starter relay wiring diagram lincoln navigator

You search PDF repair manual about starter relay wiring diagram lincoln navigator, if there are search results will appear below. If search results do not exist, please search by others keyword.



  starter relay wiring diagram lincoln navigator Direct Download speed 5432 Kb/s

  starter relay wiring diagram lincoln navigator Full Version speed 8172 Kb/s



1998 Acura 3.5RL FUEL PUMP RELAY (3.5RL) INSTALLATION MANUAL

0

Filed Under (Acura Manuals) by admin on 13-06-2011

download
Fuel pump relay is located in the front of the trunk. Turn ignition switch to START position. If engine starts, go to next step. If engine does not start, go to FUEL PUMP RESISTOR (3.5RL) . 2. Turn engine off and ignition on. Measure voltage between ground and PCM 12-pin connector terminal No. 4 (Green wire). If battery voltage is present, go to next step. If battery voltage is not present, go to step 4). 3. Start engine and run at 3000 RPM with no loads and transmission in Park or Neutral, until radiator fan comes on. Allow engine to idle for at least one minute. Turn engine off. Disconnect vacuum hose No. 21 from vacuum manifold. Apply 8-12 in. Hg (27-40 kPa) vacuum to Manifold Absolute Pressure (MAP) sensor. Start engine and run at 6500 RPM with no loads and transmission in Park or Neutral. Measure voltage between ground and PCM 12-pin connector terminal No. 4 (Green wire). If less than one volt is present, fuel pump relay circuit is okay. If one volt or more is present, substitute a known good PCM, then recheck. If symptom or indication goes away, replace original PCM. 4. Turn ignition off. Disconnect PCM 26-pin and 12-pin connectors. Disconnect fuel pump relay 4-pin connector. Using a fused jumper wire, connect fuel pump relay connector terminals No. 2 (Red/White wire) and No. 4 (Green wire). Turn ignition on. Measure voltage between ground and PCM 12-pin connector terminal No. 4 (Green wire). If battery voltage is not present, go to next step. If battery voltage is present, replace fuel pump relay. 5. Remove jumper wire. Measure voltage between ground and fuel pump relay 4-pin connector terminal No. 2 (Red/White wire). If battery voltage is present, repair open or short in Green wire between PCM and fuel pump relay. If battery voltage is not present, repair open in Red/White wire between fuel pump relay and FUEL PUMP fuse No. 22 (20-amp), located in underdash fuse/relay box. FUEL PUMP RESISTOR (3.5RL) 1. Fuel pump resistor is located in the left corner of the trunk. Disconnect fuel pump resistor 2-pin connector. Turn ignition on and measure voltage between ground and fuel pump resistor connector terminal No. 2 (Yellow wire) within 2 seconds. If battery voltage is present for 2 seconds after ignition is turned on, go to next step. If battery voltage is not present as specified, check PGM-FI relay. See PGM- FI MAIN RELAY . 2. Turn ignition off. Using a jumper wire, connect fuel pump resistor connector terminals No. 1 (Black/Yellow wire) and No. 2 (Yellow wire). Turn ignition switch to START position. If engine does not start, go to next step. If engine starts, replace fuel pump resistor. 3. Turn ignition off. Disconnect fuel unit sub-harness Gray, 10-pin connector located in front of trunk, above fuel pump access panel, next to Gray, 20-pin connector. Turn ignition on and measure voltage between ground and sub-harness connector terminal No. 7 (Black/Yellow wire) within 2 seconds. If battery voltage is present for 2 seconds after ignition is turned on, check fuel pump. If battery voltage is present as specified, repair open in Black/Yellow wire between fuel pump resistor and fuel pump

Related Content:

1998 jimmy fuel pump install, wire diagram on a 2002 grand prix headlight, 03 ford windstar fuel pump wiring, 86 corvette wiring schematics, location of vent valve solenoid on 2010 ford ranger, damaged fuel pump wiring, proper connection for horn relay 1968 chevelle, fan cable for 1998 dodge caravan, 1998 s10 6 cylindes fuel regulator diagram, pontiac grand am fuel pump wireing harness replacement instructions

1998 Dodge Grand Caravan Fuel Pump Relay Removal And Installation Manual

0

Filed Under (Dodge Manuals) by admin on 13-06-2012

download
Fuel Pump Relay 1. Remove fuel pump relay from power distribution center at driver’s side front corner of engine compartment, near the battery. Note terminal identification on fuel pump relay. See Fig. 6 . 2. To check fuel pump relay resistance, use ohmmeter and check resistance between terminals No. 85 and 86 on fuel pump relay. Replace fuel pump relay if resistance is not 70-80 ohms. 3. To check fuel pump relay operation, connect ohmmeter between terminals No. 30 and 87A on fuel pump relay. See Fig. 6 . Ohmmeter should indicate continuity between terminals No. 30 and 87A on fuel pump relay. 4. Connect ohmmeter between terminals No. 30 and 87 on fuel pump relay. See Fig. 6 . Ohmmeter should indicate no continuity between terminals No. 30 and 87 on fuel pump relay. 5. Connect 16-gauge jumper wire between negative battery terminal and terminal No. 85 on fuel pump relay. Connect 16-gauge jumper wire between positive battery terminal and terminal No. 86 on fuel pump relay. 6. Fuel pump relay should now be energized. No continuity should now exist between terminals No. 30 and 87A on fuel pump relay. Continuity should now exist between terminals No. 30 and 87 on fuel pump relay. Disconnect jumper wires. Replace fuel pump relay if defective. 7. If fuel pump relay or wiring circuit failure exists, a Diagnostic Trouble Code (DTC) will be stored in Powertrain Control Module (PCM). See appropriate G – TESTS W/CODES article. Fig. 6: Identifying ASD Relay & Fuel Pump Relay Terminals Courtesy of CHRYSLER CORP.

Related Content:

yhs-default, fuse for right headlight eclipse 2000, location of fan relay 98 trans am, which is the fuel pump relay on 2011 durango, sensor switch on rear beam axle of 2005 saturn relay, where is the washer relay located in a 2009 chevy impala, where is the relay switch for liftgate in 2005 esclade, 99 eldorado fuel pump relay test, 1993 corvette power seat and power window shorting out breaker, relay unit be31 107

Honda Navigation System Information and DVD Information and Inspection Manual

0

Filed Under (Honda Manuals) by admin on 06-07-2012

download
REVISION SUMMARY •Under BACKGROUND, more sources for navigation service and user information are listed. •Under DVD LABEL COLOR IDENTIFICATION BY MODEL, the Latest DVD Version available is updated. •Under REPLACING THE NAVIGATION CONTROL UNIT AND TRANSFERRING THE NAVIGATION DVD, a step was added to Save Users Memory when replacing the navigation control unit. •Under ENTERING THE ANTI-THEFT CODE, the instructions about obtaining the serial number from a navigation unit without removing it were clarified. •Under NAVIGATION SYSTEM PLATFORMS, HFL was added to the list of Distinguishing Features . BACKGROUND Use this information to avoid possible customer dissatisfaction issues caused by incorrect or outdated DVD installation. For more information about the navigation system and its operation, refer to the following resources: •Service Manual – Printed or on ISIS •Quick Start Guide •Online University – Use the keyword NAVI . •Navigation System Manual – Besides the one that comes with the vehicle, the navigation system manual is also available online. Select SEARCH BY PUBLICATION , select Consumer Information , select your applicable vehicle, then select Navigation Manual from the list. •Service Bulletins – Use the keyword NAVI . •ETM (electrical troubleshooting manual) This bulletin provides the following navigation system DVD service information: •DVD label color identification by model •Earliest DVD version application for each model •How to identify navigation DVD versions •Checking a DVD for damage •Ordering a DVD •Navigation DVD stocking concerns •DVD handling and cleaning •Installing a navigation DVD •Precaution on customer “sneak previews” of a newer navigation DVD version •Answering customer questions about navigation coverage and POI (point of interest) •Pitfalls when interchanging navigation DVD/parts during diagnosis •Replacing the navigation control unit and transferring the navigation DVD •Entering the anti-theft code •Navigation system platforms VEHICLES AFFECTED • 2003-09 Accord • 2005-07 Accord Hybrid • 2006-09 Civic • 2006-09 Civic Hybrid • 2007-09 CR-V • 2009 Element • 2009 Fit • 2000-09 Odyssey • 2003-09 Pilot • 2006-09 Ridgeline WARRANTY CLAIM INFORMATION None. This service bulletin is for information only. Refer to the flat rate manual whenever servicing or repairing the navigation system

Related Content:

manual lincoln navigator 2007, c1998 module calibration failure navigator 2006, exploded view 4r55e, service manual for civic 2007, honda elysion ecu pin voltage, 2005 odyssey service manual free, 2003 honda odyssey service manual, reset liftgate lincoln, invision revolution dvd manual, lincoln navigator 1998 fuses oxygen

2000 Dodge Dakota & Durango Power Windows ADJUSTMENTS

0

Filed Under (Dodge Manuals) by admin on 18-06-2012

download
ADJUSTMENTS WINDOWS Remove door trim panel. See DOOR TRIM PANEL under REMOVAL & INSTALLATION. Loosen bolts holding window to regulator. Raise window fully, seating window in frame. Tighten bolts. Install door trim panel. TROUBLE SHOOTING POWER WINDOWS On Dakota, inspect circuit breaker No. 20 (20-amp) in junction block. On Durango inspect circuit breaker No. 21 (25-amp) in junction block. On all models, junction block is located on left end of instrument panel. Inspect fuse No. 9 (40-amp on Dakota, 50-amp on Durango) in Power Distribution Center (PDC). PDC is located in left front corner of engine compartment. Inspect power window system ground circuit. See WIRING DIAGRAMS . SYSTEM TESTS ALL WINDOWS INOPERATIVE Dakota 1. Check circuit breaker for power window system. See TROUBLE SHOOTING . Replace circuit breaker as necessary. If circuit breaker is okay, go to next step. 2. Disconnect negative battery cable. Remove driver’s front power window switch. See POWER WINDOW SWITCH under REMOVAL & INSTALLATION. Check for continuity between ground and terminal No. 3 (Black wire) at driver power window switch wiring harness connector. If continuity exists, go to next step. If continuity does not exist, repair open in Black wire between driver power window 2000 Dodge Durango 2000 ACCESSORIES & EQUIPMENT’ ‘Power Windows – Dakota & Durango 2000 Dodge Durango 2000 ACCESSORIES & EQUIPMENT’ ‘Power Windows – Dakota & Durango switch connector and ground. See WIRING DIAGRAMS . 3. Connect negative battery cable. Turn ignition on. Measure voltage between ground and terminal No. 5 (Tan wire) at driver’s power window switch wiring harness connector. If battery voltage is present, check driver power window switch. See POWER WINDOW SWITCH under COMPONENT TESTS. If battery voltage is not present, repair open Tan wire between driver power window switch connector and ignition switch. See WIRING DIAGRAMS . See POWER DISTRIBUTION article in WIRING DIAGRAMS. Durango 1. Check circuit breaker for power window system. See TROUBLE SHOOTING . Replace circuit breaker as necessary. If circuit breaker is okay, go to next step. 2. Disconnect negative battery cable. Remove driver’s front power window switch. See POWER WINDOW SWITCH under REMOVAL & INSTALLATION. 3. Check for continuity between ground and terminal No. 5 (Black wire) at driver’s power window switch wiring harness connector. If continuity exists, go to next step. If continuity does not exist, repair open in Black wire between driver’s power window switch connector and ground. See WIRING DIAGRAMS . 4. Reconnect negative battery cable. Turn ignition on. Measure voltage between ground and terminal No. 4 (Tan wire) at driver’s power window switch wiring harness connector. If battery voltage is present, check driver’s power window switch. See POWER WINDOW SWITCH under COMPONENT TESTS. If battery voltage is not present, repair open Tan wire between driver power window switch connector and ignition switch. See WIRING DIAGRAMS . See POWER DISTRIBUTION article in WIRING DIAGRAMS. ONE WINDOW INOPERATIVE

Related Content:

1993 dakota 3 9 fuse diagram, lucas a127 wiring, 1998 Dodge Dakota Service Manual, 2003 s10 airbag wiring diagram, zimmatic pivot wiring, dodge durango 2002 suspension layout, abs and Anti Theft Passive 2000 mercury cougar, free 1997 buick regal gs wiring diagrams, Service manual dodge durano 2002 pdf, 2000 Buick LeSabre Wiring Diagram

2007-2011 Toyota Tundra Fog Light Kit INSTALLATION INSTRUCTIONS

0

Filed Under (Toyota Manuals) by admin on 14-03-2012

download
Installation 1. Secure the Relay to the wire loom next to the Battery with wire ties. Secure top and bottom with wire ties (see Picture 1). Note: It is suggested to loosen the battery from the base and move it to allow extra working room. Picture 1 2. Attach the ring terminal with 2 black wires to the 10mm ground bolt next to the battery (see picture 2) Run the fog light wire harness on the driver side of the car. Use wire ties as needed Vehicle Disassembly 5. Remove the screws on the lower part of the instrument panel (picture 6) Picture 6 6. Remove lower instrument panel sub assy (picture 6) 7. Mount switch into switch knockout on left side of dash (see picture 9) Picture 9 8. From inside the cabin, locate the wires that were pushed through in step 4. It will be the grommet above the gas pedal (see picture 10) Picture 10 9. Install switch harness (see picture 11) Picture 11 10. Locate the junction box behind the lower instrument panel (picture 12) Picture 12 11. T-tap green/black wire from fog light harness to connector DB pin 16, red wire (bottom pin on right). Connector DB is in the driver’s side junction box, located on the left side of the steering column (pic. 13 & 14) 12. T-Tap orange/black wire from fog light harness to connector DB pin 18, blue wire (right side third pin up from bottom). Connector DB is left of steering wheel (picture 13 and 14) Picture 13: Close up of junction box, viewed from driver’s seat Picture 14A Picture 14B Picture 14A: Diagram of junction box, driver’s seat view Picture 14B: DB connector (showing Pin 16 and 18) 13. Secure with wire ties. 14. Reinstall dash panels 15. Route the fog light wire under car. 16. Remove splash shields 17. Remove both front bumper hole covers. Detach wire harness clamps and release the 3 claws and remove (picture 15) Picture 15 18. Re-secure detached wire harness and plug in left side fog light into harness plug and secure with wire ties. Snap fog light bezel into bumper hole (picture 16) Picture 16 19. Run right side of wire harness through bumper sub frame to right fog lamp opening (see picture 17

Related Content:

how to change steering belt toyota echo 2003, 94 tbird fuses, 08 silverado taillights wiring harness installation, h3 wiring harness causing turn signal problem, jaguar etype hanbrake wire, kia data link connector, kia sorento 2007 drivers seat electrical connection, kia sorento 2007 drivers seat electrical plug wiring, location of horn relay on toyota tundra 2011 model, motor controllert for a 2007 ruff-n-tuff

1995 Volvo 850 L5-2.3L Turbo Relay Identification and Location

0

Filed Under (Volvo Manuals) by admin on 02-05-2012

download
Relay Identification and Location Relays Inside the Central Electrical Unit 101-102Control module, cruise control (4/3) 103 Fuel pump relay (2/23) 104,108Main headlight relay with bulb malfunction indicator (2/1) 105 Overload relay +X supply (2/30) 106 Overload relay +15 supply (2/31) 107 Overload relay +X supply (2/60) 201 Fog light relay (2/2) 202 Relay, deadlock setting (2/47) 203 Relay, windshield intermittent wiper (2/4) 204 Relay, tailgate intermittent wiper (2/16) 205-206Relay, central lock and delayed inside lighting (2/7) 207 Speed warning (2/51) or exhaust temp. sensor relay (2/15) 208 Relay, heated rear window and door mirrors (2/44) 210-211Relay, anti-theft alarm (2/28) 212 Relay, seat belt reminder/key warning (2/5) 213 Front fog lights, bridge (25/9) 214 Relay, heated rear seat (2/43) If the car is not equipped with a theft alarm, position 210 is bridged and 211 is unconnected. Relays Outside the Central Electrical Unit

Related Content:

diagram gearbox kancil, kancil 850 central lock wiring diagram

1995-1996 Toyota Avalon Factory Disarm Installation Manual

0

Filed Under (Toyota Manuals) by admin on 07-03-2012

download
There is only one way to bypass the factory alarm on this vehicle. All other conventional methods (such as finding the wire that runs from the driver’s door lock cylinder), will disarm and unlock the doors. To disarm the alarm only, you’ll need to find the 18 AWG. Red/ Yellow wire that runs from the ignition switch. This wire can be identified by making sure it is negative while the key is in the run position. When found connect the A White/Black Ignition 3 wire to the Red/Yellow wire. This will now disarm but not unlock the door’s. All Nissan Altima and Toyota Tercel vehicles share a similar problem. If these vehicles are not started using the ignition key, two terminals of the ignition key cylinder overlap causing a feedback condition to occur when the vehicle’s true ignition wire is powered up by the AutoCommand®. Essentially, when the main ignition in these vehicles is powered, voltage feeds backwards through the ignition cylinder back out to the starter wire resulting in the starter holding on. The solution is to interrupt the START wire(s) using a relay, preventing this feedback after the AutoCommand® has started the car. The diagram on the next page details the relay layout for solving this problem on these vehicles

Related Content:

1995 Toyota Tercel 1 5L EFI DOHC 4cyl pdf, bypass starter intrupt relay, SPARK IGNITION CYLINDER ARRANGEMENT PDF

Toyota Landcruiser / Scout Weatherproof Harness Wire Harness Installation Instructions

0

Filed Under (Toyota Manuals) by admin on 05-03-2012

download
Grounding the Automobile A perfectly and beautifully wired automobile will nevertheless have bugs and problems if everything is not properly grounded. Do not go to the careful effort of installing a quality wire harness only to neglect proper grounding. Note: The Painless Wire Harness Kit includes no ground wire except the black wire from the two headlamp connectors. You must supply ground wire (14-16 gauge) for all circuits. 6.3.1 Connect a Ground Strap or Cable (2-gauge minimum) from the Negative Battery terminal to the automobile chassis (frame). 6.3.2 Connect a Ground Strap from the Engine to the chassis (even a 10-gauge wire is too small) . DO NOT RELY UPON THE MOTOR MOUNTS TO MAKE THIS CONNECTION . 6.3.3 Connect a Ground Strap from the Engine to the Body. 6.3.4 If you have a fiberglass body you should install a terminal block to ground all your Gauges and Accessories. Ground the Terminal Block with at least a 12-gauge wire to the chassis. 6.4 Terminal Installation and Making Connections Note: In the following steps you will be making the circuit connections. Before you start, you should carefully read Sections 7.0 through 10.0 , as appropriate, and continually refer to Section 10.0 , DOUBLE- CHECKING your routing and length calculations before cutting any wires and making connections. Give special attention to Turn Signal and Ignition Switch connections. These can be somewhat confusing. 6.4.1 Have all needed tools and connectors handy. 6.4.2 Select the correct size terminal for the wire and stud application. 6.4.3 Determine the correct wire length and cut the wire. Remember to allow enough slack in the harness and wires at places where movement could possibly occur, such as automobile body to frame, frame to engine, etc. Double-check your calculations. 6.4.4 Strip insulation away from wire. Strip only enough necessary for the type of terminal lug you are using. Note: In the following step, make sure that the terminal is crimped with the proper die in the crimping tool. An improper crimp will NOT make a good connection. 6.4.5 Crimp the terminal onto the wire. CAUTION: DO NOT OVER-CRIMP! 6.4.6 Connecting the harness throughout the groups is a redundant process. Make sure that each wire is FIRST properly routed and THEN attach. DO NOT ATTACH FIRST THEN ROUTE AFTERWARD. 6.4.7 When all wires are attached, tighten the mounts and ties to secure harness permanently. 6.5 Testing The System 6.5.1 Use a small (10 amp or less) battery charger to power up the vehicle for circuit testing. If there is a problem anywhere, the battery charger’s low amperage and internal circuit breaker will provide circuit protection. CAUTION: IF YOU HAVE NOT YET DISCONNECTED THE BATTERY FROM THE AUTOMOBILE, DO SO NOW! DO NOT CONNECT THE BATTERY CHARGER WITH THE BATTERY CONNECTED. Connect the battery charger’s NEGATIVE output to the automobile chassis or engine block and its POSITIVE output to the automobile’s positive battery terminal. 6.5.2 INDIVIDUALLY turn on each light, ignition, wiper circuit, etc. and check for proper operation. Note: The turn signals will not flash properly if you do not have both the front and rear bulbs installed and connected. 6.5.3 When all circuits check out THEN attach the battery cable to the battery for vehicle operation

Related Content:

where are the battery terrminals on a 2012 pruis, 1996 ford f53 chassis circuit board diagram, 1996 ford F53 wiring diagrams, 97 cadillac deville ground location, FORD E-450 FUEL PUMP WIRING

1993 Ford Escort CIRCUIT TEST J – FUEL PUMP CIRCUIT (RELAY AND INERTIA SWITCH)

0

Filed Under (Ford Manuals) by admin on 19-01-2012

download
resistance between test pin No. 22 and test pins No. 40 and 60. If resistance is less than 10,000 ohms, repair short circuit and repeat QUICK TEST. If resistance is 10,000 ohms or more, go to step 5). 5)Check Fuel Pump Circuit Continuity Turn ignition off. Leave fuel pump relay and PCM disconnected. Measure resistance between FUEL PUMP circuit at fuel pump relay wiring harness connector and test pin No. 22 at breakout box. If resistance is less than 5 ohms, replace PCM and repeat QUICK TEST. If resistance is 5 ohms or more, repair open circuit and repeat QUICK TEST. 10)Code 95/542 A KOEO Code 95/542 indicates one of the following conditions: Engine Starts: * Fuel pump secondary circuit shorted to power. * Fuel pump relay contacts always closed. * Open FPM circuit between PCM and junction to POWER-TO-PUMP circuit. * Left/front HO2S short to power (dual HO2S applications). * Faulty PCM. No Start: * IFS switch circuit open or not reset. * Open circuit in or between PCM and fuel pump. * Faulty ground connection at fuel pump. * Faulty fuel pump. If engine starts, go to step 11). If engine does not start, go to step 15). 11)Check Fuel Pump Operation Turn ignition on. Wait 5 seconds. Listen for fuel pump operation. If fuel pump is off, go to step 13). If fuel pump is on, go to step 12). 12)Check For Fuel Pump Relay Always Closed Turn ignition off. Disconnect fuel pump relay. Turn ignition on. If fuel pump is off with relay disconnected, replace fuel pump relay and repeat QUICK TEST. If fuel pump is on with relay disconnected, repair short to power in POWER-TO-PUMP or FPM circuit. (For models with relay block, also check fuel pump prime plug circuit). Repeat QUICK TEST. 13)Check Continuity Of Fuel Pump Monitor (FPM) Circuit Turn ignition off. Disconnect PCM 60-pin connector. Inspect and repair any damaged terminals. Install EEC-IV Breakout Box (T83L-50-EEC-IV) , leaving PCM disconnected. Disconnect fuel pump relay. Measure resistance between test pin No. 8 (No. 19 on Escort, and Tracer) at breakout box and POWER-TO-PUMP circuit at fuel pump relay wiring harness connector. If resistance is less than 5 ohms, go to step 25) (dual HO2S) or replace PCM and repeat QUICK TEST (single HO2S). If resistance is 5 ohms or more, repair open circuit and repeat QUICK TEST

Related Content:

99 subaru forester fuel line repair kits, lucas cav injection pump diagram, bp44 repair manual pdf, toyota so5d engine fule pump control wireing diagram pdf, CAV Fuel Injector Pump (Ford Part #D6NN9A543G) repair manual, timing a farmtrac 555, 2002 isx cummins manual pump installation, 89 dodge dakota fuel pump diagram, how to change water pump on a dewoo, rager injection pump parts manual

1995 Toyota 4Runner STARTING AND CHARGING SYSTEMS REPAIR MANUAL

0

Filed Under (Toyota Manuals) by admin on 15-03-2012

download
TROUBLE SHOOTING NOTE: See TROUBLE SHOOTING – BASIC PROCEDURES article in GENERAL INFORMATION. 1) If a no-start condition exists and battery is known to be good, connect test light or voltmeter between starter solenoid terminal No. 50 and ground. See Figs. 6 and 7. 2) Turn ignition switch to START position. If test light or voltmeter does not indicate voltage, check main fusible links and large ampere main fuses in engine compartment relay box. If fusible links and fuses are okay, see IGNITION SWITCH CONTINUITY TEST and/or STARTER RELAY TEST under ON-VEHICLE TESTING. ON-VEHICLE TESTING NOTE: Before testing, ensure battery is fully charged, battery cables and terminal ends are tight and clean, and engine grounds are secure. CLUTCH START SWITCH TEST 1) Switch is located above clutch pedal on bracket. Disconnect wiring harness connector from switch. 2) Connect ohmmeter probes to switch terminals. Depress clutch pedal. If continuity does not exist, adjust or replace clutch start switch. If continuity exists, check circuit to starter relay for open, and check starter relay. See STARTER RELAY TEST. CLUTCH START CANCEL SWITCH TEST 1) Locate switch in left dash panel. Remove right lower instrument panel to access switch connector. Disconnect wiring harness connector from switch pigtail connector. See Fig. 1. 2) Connect negative lead of ohmmeter to terminal No. 1. Ensure continuity does not exist between connector terminals No. 1 and 2, terminals No. 1 and 3, and terminals No. 2 and 3. Check operation of switch by connecting jumper wires from 12-volt battery. Connect positive lead to terminal No. 3 and negative battery lead to terminal No. 1. 3) Using ohmmeter, ensure continuity does not exist between connector terminals No. 1 and 2 until switch button is pushed. When switch button is pushed, switch light should come on and continuity should exist. Disconnect battery and ensure continuity does not exit between terminals No. 1 and 2. If switch does not test as specified, replace switch. Fig. 1: Identifying Clutch Start Cancel Switch Connector Terminals Courtesy of Toyota Motor Sales, U.S.A., Inc. IGNITION SWITCH CONTINUITY TEST WARNING: Deactivate air bag system before performing any service operation. For 1996 4Runner, see AIR BAG RESTRAINT SYSTEM article. 1995 1) Disconnect negative battery cable. Removedriver’s lower instrument panel cover. Remove upper and lower steering column covers if needed. Locate ignition switch wiring harness 8-pin connector. See Figs. 2-3. 2) With ignition switch in LOCK position, there should be no continuity between any terminals. With ignition switch in ACC position, there should be continuity between terminals No. 2 and 3. With ignition switch in ON position, there should be continuity between terminals No. 1, 2 and 3, and between terminals No. 7 and 8. 3) With ignition switch in START position, there should be continuity between terminals No. 1, 4 and 6, and between terminals No. 7 and 8. If continuity is not as specified, replace switch.

Related Content:

how do i install ignition switch on 1996 chevy pickup, how to replace a 1990 Toyota Corolla Ignition switch, g6 testing key switch, 2007 chevy silverado brake switch installation, what causes 2005 toyota sienna starter relay to burn out, how to take ignition switch out of kia sorento, how toremuve thh ignition key on chrysler 2002 concord LX1 or baypass, ignition switch removal on 2003 buick century, ignition switch wiring diagram 2006 chevrolet uplander, where is ignition switch 01 silverado

Related Content:

1998 jimmy fuel pump install, wire diagram on a 2002 grand prix headlight, 03 ford windstar fuel pump wiring, 86 corvette wiring schematics, location of vent valve solenoid on 2010 ford ranger, damaged fuel pump wiring, proper connection for horn relay 1968 chevelle, fan cable for 1998 dodge caravan, 1998 s10 6 cylindes fuel regulator diagram, pontiac grand am fuel pump wireing harness replacement instructions