Skip to content

stanadyne fuel leaking at shaft

You search PDF repair manual about stanadyne fuel leaking at shaft, if there are search results will appear below. If search results do not exist, please search by others keyword.

Rotary Fuel Pumps Timing to engine steps

download
SMALL | MEDIUM | LARGE Previous Next Fuel Injection Pump (Distributor Type) The fuel injection pumps, Bosch® VE, Lucas CAV DPA, Stanadyne DB4, Lucas CAV DPS, and Delphi DP210, are rotary distributor pumps. These pumps perform the four basic functions of: 1. Producing the high fuel pressure required for injection 2. Metering the exact amount of fuel for each injection cycle 3. Distributing the high-pressure, metered fuel to each cylinder at the precise time 4. Varying the timing relative to engine speed. SMALL | MEDIUM | LARGE Previous Next Distributor-Type Pump Governor Balance between the governor flyweights and control lever position controls the metering of the amount of fuel to be injected. The fuel injection pump governor performance and setting can affect engine power. Special equipment and qualified personnel are required to verify governor performance. If the seals are broken on the external Bosch® VE adjustment screw, the fuel rate can, perhaps, be out of adjustment The Lucas CAV DPA/DPS fuel injection pump uses a coded spring connection to change the governor setting. Incorrect connection of the governor spring can affect performance. Adjustments and rating changes are described in the Master Repair Manual, Injector Pumps and Injectors, Manual Shutdown Levers Both fuel injection pumps are equipped with mechanical shutdown levers. These levers are spring-loaded in the run position. Not all applications will use these manual shutdown controls and there will be no cable or rod connected to the lever. NOTE: Partial actuation of the mechanical shutdown levers will affect fuel flow and engine power. SMALL | MEDIUM | LARGE Previous Next Advance Timing Mechanism Regulated pressure produced by a vane supply pump in both fuel injection pumps is used to advance the timing as the engine speed increases. A return spring is used to retard the timing as the engine speed is reduced. If a spring breaks, the timing will go to the advance position, resulting in torque loss, fuel knock, and possible engine overheating. Retarded (late) timing will result in torque loss, high fuel consumption, and white to black smoke. SMALL | MEDIUM | LARGE Previous Next The Lucas CAV DPA/DPS advance timing mechanism uses a check ball in the circuit which, if omitted during assembly, will result in no timing advance. If the fuel injection pump has been replaced or the mechanism has been removed to fix a leak, the problem can be that the check ball is missing

2004 Audi A4 L4-1.8L Turbo FWD Fuel Pump Removal And Installation Manual

download
FWD Notes Removing And Installing Fuel Pump CAUTION: To remove the Fuel Pump (FP), the fuel tank may only be filled to a maximum of 3/4. Empty fuel tank if necessary. Recommended special tools and equipment 3087 wrench for tank sensor VAS5190 fuel siphoning device Empty fuel tank Observe safety precautions. Observe rules for cleanliness. CAUTION: Observe safety precautions when disconnecting the battery. Disconnect battery Ground (GND) strap with the ignition switched off. CAUTION: Secure Ground (GND) wire of VAS5190 to a blank portion of the chassis. Pull cone piece -2- from shaft piece -1- of VAS 5190. Using insulating tape, apply a mark -arrow- on hose at length a = 1465 mm from end of suction hose. Remove fuel filler cap from fuel filler tube Screw shaft piece -1- of VAS 5190 fuel siphoning device on to fuel filler tube of fuel tank . Now slide suction hose as far into fuel tank until the mark applied earlier -arrow- stands on shaft piece. NOTE: If using a siphoning device without shaft piece, proceed principally in the same manner In this case, apply a mark -arrow- on hose at length a = 1400 mm from end of suction hose using insulating tape. The suction hose is inserted correctly when the marking applied earlier stands opposite the lip of fuel filler tube. If the hose can only be inserted with difficulty, smear it thinly with engine oil. Never use lubricants containing silicon. Drain fuel tank through fuel filler tube. Carefully remove siphoning hose. Removing Sedan: Remove luggage compartment lining. Push forward the right backrest of rear seat, if necessary. Avant: Remove left 1/3 backrest. Remove left side trim in luggage compartment and dirt tray. All: Remove cover for connector flange (arrows). Release and disconnect harness connector -1-. Disengage electrical harness connector -2- and lay it aside. CAUTION: Work on the fuel system must only be performed when engine is cold. Fuel system is under pressure. Before opening system, place rags around the connection area. Then release pressure by carefully loosening connection Mark and disconnect fuel supply line -1- and fuel return line -3- (press release tab). Disconnect ventilation line -2- (press release button).

1998-2000 HONDA Accord L4 Replace the fuel pressure regulator, and reroute the fuel pressure regulator vacuum line

download
1. Locate and identify the three vacuum ports on the intake manifold. 2. Disconnect and discard the vacuum hose that connects the fuel pressure regulator to vacuum port C. 3. Plug vacuum port C with the cap from the tube kit. 4. Replace the fuel pressure regulator. Refer to page 11-113 of the 1998-00 Accord Service Manual. 5. Install the new vacuum hose kit using one of the following procedures 1. Remove and discard the cap from vacuum port A. 2. Connect the short vacuum hose to vacuum port A M/T WITH CRUISE CONTROL 2. Disconnect and discard the vacuum hose that connects the fuel pressure regulator to vacuum port C. 3. Plug vacuum port C with the cap from the tube kit. 4. Replace the fuel pressure regulator. Refer to page 11-113 of the 1998-00 Accord Service Manual. 5. Install the new vacuum hose kit using one of the following procedures. Zoom Sized for Print 1. Remove and discard the cap from vacuum port A. 2. Connect the short vacuum hose to vacuum port A. Zoom Sized for Print 3. Anchor the long vacuum hose by attaching it to the rear intake air duct clip and to the cruise control hose. . Route the new vacuum hose to the fuel pressure regulator. Attach the hose to the three rear clips on the engine wire harness cover. Zoom Sized for Print 1. Remove and discard the vacuum hose from vacuum port A. This hose supplies vacuum to the rear engine mount control solenoid. 2. Connect the short vacuum hose from the top of the Y fitting to vacuum port A

NISSAN FUEL SENDING UNIT REPAIR MANUAL

download
Replace the Fuel Sending Unit and apply Tectyl 517 (Bitumen) Wax Sealer to the Fuel Sending Unit Mounting Flange area. • Frontier: See page 11 for the Fuel Sending Unit Replacement and Wax Sealer application procedures. • Xterra: See page 25 for the Fuel Sending Unit Replacement and Wax Sealer application procedures. NOTE: During the Fuel Sending Unit replacement procedure, you’ll be instructed to inspect the Fuel Sending Unit Mounting Flange and O-Ring Groove (on the Fuel Tank). Based on the inspection results, you may have to replace the Fuel Tank. Add a “protective coating” to the Fuel Sending Unit connectors. • Frontier: See page 10 for the Fuel Sending Unit Protective Coating procedure. • Xterra: See page 24 for the Fuel Sending Unit Protective Coating procedure. End * A visual-aid “Pocket Card” was previously supplied to each dealer. For additional or replacement Pocket Cards, call the Resolve Corporation (formerly DDS Distribution) at (562) 698-2688. The part number for the Pocket Card is

1984-1995 Honda Accord/Prelude In­Tank Fuel Pumps TEST/REPAIR MANUAL

download
Carbureted Fuel System GENERAL INFORMATION On these vehicles, the engine management system is considered part of the emission control system. The major components include the carburetor(s), feedback control system, the air injection system, a throttle control system and the EGR system. The system consists of sensors and switches that feed information to the Electronic Control Unit (ECU), which will then operate several solenoid valves to maintain the ideal air/fuel ratio under all conditions. As useful as the tests found in this section are, the first step in repair or service to engine management systems is still to gain as much information as possible about the problem; when and under what conditions it occurs. At highway speed? At idle only? Only under heavy load or hard acceleration? Wet weather? Defining the problem will eliminate many systems from consideration and possibly point to the affected system. Before diving into an extended electrical diagnosis, take the time to review the basics. Check every vacuum line for cracks or leaks. Check every electrical connector for corrosion or loose pins. Quite often, simply unplugging and reconnecting a connector will break up corrosion on the pins and restore the circuit. Watch out for poor grounds, particularly if the car has experienced major bodywork. COMPONENT TESTING Air Injection System The purpose of this system is to supply oxygen to the exhaust stream at a point in the exhaust manifold that is hot enough to burn off some of the hydrocarbon emissions. The main component is an air suction valve. The valve is spring loaded to stay closed, with engine vacuum supplied to a diaphragm that reduces the spring pressure and allows the reeds to open. The ECU regulates the engine vacuum to the diaphragm by operating a solenoid valve. 1. With the engine at normal operating temperature and at idle, remove the air cleaner and listen for a bubbling sound at the air suction port. There should be no sound at idle, meaning the air suction valve is closed. 2. If the noise is heard at the air suction port, disconnect the vacuum hose at the air suction valve and connect a vacuum gauge to the hose. There should be no vacuum. If there is vacuum and the noise stops, the problem is in the control system. If there is no vacuum and the bubbling sound is still there, the air suction valve is defective and must be replaced. 3. To test the valve, draw a vacuum at the air suction valve diaphragm and listen for a bubbling sound at the air suction port. If no sound is heard, the air suction valve or diaphragm is faulty. Throttle Control System