lead to harness connector terminal No. 13 (Black/Brown wire). Check for voltage by touching test light probe to harness connector terminals No. 9, 11 and 14 (all White/Pink wires). 3. If test light does not illuminate, check power and ground circuits. See WIRING DIAGRAMS . If test light illuminates, ground circuit and power circuit between battery and switch are okay. Check switch and motor. See POWER WINDOW SWITCH and POWER WINDOW MOTOR under COMPONENT TESTS. COMPONENT TESTS VENT WINDOW MOTOR 1. Remove “D” pillar trim panel. See “D” PILLAR TRIM PANEL under REMOVAL & INSTALLATION. 2. Disconnect power vent window motor wire connector from body harness. 3. Using 2 jumper wires, connect one to a battery (+) source and the other to a good ground (-). 4. Connect the negative (-) jumper probe to one of the motor connector terminals. 5. Momentarily touch the positive (+) jumper probe to the other motor connector terminal. When the positive probe is connected, the motor should rotate in one direction to either move window open of closed. If window is all the way open or closed the motor will grunt and the crank system will flex when actuated in the one direction. Reverse jumper probes at the motor connector terminals and window should now move in the opposite position to verify full operation. If motor grunts and does not move with the motor connected in both directions, verify that crank system is not binding. POWER WINDOW MOTOR 1. Remove door trim panel and sound pad. See DOOR TRIM PANEL under REMOVAL & INSTALLATION. 2. Disconnect power window motor wire connector from door harness. 3. Using 2 jumper wires, connect one to a battery (+) source and the other to a good ground (-). 4. Connect the negative (-) jumper probe to one of the motor connector terminals. POWER WINDOW SWITCH 1. Remove window switch from door trim panel. See POWER WINDOW SWITCH under REMOVAL & INSTALLATION. Using an ohmmeter, check switch continuity. See appropriate WINDOW SWITCH CONTINUITY table. See Fig. 1 or Fig. 2 . 2. If the results are NOT OK, replace the drivers side window lift switch. 3. Test passenger door switch for continuity. 4. If the results are not OK, replace the switch. The power window master switch has a Auto-Down feature. The switch is equipped with 2 detent positions when actuating the power window OPEN. The first detent position allows the window to roll down and stop when the switch is released. The second detent position actuates an integral express roll down relay that rolls the window down after the switch is released. When the express down circuit senses stall current (window has reached end of down travel), the switch will turn current off to the motor. The AUTO feature can be cancelled by actuating the switch UP or DOWN while window is in motion. If the electronic circuit in the switch fails to detect a stall current, the auto down circuit will time out within 9 to 13 seconds.

Related Content:

starter motor repair manual, mitsubishi canter (4D35) repair manual pdf, 07 yukon 4wd left side motor mount replace, repairing power window on 2003 ford focus, remove water deflector 2000 silverado window, parts diagram 1990 grand prix 4 door drivers window, instructions on wiring a 350 motor, How to test end coder, gm stepper motor replacement, replacement of acadia thermostat

1997 Jeep Cherokee 2WD Serpentine Belt INSPECTION ADJUSTMENT REMOVAL And INSTALLATION

0

Filed Under (Jeep Manuals) by admin on 05-01-2012

download
INSPECTION When inspecting serpentine drive belts, small cracks that run across the ribbed surface of the belt from rib to rib are considered normal. If the the cracks are running along the rib (rather across), this is not normal and the belt(s) must be replaced. ADJUSTMENT It is not necessary to adjust belt tension on the 5.2L or 5.9L engines and on the 2.5L and 4.0L engines (without power steering). These engines are equipped with an automatic tensioner. The tensioner maintains correct tension at all times. 2.5L and 4.0L Engines With Power Steering See Figures 1, 2, 3 and 4 If the vehicle is not equipped with power steering, it will be equipped with an idler pulley. If equipped with an idler pulley, refer to and follow the 5.2L/5.9L belt removal and installation procedure. Loosen the pump upper pivot bolt, lower locknut and pump adjusting bolt using a ratchet and 13mm socket or a 13mm box wrench. 1. Use a belt tension gauge placed in the middle of the belt being tested. Proper tension for a new belt is 180-200 lbs. (800-900 N) and 140-160 lbs. (623-712 N) for a used belt. 2. Tighten the pump adjusting bolt to achieve proper tension and recheck the belt tension. 3. Fig. Fig. 1: Loosen the pivot bolt (1), then the locking bolt (2) to loosen the power steering pump from behind Fig. Fig. 2: Use a ratchet and 13mm size socket to rotate the power steering pump Fig. Fig. 3: Adjustment points on the 2.5L engines without power steering (rear view) Fig. Fig. 4: Adjustment points on the 2.5L engine (front view) Removal & Installation 2.5L and 4.0L Engines With Power Steering See Figures 5, 6 and 7 Fig. Fig. 5: Proper belt routing diagram can usually be found on a sticker located in the engine compartment Fig. Fig. 6: Common 4.0L engine serpentine belt routing Fig. Fig. 7: Common 2.5L engine serpentine belt routing Loosen the rear power steering pump mounting bolts using a ratchet and 13mm socket or a 13mm box wrench. 1. Loosen the pump upper pivot bolt, lower locknut and the pump adjusting bolt using a ratchet and 13mm socket or a 13mm box wrench. 2. Remove the belt. 3. To install: Install the belt. 4. Tighten the pump adjusting bolt to achieve proper tension. 5. Install the pump rear mounting bolts, pivot bolt and locknut. Tighten the bolts to 20. ft. lbs. (27 Nm). 6. Check the belt for proper tension. If tension is incorrect, refer to the adjustment procedure in this section. 7. 5.2L and 5.9L Engines See Figures 8, 9 and 10

Related Content:

1986 jeep cherokee serpentine belt route, serpintin belt diagram for 2006 jetta, kia 3 5 crank bolt for sale, jetta 2006 fan belt totation, GM 10 Bolt Rebuild Manual, gm 10 bolt instructions, 99 Jeep Cherokee Owners Manual pdf, 2010 Kia Forte Serpentine Routing Belt Diagram, 2004 honda civic serpentine belt, 1995 Jeep 2 5L ccv orfice and emissions

Related Content:

how to remove trumpet off of ford 2000 tractor, steering pressure hose replacement f250 - 7 3 - 4wd, Rav 4 steering rack dismantle and refit procedure, 99 buick park ave radiator installation, how to change power steering pump 2009 acada, how to replace 2003 impala power steering pump, exploded view of a tilt steering column for 2001 plymouth neon 2 0l, 98 amigo isuzu how to remove power steering pump, youtube replace the hub on a meritor ff981 axle, schematic for 99 taurus power steering