thermistor sensor gas tank low level

You search PDF repair manual about thermistor sensor gas tank low level, if there are search results will appear below. If search results do not exist, please search by others keyword.



  thermistor sensor gas tank low level Direct Download speed 5432 Kb/s

  thermistor sensor gas tank low level Full Version speed 8172 Kb/s



Low Engine Coolant Level Indicator Always On (Diagnose Low Coolant Level System Operation/Check Sensor for Oil Contamination)

0

Filed Under (More Manuals) by admin on 19-05-2012

download
2000-2002 Buick Century, Regal 2000-2001 Chevrolet Lumina 2000-2002 Chevrolet Impala, Monte Carlo 2000-2002 Pontiac Grand Prix 2000-2002 Oldsmobile Intrigue 1. Verify that the coolant is at proper level in the radiator and the coolant recovery bottle. If the coolant is low, add proper amount of 50/50 water and DEX-COOL® mixture. If the low coolant light operates properly, diagnose the cooling system for loss of coolant as outlined in SI. DO NOT proceed further with this bulletin. 2. Remove the low coolant level sensor. Refer to Coolant Level Module Replacement in the Engine Cooling sub-section. 3. With the key on, the engine off and the coolant level sensor disconnected from the vehicle wiring harness, observe the low coolant light: Subject: Low Engine Coolant Level Indicator Always On (Diagnose Low Coolant Level System Operation/Check Sensor for Oil Contamination) Models: 2000-2002 Buick Century, Regal 2000-2001 Chevrolet Lumina 2000-2002 Chevrolet Impala, Monte Carlo 2000-2002 Pontiac Grand Prix 2000-2002 Oldsmobile Intrigue • Light is on — Chassis wiring or instrument cluster concern. Follow the appropriate diagnostic information in SI. • 4. With the key off, connect the coolant level sensor into the vehicle’s wiring harness. Connect a ground wire (1) to the battery negative terminal. Using a sharp probe (3) attached to the ground wire, ground the coolant sensor probe (2) as shown in the illustration. Make sure a good contact is made. With the key on and the engine off, observe the low coolant light for at least 15 seconds. 5. Using a small wire brush or emery cloth, polish the low coolant level sensor probe to remove any film or oxidation. The probe should be a bright brass color when finished. Use Brake Parts Cleaner to flush removed deposits from the low coolant sensor probe. Reinstall the low coolant sensor into the vehicle and proceed to Step 6. 6. Flush the cooling system and install new DEX-COOL® mixture as outlined in the SI. Check the vehicle’s warranty history to determine if any engine gasket had recently been changed. If there has not been a recent gasket replacement, locate and repair the source of the engine oil contamination

Related Content:

low coolant 01 suburban, Low coolant light olds intrigue, how to check radiator fluid level pontiac grand prix, replace low coolent sencor on 1997 chevy lumnia, Low Coolant Sensor Location in olsdmobile silluette, 2002 Chevrolet Impala see a diagram of the a/c controls, 2002 chevy avalanche instrument cluster wiring, p0446 2002 monte carlo, 2002 mercury sable cooling system, evap sensor on 2002 suburban

1999 Saturn SL1 L4-1.9L SOHC VIN 8 Engine – Driveability Concerns/ Cooling System DTC’s Set

0

Filed Under (Saturn Manuals) by admin on 19-05-2012

download
1. Disconnect engine coolant temperature sensor electrical connector and inspect sensor and connector terminals for corrosion and/or evidence of engine coolant. ^If terminals are corroded or if there is evidence of engine coolant proceed to step 4. ^If terminals are not corroded and there is no evidence of engine coolant, reconnect the electrical connector and continue to next step. 2. Perform one or both of the following checks to determine whether the engine coolant temperature sensor is providing the correct temperature indication. If engine coolant temperature sensor reading does not pass either of the above tests, continue with next step. ^If engine is at ambient temperature (vehicle has been sitting overnight or not started for several hours), use a Scan tool to compare the inlet air temperature ( IAT ) to the engine coolant temperature ( ECT ). These two readings should be within 2°C (4°F) of each other. ^If engine is at operating temperature, install a thermometer in the coolant recovery reservoir. With the engine running and A/C off, use a Scan tool to compare the engine coolant temperature sensor reading to the thermometer reading. These two readings should be within 8°C (15°F) of each other If engine coolant temperature sensor reading passes both of the tests above, refer to appropriate symptom diagnostic chart in the Engine/Emissions Controls Section of applicable Engine Service Manual. 3. Turn ignition off. 4Remove coolant surge tank cap. 5. Drain at least 1.9 L (2 Qt.) of engine coolant from the cooling system by opening radiator drain valve or removing engine drain plug. Collect engine coolant in a container. 6. Disconnect engine coolant temperature sensor electrical connector. 7. Remove engine coolant temperature sensor from cylinder head. 8. Obtain replacement engine coolant temperature sensor (P/N 21025106). 9. Use appropriate tap to clean sensor mounting hole of any thread sealant residue. 10. Install engine coolant temperature sensor in cylinder head. Torque: Engine Coolant Temperature Sensor: 8 Nm (71 in-lbs) 11. Inspect harness connector terminals for corrosion and/or evidence of engine coolant. If harness connector terminals are corroded or there is evidence of engine coolant, the harness connector must be replaced with new connector (P/N 12117087-includes: connector, terminals, wires, and splice sleeves). 12. Connect engine coolant temperature sensor connector. 13. Transfer engine coolant drained in step 5 into coolant surge tank. If necessary fill coolant surge tank to the FULL COLD range with 50/50 solution of correct type of antifreeze and clean water. 14. Start engine and check for leaks. 15. Run engine until upper radiator hose is hot, then add additional coolant if needed to bring the level to the FULL COLD level (1991-early 1997) or within the Min./Max. cold range (late l997-2001). 16. Install coolant surge tank cap.

Related Content:

yhs-sgm_fb, wiring diagram for 2005 kia sedona engine cooling fan temperature sensor, crank sensor location on 6 7 power stroke, bye pass c15 timming sensor, replacing s radiator 2001 silhouette oldsmobile, location of air temp sensor on 2001 toyota celica, How to fix a gas gauge 2005 impala you tube, how to drain radiator on 2007 ford fusion 2 3 L, 2001 mitsubishi montero limited head gasket repair procedure pdf download, how many oxygen sensors on 5 4 V8 triton engine

1996 Ford Taurus Camshaft Position Sensor removal and installation manual

0

Filed Under (Ford Manuals) by admin on 16-06-2012

download
REMOVAL CAUTION: Prior to removal of the Camshaft Position (CMP) sensor, set cylinder No.1 to zero degrees Top Dead Center (TDC) of compression stroke. Then note the position of the CMP sensor electrical connector. The installation procedure requires that the connector be located in the same position. 1. Disconnect battery ground cable. NOTE: When the battery has been disconnected and reconnected, some abnormal drive symptoms may occur while the Powertrain Control Module (PCM) relearns its adaptive strategy. The vehicle may need to be driven 16 km (10 miles) or more to relearn the strategy. 2. Disconnect engine control sensor wiring connector from CMP sensor. 3. Remove retaining screws and CMP sensor from sensor housing. 4. If removing CMP sensor housing from the cylinder block, proceed with Removal Step 5. If not removing sensor housing, proceed to installation Step 6. 5. Remove hold-down clamp (bolt and washer assembly) . 6. Remove CMP sensor housing from cylinder block INSTALLATION CAUTION : A special service tool such as Syncro Positioning Tool T95T-12200-A must be obtained prior to installation of the replacement CMP sensor. Failure to follow this procedure will result in improper sensor alignment. This will result in the fuel system being out of time with the engine, possibly causing engine damage. 1. Attach Syncro Positioning Tool T95T-12200-A as follows: a. Engage CMP sensor housing vane into the radial slot of the tool. b. Rotate tool on CMP sensor housing until tool boss engages notch in sensor housing. 2. Pre-lubricate synchronizer gear with engine oil meeting Ford specification ESE-M2C123-A prior to assembly. 3. Install sensor housing so that drive gear engagement occurs when arrow on ocator tool is pointed approximately 75 degrees counterclockwise from the rear face of the cylinder block. This step will locate CMP sensor electrical connector in the pre-removal position. 4. Rotate Syncro Positioning Tool T95T-12200-A clockwise slightly. This will engage oil pump intermediate shaft. Push downward while adjusting Syncro Positioning Tool T95T-12200-A until the Syncro Gear engages the camshaft gear. 5. When synchronizer flange is fully seated against block, the installation tool should be facing counterclockwise of engine centerline approximately 33 to 45 degrees. 6. Install hold-down clamp (washer and bolt) and tighten bolt to 19-30 Nm (14- 22 lb ft)

Related Content:

2003 explorer impact sensor, howtoinstallnewairbagsenscoron2004chevy1500pickuptruck, how to change 2010 hhr cam sensor, cam timing sensor 2006 nissan frontier, 2007 toyota tundra camshaft position sensor removal, 2005 Tahoe Repair Manual PDF, Is there a resister on a 2008 ford 5 4 triton, 2005 chevy trailblazer camshaft position sensor install, 2004 nissan quest o2 sensor, how much to repair cam timing sensor in nissan frontier

2000 Ford Pickup F250 Super Duty TEST DE: EXHAUST BACKPRESSURE (EBP) SENSOR

0

Filed Under (Ford Manuals) by admin on 10-01-2012

download
DTC P0470 This DTC indicates PCM detected EBP sensor malfunction during KOEO ON-DEMAND SELF-TEST. Possible causes for this DTC are: Faulty EBP Sensor • Open Or Shorted Circuit • Faulty PCM • Ensure scan tool is connected to Data Link Connector (DLC). Using scan tool, select EBP PID from PID/DATA monitor menu. If EBP reading is less than 18.5 psi, clear DTCs. Repeat KOEO ON-DEMAND SELF-TEST . If DTC is still present, replace PCM. If EBP reading is 18.5 psi or more, go to next step. 2) Check Signal Ground Circuit Turn ignition off. Disconnect EBP sensor connector. Sensor is located on top front of engine. Inspect for damaged pins, corrosion and loose wires. Repair as necessary. Measure resistance between ground and Gray/Red wire at EBP sensor wiring harness connector. See Fig. 11 . If resistance is less than 5 ohms, replace EBP sensor. If resistance is 5 ohms or more, locate and repair open circuit in Gray/Red wire. 3) Continuous DTC P0470 This DTC indicates PCM detected a EBP sensor malfunction during normal driving conditions. Possible causes for this DTC are: Faulty EBP Sensor • Faulty Connection • Faulty PCM • Ensure scan tool is connected to Data Link Connector (DLC). Using scan tool, select EBP PID from PID/DATA monitor menu. While observing EBP PID, wiggle and bend small sections of wiring harness starting at EBP sensor connector and working toward PCM. If EBP reading fluctuates, isolate fault and repair as necessary. If reading does not fluctuate, go to next step. 4) Check Connector Disconnect EBP sensor connector. Sensor is located on top front of engine. Disconnect PCM 104-pin connector. Inspect connectors for damaged pins, corrosion and loose wires. Repair as necessary. Clear DTCs and repeat QUICK TEST . If both connectors are okay, no problem is indicted at this time. 5) DTC P0471 This DTC indicates PCM detected an EBP sensor malfunction during normal driving conditions and with EBP sensor enabled. Possible causes for this DTC are: Faulty EBP Sensor. • Plugged Or Restricted Sensor Supply Tube • Damaged Exhaust Pressure Regulator (EPR) Linkage Or Butterfly Damage • Faulty PCM • Perform KOER ON-DEMAND SELF-TEST . If any DTCs are present, repair fault(s) before continuing with this test. Using scan tool, select EBP PID from PID/DATA monitor menu. Road test vehicle performing hard accelerations while monitoring EBP PID. If EBP reading increases to more than 25 psi with EBP sensor on, no problem is indicated at this time. If EBP reading does not increase to more than 25 psi, go to next step

Related Content:

2007 nissan frontier camshaft position sensor location, Chevy Traverse Bank 2, 2000 Infiniti Q45 Problems, how to check oil in front crank case 2005 tahoe, 02 sensor problems 2010 prius, where is the heat sensor on a 2005 chevy impala?, o2 sensor bank 1 tundra, location of front heated exhaust oxygen sensor Saturn SL two 2002, locate 2011 traverse coolant temperature sensor, install cam sensor kia 05 sedona

1991-1992 Toyota MR2 Turbo 1990-1992 Toyota Celica All Trac ECU Pinout Diagram

0

Filed Under (Toyota Manuals) by admin on 18-04-2012

download
A13 Power Ground Chassis ground Ground A14 Power Ground Chassis ground Ground A20 Ignition Control Module Engine speed Speed A26 Power Ground Chassis ground Ground Connector B Pin # Name Function Signal Type B3 Intake Air Temperature Sensor Air temperature sensor signal Analog B4 Engine Coolant Temperature Sensor Engine coolant temperature sensor signal Analog B5 Knock Sensor Engine knock sensor Knock, Audio B6 Primary 02 Sensor Primary oxygen sensor signal Analog B11 Throttle Position Sensor Throttle position sensor signal Analog B13 MAP Sensor Manifold absolute pressure sensor signal Map min: 4.89 Map max: 1.09 Analog Connector D Pin # Name Function Signal Type D1 Voltage Back Up Permanent 12V Power D4 Brake Switch Brake switch signal Analog D9 Vehicle Speed Sensor Vehicle speed sensor signal Speed D12 Power Source 12V switched Power D13 Power Source 12V switched

Related Content:

change knock sensor 2005 chevy avalanche, diogram of knock sensor on 1999 lumina, where is the air temp sensor on 2001 toyota celica

1999 Jeep Grand Cherokee Limited AUTOMATIC TRANSMISSIONS Chrysler 45RFE Electronic Controls Repair Manual

0

Filed Under (Jeep Manuals) by admin on 11-07-2012

download
INTERNAL TCM Circuit Description The TCM is reporting internal errors. Diagnostic Procedure 1. Turn ignition switch to LOCK position. Remove transmission control relay. Measure resistance between ground and relay ground circuit (Black/Yellow wire) in relay connector. If resistance is greater than 5 ohms, repair open circuit. If resistance s not greater than 5 ohms, go to next step. 2. The TCM has an internal problem and must be replaced. P0715: INPUT SPEED SENSOR ERROR Circuit Description DTC P0715 will set if an excessive change in input RPM has been detected in any gear. Possible Causes * Intermittent wiring and connector problems. * Faulty input speed sensor. * Input speed sensor circuits shorted to ground, shorted to voltage, or open. * Faulty TCM. Diagnostic Procedure 1. Place gear selector in “P” position and start engine. Using scan tool, monitor input speed sensor value. If value is less than 400 RPM, go to next step. If value is not less than 400 RPM, go to step 9. 2. Turn ignition switch to LOCK position. Install Transmission Simulator (8333). Turn ignition on. Using transmission simulator, turn rotary knob to middle (1000/3000) position. Turn INPUT/OUTPUT switch on. Using scan tool, monitor input and output speed sensor values. If input speed sensor value is 2950- 3050 RPM and output speed sensor value is 950-1050 RPM, replace input speed sensor. If speed sensor values are not as specified, go to next step. 3. Turn ignition switch to LOCK position. Disconnect TCM harness connector. Remove transmission control relay. Using fused jumper wire, jumper fused B+ circuit (Red/White wire) and transmission relay output circuit (Red wire) together at relay connector. Turn ignition on. Measure voltage between ground and input speed sensor signal circuit (Red/Black wire) at TCM harness connector. If voltage is greater than 3 volts, repair circuit for short to voltage. If voltage is not greater than 3 volts, remove jumper wire, install relay and go to next step. 4. Turn ignition switch to LOCK position. Disconnect input speed sensor harness connector. Measure resistance of input speed sensor signal circuit (Red/Black wire) between TCM and input speed sensor. If resistance is greater than 5 ohms, repair open circuit. If resistance is not greater than 5 ohms, go to next step. 5. Measure resistance of input speed sensor ground circuit (Dark Blue/Black wire) between TCM and input

Related Content:

yhs-fh_lsonsw, kia rondo input speed sensor, How to remove back up sensor on 2012 explorer rear bumper, WHERE IS THE FUSE PANEL IN A 1986 TOYOTA PICKUP, where is the rpm sensor for a kia sedona, where is the transfer case speed sensor on a avalanche, asc spoiler sunroof wont close grand cherokee, nissan liberty gearbox, manual toyota lc200 pdf, replacing a input turbine speed sensor for 2004 mazda 3

3406E Truck Engine Installation OR Removal Of The Speed/ Timing Sensor

0

Filed Under (More Manuals) by admin on 22-06-2012

download
1. Disconnect the speed/timing connector “P9/J9″ (2) . Inspect the connector for the following conditions. * Corrosion * Bent pins * Missing pins * Damaged sockets * Mismating * Broken wires 2. Remove the Speed/timing sensor (1) from the front gear cover. 3. Examine the plastic end of the sensor for signs of wear or contaminants such as metal filings. The plastic end of the speed/timing sensor should have no contaminants and should show no wear (greater than 0.051 mm (0.0020 inch) from the face) . 4. Use a screwdriver to carefully pry the plastic sensor end to the fully extended position (approximately 4.775 mm (0.1880 inch) beyond the metal housing of the sensor). 5. Gently push in on the plastic end of the sensor. The plastic end should be firm. The plastic end should resist movement in the retract direction. If there is no resistance replace the sensor 6. Remove the two bolts (3) and remove the cover (5) from the flywheel housing. This hole is used for engine turning. 7. Put one bolt (3) in the timing bolt location (4) . The timing bolt location is approximately 127 mm to 152 mm (5 inch to 6 inch) above the hole in the flywheel housing for engine turning. I 8. Use 9S-9082 Engine Turning Tool (6) and a 1/2 inch drive ratchet wrench to turn the engine flywheel in the direction of normal engine rotation. The normal engine rotation is in a counterclockwise direction when viewed from the flywheel end. Turn the engine flywheel until the timing bolt engages with the threaded hole in the flywheel. Note: Visually check the location of the tooth on the wheel on which the speed/timing sensor is to be positioned. The end of the sensor must be in alignment with a tooth on the wheel and not in alignment with the valley of the wheel. Note: The No. 1 piston must be at either top center of the compression stroke or at top center of the exhaust stroke. 9. Inspect the speed/timing sensor before installation. Use steps 3 through step 6 to inspect the sensor. 10. If the sensor end is not fully extended, use a screwdriver to carefully pry the plastic sensor end to the fully EXTENDED position approximately 4.775 mm (0.1880 inch) beyond the metal housing of the sensor.

Related Content:

b0091 front end sensor 3 location, cat 3406 e engine sensor locations

1991-1992 Toyota MR2 Turbo, 1990-1992 Toyota Celica All Trac ECU Pinout Diagram

0

Filed Under (Toyota Manuals) by admin on 21-09-2011

download
Connector A Pin # Name Function Signal Type A13 Power Ground Chassis ground Ground A14 Power Ground Chassis ground Ground A20 Ignition Control Module Engine speed Speed A26 Power Ground Chassis ground Ground Connector B Pin # Name Function Signal Type B3 Intake Air Temperature Sensor Air temperature sensor signal Analog B4 Engine Coolant Temperature Sensor Engine coolant temperature sensor signal Analog B5 Knock Sensor Engine knock sensor Knock, Audio B6 Primary 02 Sensor Primary oxygen sensor signal Analog B11 Throttle Position Sensor Throttle position sensor signal Analog B13 MAP Sensor Manifold absolute pressure sensor signal Map min: 4.89 Map max: 1.09 Analog Connector D Pin # Name Function Signal Type D1 Voltage Back Up Permanent 12V Power D4 Brake Switch Brake switch signal Analog D9 Vehicle Speed Sensor Vehicle speed sensor signal Speed D12 Power Source 12V switched Power D13 Power Source 12V switched Power

1996 Ford Taurus Service and Repair Manual

0

Filed Under (Ford Manuals) by admin on 01-02-2012

download
REMOVAL CAUTION: Prior to removal of the Camshaft Position (CMP) sensor, set cylinder No.1 to zero degrees Top Dead Center (TDC) of compression stroke. Then note the position of the CMP sensor electrical connector. The installation procedure requires that the connector be located in the same position. 1. Disconnect battery ground cable. NOTE: When the battery has been disconnected and reconnected, some abnormal drive symptoms may occur while the Powertrain Control Module (PCM) relearns its adaptive strategy. The vehicle may need to be driven 16 km (10 miles) or more to relearn the strategy. 2. Disconnect engine control sensor wiring connector from CMP sensor. 3. Remove retaining screws and CMP sensor from sensor housing. 4. If removing CMP sensor housing from the cylinder block, proceed with Removal Step 5. If not removing sensor housing, proceed to installation Step 6. 5. Remove hold-down clamp (bolt and washer assembly) . 6. Remove CMP sensor housing from cylinder block INSTALLATION CAUTION : A special service tool such as Syncro Positioning Tool T95T-12200-A must be obtained prior to installation of the replacement CMP sensor. Failure to follow this procedure will result in improper sensor alignment. This will result in the fuel system being out of time with the engine, possibly causing engine damage. 1. Attach Syncro Positioning Tool T95T-12200-A as follows: a. Engage CMP sensor housing vane into the radial slot of the tool. b. Rotate tool on CMP sensor housing until tool boss engages notch in sensor housing. 2. Pre-lubricate synchronizer gear with engine oil meeting Ford specification ESE-M2C123-A prior to assembly. 3. Install sensor housing so that drive gear engagement occurs when arrow on

Related Content:

1996 ford taurus repair manual pdf free

4L60-E Automatic Transmission/Torque Converter Clutch (TCC) Shudder, Water in Transmission (Repair Transmission and Replace Transmission Filler Tube, Level Indicator and Seal)4L60-E Automatic Transmission/Torque Converter Clutch (TCC) Shudder, Water in Transmission (Repair Transmission and Replace Transmission Filler Tube, Level Indicator and Seal) Transmission Repair

0

Filed Under (More Manuals) by admin on 08-01-2012

download
Transmission Repair 1. Remove the transmission. Refer to the appropriate SI procedure. 2. Disassemble and inspect the transmission. Refer to Unit Repair Automatic Transmission – 4L60-E/4L65-E. Important: Subject: 4L60-E Automatic Transmission/Torque Converter Clutch (TCC) Shudder, Water in Transmission (Repair Transmission and Replace Transmission Filler Tube, Level Indicator and Seal) Models: 2004-2005 Buick Rainier 2003-2005 Chevrolet TrailBlazer Models 2003-2005 GMC Envoy Models 2003-2004 Oldsmobile Bravada 2005 Saab 9-7X with 4.2L In-Line 6 Cylinder Engine (VIN S — RPO LL8) • Visible rust on the transmission fluid level indicator. • Visible water in the oil pan. • A milky white substance inside the pan area. • Spacer plate gaskets that appear to be glued to the spacer plate, valve body or case. • Rust on internal transmission iron/steel components. • Remove the surge tank cap and examine the coolant for signs of contamination with transmission fluid (the coolant will have a milky, not clear appearance). • If the coolant has a normal, clear appearance, the radiator should not be replaced. • The cooler can also be tested by following the Coolant System Leak Test procedure (SI Document ID# 877442). Do NOT replace a radiator without verifying that the transmission oil cooler is leaking. If water or coolant is found in the transmission, the following components MUST be replaced. Replace the Transmission Fluid Filler Tube, Seal and Fluid Level Indicator WITH the transmission REMOVED from vehicle. 1. Remove the transmission fluid filler tube from the transmission. 2. Replace the transmission fill tube seal, P/N 1259475. 3. Replace the transmission fill tube, P/N 15000220, following the appropriate SI Document for Transmission Installation. 4. Replace the transmission fluid level indicator, P/N 15069769 when appropriate during the transmission installation. Replace the Transmission Fluid Filler Tube, Seal and Fluid Level Indicator with the transmission in the vehicle. 1. Remove the air cleaner outlet duct. Refer to Air Cleaner Element Replacement (SI Document ID# 1364496). 2. Remove the transmission fluid level indicator from the filler tube. 3. Remove the filler tube nut (2) located on the right side of the engine. 4. Remove the filler tube from the vehicle. Tip It is necessary to remove the two A/C line (suction line / low side of muffler hose) retainers and reposition • Replace all of the rubber type seals. • Replace all of the composition-faced clutch plate assemblies including the band. • Replace all of the nylon parts (Thrust Washers). • Replace the torque converter. • Thoroughly clean and rebuild the transmission, using new gaskets and oil filter. • Flush and flow check the transmission oil cooler using J 45096. Refer to Corporate Bulletin Number 02-07-30- 052C or newer – Automatic Transmission Oil Cooler Flush and Flow Test Essential Tool J 45096 TransFlow .
the A/C line to allow proper clearance for installation of the new transmission fluid fill tube. 5. Remove the A/C line at the oil level indicator tube bracket nut. 6. Remove the A/C bracket bolt from the engine lift hook. 7. Reposition the A/C line upward. 8. Install the new transmission filler tube, P/N 15000220, into position but NOT into the transmission at this time. 9. Raise the vehicle. Refer to Lifting and Jacking the Vehicle in General Information (SI Document ID# 744862). 10. Remove the two bolts securing the transmission heat shield to the transmission. 11. Remove the transmission heat shield from the transmission. 12. Remove the old filler tube seal from the transmission case. 13. Install a new seal, P/N 1259475 into the transmission case. 14. Position the new transmission filler tube into the transmission seal. 15. Install the transmission heat shield to the transmission. 16. Install the two bolts securing the transmission heat shield to the transmission. Tighten Tighten the bolts to 17 N·m (13 lb ft). 17. Lower the vehicle. 18. Install the nut securing the filler tube to the stud. Tighten Tighten the nut to 10 N·m (89 lb in). 19. Reposition the A/C line into place. 20. Install the A/C line bracket to the oil level indicator tube stud and secure the bracket with the nut. 21. Install the A/C line bracket to the engine lift bracket and secure the A/C bracket with the bolt

Related Content:

yhs-lavasoft, 2011 crv engine whine, automatic transmission adjustments for 1997 yuko, how to check tranmission fluid on 2012 kia sedona, 2005 explorer transmission exploded view, 2003 trailblazer torque converter removal, gm 4l60e band adjustment screws, 1997 e450 power stroke trans mount parking brake, manual pdf transmicion automatica ram 2001, transmission module for 1999 ford ranger xlt

Related Content:

low coolant 01 suburban, Low coolant light olds intrigue, how to check radiator fluid level pontiac grand prix, replace low coolent sencor on 1997 chevy lumnia, Low Coolant Sensor Location in olsdmobile silluette, 2002 Chevrolet Impala see a diagram of the a/c controls, 2002 chevy avalanche instrument cluster wiring, p0446 2002 monte carlo, 2002 mercury sable cooling system, evap sensor on 2002 suburban