Skip to content

seat belt tensioner repair

You search PDF repair manual about seat belt tensioner repair, if there are search results will appear below. If search results do not exist, please search by others keyword.

1993 Mercedes Benz 190E Drive Belt Tensioner Service and Repair Manual

download
Service and Repair Notes NOTE : The belt tensioning device has been modified during production, tensioner version may vary from one vehicle to another. Early engines may be retrofit with later tensioners but requires additional parts. PROCEDURE Remove Poly V-Belt . On Tensioning Devices Without Shock Absorber NOTE : The 1st design of the tensioning device was without a shock absorber. Unbolt fixing bolt (25). Tightening torque: With 19mm hex head 75 Nm (55 ft lbs) . With 17mm hex head 80 Nm (59 ft lbs) . Remove belt tensioner.

2001 Audi A6 Quattro Sedan Timing Belt Service and Repair Manual

download
Removing -Remove engine cover-arrows-. -Remove cylinder head cover-1- and -2-. -Disengage spring clips at toothed belt cover. -Remove toothed belt cover. -Remove noise insulation -arrows-. -Removing and installing ribbed belt. See: Drive Belts, Mounts, Brackets and Accessories/Drive Belt/Service and Repair -Remove ribbed belt pulley for viscous fan. Turn crankshaft to TDC by hand. Markings -A- and -B- must be aligned. -Check position of camshafts: larger holes -arrow- in securing plates on camshaft sprockets must be in line with each other and facing inward. If not, turn crankshaft one revolution. -Remove sealing plug -arrow- from left side of cylinder block. -TDC drilling in crankshaft must be behind sealing plug hole (feel to check). -Screw clamping bolt 3242 for crankshaft into sealing plug hole and tighten -Remove tensioner for ribbed belt. -Remove vibration damper. -Remove torque support -arrows-. Note: -Mark the direction of rotation of the toothed belt with chalk or felt pen before removing. A used belt can break if it rotates in the wrong direction when reinstalled. -The toothed belt tensioning element is oil damped. To compress tensioning element apply constant pressure (compresses slowly) -Install camshaft bar T40005 onto securing plates of the two camshafts. -Loosen two camshaft bolts and unscrew approximately 5 turns. -Remove camshaft bar T40005. -Pull off both camshaft sprockets using puller T40001. -Loosen toothed belt tensioning roller (arrow). -Remove toothed belt together with camshaft sprocket for cylinder bank 1-4. Installing

1998 Chrysler Town And Country LX SERPENTINE BELT SLIPS OFF IDLER PULLEY REPAIR PROCEDURE

download
REPAIR PROCEDURE This repair is compatible with DaimlerChrysler’s Mobile Service Program and does not require hoists or other full service facility special equipment. 1. Remove the serpentine belt from around the idler pulley by rotating the tensioner clockwise ( Fig. 3 ). 2. Remove the purge duty cycle solenoid and wiring harness from the right side engine mount. 3. Remove the two right side engine mount insulator vertical fasteners and loosen the horizontal fastener. DO NOT remove the large nut in the center of the core of the insulator ( Fig. 4 ). 4. Remove the load on the engine mount by carefully supporting the engine with a floor jack. 5. Remove the vertical and horizontal fasteners from the engine side bracket. Remove the engine mount assembly. 6. Remove the idler pulley from the engine mounting bracket. ( Fig. 3 ). 7. Remove the engine mounting bracket. 8. Install a new engine mounting bracket. Torque the fasteners to 40-68 N.m (30-50 ft-lbs.). 9. Install the idler pulley to the engine mounting bracket. Torque the fastener to 40-68 N.m (30-50 ft-lbs.). 10. Properly route and position a serpentine belt onto all pulleys except the idler pulley (Use a new belt if there is any evidence of damage to the original one). 11. Rotate the belt tensioner clockwise until the belt can be installed onto the idler pulley. Slowly release the belt tensioner. 12. Install the engine mount; torque the assembly in the following order, engine mount to rail fasteners 68 N.m (50 ft-lbs.), vertical fastener 102 N.m (75 ft-lbs.), and horizontal fastener 150 N.m (111 ft-lbs.). 13. Install the purge duty cycle solenoid to the engine mount. 14. Start the vehicle and let it run for one minute then turn the engine off. 15. Verify the serpentine belt is properly aligned ( Fig. 1 ) 16. If the serpentine belt has moved toward the outboard edge of the idler pulley, further diagnosis will be required. WARRANTY INFORMATION POLICY: Reimbursable within the provisions of the warranty. LABOR OPERATION NO: 07-20-20-96 TIME ALLOWANCE: 0.7 Hrs. FAILURE CODE: P8 – New Par

2002 Land Rover Freelander (LN) Camshaft Timing Belt Service Repair

download
Service Repair No – 12.65.18 Remove 1. Disconnect battery earth lead. 2. Remove ancillary drive belt . 3. Remove RH front road wheel. 4. Remove 3 bolts securing RH splash shield to body and remove shield. 5. Remove 3 bolts securing camshaft timing belt LH rear cover and remove cover. 6. Rotate crankshaft in a clockwise direction and align the engine “SAFE” position, notch on crankshaft pulley aligned to the “ARROW” on front mounting plate and the timing marks aligned on the rear camshaft gears as illustrated 7. Remove bolt securing PAS pipe to engine front mounting plate. 8. Remove 3 Torx screws securing PAS pump pulley and remove pulley. Zoom Sized for Print Zoom Sized for Print Zoom Sized for Print 9. Remove 3 bolts securing PAS pump to front mounting plate and tie pump aside. 10. Release alternator battery lead terminal cover, loosen terminal nut and disconnect lead from terminal. 11. Disconnect multiplug from alternator. 12. Remove lower bolt and upper nut and bolt securing alternator to front mounting plate. 13. Remove alternator. 14. Remove Torx screw securing idler pulley to front mounting plate and remove pulley 15. Loosen bolt securing lower engine steady to front subframe. 16. Remove bolt securing lower engine steady to sump mounting, release lower engine steady from sump mounting. 17. Remove 3 bolts securing camshaft timing belt RH front cover and remove cover 18. Remove 3 bolts securing camshaft timing belt LH front cover and remove cover. 19. Assemble LRT-12-161 to LRT-12-199 and secure with clamp bolt. 20. Insert LRT-12-161 with LRT-12-199 into crankshaft pulley, loosen and remove pulley bolt. 21. Remove special tool from crankshaft pulley and remove crankshaft pulley. 22. Remove 3 bolts securing camshaft timing belt lower cover to cylinder block and remove cover. 23. Remove 2 bolts securing ancillary drive belt tensioner and remove tensioner. 24. Note fitted position of heat shield on A/C compressor and remove 3 bolts securing A/C compressor to front mounting plate and cylinder block. Release A/C compressor and heat shield and position aside. 25. Drain engine oil.

HONDA Front Seat Belt Replacement Warranty Policy

download
CUSTOMER INFORMATION : The information in this bulletin is intended for use only by skilled technicians who have the proper tools, equipment, and training to correctly and safely maintain your car. These procedures should not be attempted by “do-it-yourselfers,” and you should not assume this bulletin applies to your car, or that your car has the condition described. To determine whether this information applies, contact an authorized Honda automobile dealer. ? 1996 American Honda Motor Co., Inc. – All Rights Reserved . ATB 14788-17665 (9601) 1 of 2 JAN 22, 1996 92-012 BODY ALL 1986 and later Applicable To Model File U nder Issu e D ate Bulletin N o. Service Bulletin Front Seat Belt Replacement Warranty Policy (Supersedes 92-012, dated March 13, 1992) Warranty policy for front seat belt replacement is to replace either the belt/retractor mechanism or the buckle when either does not work properly. Warranty covers the replacement of the failed half of a belt, not the entire assembly (see PARTS INFORMATION ). NOTE: For 1970 through 1985 models, seat belts are replaced as a complete assembly under a separate warranty policy. COMPONENT REPLACEMENT Front seat belts are made by several suppliers, and some are sold as individual components (two separate halves); they are not stocked as a complete set. Therefore, whenever you replace a belt, make sure the new belt half is the same type and from the same manufacturer as the original – otherwise, the belt may not buckle properly. To determine the manufacturer and type (or “model”) of the belt, look for the white tag on the original belt in the car. The tag is on the retractor side of the belt (visible at the lower attachment point), or on the belt if you pull the belt all the way out. From the tag, mark down the manufacturer’s name (either Nippon Seiko K.K. or Takata), the belt “model” number and the date of manufacture. If the tag is missing or illegible, look on the buckle component for the name Nippon Seiko K.K. or the stylized “T” mark () for Takata. NOTE: Some belts may have NSK Warner K.K. as the manufacturer’s name. Use Nippon Seiko K.K. belts as the replacement. Take the information to your Parts Department to order the proper replacement belt. NOTE: For more information on seat belts and seat belt related items read: -Twisted Seat Belt (ServiceNews, July ’85) -Seat Belt Testing and Repair (Service Bulletin 86-014, August ’86) -Automatic Seat Belt Troubleshooting (ServiceNews, May ’89) -Lap Belt Retracts Slowly (Service Bulletins 90-003, January ’90 and 90-012, April ’90) -Torn Seal on Seat Belt Track (Service Bulletin 91-004, March ’91) -Slow to Retract Seat Belt, Cleaning the Guide Ring (ServiceNews, April ’91) -Accord Shoulder Belt System Wire Colors (ServiceNews, May ’91) -Seat Belt Slow to Retract (Service Bulletin 91-030, December ’91) Refer to your Service Bulletin Index and the ServiceNews Index for model specific information. Most repairs do not require seat belt component replacement. PARTS INFORMATION For front seat belt replacement ordering information and availability, contact your parts center.