Skip to content

suspension diagram 2000 taurus

You search PDF repair manual about suspension diagram 2000 taurus, if there are search results will appear below. If search results do not exist, please search by others keyword.

1999 Jaguar XJ8 Vanden Plas SUSPENSION ADJUSTMENTS And Installation Manual

download
ADJUSTMENTS & INSPECTION WHEEL ALIGNMENT SPECIFICATIONS & PROCEDURES HUB BEARING PRELOAD Hub bearing preload is controlled by shim adjustment between hub assembly and hub outer bearing. Shims are available in various thicknesses. Checking 1. Raise and support vehicle. Remove wheel assembly. Clamp dial indicator mount to hub carrier. Ensure dial indicator pointer contacts hub flange. 2. Using 2 levers between hub and hub carrier, press hub outward. Note reading on dial indicator. The difference between dial indicator readings is preload of hub bearing. For adjustment, see HUB CARRIER under REMOVAL & INSTALLATION. REAR SUSPENSION HEIGHT 1. Ensure vehicle has full fuel tank, all fluids are topped off and tire pressures correct. Roll vehicle about 30 feet on a level surface. Measure distance between differential support plate at both sides and ground. See Fig. 2 . 2. Height measurement for coupe and convertible. If height is not within specification, check all bushings and replace as necessary. If bushings are okay, replace rear springs. NOTE: See SPECIFICATIONS & PROCEDURES article in WHEEL ALIGNMENT. 1999 Jaguar XJ8 Vanden Plas 1999-2000 SUSPENSION’ ‘Rear Fig. 2: Measuring Rear Suspension Height Courtesy of JAGUAR CARS, INC. REMOVAL & INSTALLATION “A” FRAME Removal 1. Raise vehicle and support with stands. Remove “A” frame to final drive unit rear bracket securing bolts and front bracket inner securing nuts and bolts. See Fig. 3 . 2. Position a suitable wood and jack under final drive unit drive flange, operate jack to support final drive unit. Unscrew and remove both “A” frame outer bush to body and bracket securing bolts. See Fig. 4 . Unscrew and remove “A” frame left and right outer bush bracket to body securing bolts. 3. Lower jack approximately one inchto improve access. Unscrew and remove “A” frame to final drive unit front bracket intermediate securing bolts. Unscrew and remove “A” frame to final drive unit fron

2000-2006 TOYOTA TUNDRA 2WD AND 4WD 6″ SUSPENSION SYSTEMS INSTALLATION MANUAL

download
FRONT INSTALLATION INSTRUCTIONS 1. On 4WD models only, remove grease cap, cotter pin and locking cap. (Illustration 1) While applying the brakes, loosen both Driver side and Passenger front axle nuts but do not remove. 2. Raise the vehicle. If working without a shop hoist, support vehicle with suitable safety jack stands. Put vehicle in gear, set emergency brake and block rear wheels, both in front and behind tires. Loosen front wheel lug nuts. Place floor jack under the lower control arm’s front crossmember and raise vehicle. Place safety jack stands under frame rails, behind front wheel wells, and lower the frame onto the stands. Once securely on jack stands remove floor jack. Remove front wheels. Illustration 1 7 RCD Suspension 619-588-4723 3. Place a jack under front lower a-arm. Remove lower nut from front shock mount. Next, locate the three nuts at the top of the front shock. (Illustration 2) Remove these nuts, lower the a-arm and remove front shock. Repeat on opposite side of vehicle. 4. Locate and remove the nut, retainer collar and cushion that attaches the Sway Bar end to the lower a-arms. (Illustration 3) Remove the two brackets that attach the Sway Bar to the frame. (Illustration 4) Stock Sway Bar can be discarded but make sure to keep original mounting brackets. 5. Detach bolt and brake line hose clamp from the front spindle. (Illustration 5) Next, remove the two bolts that attach the brake caliper to the front spindle. Remove the brake caliper and tie it up with safety wire. DO NOT LET IT HANG BY THE BRAKE LINE. Illustration 2 Illustration 3 Illustration 4 Illustration 5 8 RCD Suspension 619-588-4723 6. Remove rotor using snap ring pliers to remove inner snap ring. (Illustration 6) (Some models may not have snap ring and rotor can just be removed at this point) 7. Remove Cotter pin and loosen nut located on upper front ball joint. (Illustration 7) (on 4WD models use a strap to support the Front Drive Axle and keep it from resting at full bind) Using Ball joint puller, remove upper control arm from spindle. 8. Next, remove the cotter pin and nut located at the Tie Rod End on the Spindle. Using the Tie Rod Puller, disconnect the Tie Rod from the Spindle. (Illustration 8) 9. On 4WD models remove the axle nut. On ABS equipped vehicles, detach the ABS speed sensor from stock spindles. 10. Locate the four bolts attaching the Lower Ball Joint on the a-arm to the front spindle. (Illustration 9) Remove the bolts and take spindle off of vehicle. 11. Repeat steps 5 through 10 on opposite side of vehicle

Steering, Brake And Suspension Specialists Proportioning Valve Diagram

download
This diagram is the most common way to plumb a proportioning valve. In some cases, the right front line will be plugged off at the proportioning valve and the left front line will go to a “T” fitting. From the “T” fitting, the front lines then split off and go to the left and right wheels. Our proportioning valve has a warning light switch built in (this is not a stop light switch.) The warning light will detect any loss of pressure, for example, a leaky wheel cylinder. We recommend you wire this light into your system. Any two wire light socket will work. One wire goes to the accessory power and the other goes to the warning light. Our proportioning valves provide four functions: 1. Proportion pressure front and rear 2. 10 psi. residual check valve 3. Metering valve to apply pressure to the rear brakes before the front brakes 4. A brake warning light to detect a loss in pressure Proportioning Valve Plumbing Diagram: There are two proportioning valve lines that connect to the master cylinder provided in our kits. The first is a 90 degree bend with one leg longer than the other. This line must be oriented with the long leg connected into the front top hole of the proportioning valve and the short end in the front hole on the master cylinder. The second line has two 90 degree bends and has color coded fittings. The larger blue fitting goes into the back hole on the master cylinder and the smaller gold fitting goes into the back top hole on the proportion valve as shown in the diagram

2001 Subaru Legacy GT Sedan AWD F4-2.5L SOHC Steering and Suspension, Wheel Bearing, Service and Repair Manual

download
1. Remove knuckle. Refer to Steering and Suspension. 2. Using ST1 and ST2, remove hub from rear housing. 3. Remove back plate from rear housing. 4. Using a standard screwdriver, remove outer and inner oil seals. CAUTION: Use new oil seals. 5. Using flat bladed screwdriver, remove snap ring. 6. Using ST1 and ST2, remove bearing by pressing inner race. ST1 927430000 HOUSING STAND ST2 927440000 BEARING REMOVER CAUTION: * Do not remove bearing unless damaged. * Do not re-use bearing after removal. 7. Remove tone wheel bolts and remove tone wheel from hub (only vehicle equipped with ABS). 8. Using ST, press hub bolt out. ST 927080000 HUB STAND. CAUTION: Be careful not to hammer hub bolts. This may deform hub. INSPECTION Check the removed parts for wear and damage. If defective, replace with a new one. CAUTION: * If a bearing is faulty, replace it as the bearing set. * Be sure to replace oil seal at every overhaul. ASSEMBLE 1. Using ST, press new hub bolt into place. CAUTION: * Ensure hub bolt closely contacts hub. * Use a 12 mm (0.47 inch) hole in the ST to prevent hub bolt from tilting during installation.

2000 Audi A6 OIL PAN (A4 And A6) Removal And Installation Manual

download
OIL PAN(A4 & A6) Removal (Lower Pan- A4 & A6) 1. Disconnect negative battery cable. 2. Remove engine noise insulator (undercover). See Fig. 12 . Drain engine oil. 3. Unbolt left and right swaybar stabilizer bracket bolts (4) from mounting bracket. See Fig. 98 . Lower swaybar stabilizer not more than 10cm (3.94 INCHES) and secure with heavy wire. 4. If vehicle is equipped with automatic transmission, unbolt oil cooler pipe (line) bracket from right side oil pan. 5. Remove lower oil pan. To install oil pan (lower), see INSTALLATION (LOWER OIL PAN- A4 & A6) . Installation (Lower Oil Pan- A4 & A6) 1. Ensure oil pan surfaces are clean and dry. Remove residual sealant from oil pan, if necessary, with hand drill and plastic brush instead of a flat scrapper. See Fig. 99 . Install gasket. 2. Install 2 bolts diagonal to each other (to hold up pan). Install the rest of the bolts and hand tighten. 3. Starting at center and moving outward, tighten lower oil pan to upper oil pan bolts to 10 N.m (89 INCH lbs.). Tighten oil pan drain plug 30 N.m (22 ft. lbs.). Wait 30 minutes before filling with engine oil. Tighten all bolts to specification. See TORQUE SPECIFICATIONS . 4. To complete installation, reverse removal procedure. Fill and bleed cooling system. See COOLING SYSTEM BLEEDING . Removal (Upper Oil Pan- A4 & A6) 1. Disconnect negative battery cable. Remove oil dipstick. Unbolt oil dipstick tube at front of cylinder head. Remove oil dipstick tube. 2. Remove engine noise insulator (undercover). See Fig. 12 . Drain engine oil. 3. Move lock carrier into service position. See LOCK CARRIER . This will allow servicing of front engine components and facilitate removal of oil pan. 4. Open coolant expansion tank cap, drain cooling system at radiator. Open the coolant pump bearing housing drain plug. Located at bottom of block near transmission bell housing, drivers side of vehicle. See Fig. 32 – Fig. 33 . If vehicle is equipped with automatic transmission, unbolt oil cooler pipe (line) CAUTION: Wear eye protection NOTE: Obtain radio code before disconnecting battery. For help in identifying components and component locations, refer to illustrations Fig. 108 -Fig. 109 . NOTE: If engine is out of car, ensure oil pan is aligned with cylinder block on flywheel side. 2000 Audi A6 1998-02 ENGINES’ ’2.8L V6 30-Valve 2000 Audi A6 1998-02 ENGINES’ ’2.8L V6 30-Valve bracket from right side oil pan. 5. Position Engine Support (10-222A) with (10-222A/3) engine support adapter, or equivalent, on bolted flanges of fenders. Connect support bracket to front and rear engine lifting eyes. Lift up engine as far as possible. DO NOT use excessive force to raise engine. 6. Cut tie wraps and open bracket supporting starter wiring. See Fig. 97 . Disconnect electrical connection at starter.