super duty parking brake assembly

You search PDF repair manual about super duty parking brake assembly, if there are search results will appear below. If search results do not exist, please search by others keyword.



  super duty parking brake assembly Direct Download speed 5432 Kb/s

  super duty parking brake assembly Full Version speed 8172 Kb/s



2000 Ford F-Super Duty 250-550/ Excursion/ F-53 Motorhome Chassis Workshop Manua

0

Filed Under (Ford Manuals) by admin on 19-02-2011

download
Removal 1. Set the parking brake. 2. Loosen the retaining bolts. 3. Raise the vehicle to the desired working height, keeping the axle parallel with the floor; for additional information, refer to Section 100-02 . 4. Release the parking brake. 5. Remove the wheel(s); for additional information, refer to Section 204-04 . 6. Remove the brake caliper and rotor on the single rear wheel axle; for additional information, refer to Section 206-04 . 7. Remove the retaining bolts and axle shaft. 9. d the hub nut if es apart during removal. no circumstances e operations. NOTE: The hub nut will ratchet during this operation. Remove the hub nut (counterclockwise for right-hand thread; clockwise for left-hand thread). 10. Install the Step Plate. 11. Install the 2-Jaw Puller and loosen the rear hub to the point of removal. 12. hub bearing when b. Remove the rear hub assembly. 3. l a new hub seal ub assembly is removed. NOTE: The inner bearing is located behind the hub seal. Pack each bearing and replace the hub seals; for additional information, refer to Bearings, Cups and Seals in this section. 14. treme care not to scratch or gouge the seal or bearing surfaces. If after hub removal, the hub seal or seal inner sleeve remains on the spindle, remove it as shown using the Step Plate and the 2-Jaw Puller. 15. Inspect the seal surface and inner shoulder for scratches and damage. ? Remove all scratches, gouges or galling damage with #600 or finer crocus cloth. Installation 1. NOTE: Clean the spindle thoroughly after removing the rear hub. Coat the spindle with axle lubricant. 2. b bearings must be prelubed prior to installation. Fill the hub cavity with 29.6 ml (1 oz) of SAE 75W-140 High Performance Rear Axle Lubricant F1TZ-19580-B or equivalent meeting Ford specification WSL-M2C192-A. 3. treme care not to damage the hub g it to contact the spindle during installation. NOTE: Coat the spindle and hub seal inside diameter with SAE 75W-140 High Performance Rear Axle Lubricant F1TZ-19580-B or equivalent meeting Ford specification WSL- M2C192-A. NOTE: Installing the rear hub in this manner causes the outer bearing to act as a pilot making the installation easier. Push the rear hub and outer bearing onto the spindle as an assembly. ? Hold the outer bearing seated and use the bearing as a pilot

Related Content:

how to change a rear wheel hub on 2009 nissan maxima, how to repair a wheel seal on a 2004 f250, how to replace wheel bearings on 2005 acura mdx diagram

FORD F450/ 550 SUPER DUTY CHASSIS CABS OWNERS MANUAL

0

Filed Under (Ford Manuals) by admin on 21-05-2012

download
LATERAL CONTROL ROD AXLE BRACKET INSTALLATION 1. Remove and discard the OEM shock absorbers, but retain the mounting fasteners (bolts & nuts) for re-use. 2. Remove the top d-bushing mount bolts and disconnect the axle breather tube (See Figure 2- 1). 3. If the truck is equipped with an S110 4.25″ X 4.25″ square axle (most F450s and F550s), install both axle spacer tabs on the axle bracket using (4) 1/2 x 1 1/4 UNC FLANGE BOLTS and (4) UNC TOP LOCK FLANGE NUTS. (See Figure 2-2). 4. Loosely fasten the axle bracket to the axle as shown in Figure 2-3 using (2) M12 x 1.75 x 40 METRIC BOLTS and (2) 1/2″ WASHERS. 5. Reconnect the axle breather tube to the axle. LATERAL CONTROL ROD (LCR) FRAME BRACKET INSTALLATION 1. On the PASSENGER side, remove to two top rivets from the OE bumper bracket and ream the holes to 0.47″ (See Figure 3-1) 2. Install the frame bracket as shown in Figure 3-2 using (4) 7/16 UNC TOP LOCK FLANGE NUTS. FIG. 3-2 Frame bracket Remove these two rivets and ream to 0.47″ DRIVER SIDE DISASSEMBLY 1. With weight taken off the rear springs, as noted in pre-installation checklist, remove the rear leaf spring hanger. Removal of the rear overload spring bracket is optional See Figure 4-1. 2. Remove the front spring hanger bracket and the front overload spring bracket. (See Figure 4-2). 3. Remove existing U-bolts that attach the axle to the leaf spring and keep the OE U-bolt plate for later use. (See Figure 4-3) After this is done, the axle, spring, and hanger will be loose. Remove and discard the spring and hangers from the axle.DRIVER SIDE ASSEMBLY 1. Review Figure 5-1 & Figure 13-2 to acquaint yourself with the various parts of the UltraRide suspension. 2. Fasten the Front Hanger to the frame using (6) 9/16 x 1-1/2 UNF BOLTS, (6) 9/16 UNF NUTS, and (12) 9/16 FLAT WASHERS. Route the parking brake cables through the corresponding holes on the Front Hanger. 3. Assemble the Suspension Arm to the axle using (2) M20 X 2.50, 79 X 425 METRIC U- BOLTS, (4) M20X2.5 METRIC NUTS, and original OE top plate and axle bracket. Make sure the arm/axle locating pin is properly inserted into the mating hole on the axle pad and that the bottom side of the arm rests evenly on the axle pad. 4. Insert the Bolt Spacer Tube into the arm bushing and loosely fasten the arm to the front hanger using (1) 3/4 X 7 UNF BOLT, (1) 3/4 UNF NUT, (2) 3/4 WASHERS, and (2) plastic wear washers. 5. Loosely fasten the Lateral Control Rod Axle Bracket to the Arm using (2) 1/2 X 1-1/4 UNC FLANGE BOLTS (See Figure 5-2). 6. Bolt the Air Spring Bracket Assembly to the frame using (5) 1/2 X 1-1/4 UNC FLANGE BOLTS and (5) 1/2 UNC TOP LOCK FLANGE NUTS. One frame hole will need to be reamed to 0.53″ on each side. See Figure 5-2. 7. Bolt the Air Spring to the Suspension Arm using (1) 1/2 UNC JAM NUT. Make certain the air spring is not twisted or creased after tightening the nut.

Related Content:

how to change a rear wheel hub on 2009 nissan maxima, how to repair a wheel seal on a 2004 f250, how to replace wheel bearings on 2005 acura mdx diagram