sienna rear axle noise

You search PDF repair manual about sienna rear axle noise, if there are search results will appear below. If search results do not exist, please search by others keyword.



  sienna rear axle noise Direct Download speed 5432 Kb/s

  sienna rear axle noise Full Version speed 8172 Kb/s



1997 Jeep Grand Cherokee Laredo 7 1/8″, 7 1/3″, 7 9/16″, 7 4/5″, 8 1/4″, 8 1/2″ & 8 9/10″ Ring Gears Removal And Installation Manual

0

Filed Under (Jeep Manuals) by admin on 04-07-2012

download
Removal (Model 194, 8 1/4″ & 1998 Grand Cherokee 216 Axles) 1. Raise and support vehicle. Remove rear wheel(s). If equipped with drum brakes, remove brake drum. If equipped with disc brakes, remove brake caliper and rotor. On all models, clean axle housing cover. Loosen cover bolts, and drain oil. Remove cover. 2. Remove differential pinion-shaft lock bolt. Remove pinion shaft from differential. Push in axle. Remove “C” clip from axle at pinion gear. Remove axle from tube. Remove axle shaft seal and bearing from axle tube. Installation 1. Grease bearing, and install into axle tube. Ensure bearing part number is facing outwards. Apply wheel bearing grease to axle shaft seal. Install seal in axle tube. Install axle shaft. 2. Install axle “C” clip. Pull axle out to seat “C” clip. Install pinion shaft. Install lock bolt, and tighten to specification. Apply RTV to axle housing cover. Tighten cover bolts to specification. See TORQUE SPECIFICATIONS table. Fill with gear oil. Removal (Model 198, 1999 Grand Cherokee 216 & 226 Axles) 1. Raise and support vehicle. Remove rear wheel(s). Remove brake drum. Remove nuts securing axle retainer plate to axle tube, and discard. Using slide hammer and Adapter (6790), remove axle shaft from axle tube. 2. Using a 3/8″ drill bit, drill a shallow hole into bearing retaining ring on axle. DO NOT drill into axle. Using a cold chisel, cut bearing retaining ring across drilled hole, and remove from axle shaft. Using a press and Bearing Remover (1130), remove bearing from axle shaft. Remove seal and retainer plate from axle shaft. Installation 1. Ensure axle shaft retaining plate is flat and not warped. Install retaining plate on axle shaft. Apply wheel bearing grease to axle shaft seal. Install seal on axle shaft. Grease bearing, and install on axle shaft with outer surface groove facing seal. 2. Using press and Bearing Installer (7913), press bearing onto axle shaft. Press NEW bearing retainer ring onto axle shaft. Install axle shaft in axle tube. Tighten NEW axle retainer plate nuts to specification. See TORQUE SPECIFICATIONS table. PINION SEAL & YOKE Removal

Related Content:

2005 chevy silverauto right front wheel bearing hub bearing nut tork setting, exploded view 1996 jeep grand cherokee exploded view of front suspension, Meritor Axle Nut Torque Specs, Silverado Rear Axle Seal Replacement, how to remove right front axle 95 bronco, saturn sl hub bolt torque, DIY LEXUS GX 470 AXLE REPLACE, how to remove axle seal in a 1999 chevy malibu, size axle nut 2005 explorer, 2002 ford expedition trailing arm torque specs

2007 HONDA ODYSSEY SPLASH GUARDS INSTALLATION INSTRUCTIONS

0

Filed Under (Honda Manuals) by admin on 14-10-2011

download
INSTALLATION NOTE: •These instructions show the left splash guards being installed. The same procedure applies to installing the right splash guards. •Clean and wax the areas to be covered with a high-quality paste wax. Installing the Front Splash Guards 1. Turn the steering wheel all the way counter clockwise to provide access to the left front fenderwell. 2. Remove the two self-tapping screws from the left front inner fender. PARTS LIST Right front splash guard Left front splash guard Right rear splash guard Left rear splash guard 6 Self-tapping screws 2 Spring nuts 2 Square head grommets 3. Using a pushpin, make a small hole through the center of the upper clip. UPPER CLIP PUSHPIN SELF-TAPPING SCREW LEFT FRONT INNER FENDER SPLASH GUARDS P/N 08P00-SHJ-101 2 of 2 All 33039-33598 (0608) LEFT REAR SPLASH GUARD SELF-TAPPING SCREW LEFT REAR FENDERWALL SELF- TAPPING SCREW (reused) REAR BUMPER LEFT REAR SPLASH GUARD There must be no clearance. REAR BUMPER LEFT FRONT INNER FENDER LEFT FRONT SPLASH GUARD LEFT FRONT INNER FENDER SELF- TAPPING SCREW LEFT FRONT SPLASH GUARD CLIP CLIP SELF- TAPPING SCREW SELF-TAPPING SCREW (reused) LOWER HOLE 5. While holding the left splash guard against the fender, tighten the self-tapping screws in the order shown. 6. Turn the steering wheel all the way clock wise and repeat steps 2 through 4 to install the right front splash guard. Installing the Rear Splash Guard 7. Using a floor jack, lift up the left rear side of the vehicle according to the service manual. 8. Remove the self-tapping screw from the rear bumper. Using a pushpin, make a hole through the center of the recess. 9. Install one square head grommet into the hole in the left rear fenderwall. Slide one spring nut over the hole you made in step 8 in the rear bumper. 10. Position the left rear splash guard on the left rear fenderwall and rear bumper, and loosely install one self-tapping screw you removed, and the two self-tapping screws supplied with the kit. LEFT REAR FENDERWALL REAR BUMPER SELF-TAPPING SCREW (Reuse.) SQUARE HEAD GROMMET SPRING NUT RECESS PUSHPIN REAR BUMPER With RECESS SELF- TAPPING SCREW 4. Install the left front splash guard using the two self-tapping screws removed in step 2, and one self-tapping screw supplied with the kit. Do not tighten the self-tapping screws yet. 11. Hold the left rear splash guard against the fenderwall and check that there is no clearance between the splash guard and rear bumper. Tighten the three self-tapping screws in the sequence shown. 12. Repeat steps 7 thru 11 to install the right rear splash guard

Related Content:

yhs-fullyhosted_003, how do you replace liftgate relay for 2005 escalade, rear hub assembly removal for 2008 toyota tundra, ruff and tuff golf cart parts rear axle bearing, installation instructions for a 2007 honda accord front bumper, Rear brakes 2000 Jag xj8 procedure, rear ac lines on 05 chevy trailblazer, lincoln ls rear suspension squeak, liftgate actuator replacement tahoe, left cowl ground

FORD F450/ 550 SUPER DUTY CHASSIS CABS OWNERS MANUAL

0

Filed Under (Ford Manuals) by admin on 21-05-2012

download
LATERAL CONTROL ROD AXLE BRACKET INSTALLATION 1. Remove and discard the OEM shock absorbers, but retain the mounting fasteners (bolts & nuts) for re-use. 2. Remove the top d-bushing mount bolts and disconnect the axle breather tube (See Figure 2- 1). 3. If the truck is equipped with an S110 4.25″ X 4.25″ square axle (most F450s and F550s), install both axle spacer tabs on the axle bracket using (4) 1/2 x 1 1/4 UNC FLANGE BOLTS and (4) UNC TOP LOCK FLANGE NUTS. (See Figure 2-2). 4. Loosely fasten the axle bracket to the axle as shown in Figure 2-3 using (2) M12 x 1.75 x 40 METRIC BOLTS and (2) 1/2″ WASHERS. 5. Reconnect the axle breather tube to the axle. LATERAL CONTROL ROD (LCR) FRAME BRACKET INSTALLATION 1. On the PASSENGER side, remove to two top rivets from the OE bumper bracket and ream the holes to 0.47″ (See Figure 3-1) 2. Install the frame bracket as shown in Figure 3-2 using (4) 7/16 UNC TOP LOCK FLANGE NUTS. FIG. 3-2 Frame bracket Remove these two rivets and ream to 0.47″ DRIVER SIDE DISASSEMBLY 1. With weight taken off the rear springs, as noted in pre-installation checklist, remove the rear leaf spring hanger. Removal of the rear overload spring bracket is optional See Figure 4-1. 2. Remove the front spring hanger bracket and the front overload spring bracket. (See Figure 4-2). 3. Remove existing U-bolts that attach the axle to the leaf spring and keep the OE U-bolt plate for later use. (See Figure 4-3) After this is done, the axle, spring, and hanger will be loose. Remove and discard the spring and hangers from the axle.DRIVER SIDE ASSEMBLY 1. Review Figure 5-1 & Figure 13-2 to acquaint yourself with the various parts of the UltraRide suspension. 2. Fasten the Front Hanger to the frame using (6) 9/16 x 1-1/2 UNF BOLTS, (6) 9/16 UNF NUTS, and (12) 9/16 FLAT WASHERS. Route the parking brake cables through the corresponding holes on the Front Hanger. 3. Assemble the Suspension Arm to the axle using (2) M20 X 2.50, 79 X 425 METRIC U- BOLTS, (4) M20X2.5 METRIC NUTS, and original OE top plate and axle bracket. Make sure the arm/axle locating pin is properly inserted into the mating hole on the axle pad and that the bottom side of the arm rests evenly on the axle pad. 4. Insert the Bolt Spacer Tube into the arm bushing and loosely fasten the arm to the front hanger using (1) 3/4 X 7 UNF BOLT, (1) 3/4 UNF NUT, (2) 3/4 WASHERS, and (2) plastic wear washers. 5. Loosely fasten the Lateral Control Rod Axle Bracket to the Arm using (2) 1/2 X 1-1/4 UNC FLANGE BOLTS (See Figure 5-2). 6. Bolt the Air Spring Bracket Assembly to the frame using (5) 1/2 X 1-1/4 UNC FLANGE BOLTS and (5) 1/2 UNC TOP LOCK FLANGE NUTS. One frame hole will need to be reamed to 0.53″ on each side. See Figure 5-2. 7. Bolt the Air Spring to the Suspension Arm using (1) 1/2 UNC JAM NUT. Make certain the air spring is not twisted or creased after tightening the nut.

1991 Infiniti G20 AXLE SHAFTS – FRONT REMOVAL AND INSTALLATION MANUAL

0

Filed Under (Infiniti Manuals) by admin on 13-02-2012

download
REMOVAL & INSTALLATION FWD AXLE SHAFT Removal (Axle Shaft) 1. Raise and support vehicle. Remove front wheel assembly. Remove wheel bearing lock nut. Remove brake caliper, and support aside. Remove brake rotor. 2. Disconnect tie rod end. Remove upper knuckle nut, and separate knuckle assembly from third link assembly. Push axle shaft through hub, and separate axle assembly from knuckle assembly. 3. Insert screwdriver blade between transaxle case and right axle inner CV joint. Pry out on joint until joint pops free. Use care not to damage axle boot or axle seal. 4. On M/T vehicles, remove left axle in same manner. On A/T vehicles, insert screwdriver through differential, and drive axle out of transaxle case using a hammer. See Fig. 2 . PROBLEM Possible Cause/Action GREASE LEAKING Ripped CV Boot Replace Boot CLICKING NOISE WHILE CORNERING Dry/Worn CV Joints Replace Outer CV Joints CLUNK ON ACCELERATION Dry/Worn CV Joints Replace Inner CV Joints Worn Transmission Gears/Bearings Inspect Transmission VIBRATION/SHUDDER ON ACCELERATION Dry/Worn CV Joints Replace CV Joints Alignment Out Check Alignment Incorrect Spring Height Check Spring Height SQUEALING OR HUMMING Dry/Worn CV Joints Lube/Replace CV Joints Faulty Wheel Bearing Replace Wheel Bearing NOTE: DO NOT allow brake caliper to hang from brake hose. CAUTION: Use care not to damage pinion mate shaft or side gear while driving out axle. 1991 Infiniti G20 AXLE SHAFTS – FRONT’ ’1991-92 DRIVE AXLES FWD Axle Shafts None Page 2
Fig. 2: Removing Left Drive Axle (A/T Vehicles) Courtesy of NISSAN MOTOR CO., U.S.A. Removal (Outer CV Joint) 1. Remove and discard boot bands. Slide boot off joint housing. Thread wheel bearing lock nut onto joint. Using a slide hammer and bearing puller, remove joint from axle shaft. See Fig. 3 . NOTE: Outer joint cannot be disassembled. Remove and inspect joint and replace if damaged or worn. 1991 Infiniti G20 AXLE SHAFTS – FRONT’ ’1991-92 DRIVE AXLES FWD Axle Shafts None Page 3 2. Remove circlip from end of axle, and remove boot. If boot is being reused, take care not to cut boot on axle splines during removal. Clean CV joint in suitable solvent. Inspect components, and replace joint if necessary.

Related Content:

1991 ford ranger manual, shopmanuel for 1991 chevy cavalier, car manual for 1991 lexus ls400, how do i remove cv shaft on 1996 infiniti g20, snap and pop from axel when cornering in silverado, transaxle play in Nissan sentra

1979-1985 Toyota Pick-Up 4WD Superlift 7″ Lift System for INSTALLATION INSTRUCTIONS

0

Filed Under (Toyota Manuals) by admin on 24-03-2012

download
INSTALLATION PROCEDURE 1) FRONT OF VEHICLE… â Put the transmission in neutral. Position a floor jack under the front axle and raise vehicle. Place jack stands under the frame rails a few inches behind the spring’s rear shackles. Ease the jack down until the frame is resting in the stands. Keep a slight load on the jack. Put the vehicle in gear or park, set emergency brake and chock rear wheels to prevent any possibility of movement. ââ Remove tires and shocks. Remove the engine belly-pan to gain access to the anti-sway bar. Remove and discard the anti-sway bar assembly. Our spring/shock rate and the bars design render it useless. Reinstall belly-pan. ââ Detach the flexible rubber brake hoses at the calipers only and pinch closed with vise-grips to prevent fluid loss. SEE SEPERATE INSTRUCTIONS. You will install the Superlift hoses later. â Remove the stock drag-link. SEE SEPERATE INSTRUCTIONS. You will install the Superlift link and steering arm later. FORM #7047 .01-080707 PRINTED IN U.S.A. PAGE 2 OF 5 â Remove the bolt attaching the trac-bar (or torque rod) to its bracket on the drivers side of the axle. Unbolt the driveshaft at the front axle and tie it up and out of the way. ââ Remove the spring U-bolts. Ease down the front axle by lowering the jack. The axle vent hose may need rerouting of replacing. Install the Polyurethane bushings into the spring eyes. Lubricate all bushing wear surfaces with light grease. ââ Install the Superlift springs so that the thick end of the degree shims, attached to the bottom of the spring, are pointing towards the front of the vehicle. NOTE: There is a driver (DR) and passenger (PA) side spring. Start, but do not tighten the spring hanger/shackle bolts. ââ Raise the axle up to the springs. Be sure the spring center bolt heads seat properly in the axle perch holes. Attach with the new furnished U-bolts and evenly torque to 131ft. lbs. â Install the superlift Trac-Bar Bracket. â Install the Superlift steering Arm and Adjustable Drag- Link. ââ Install the front Superlift Extended Length Brake Hoses. ââ Install shocks, tires and lower vehicle. ââ With the vehicle weight on the suspension, tighten the front and rear spring hanger bolts. Do not over tighten; tighten only until the bushing flanges compress slightly. 2) REAR OF VEHICLE… NOTE: Before starting, with the vehicle weight on the suspension, rotate the position of the brake proportioning rod where it goes into the proportioning valve; which is located on the passenger side frame rail. On most vehicles, the rod is pretty much horizontal at the attaching point. After the lift is installed, re-bend the rod to its stock position at the proportioning valve. ââ Place a floor jack under the rear axle and raise vehicle. Place jack stands under the frame rails, a few inches in front of the rear springs front hangers. Ease the jack down until the frame is resting on the stands. Keep a slight load on the jack. Chock the front wheels to prevent any possibility of movement. Remove tires, U-bolts and shocks. ââ Disconnect the emergency brake cables at the rear wheels. Lower the axle housing by easing down the jack. Do not overextend the brake and axle vent hoses; both may need rerouting or replacing. If a Superlift rear hose is to be installed detach the stock rubber hose at the axle housing only and pinch closed with vise-grips to prevent fluid loss. You will install the new hose after installing the other rear components

Related Content:

2005 Toyota Avalon Rear Suspension Assembly no 2, wher to place jack stands on 2012 town and country

TOYOTA LANDCRUISER INSTALLATION INSTRUCTIONS

0

Filed Under (Toyota Manuals) by admin on 10-11-2011

download
INSTALLATION INSTRUCTIONS 1. Park the vehicle on a level surface. Check the vehicle height from side to side and front to back. This is done by measuring from the ground up to the fender using the hub as a centering point. 2. Apply a thin coat of grease to the polyurethane bushings and insert into each eye of the new front springs. Now apply a thin coat of grease on outside of bushings. This will help you to insert the bushing into the spring mount. 3. Raise the front of the vehicle and support securely with jack stands under the frame behind the front springs, and block the rear wheels. Remove the tires, shocks, u-bolts, and loosen the sway bar bolts. (Caution: the front axle will now be free to move, so support securely on floor jack.) 4. With a floor jack supporting the axle, unbolt each end of leaf springs and remove from both sides. (If new shackle bushings were purchased, grease and install them in the frame at this time.) Install new front springs, part # 8041. When installing the front springs that the fat part of the shim on the bottom of the spring pack should be pointing toward the rear of the vehicle. Notice the tie bolt in the front leaf springs is not in the center of the leaf spring, but there is a long end and short end. Install the springs with the short end towards the rear, and long end towards the front bumper. Do not tighten spring eyebolts at this time. 92756702 64-80 TOYOTA LANDCRUISER INSTALLATION
INSTRUCTION SHEET Technical Assistance – (731) 285-9000 Page 2 5. Using the floor jack, lower the front axle down to the leaf springs. Be sure the tie bolts align and fit into the tie bolt holes in the front axle housing. Install and tighten new u-bolts. Torque u-bolts to 75-90 ft.lbs. 6. Install new shocks and tires then lower the vehicle to the ground. Tighten spring eyebolts at this time. NOTE: The drag link that goes along side of the frame from the gear box to the bell crank may require slight bending for clearance of the new shock. Bending this drag link will not affect it, but do not kink the bar. 7. Raise the rear of the vehicle. Support securely with jack stands and block the front wheels. Remove the tires, shocks, and u-bolts. (CAUTION: the rear axle will be free to move, so support securely on a floor jack. 8. Apply a thin coat of grease to the polyurethane bushings and insert into each eye of the new rear springs. Now apply a thin coat of grease on outside of bushings. This will help you to insert the bushing into the spring mount. 9. With a floor jack supporting the rear axle, unbolt each end of the rear leaf spring and remove from both sides. (If new shackle bushings were purchased, grease and install them in the frame at this time.) Install new springs, part # 8042. When installing the rear springs the fat part of the shim on the bottom of the spring pack should be pointing toward the front of the vehicle. Notice the tie bolt in the rear leaf springs is not in the center of the leaf springs, but there is a long end and a short end. Install the springs with the short end towards the front and longer end towards the rear bumper. Do not tighten spring eyebolts at this time. 10. Using a floor jack, lower the rear axle down to the leaf springs. Be sure tie bolts align and fit into the tie bolt holes in the axle housing. Install and tighten new u-bolts, shocks and tires then lower vehicle to the ground. Torque u-bolts to 75-90 ft.lbs. Tighten spring eyebolts at this time.

Related Content:

ford 8 8 rear end rebuild, tahoe balance bar repair, 04 ford f150 8 8 rear end rebulid, replacing a 1997 ford thunderbird rear end, rear for equinox 2005 bolt kit, Meritor Rear Axle Parts Breakdown, how to disassemble 8 inch ford rear axles, grease maintenance for 1997 ford f350, GM 14 BOLT REAREND MANUAL, ford 9 75 rear end specs

1997-2005 Ford Expedition REAR AXLE NOISE REPAIR MANUAL

0

Filed Under (Ford Manuals) by admin on 16-09-2011

download
5L3Z-4209-F = (9.75-Inch Ring Gear/3.73 ratio) •205-506 – Seal Protectors (Rotunda Tool) (1997-2005 F-150, 1997-2005 •W710084-S439 – Wheel End Nuts Expedition/Navigator) •390266-S100 – Differential Slave Pin Bolt (9.75? axles) NOTE 9.75 REAR AXLE HOUSINGS WERE •387426-S100 – Differential Slave Pin Bolt (8.8? REDESIGNED IN MID-1999, INCREASING FRONT axles) PINION BEARING SIZE. REPLACING RING & •4B422 – Axle Circlips PINIONS IN AN OLD-STYLE AXLE ASSEMBLY •ZC-21 – Metal Surface Cleaner WILL REQUIRE INSTALLATION OF SPACER P/N •TA-29 – Ultra Silicone Sealant YL3Z-4662-CA. SPACER IS TO BE INSTALLED BETWEEN INNER PINION BEARING AND •TA-27 – Stud and Bearing Mount Retaining COLLAPSIBLE SPACER. Compound and Sealer •F3TZ-4121-AA – Fluid Tag (REQUIRED IF FLUID THE AXLE SERVICE KITS INCLUDE THE TYPE IS CHANGED FROM FEHP DURING FOLLOWING COMPONENTS: REPAIR) •4630 – Head Bearing WARRANTY STATUS: Eligible Under Provisions Of •4628 – Head Bearing Cup New Vehicle Limited •4676 – Pinion Seal Warranty Coverage •386989-S2 – Washer (Slinger) OPERATION DESCRIPTION TIME •4621 – Tail Bearing 052303A 1997-2002 Expedition, 4.7 Hrs. 1998-2002 Navigator, •4616 – Tail Bearing Cup 1997-2004 F-150 Heritage, •4222 – Differential Bearing Cups 2004-2005 F-150: Rear •4221 – Differential Bearings Axle Noise Repair •4209 – Gear Set (includes pinion shims, pinion (Includes Time For Road nut and crush spacer) Test To Verify Concern (Beam Axle)) (Do Not Use •4209 – Instruction Sheet With 4205A Or 4205A4) NOTE 052303A 2003-2005 Expedition: 5.8 Hrs. THE KIT DOES NOT INCLUDE THE FOLLOWING Rear Axle Noise Repair ITEMS. SOME OR ALL OF THESE ITEMS WILL (Includes Time For Road BE REQUIRED TO COMPLETE THE AXLE Test To Verify Concern (Irs SERVICE, DEPENDING ON AXLE Axle)) (Do Not Use With APPLICATION/STYLE. 4010D Or 4010D4) 052303A 2003-2005 5.9 Hrs. ORDER AS NEEDED:

Related Content:

2005 Scion TC Manual PDF, 2006 odyssey p0741 code, head suction drain adapter crownline 240ex, 2005 nissan maxima fuse box location, is the voltage regulator in the alternator or pcm in a 2005 hyundai santa fe, 2004 LINCOLN AVIATOR TRUCK SUV Service Shop Repair Manual pdf, 2005 Toyota Scion TC Manual, is there a fuse for speedometer on 2005 chevy tahoe, 2005 mercury mariner carrier bearing, 1997 ford ranger repair manual pdf

2005-2009 V6 Ford Mustang dual exhaust system with Power-X crossover Installation Manual

0

Filed Under (Ford Manuals) by admin on 08-12-2011

download
Installation instructions: 1.) Raise and support vehicle. 2.) Remove stock muffler from vehicle by un-bolting hangers from frame, loosening inlet clamp, and lowering unit out from under vehicle with hangers still attached to muffler. 3.) Loosen clamp attaching factory over-axle pipe to vehicle Y-pipe and remove over-axle pipe from vehicle. 4.) Use a reciprocating saw and cut both legs of the factory Y-pipe even with the rear surface of the transmission cross-member as indicated in the photo 1 on the next page; remove the cut-off portion from vehicle and discard. 5.) Place on supplied 2.25?clamp onto the left inlet of the crossover assembly and insert the supplied left inlet pipe. 6.) Place on supplied 2.25?clamp onto the right inlet of the crossover assembly and insert the supplied right inlet pipe. 7.) Place two supplied 2.25? clamps onto the inlet pipes and install the entire crossover assembly onto the cut ends of the vehicle converter pipes. 8.) Place one supplied 2.25?onto the left over-axle pipe and install the pipe onto the left outlet of the crossover assembly. When properly installed, the pipe will be routed over the rear axle and terminate above the pan-hard brace on left side of vehicle; refer to photo 2 on next page 9.) Place one supplied 2.25?onto the right over-axle pipe and install the pipe onto the right outlet of the crossover assembly. When properly installed, the pipe will be routed over the rear axle and terminate above the pan- hard brace on right side of vehicle; refer to photo 2 on next page. 10.) Remove factory rubber hangers from stock muffler, noting their correct orientation, and transfer them onto the hanger rods attached to right side muffler. 11.) Place one supplied 2.25?clamp onto inlet of right side muffler and install entire assembly onto the outlet of the right side over-axle pipe previously installed. 12.) If you are installing this system with a stock rear valance/bumper, make a template of the right side tip relief(Or use the template on the supplement sheet included) and attach it to the left side of bumper in the approximate equal position to vehicle centerline. Use a small pneumatic recriprocating saw to cut the bumper along the traced lines from the template. Use care and patience to cut a precise hole. 13.) The driver side muffler is to be attached with supplied fabricated hangers and 5/16 bolts. You must first cut threads in four existing holes in left side frame with a 5/16-18 tap. These holes can be identified visually, as they have extra material thickness inside the holes compared to other holes in the frame. Refer to photos 3 and 4 below to determine the intended location and orientation of the left side brackets. 14.) “Test” install the left muffler onto the car and check the bumper relief alignment to the center of the tip. Perform any additional clearance work around the tip at this time, if needed. 15.) Place a supplied 2.25?clamp over inlet of the left side muffler and install onto outlet of left side over-axle pipe. Attach muffler hangers to frame with supplied 5/16 bolts. Do not fully tighten clamp at this time

Related Content:

replacing flex pipe on 2005 Tuarus, ford escape Exhaust Flex Pipe Repair Kits, ford escape flex pipe repair kit, repair cost on a flex pipe ford escape

2007 Toyota Camry Rear Bumper Removal and Replacement Manual

0

Filed Under (Toyota Manuals) by admin on 26-01-2012

download
REMOVAL 1. REMOVE REAR BUMPER ASSEMBLY (w/o Rear Lower Spoiler ) a. Put protective tape around the rear bumper assembly. b. Using a screwdriver, open the 2 rear bumper plates. HINT: Tape the screwdriver tip before use. c. Remove the 6 screws and 2 clips. d. Disengage the 12 claws and disconnect the rear bumper assembly as shown in the illustration HINT: Use the same procedures for the RH side and LH side. e. Remove the rear bumper assembly. 2. REMOVE REAR FLOOR BOARD (w/ Rear Lower Spoiler ) a. Remove the 4 screws, 2 clips, 3 nuts and rear floor board. 3. REMOVE REAR BUMPER ASSEMBLY (w/Rear Lower Spoiler ) a. Put protective tape around the rear bumper assembly. b. Using a screwdriver, open the 2 rear bumper plates. HINT: Tape the screwdriver tip before use. c. Remove the 6 screws. d. Disengage the 12 claws and disconnect the rear bumper assembly as shown in the illustration. HINT: Use the same procedures for the RH side and LH side. e. Remove the rear bumper assembly. INSTALLATION 1. INSTALL REAR BUMPER ASSEMBLY (w/o Rear Lower Spoiler ) a. Engage each claw.

Related Content:

2005 F250 Ford Truck rear brake backing plate, how to remove rear bumper 2008 camry, time it takes to repair front bumper for 2007 toyota camry

2009 Ford Escape 3.0L INTERMITTENT CYLINDER HEAD CAMSHAFT KNOCK/ THUMP NOISE SERVICE PROCEDURE

0

Filed Under (Ford Manuals) by admin on 25-01-2012

download
3.0L INTERMITTENT CYLINDER HEAD CAMSHAFT KNOCK/THUMP NOISE This article supersedes TSB 09-11-6 to update the b. Isolate noise to LH – Listen to the cylinders Service Procedure and Part List. 4 and 6 valve cover fasteners (number 6 is by the coolant pump). There will be a ISSUE significant difference in transmitted noise Some 2009 Escape and Mariner vehicles, equipped between the cylinder 4 and 6 fasteners with 3.0L engine, may exhibit an intermittent when noise is present. Noise from LH – go knocking or thumping type noise from the cylinder to Step 4. head. After engine temperature reaches 210-220 °F NOTE (99-104 °C), the noise is typically heard from the THE RH AND LH NOISES HAVE DIFFERENT rear of the engine as the vehicle comes to a stop. CAUSES. FOLLOW ALL STEPS CAREFULLY FOR An example would be coming to a stop at the end PROPER DIAGNOSIS AND REPAIR. of a highway exit ramp. Noise will continue 45-60 seconds and then diminish. Noise will occur again 3. Replace the RH cylinder head per Workshop once engine reaches 210-220 °F (99-104 °C) and Manual (WSM), Section 303-01B. vehicle comes to another stop. a. Verify repair by repeating Step 2. If noise is ACTION still present then proceed with normal Follow the Service Procedure steps to correct the engine NVH diagnostics per WSM, Section condition. 100-04. SERVICE PROCEDURE 4. Remove LH valve cover. Refer to WSM, Section 303-01. 1. Is noise a 45-60 second knock/thump from a hot engine as the vehicle comes to a stop? a. Rotate the engine clockwise until cylinder number 6 exhaust cam lobes are pointing a. Yes – Go to Step 2. up and valves are fully closed. Exhaust camshaft needs to be left in this position for b. No – Stop as this procedure does not apply. all bearing caps in Step 4b. (Figure 1) Proceed with normal Workshop Manual (WSM), Section 100-04 diagnostics. 2. Using Chassis Ears, isolate the noise to Right Hand (RH) (Bank 1) or Left Hand (LH) (Bank 2) cylinder head. Noise is typically heard as 45-60 second knock/thump as the vehicle comes to a stop after engine reaches 210-220 °F (99-104 °C). a. Isolate noise to RH – Listen to the cylinder head by the variable camshaft timing (VCT) solenoid connectors. There will also be a vibration felt at the VCT solenoid connector when noise is present. Noise from RH – go to Step 3.

Related Content:

02 kia rio 1 5 will idle no accelaration, 2013 f-150 click noise at stop and start, causes of ford escape 2001 engine vibration, 2005 tundra tailgate noisey, ticking noise and misfire 4 8 litre gmc, chevy silverado catalytic converter 2004 v6 knocking tapping noise, Ford Escape motor mount removal and installation how to, GMC noise when brakes applied or released, how do i change the VCT solenoids on 2009 ford escape, installing engine in a 2008 ford escape

Related Content:

2005 chevy silverauto right front wheel bearing hub bearing nut tork setting, exploded view 1996 jeep grand cherokee exploded view of front suspension, Meritor Axle Nut Torque Specs, Silverado Rear Axle Seal Replacement, how to remove right front axle 95 bronco, saturn sl hub bolt torque, DIY LEXUS GX 470 AXLE REPLACE, how to remove axle seal in a 1999 chevy malibu, size axle nut 2005 explorer, 2002 ford expedition trailing arm torque specs