shims for differential ird freelander

You search PDF repair manual about shims for differential ird freelander, if there are search results will appear below. If search results do not exist, please search by others keyword.



  shims for differential ird freelander Direct Download speed 5432 Kb/s

  shims for differential ird freelander Full Version speed 8172 Kb/s



2003 Ford F-Super Duty 250-550/ Excursion Differential Case and Ring Gear Removal And Installation manual

0

Filed Under (Ford Manuals) by admin on 07-02-2012

download
1. Remove the differential case. For additional information, refer to Differential Case in this section. 2. NOTE: The differential bearings need not be removed to overhaul the Ford limited slip differential. If bearing removal is required, for additional information, refer to Differential Case in this section. NOTE: The anti-lock speed sensor ring cannot be reused once removed. Remove the differential pinion shaft lock bolt and remove the differential pinion shaft. ? If required, remove the ring gear and anti-lock speed sensor ring. 3. NOTE: This tool does not have the 1/2-inch drive hole. Install the special tool in a suitable vise. 4. Install the differential case on the special tool 5. Install the special tool in the bottom side gear bore. ? Apply a small amount of grease to the centering hole of the special tool. 6. Install the nut in the upper differential side gear. Hold the nut in position while installing the hex screw. Tighten the hex-head screw until contact is made with the Step Plate 7. Insert a suitable dowel bar in the hole of the nut. Tighten the forcing screw to force the differential side gear away from the differential pinion gears. The dowel bar is used to keep the nut from turning when the forcing screw is tightened. 8. WARNING: Keep fingers/hands away from pinion gears when rotating the differential case with the differential rotating tool. NOTE: Differential pinion thrust washers cannot be removed independently of the differential pinion gears and so must be removed simultaneously with the differential pinion gears. Insert the special tool in the pinion shaft bore and turn the differential case to “walk” the differential pinion gears and differential pinion thrust washers out to the differential case windows. 9. Remove the differential pinion gears and differential pinion thrust washers. 10. Remove the differential side gears and differential clutch packs and tag them RIGHT and LEFT with the shim. CAUTION: When separating the clutch plates and clutch discs, note the sequence in which they are disassembled. They must be reassembled in the same sequence. CAUTION: Do not use acids or solvents when cleaning the differential clutch pack. Wipe components with a clean, lint-free cloth only. Separate the differential clutch discs and clutch plates for cleaning and inspection. Refer to the disassembled view of the limited slip differential case in the Description and Operation portion of this section.

Related Content:

2002 suburban front differential rebuild manual, 06 Z71 rear differential skematics, Rear differential dampener repair, rav4 differential, front differential fill plug 2004 buick rendezvous, 9 ford axle bearing installation diagram, differential unit disassembly procedure, buick rendezvous differential fluid, diassembly of differential unit, frontier rear diff position sensor

2003 Ford F-Super Duty 250-550/ Excursion Rear Drive Axle/Differential/ Ford 10.50-Inch Ring Gear Installation Manual

0

Filed Under (Ford Manuals) by admin on 30-06-2012

download
1. Remove the differential case. For additional information, refer to Differential Case in this section. 2. NOTE: The differential bearings need not be removed to overhaul the Ford limited slip differential. If bearing removal is required, for additional information, refer to Differential Case in this section. NOTE: The anti-lock speed sensor ring cannot be reused once removed. Remove the differential pinion shaft lock bolt and remove the differential pinion shaft. ? If required, remove the ring gear and anti-lock speed sensor ring. 3. NOTE: This tool does not have the 1/2-inch drive hole. Install the special tool in a suitable vise. 2003 F-Super Duty 250-550/Excursion Workshop Manual 5. Install the special tool in the bottom side gear bore. ? Apply a small amount of grease to the centering hole of the special tool. 6. Install the nut in the upper differential side gear. Hold the nut in position while installing the hex screw. Tighten the hex-head screw until contact is made with the Step Plat 2003 F-Super Duty 250-550/Excursion Workshop Manual 7. Insert a suitable dowel bar in the hole of the nut. Tighten the forcing screw to force the differential side gear away from the differential pinion gears. The dowel bar is used to keep the nut from turning when the forcing screw is tightened. NOTE: Differential pinion thrust washers cannot be removed independently of the differential pinion gears and so must be removed simultaneously with the differential pinion gears. Insert the special tool in the pinion shaft bore and turn the differential case to “walk” the differential pinion gears and differential pinion thrust washers out to the differential case windows. 9. Remove the differential pinion gears and differential pinion thrust washers. 10. Remove the differential side gears and differential clutch packs and tag them RIGHT and LEFT with the shim

Related Content:

ford e450 super duty manual, Sub Zero 550 Troubleshooting Guide, Ford 550 Backhoe Manual

TOYOTA 87/ 8 ” LANDCRUISER FULL FLOATING INSTALLATION MANUAL

0

Filed Under (Toyota Manuals) by admin on 20-03-2012

download
Removing the Existing Differential 5 2.1 Vehicle Support Safely secure the vehicle on a hoist. We recommend supporting the vehicle on a chassis hoist to keep the differential area at a convenient working height and to leave the wheels and axles free to be rotated and removed. Once supported off the ground, release the parking brake and leave the vehicle in neutral. Chock the wheels if necessary. 2.2 Differential Fluid Drain Clean around the differential drain plug to prevent dirt from entering the differential. Position a fluid drain reservoir under the differential and loosen the differential drain plug. Completely drain all differential fluid. HINT : This is a good time to check for metal particles in your oil and in the bottom of the housing which may indicate a worn bearing or differential component. 2.3 Removal of the Axles and Differential Remove the axles according to your vehicle’s service manual. HINT : When removing the axles try not to damage the paper gaskets behind the axle flanges. Disconnect the drive shaft from the flange of the differential. Remove the third member from the differential housing. Refer to your vehicle’s service manual. IMPORTANT : Collision damage or heavy off-road use of your vehicle in the past may have resulted in some degree of bending in the axle. Any misalignment of the axle tubes may result in excessive wear and/or failure of your differential and axle shafts. ARB strongly recommends that you have your axle assembly inspected for concentricity and straightness before installing your Air Locker 2 Removing the Existing Differential 6 2.4 Marking the Bearing Caps Using a small pointed center punch, gently mark the bearing caps in a way that will enable you to know which cap is ‘LEFT’ and which cap is ‘RIGHT’, which way is ‘UP’ and which way is ‘DOWN’. (Fig. 1. ) Mark the right hand cap in a similar way. HINT : Many installers choose to make one punch mark on the left hand side of the left hand bearing cap and a similar mark on the housing at close proximity to the cap mark. The right hand side is then designated with two punch marks on the right hand side of the cap and two similar punch marks on the housing

Related Content:

differential services pdf

1997-2001 HONDA CR-V (4WD) Noise From the Rear Differential REPAIR PROCEDURE

0

Filed Under (Honda Manuals) by admin on 06-01-2012

download
REPAIR PROCEDURE 1. Drain and refill the rear differential with Dual Pump Fluid. 2. Check the tires for proper inflation (recommended cold inflation front and rear is 26 psi) and any variation in tire size or type. 3. Test-drive the vehicle in a parking lot. Make tight, low-speed turns. If the noise is eliminated, return the vehicle to the customer. If the noise is still present, go to step 4. 4. Remove the rear differential assembly (see page 15-16 of the 1997-01 CR-V Service Manual). 5. Remove the torque control differential case, then remove and discard the 30 mm shim and the clutch assembly (see steps 1 thru 10 on pages 15-20 thru 15-22 of the service manual). 6. Remove the thrust needle bearing, the oil pump driveshaft, and the oil pump body assembly (see steps 11 and 12 on page 15-22 of the service manual). 7. Install the new flow collar over the drive pinion shaft. Make sure the tabs of the flow collar align with the oil pump pin. 8. For 1997 models: Assemble the new oil pump (spring, O-rings, piston, and pump body assembly). 9. Align the rear oil pump grooves with the oil pump pin and the flow collar tabs, then install the oil pump body assembly on the differential carrier. 10. Tighten the oil pump body assembly bolts to 12 N·m (8.7 lb-ft). 11. Align the oil pump driveshaft tabs with the grooves of the front oil pump in the oil pump body assembly, then install the oil pump driveshaft. 12. Install the thrust needle bearing with the outer race facing up.

Related Content:

differential service procedures, 2006 suburban oil pump replcement procedure, picture of 1997 4x4 honda passport axle warning lights, 1997 dodge ram 4x4 1500 service manual download, oil pump leak 2003 accord, oil pump on a 307, oil punp removal 2002 trailblazer, rav4 rear oil leak, Toyota 4 Y oil pump, what causes 147 transaxle code on 97 e420 mercedes

2002 Land Rover Freelander (LN) V6-2.5L Automatic Transmission/Transaxle Service and Repair Manual

0

Filed Under (Land Rover Manuals) by admin on 11-07-2012

download
Automatic Transmission/Transaxle: Service and Repair Gearbox – KV6 – NAS Models JATCO Gearbox – KV6 – NAS models Remove 1. Position the vehicle on a twin-post lift. 2. Tie bonnet back in upright position. 3. Disconnect battery earth lead. 4. Remove engine acoustic cover. 5. Release HO2S multiplug from support bracket on LH camshaft cover, disconnect multiplug. 6. Raise vehicle on lift. 7. Remove rear beam. 8. Remove RH catalytic converter 2002 Land Rover Freelander (LN) V6-2.5L Copyright © 2010, ALLDATA 10.20 Page 3 12. Remove bolt securing front pipe to bracket and remove front pipe. Discard gasket. 13. Remove 3 screws securing LH splash shield and remove shield 14. Release HO2S lead from clip on cylinder block. Remove 4 nuts securing exhaust manifold to cylinder head, remove manifold and discard gasket. 15. Drain fluid from IRD. 16. Drain gearbox fluid. 17. FitLRT-54-026 to the RH drive shaft inboard joint. 18. Using a suitable lever, release drive shaft from IRD. 19. With assistance, pull hub outwards and release drive shaft from IRD. CAUTION: Care must be taken not to damage oil seal when removing drive shaft from IRD. CAUTION: To avoid damage to gaiter or joint, do not allow shaft to hang on joint. 20. Remove LRT-54-026 from RH drive shaft inboard joint.

Related Content:

2002 land rover freelander 2 5 v6 head bolt torque specs, buick lacrosse glove compartment latch, kv6 rod bolts

HONDA CR-V Moan or Groan From the Rear Differential REPAIR PROCEDURE

0

Filed Under (Honda Manuals) by admin on 15-07-2012

download
REPAIR PROCEDURE: 2002-04 MODELS 1. Replace the rear differential fluid: •Refer to page 15-13 of the 2002-04 CR-V Service Manual , or •Online, enter keywords REAR DIFF, and select Rear Differential Fluid Inspection and Replacement (4WD) from the list. 2. Raise the vehicle on a lift until all four wheels are completely off the ground and can rotate freely. 3. Start the engine, and let it idle until the radiator fan cycles on and off twice. 4. Burnish the rear differential clutches: Automatic transmission models – •Set the parking brake, and shift the transmission to D. Let the engine idle for 5 minutes. •With the shift lever in D, release the parking brake, keep the wheel speed at 10 mph, and let all four wheels rotate freely for 5 minutes. •Apply the brakes to stop the wheels, repeat the bulleted steps one more time, then go to step 5. Manual transmission models – •With the engine idling and the parking brake released, shift the transmission into 1st, release the clutch, and let the wheels rotate for 5 minutes. •Disengage the clutch, and apply the brakes to stop the wheels. Shift the transmission into reverse, release the clutch, and let the wheels rotate for 5 minutes. •Shift the transmission into neutral, then apply the brakes to stop the wheels. •Repeat the bulleted steps one more time, then go to step 5. 5. Shift the transmission to P (A/T) or neutral (M/T), and turn off the engine. 6. Let the rear differential cool for 10 minutes

Related Content:

reset throttle in corolla, 1994 buick park ave how to bypass key vats, f-150 differential seal, fix gmc hatch release, fj cruiser transmission return line, ford cvt transmission maintenance schedule, how to change a thermostat in 2002 izuzu rodeo, how to change transmission fluid on 2005 trailblazer, hyundai accent 2002 vss wires, NPR Transmission Codes

1997-2005 Ford Expedition REAR AXLE NOISE REPAIR MANUAL

0

Filed Under (Ford Manuals) by admin on 16-09-2011

download
5L3Z-4209-F = (9.75-Inch Ring Gear/3.73 ratio) •205-506 – Seal Protectors (Rotunda Tool) (1997-2005 F-150, 1997-2005 •W710084-S439 – Wheel End Nuts Expedition/Navigator) •390266-S100 – Differential Slave Pin Bolt (9.75? axles) NOTE 9.75 REAR AXLE HOUSINGS WERE •387426-S100 – Differential Slave Pin Bolt (8.8? REDESIGNED IN MID-1999, INCREASING FRONT axles) PINION BEARING SIZE. REPLACING RING & •4B422 – Axle Circlips PINIONS IN AN OLD-STYLE AXLE ASSEMBLY •ZC-21 – Metal Surface Cleaner WILL REQUIRE INSTALLATION OF SPACER P/N •TA-29 – Ultra Silicone Sealant YL3Z-4662-CA. SPACER IS TO BE INSTALLED BETWEEN INNER PINION BEARING AND •TA-27 – Stud and Bearing Mount Retaining COLLAPSIBLE SPACER. Compound and Sealer •F3TZ-4121-AA – Fluid Tag (REQUIRED IF FLUID THE AXLE SERVICE KITS INCLUDE THE TYPE IS CHANGED FROM FEHP DURING FOLLOWING COMPONENTS: REPAIR) •4630 – Head Bearing WARRANTY STATUS: Eligible Under Provisions Of •4628 – Head Bearing Cup New Vehicle Limited •4676 – Pinion Seal Warranty Coverage •386989-S2 – Washer (Slinger) OPERATION DESCRIPTION TIME •4621 – Tail Bearing 052303A 1997-2002 Expedition, 4.7 Hrs. 1998-2002 Navigator, •4616 – Tail Bearing Cup 1997-2004 F-150 Heritage, •4222 – Differential Bearing Cups 2004-2005 F-150: Rear •4221 – Differential Bearings Axle Noise Repair •4209 – Gear Set (includes pinion shims, pinion (Includes Time For Road nut and crush spacer) Test To Verify Concern (Beam Axle)) (Do Not Use •4209 – Instruction Sheet With 4205A Or 4205A4) NOTE 052303A 2003-2005 Expedition: 5.8 Hrs. THE KIT DOES NOT INCLUDE THE FOLLOWING Rear Axle Noise Repair ITEMS. SOME OR ALL OF THESE ITEMS WILL (Includes Time For Road BE REQUIRED TO COMPLETE THE AXLE Test To Verify Concern (Irs SERVICE, DEPENDING ON AXLE Axle)) (Do Not Use With APPLICATION/STYLE. 4010D Or 4010D4) 052303A 2003-2005 5.9 Hrs. ORDER AS NEEDED:

Related Content:

2006 odyssey p0741 code, 2005 Scion TC Manual PDF, is there a fuse for speedometer on 2005 chevy tahoe, is the voltage regulator in the alternator or pcm in a 2005 hyundai santa fe, 2005 expedition repair manual, 2005 Ford Focus Workshop Manual Download, head suction drain adapter crownline 240ex, 2005 mercury mariner carrier bearing, ford e450 repair manual torrent, 2005 nissan maxima fuse box location

FORD 1983-1990 BRONCO II 1983-1995 RANGER 1991-1994 EXPLORER 4X4 system diagnosis can be difficult at times due to system complexities

0

Filed Under (Ford Manuals) by admin on 19-06-2011

download
HUBLOCK DIAGNOSTICS torque. As this torque attempts to turn the other axle shaft through the differential gears, that WHEEL END CONTAMINATION: shaft’s hublock will attempt to engage which will •All compact vehicle hublocks have an O-ring seal result in a ratcheting or buzzing noise. between the hublock and wheel hub to prevent •This type of noise concern is usually found on contamination. Whenever the hublock is removed, axles that have incorrect front axle differential the O-ring seal should be checked for damage. lubricant or very few 4X4 miles on them. •If contamination is found in the wheel end, the •Verify that the front axle differential lubricant is path must be determined and corrected. Path F1TZ-19580-A. If incorrect lubricant is detected, possibilities are through the hublock seal, the extract the old lubricant using a suction gun. wheel bearing seals or the axle spindle seals. NOTE BREAKING THE CARRIER SEAL IS NOT A RECOMMENDED METHOD OF EXTRACTING THE LUBRICANT. 1. Refill the front axle with 56 oz (1.66 L) of lubricant F1TZ-19580-A using a suction gun. 2. As the front axle accumulates 100-200 miles (161-322 km) of locked hublock operation, the axle will break-in, thus reducing the amount of differential motoring torque significantly. 3. If a front axle requires breaking in, refer to the Front Axle Break-In Procedure in this article

Related Content:

1994 ford ranger door latch installation instructions, how to remove spindle nut from 96 ford ranger

1986-1995 TOYOTA 4-5″ KIT FRONT INSTALLATION INSTRUCTIONS

0

Filed Under (Toyota Manuals) by admin on 14-05-2011

download
1. Chock the rear tires and lift the front of the truck with a floor jack. Place jack stands under the frame rails . Lower the vehicle on the jack stands. Never work under an unsupported vehicle. 2. Remove the tires and wheels. 3. Remove the stock shock absorbers using a 21 & 22 wrench. 4. Remove the brake caliper bolts from the knuckle using a 17mm wrench and secure out of way. Do not let the brake caliper hang by the brake line. Doing so could cause damage to the brake line. 5. Remove sway bar from the frame rail using a 12mm wrench and from the factory lower control arm using a 14mm wrench. See PHOTO 1 & 2 .Remove the front skid plate. (if equipped). 6. Remove the cotter pin on the tie rod and remove nut using a 19mm wrench. Strike the end of the knuckle to dislodge the tie rod. Retain the hardware for reuse 7. Remove the cotter pins from the upper and lower ball joint castle nuts and loosen the lower ball joint nuts using a 22mm wrench, but do not remove. Using a hammer, strike the knuckle as shown in PHOTO 3 & 4 to dislodge the ball joint on the upper and lower ball joints. PHOTO 1 PHOTO 2 8. Using a 17mm wrench remove the 6 nuts that secure the front half shaft to the differential. See PHOTO 5 . 9. Remove the tie rod mount from the knuckle by removing the two bolts as shown in PHOTO 6 .Using a 19mm wrench. 10. Remove the axle/knuckle assembly from the vehicle. PHOTO 3 PHOTO 4 PHOTO 5 PHOTO 6
11. Loosen and remove lower control arms using a 22mm & 24mm wrench as shown in PHOTO 7 & 8 . Retain the hardware for reuse. Remove the lower control arms from the vehicle. PHOTO 7 PHOTO 8 12. On the front cross-member, remove the 4 bolts securing the cross-member to the frame using a 17mm wrench as shown in PHOTO 9 . Retain hardware for reuse. 13. Remove the differential bolt as shown in PHOTO 10 using a 15mm wrench. Retain hardware for reuse. Remove the factory cross-member and retain for reuse. PHOTO 9 PHOTO 10 14. Remove driveshaft from the differential as shown in PHOTO 11 using a 13mm wrench. Retain hardware for reuse. Secure driveshaft out of harms way. PHOTO 12 15. Remove the two factory bump-stops from the frame using a 14mm wrench as shown in PHOTO 12 & 13. 16. Support the differential with a floor jack and remove the hardware on the drivers side as shown in PHOTO 14 using a 17mm wrench.

Related Content:

2000 tundra auto trans remove, front shocks 2009 toyota corolla, oem 27173 drive torque manual

2006 HONDA CIVIC Rear Brake Pad Inspection and Replacement Manual

0

Filed Under (Honda Manuals) by admin on 19-06-2012

download
Inspection 1. Raise the rear of the vehicle, and support it with safety stands in the proper locations. 2. Remove the rear wheels. 3. Check the thickness (A) of the inner pad (B) and the outer pad (C). Do not include the thickness of the backing plate. 4. If any part of the brake pad thickness is less than the service limit, replace the rear brake pads as a set. 5. Clean the mating surfaces between the brake disc and the inside of the wheel, then install the rear wheels Replacement 1. Remove some brake fluid from the master cylinder. 2. Raise the rear of the vehicle, and support it with safety stands in the proper locations. 3. Remove the rear wheels. 4. Remove the brake hose mounting bolt (A). 5. Remove the flange bolts (B) while holding respective caliper pin (C) with a wrench. Be careful not to damage the pin boot, and remove the caliper (D). Check the hose and pin boots for damage and deterioration. NOTE: Do not twist the brake hose and the parking brake cable to prevent damage. 6. Remove the pad shims (A) and the brake pads (B). 7. Remove the pad retainers (A). 8. Clean the caliper bracket (B) thoroughly; remove any rust, and check for grooves and cracks. Verify that the caliper pins (C) move in and out smoothly. Clean and lube if needed. 9. Inspect the brake disc for runout, thickness, parallelism and check for damage and cracks. 10. Apply a thin coat of M-77 assembly paste (P/N 08798-9010) to the retainer mating surface of the caliper bracket (indicated by the arrows). 11. Install the pad retainers. Wipe excess assembly paste off the retainers. Keep the assembly paste off the brake disc and brake pads. 12. Apply a thin coat of M-77 assembly paste (P/N 08798-9010) to the pad side of the shims (A), the back of the brake pads (B), and the other areas indicated by the arrows. Wipe excess assembly paste off the pad shims and the brake pads friction material. Keep grease and assembly paste off the brake disc and the brake pads. Contaminated brake disc or brake pads reduce stopping ability. 13. Install the brake pads and the pad shims correctly. Install the brake pad with the wear indicator (C) on the bottom inside. If you are reusing the brake pads, always reinstall the brake pads in their original positions to prevent a momentary loss of braking efficiency

Related Content:

2002 suburban front differential rebuild manual, 06 Z71 rear differential skematics, Rear differential dampener repair, rav4 differential, front differential fill plug 2004 buick rendezvous, 9 ford axle bearing installation diagram, differential unit disassembly procedure, buick rendezvous differential fluid, diassembly of differential unit, frontier rear diff position sensor