t56 6 speed reverse lockout actuator

You search PDF repair manual about t56 6 speed reverse lockout actuator, if there are search results will appear below. If search results do not exist, please search by others keyword.



  t56 6 speed reverse lockout actuator Direct Download speed 5432 Kb/s

  t56 6 speed reverse lockout actuator Full Version speed 8172 Kb/s



1999 Jeep Grand Cherokee Limited AUTOMATIC TRANSMISSIONS Chrysler 45RFE Electronic Controls Repair Manual

0

Filed Under (Jeep Manuals) by admin on 11-07-2012

download
INTERNAL TCM Circuit Description The TCM is reporting internal errors. Diagnostic Procedure 1. Turn ignition switch to LOCK position. Remove transmission control relay. Measure resistance between ground and relay ground circuit (Black/Yellow wire) in relay connector. If resistance is greater than 5 ohms, repair open circuit. If resistance s not greater than 5 ohms, go to next step. 2. The TCM has an internal problem and must be replaced. P0715: INPUT SPEED SENSOR ERROR Circuit Description DTC P0715 will set if an excessive change in input RPM has been detected in any gear. Possible Causes * Intermittent wiring and connector problems. * Faulty input speed sensor. * Input speed sensor circuits shorted to ground, shorted to voltage, or open. * Faulty TCM. Diagnostic Procedure 1. Place gear selector in “P” position and start engine. Using scan tool, monitor input speed sensor value. If value is less than 400 RPM, go to next step. If value is not less than 400 RPM, go to step 9. 2. Turn ignition switch to LOCK position. Install Transmission Simulator (8333). Turn ignition on. Using transmission simulator, turn rotary knob to middle (1000/3000) position. Turn INPUT/OUTPUT switch on. Using scan tool, monitor input and output speed sensor values. If input speed sensor value is 2950- 3050 RPM and output speed sensor value is 950-1050 RPM, replace input speed sensor. If speed sensor values are not as specified, go to next step. 3. Turn ignition switch to LOCK position. Disconnect TCM harness connector. Remove transmission control relay. Using fused jumper wire, jumper fused B+ circuit (Red/White wire) and transmission relay output circuit (Red wire) together at relay connector. Turn ignition on. Measure voltage between ground and input speed sensor signal circuit (Red/Black wire) at TCM harness connector. If voltage is greater than 3 volts, repair circuit for short to voltage. If voltage is not greater than 3 volts, remove jumper wire, install relay and go to next step. 4. Turn ignition switch to LOCK position. Disconnect input speed sensor harness connector. Measure resistance of input speed sensor signal circuit (Red/Black wire) between TCM and input speed sensor. If resistance is greater than 5 ohms, repair open circuit. If resistance is not greater than 5 ohms, go to next step. 5. Measure resistance of input speed sensor ground circuit (Dark Blue/Black wire) between TCM and input

Related Content:

yhs-fh_lsonsw, kia rondo input speed sensor, How to remove back up sensor on 2012 explorer rear bumper, WHERE IS THE FUSE PANEL IN A 1986 TOYOTA PICKUP, where is the rpm sensor for a kia sedona, where is the transfer case speed sensor on a avalanche, asc spoiler sunroof wont close grand cherokee, nissan liberty gearbox, manual toyota lc200 pdf, replacing a input turbine speed sensor for 2004 mazda 3

2003 Mazda 6 V6-3.0L DOHC Airflow Mode Actuator Manual

0

Filed Under (Mazda Manuals) by admin on 03-05-2012

download
AIRFLOW MODE ACTUATOR INSPECTION Full-auto Air Conditioner 1. Connect battery positive voltage to terminal E or F and ground to terminal F or E of the airflow mode actuator. 2. Verify that the airflow mode actuator operates as shown. * If not as specified, replace the airflow mode actuator 3. Verify that the resistance between the terminals of the airflow mode actuator is as shown in the graph. * If not as specified, replace the airflow mode actuator. Manual Air Conditioner Operating inspection 1. Turn the fan switch to OFF. 2. Turn the mode dial to VENT. 3. Turn the ignition switch to ON position, (engine ON) 4. Turn the fan switch 4th position. 5. Turn the mode dial from VENT to DEFROSTER. 6. Verify that the airflow mode actuator moves smoothly. * If not as specified, inspect the airflow mode main link and sub link for clogging and deformity. * If the actuator cannot move at all, go to voltage inspection. Voltage inspection 1. Disconnect the airflow mode actuator connector. 2. Turn the ignition switch to ON position, (engine OFF) Zoom Sized for Print Zoom Sized for Print Zoom Sized for Print 3. Verify that the voltage between the terminals of airflow mode actuator (harness-side) is as shown in the table. * If not as specified, perform the harness inspection and mode switch inspection. (See CLIMATE CONTROL UNIT INSPECTION, Manual Air Conditioner.) * If as specified, replace the airflow mode actuator

Related Content:

2009 chevy impala cost repair actuator, how to reset air conditioner 03 silverado, 97 silverado mode actuator, ac door actuator motor 2009 f150, symptoms of bad valve timing actuator, how to replace a HVAC module 2002 chev silverado, how to change actuator in 2010 impala, how to replace blend door motors on a 2009 ford f150 lariat, how to change a A/C Actuator on a 2009 Impala, how to run rack on n14

1999-2006 Volkswagen A4 Engine Speed Sensor G28 Checking

0

Filed Under (Volkswagen Manuals) by admin on 31-01-2011

download
Special tools, testers and auxiliary items required Multimeter . Wiring diagram. Test requirements The Motronic Engine Control Module (ECM) J220 fuses OK. Battery voltage at least 12.5 volts. All electrical consumers such as, lights and rear window defroster, switched off. Vehicles with automatic transmission, shift selector lever into position “P” or “N” . A/C switched off. Ground (GND) connections between engine/transmission/chassis OK. Ignition switched off. Test procedure Perform a preliminary check to verify the customers complaint. Refer to Preliminary Check Start diagnosis The Engine Speed (RPM) Sensor G28 detects RPM and reference marks. Without an engine speed signal, the engine will not start. If the engine speed signal fails while the engine is running, the engine will stop immediately Function test Connect the scan tool. Switch the ignition on. Using the scan tool, check the engine speed: End diagnosis and switch ignition off. If the specified value was not obtained: Checking internal resistance Disconnect the gray Engine Speed (RPM) Sensor G28 electrical harness connector 7 arrow 7 . Using a multimeter , check the Engine Speed (RPM) Sensor G28 terminals 2 to 3 7 see insert 7 for resistance. Specified value: 0.7 to 1000 kOhm Check Engine Speed (RPM) Sensor G28 terminals 1 to 2 and 1 to 3 for short circuits. Specified value: ? (infinity) If any of the specified values are not obtained: Replace the Engine Speed (RPM) Sensor G28 . Refer to Engine Mechanical, Fuel Injection and Ignition 7 Repair Group 13 . If the specified values are obtained: Checking wiring If the manufacturers test box is being used. Perform the following step. Install the test box Adapter F/VAG1598 (68 Pin) VAG1598/22 . If the manufacturers test box is not being used. Perform the following step. Remove the Motronic Engine Control Module (ECM) J220 . Refer to Motronic Engine Control Module J220, Replacing .

Related Content:

G28 Engine Speed Sensor where to buy, g28 resistance value bvk engine, G28 Sensor VW

1993-2002 Volkswagen Golf, Jetta, GTI, Cabrio A/C controls and mechanical components service manual

0

Filed Under (Volkswagen Manuals) by admin on 09-07-2012

download
1 – . Dust and pollen filter Where applicable 2 – . Plenum cover Removing/installing – -”> 3 – Evaporator water drain valve Located behind bulkhead insulation Removing/installing Fig. 2 Removing and installing evaporator water drain valve 4 – . Heater core connections and vacuum hose guide 5 – . Fresh Air/Recirculating Flap Two-Way Valve N63 Valve open when voltage applied Vacuum hose layout Vacuum hose layout 6 – . Coolant Fan Control (FC) Control Module J293 With fuse Fuse Strip S88 (1993 m.y.) With fuses Coolant Fan Second and Third Speed Fuse S107 and Coolant Fan First Speed and A/C Clutch Fuse S108 (1994 m.y. micro ) Connector terminal identification: micro 09.93 Fig. 5 Connector terminal identification of Coolant Fan Control (FC) Control Module J293 ( 09.93) 10.93 micro Fig. 6 Connector terminal identification of Coolant Fan Control (FC) Control Module J293 (10.93 ) 7 – . Vacuum reservoir Insert vacuum hose 30 mm (1.2 in.) into reservoir Removing/installing Fig. 7 Removing and installing vacuum reservoir A/C and heating system components, engine compartment Vacuum hose Vacuum hose layout Vacuum hose layout 9 – . A/C Cut-Out Thermal Switch F163 and Third Speed Coolant Fan Control (FC) Thermal Switch F165 A/C Cut-Out Thermal Switch F163 only on vehicles with engine codes AAA, AAZ, ABA, ACC A/C Cut-Out Thermal Switch F163 switches A/C Clutch N25 off at high engine coolant temperature; OFF (switch open) above 119 degree C (246 degree F); ON (switch closed) below 112 degree C (234 degree F) Third Speed Coolant Fan Control (FC) Thermal Switch F165 only on vehicles with 3- speed coolant fan motor Third Speed Coolant Fan Control (FC) Thermal Switch F165 switches radiator coolant fan to 3rd speed as engine coolant temperature increases; 3rd speed ON (switch closed) above 112 degree C (234 degree F); OFF (switch open) below 108 degree C (226 degree F) Removing and installing (engine code AAA) Fig. 3 Removing and installing A/C Cut- Out Thermal Switch F163 and Third Speed Coolant Fan Control (FC) Thermal Switch F165 (2.8 liter VR6 engine code AAA) Removing and installing (engine code ABA) Fig. 4 Removing and installing A/C Cut- Out Thermal Switch F163 (2.0 liter engine code ABA) 10 – . Condenser* 11 – . Pressure relief valve*

Related Content:

02 Jetta Fan Control Module, 2002 lincoln ls cooling system diagram, fan fuse for 1995 chevy lumina, fan sensor vw beetle how to change, how to replAce mounting on evap canister on 2001 f150 to truck body, Mazda MPV Fan Control Module 2002

1995-1997 FORD EXPLORER TRANSFER CASE BINDING OR SHUDDER DIAGNOSTICS VEHICLES WITH 4.0L ENGINE SERVICE TIP

0

Filed Under (Ford Manuals) by admin on 20-01-2012

download
TRANSFER CASE BINDING OR SHUDDER DIAGNOSTICS VEHICLES WITH 4.0L ENGINE SERVICE TIP ISSUE to the Data Link Connector (DLC) underneath The diagnostic procedure for binding or shudder the steering wheel. Monitor for any Diagnostic from transfer case in slow, tight turns while in 4 Trouble Codes (DTCs) set by the transfer case Auto mode may be inaccurate for some vehicles. that could indicate incorrect speed sensor function. Codes could include, but are not ACTION limited to: Diagnose transfer case binding or shudder concerns using the following Diagnostic Procedure. •P1836 – Front propshaft sensor circuit failure •P1837 – Rear propshaft sensor circuit failure DIAGNOSTIC PROCEDURE •P1874 – Hall effect sensor power short circuit to battery 1997 EXPLORER •P1875 – Hall effect sensor power circuit 1. Test drive the vehicle in 4 Auto, 4 High and 4 failure Low. Evaluate the vehicle in each of these NOTE modes. The vehicle should bind in turns in both ADDITIONAL CODES COULD BE SET AS WELL. 4 High and 4 Low, but not in 4 Auto. The 4 PLEASE REFER TO THE APPROPRIATE YEAR High mode is intended for severe winter EXPLORER SERVICE MANUAL FOR COMPLETE weather or off-road driving only. It is not LISTING AND EXPLANATION. intended for use on dry or merely wet pavement. 3. If any of the DTCs in the above Step 2 are set, remove the corresponding speed sensor and 2. Verify the instrument panel has the proper 4X4 replace accordingly. Drive the vehicle to verify if selection label (Figure 1). Proceed to 1995-97 the shudder/binding has been eliminated. Send Explorer heading, Step 1. replaced speed sensor to the Ford Warranty 1995-97 EXPLORER Parts Return Center, Canton, MI. NOTE 4. Using NGS Tester, monitor the Parameter 4 AUTO IS THE FAR LEFT SWITCH POSITION Identification Display (PID) on the transfer case ON 1997 MODELS AND IS THE MIDDLE clutch duty cycle. If the 4 Auto mode reads POSITION ON 1996 MODELS. something higher than one (1), verify speed sensors have not set any Generic Electronic 1. If during test driving, the vehicle shudders or Module (GEM) DTCs and follow the speed binds in 4 Auto during slow forward or reverse sensor diagnostic procedure in the above Step parking lot maneuvers, proceed to Step 2. 2. Verify the following while checking PID: Mode Duty Cycle Indicator 4 Auto 0 or 1 4 High 13 4 Low 38 at 5 MPH 5. If the speed sensor circuits are functional, inspect for water contamination in the transfer case oil

Related Content:

1997 Ford Explorer Repair Manuals, 2011 Chevy Cruze P057c Code, ford explorer Front Axle Clunking, pid default parmameters for 2007 ford explorer, po57c

3406E Truck Engine Installation OR Removal Of The Speed/ Timing Sensor

0

Filed Under (More Manuals) by admin on 22-06-2012

download
1. Disconnect the speed/timing connector “P9/J9″ (2) . Inspect the connector for the following conditions. * Corrosion * Bent pins * Missing pins * Damaged sockets * Mismating * Broken wires 2. Remove the Speed/timing sensor (1) from the front gear cover. 3. Examine the plastic end of the sensor for signs of wear or contaminants such as metal filings. The plastic end of the speed/timing sensor should have no contaminants and should show no wear (greater than 0.051 mm (0.0020 inch) from the face) . 4. Use a screwdriver to carefully pry the plastic sensor end to the fully extended position (approximately 4.775 mm (0.1880 inch) beyond the metal housing of the sensor). 5. Gently push in on the plastic end of the sensor. The plastic end should be firm. The plastic end should resist movement in the retract direction. If there is no resistance replace the sensor 6. Remove the two bolts (3) and remove the cover (5) from the flywheel housing. This hole is used for engine turning. 7. Put one bolt (3) in the timing bolt location (4) . The timing bolt location is approximately 127 mm to 152 mm (5 inch to 6 inch) above the hole in the flywheel housing for engine turning. I 8. Use 9S-9082 Engine Turning Tool (6) and a 1/2 inch drive ratchet wrench to turn the engine flywheel in the direction of normal engine rotation. The normal engine rotation is in a counterclockwise direction when viewed from the flywheel end. Turn the engine flywheel until the timing bolt engages with the threaded hole in the flywheel. Note: Visually check the location of the tooth on the wheel on which the speed/timing sensor is to be positioned. The end of the sensor must be in alignment with a tooth on the wheel and not in alignment with the valley of the wheel. Note: The No. 1 piston must be at either top center of the compression stroke or at top center of the exhaust stroke. 9. Inspect the speed/timing sensor before installation. Use steps 3 through step 6 to inspect the sensor. 10. If the sensor end is not fully extended, use a screwdriver to carefully pry the plastic sensor end to the fully EXTENDED position approximately 4.775 mm (0.1880 inch) beyond the metal housing of the sensor.

Related Content:

4efe maf sensor, 4L60E VSS Sensor Location, b0091 front end sensor 3 location, cat 3406 e engine sensor locations, front end connector sensor 1

2005 Ford Lincoln LS Climate Control System Manual

0

Filed Under (Ford Manuals) by admin on 21-05-2011

download
When PANEL is selected: z The Recirc request button is enabled. If the Recirc request button is selected (indicator ON), the air inlet door actuator positions the air inlet door to close off outside air from entering the passenger compartment. If the Recirc request button is not selected (indicator OFF), the air inlet door actuator positions the air inlet door to admit only outside air into the passenger compartment. z The panel door actuator positions the panel door in the OPEN position and the floor door and defrost door actuators position the floor door and defrost door in the CLOSED position, directing airflow to the instrument panel A/C registers. z The dual coolant control valve is automatically controlled by the DATC module based on the temperature setting(s). z The A/C request button is enabled. When the A/C request button is selected (indicator ON), the A/C compressor will operate if the outside air temperature is above approximately 2° C (35°F). When the A/C request button is not selected (indicator OFF), the A/C compressor will not operate and the air cannot be cooled below the outside temperature. z The blower motor is ON. PANEL/FLOOR When PANEL/FLOOR is selected: z The Recirc request button is enabled. If the Recirc request button is selected (indicator ON), the air inlet door actuator positions the air inlet door to close off outside air from entering the passenger compartment. If the Recirc request button is not selected (indicator OFF), the air inlet door actuator positions the air inlet door to admit only outside air into the passenger compartment. z The panel door and floor door actuators position the panel door and floor door in the OPEN position and the defrost door actuator positions the defrost door in the CLOSED position, directing airflow to the instrument panel A/C registers and the floor duct. z The dual coolant control valve is automatically controlled by the DATC module based on the temperature setting(s). z The A/C request button is enabled. When the A/C request button is selected (indicator ON), the A/C compressor will operate if the outside air temperature is above approximately 2° C (35°F). When the A/C request button is not selected (indicator OFF), the A/C compressor will not operate and the air cannot be cooled below the outside temperature. z The blower motor is ON. FLOOR

Related Content:

2007 impala recirc actuator repair, 2009 impala inside air to outa-side air, ford fusion gas tank button, gmc2004 1500 bland airdoar, repair for 2008 impala fresh air door

1999 Chrysler Truck Town And Country Blend Door Actuator REMOVAL And INSTALLATION MANUAL

0

Filed Under (Chrysler Manuals) by admin on 29-01-2012

download
REMOVAL The air conditioning system can be equipped with either a standard, single blend- air door actuator, or it can be equipped with dual actuators. The dual system has separate blend-air controls. This allows for separate control of the driver’s side air, and the passenger side air. 1. Remove the lower left side steering column cover. Refer to Instrument Panel and Systems. Side View Of HVAC With Actuators Zoom Sized for Print ABS Control Module 2. Remove ABS control module. 3. Remove blend-air actuator connector. 4. Remove blend-air actuator. INSTALLATION 1. For installation, reverse the above procedures. 2. Perform the HVAC Control Calibration Diagnostic and Cooldown test. Repeating the test is necessary to clear the fault codes

Related Content:

1999 Town and Country Radiator Replacement, 97 town and country steering column removal

1991-1992 Toyota MR2 Turbo, 1990-1992 Toyota Celica All Trac ECU Pinout Diagram

0

Filed Under (Toyota Manuals) by admin on 21-09-2011

download
Connector A Pin # Name Function Signal Type A13 Power Ground Chassis ground Ground A14 Power Ground Chassis ground Ground A20 Ignition Control Module Engine speed Speed A26 Power Ground Chassis ground Ground Connector B Pin # Name Function Signal Type B3 Intake Air Temperature Sensor Air temperature sensor signal Analog B4 Engine Coolant Temperature Sensor Engine coolant temperature sensor signal Analog B5 Knock Sensor Engine knock sensor Knock, Audio B6 Primary 02 Sensor Primary oxygen sensor signal Analog B11 Throttle Position Sensor Throttle position sensor signal Analog B13 MAP Sensor Manifold absolute pressure sensor signal Map min: 4.89 Map max: 1.09 Analog Connector D Pin # Name Function Signal Type D1 Voltage Back Up Permanent 12V Power D4 Brake Switch Brake switch signal Analog D9 Vehicle Speed Sensor Vehicle speed sensor signal Speed D12 Power Source 12V switched Power D13 Power Source 12V switched Power

1991-1992 Toyota MR2 Turbo 1990-1992 Toyota Celica All Trac ECU Pinout Diagram

0

Filed Under (Toyota Manuals) by admin on 18-04-2012

download
A13 Power Ground Chassis ground Ground A14 Power Ground Chassis ground Ground A20 Ignition Control Module Engine speed Speed A26 Power Ground Chassis ground Ground Connector B Pin # Name Function Signal Type B3 Intake Air Temperature Sensor Air temperature sensor signal Analog B4 Engine Coolant Temperature Sensor Engine coolant temperature sensor signal Analog B5 Knock Sensor Engine knock sensor Knock, Audio B6 Primary 02 Sensor Primary oxygen sensor signal Analog B11 Throttle Position Sensor Throttle position sensor signal Analog B13 MAP Sensor Manifold absolute pressure sensor signal Map min: 4.89 Map max: 1.09 Analog Connector D Pin # Name Function Signal Type D1 Voltage Back Up Permanent 12V Power D4 Brake Switch Brake switch signal Analog D9 Vehicle Speed Sensor Vehicle speed sensor signal Speed D12 Power Source 12V switched Power D13 Power Source 12V switched

Related Content:

change knock sensor 2005 chevy avalanche, diogram of knock sensor on 1999 lumina, where is the air temp sensor on 2001 toyota celica

Related Content:

yhs-fh_lsonsw, kia rondo input speed sensor, How to remove back up sensor on 2012 explorer rear bumper, WHERE IS THE FUSE PANEL IN A 1986 TOYOTA PICKUP, where is the rpm sensor for a kia sedona, where is the transfer case speed sensor on a avalanche, asc spoiler sunroof wont close grand cherokee, nissan liberty gearbox, manual toyota lc200 pdf, replacing a input turbine speed sensor for 2004 mazda 3