timing belt alignment for 1993 toyota landcruiser

You search PDF repair manual about timing belt alignment for 1993 toyota landcruiser, if there are search results will appear below. If search results do not exist, please search by others keyword.



  timing belt alignment for 1993 toyota landcruiser Direct Download speed 5432 Kb/s

  timing belt alignment for 1993 toyota landcruiser Full Version speed 8172 Kb/s



Toyota LandCruiser 4.2TD Timing belt replacement intervals

0

Filed Under (Toyota Manuals) by admin on 02-03-2012

download
Timing belt replacement intervals The information relating to timing belt replacement intervals is additional to the main purpose of this CD, but is included to provide guidance to garages and for customer advice. Where possible the recommended intervals have been compiled from vehicle manufacturers’ information. In a few instances no recommendation has been made by the manufacturer and the decision to replace the belt must be made from the evidence of a thorough examination of the condition of the existing belt. Apart from the visible condition of the belt, which is explained fully later in this section, there are several other factors which must be considered when checking a timing belt: Is the belt an original or a replacement. 1. When was the belt last replaced and was it at the correct mileage. 2. Is the service history of the vehicle known. 3. Has the vehicle been operated under arduous conditions which might warrant a shorter replacement interval. 4. Is the general condition of other components in the camshaft drive, such as the tensioner, pulleys, and other ancillary components driven by the timing belt, typically the water pump, sound enough to ensure that the life of the replacement belt will not be affected. 5. If the condition of the existing belt appears good, can you be satisfied that the belt will not fail before the next check or service is due. 6. If the belt does fail, have you considered the consequences. If the engine is an INTERFERENCE type then considerable expensive damage may well be the result. 7. The cost of replacing a belt as part of a routine service could be as little as 5 to 10% of the repair cost following a belt failure. Make sure your customer is aware of the consequences. 8. If in doubt about the condition of the belt – RENEW it. 9. Removal Removal Remove timing belt cover [1]. 1. Turn crankshaft clockwise until timing marks aligned [2]. 2. Ensure timing marks aligned: 1KZ-T/TE: [3]. 3. 4. Remove: Automatic tensioner unit [6]. Tensioner pulley bolt [7]. Tensioner pulley [8]. Timing belt. 5. Installation Installation Check tensioner pulley for smooth operation [8]. Replace if necessary. 1. Remove dust cover. Check tensioner body for leakage or damage [6]. Check pushrod protrusion is 9,0-9,8 mm [9]. 2. Check pushrod does not move when pushed against a firm surface. If pushrod moves: Replace automatic tensioner unit. 3. Slowly compress pushrod into tensioner body until holes aligned. Use press. 4. Retain pushrod with 1,5 mm Allen key through hole in tensioner body [10]. Fit dust cover. 5. Ensure timing marks aligned [2]. 6. Ensure timing marks aligned: 1KZ-T/TE: [3]. 1HD-FT/1HD-FTE: [4]. 7. Fit timing belt in anti-clockwise direction, starting at lower sprocket. Ensure belt is taut between sprockets. 8. Fit tensioner pulley [8]. Tighten bolt to 34 Nm [7]. 9. Push tensioner pulley against belt. Install automatic tensioner unit [6]. Tighten bolts evenly to 13 Nm [5]. 10. Remove Allen key from tensioner body to release pushrod. 11. Turn crankshaft two turns clockwise. Ensure timing marks aligned [2] & [3] or [4]. 12. If not: Repeat installation and tensioning procedures. 13. Install components in reverse order of removal. 14. Reset timing belt replacement warning lamp as follows: 15. -Runner/Landcruiser: Remove grommet in speedometer housing. Depress switch using a thin screwdriver [11]. 16. Colorado: Remove speedometer housing. Remove screw indicated and insert in alternative location [12]. 17. Amazon: Lamp illuminates at 90,000 miles. Return vehicle to dealer.

Related Content:

mazda bt50 timing belt replacement, 4 7L Toyota Timing Belt Replacement, Kia 3 5 Timing Belt Replacement, honda odyssey timing belt replacement mileage, 2004 subaru forester XT timing you tube instalation, Timing Belt Replacement Intervals Pontiac, how often change timing belt 2011 chevy malibu, how to change a timing belt on a 2011 kia soul, how to install varable timing solenoid on gmc envoy xuv 4 2l, how to remove a three bolt crankshaft pulley mazda bt 50

Peugeot 306 Timing belt replacement Removal And Installation Manual

0

Filed Under (Peugeot Manuals) by admin on 23-02-2011

download
Removal Removal Raise and support front of vehicle. 1. Remove: RH front wheel. Engine undershield (if fitted). Lower inner wing panel. Auxiliary drive belt(s). 307: Engine tie-bars. Crankshaft pulley [1] . Timing belt upper cover [2] . Timing belt centre cover [3] . Timing belt lower cover [4] . 2. Turn crankshaft to setting position. Insert timing pins in camshaft sprocket and flywheel [5] & [6] . 3. Slacken tensioner nut to release tension on belt [7] . Lightly tighten nut. 4. Remove timing belt. 5. Installation – -1997 Installation – -1997 Ensure timing pins located correctly [5] & [6] . 1. Fit timing belt in following order: Crankshaft sprocket. Camshaft sprocket. Water pump sprocket. 2. Manufacturer: Peugeot Model: 306 (93-97) 1,4 Engine code: TU3M/Z (KDZ) Output: 55 (75) 5800 Tuned for: R-Cat Year: 1993-97 – Tensioner pulley. NOTE: Ensure belt is taut between sprockets on non-tensioned side. Slacken tensioner nut [7] . Turn tensioner anti-clockwise to tension belt. Temporarily tighten nut. 3. Remove timing pins [5] & [6] . 4. Attach tension gauge to belt at [8] . Tool No.(-).0192/SEEM C.Tronic 105.5. 5. Slacken tensioner nut [7] . 6. Tension belt as follows: 7. Turn tensioner anti-clockwise until tension gauge indicates 45 SEEM units. 8. Tighten tensioner nut to 20 Nm [7] . 9. Remove tension gauge. 10. Turn crankshaft four turns clockwise to setting position. 11. Ensure timing pins can be inserted [5] & [6] . 12. Wait 1 minute to allow belt to settle. 13. Apply firm thumb pressure to belt at . 14. Attach tension gauge to belt at [8] . Tool No.(-).0192/SEEM C.Tronic 105.5. 15. Slacken tensioner nut [7] . 16. Turn tensioner anti-clockwise to tension belt. New belt: 40 SEEM units. Used belt: 36 SEEM units. 17. Tighten tensioner nut to 20 Nm [7] . 18. Remove tension gauge [8] . 19. Turn crankshaft two turns clockwise. 20. Ensure flywheel timing pin can be inserted [6] . NOTE: DO NOT allow crankshaft to turn anti-clockwise. 21. Attach tension gauge to belt at [8] . Tool No.(-).0192/SEEM C.Tronic 105.5. 22. Check tension gauge reading. New belt: 51±3 SEEM units. Used belt: 45±3 SEEM units. 23. Install components in reverse order of removal. 24. Tighten crankshaft pulley bolts to 8 Nm [9] . 25. Installation – 1997- Installation – 1997- Ensure timing pins located correctly [5] & [6] . 1. Fit timing belt in following order: Crankshaft sprocket. Camshaft sprocket. Water pump sprocket. Tensioner pulley. NOTE: Ensure belt is taut between sprockets on non-tensioned side. 2. Slacken tensioner nut [7] . Turn tensioner anti-clockwise to tension belt. Temporarily tighten nut. 3. Remove timing pins [5] & [6] . 4. Attach tension gauge to belt at [8] . Tool No.(-).0192/SEEM C.Tronic 105.5. 5. Slacken tensioner nut [7] . 6. Tension belt as follows: 7. Remove cylinder head cover. 8. Install valve spring compressor. Tool No.0132AE [10] . 9. Turn tensioner anti-clockwise until tension gauge indicates the following: Except 307: 31 SEEM units. 307: 44 SEEM units.

Related Content:

videos on removal of tensioner pulley on 2005 dodge neon, MERITOR HUB A433T4232, volvo penta 5 belt tighten, remove right timing belt cover 2004 axiom, HUB A433T4232, peugeot 307 camshaft repair, what tool to release tension from automatic tensioner 2007 impala, picture belt assembly on 98 4 3 volvo penta, peugeot pdf belt, how to get the serpentine belt on a volvo penta 4 3 gxi

2001 Daewoo Leganza SE TIMING BELT REMOVAL And INSTALLATION Manual

0

Filed Under (Daewoo Manuals) by admin on 13-05-2011

download
TIMING BELT Removal 1. Disconnect negative battery cable. Disconnect intake air temperature sensor connector from intake air duct. Disconnect the air intake tube from the throttle body. Disconnect the breather tube from the valve cover. Remove resonator from throttle body. Remove air filter housing. 2. Raise and support the vehicle. Remove right front wheel. Remove right front splash shield from wheelwell. Remove serpentine accessory drive belt. 3. Remove crankshaft pulley bolts. It is NOT necessary to remove crankshaft sprocket center bolt. Remove crankshaft pulley. Lower vehicle. 4. Support engine assembly from above with Support Fixture (J-28467-B). See Fig. 1 . Remove engine mount bracket from timing belt end of engine. See Fig. 2 . 5. Remove power steering hose clamp bolt, and position hose away from timing belt cover. Remove front timing belt cover. See Fig. 3 . Using crankshaft center bolt, rotate crankshaft one full turn clockwise (as viewed from timing belt end of engine). 6. Align mark on crankshaft sprocket with notch at bottom of rear timing belt cover. See Fig. 4 . Align camshaft sprocket timing marks with notches on valve cover. See Fig. 5 . 7. Loosen the automatic tensioner bolt. Use an Allen wrench to rotate tensioner and relieve tension on timing belt. See Fig. 6 . Remove timing belt Fig. 6: Identifying Timing Belt Tensioner Courtesy of DAEWOO MOTOR AMERICA, INC. Installation 1. Ensure crankshaft and camshaft timing marks are still aligned. Install the timing belt. See Fig. 7 . Turn the timing belt tensioner counterclockwise to tension the timing belt. Turn tensioner until the pointer aligns with the notch on the rear timing belt cover. Tighten automatic tensioner bolt to specification. See TORQUE SPECIFICATIONS . 2. Using crankshaft center bolt, turn crankshaft clockwise (as viewed from timing belt end of engine) 2 full revolutions. Ensure timing belt tensioner pointer is still aligned with notch. 3. If timing belt tensioner is correctly aligned, install timing belt cover. See Fig. 3 . Install the engine mount bracket on the timing belt end of engine. Position power steering hose in place, and install clamp bolt. Install crankshaft pulley. Install serpentine accessory drive belt. 4. Install right front splash shield. Install right front wheel. Install air filter housing and resonator.

Related Content:

2006 kia sedona 3 8 engine timing mark, 02 is 300 lexus tsib vvt-i pulley installation, timing mark on hino, 98 eclipse rs service manual, 91 honda accord timing belt marks diagram, 2002 diamante timing belt, 2002 jetta crank mark, 2003 eclipsed2 4 litre cranckshaft position sensor location, changing timing belt 2004 kia optima EX 2 7 6 cylinder ?, should the timing arrow on a zx2 move when belt is pressed

1996 Mitsubishi Eclipse GS-T TIMING BELT And BALANCE SHAFT BELT REMOVAL AND INSTALLATION MANUAL

0

Filed Under (Mitsubishi Manuals) by admin on 29-04-2012

download
Removal 1. Disconnect negative battery cable. Remove engine undercover. Place wooden block between jack and oil pan, and raise engine slightly. Remove engine mount assembly near timing belt cover. 2. Remove clamp for power steering return hose near timing belt cover. Remove all drive belts and tensioner pulley bracket. See Fig. 1 . Remove power steering and water pump pulleys. Rotate crankshaft clockwise so that No. 1 cylinder is at TDC of compression stroke. Remove crankshaft pulley. 3. Remove upper timing belt cover and gasket. Remove stub bolt of engine support bracket, and remove center timing belt cover. Remove lower timing belt cover. 4. Ensure camshaft, crankshaft and oil pump sprocket timing marks are aligned. See Fig. 2 or Fig. 3 . Loosen tensioner pulley center bolt. Move tensioner to relieve timing belt tension. Remove timing belt. Remove timing belt auto tensioner. See Fig. 1 . 5. Remove plug from left side of cylinder block. Install a .31″ (8.0 mm) diameter Phillips screwdriver into the hole against balance shaft. See Fig. 4 . Screwdriver must go in at least 2.36″ (60 mm) or more. If screwdriver will only go in about .79-.98″ (20-25 mm) before striking balance shaft, turn sprocket one revolution and align timing mark. Keep screwdriver in place until timing belt is installed. This ensures balance shaft driven by oil pump sprocket remains in correct position. 6. To remove timing belt “B” (balance shaft belt), hold crankshaft sprocket stationary with a spanner wrench. Remove crankshaft sprocket bolt. Using gear puller, remove outer crankshaft sprocket. 7. Remove crankshaft sensing blade (if equipped). See Fig. 5 . Loosen timing belt “B” tensioner bolt. If reusing timing belt “B”, mark direction of belt rotation for reassembly reference. Remove timing belt “B Inspection 1. Inspect timing belts for damaged teeth and cracking. Ensure belts are not contaminated with oil. Check tensioners for free rotation and grease leakage. Replace components if damaged or if grease leakage exists. 2. Check timing belt auto tensioner for leaks. Hold timing belt auto tensioner upright. Measure rod protrusion above edge of housing. See Fig. 6 . Length should be .47″ (12 mm). Apply 22-44 lbs. (10-20 kg) of force to end of rod. If auto tensioner rod moves more than 0.39″ (1 mm), replace the auto tensioner.

Related Content:

1996 nissan pathfinder timing set-up, 1996 toyota rav 4 timing belt replacement, belt diagram for 1996 toyota corola, check timing eclipse gst, timing spec diagram 1996 mitsubishi montero

2002 Toyota Truck Tundra Access Cab SR5 2WD Timing Belt Service and Repair Manual

0

Filed Under (Toyota Manuals) by admin on 09-06-2012

download
2002 Toyota Truck Tundra Access Cab SR5 2WD V6-3.4L (5VZ-FE) Copyright © 2008, ALLDATA 9.50 Page 2 REMOVAL 1. REMOVE ENGINE UNDER COVER 2. DRAIN ENGINE COOLANT 3. DISCONNECT UPPER RADIATOR HOSE 4. DISCONNECT PS PUMP FROM ENGINE a. Disconnect the 2 PS air hoses from the air intake chamber and resonator. b. Remove the bolt holding the PS pressure tube clamp to the frame. c. Remove the drive belt. d. Remove the bolt and nut, and disconnect the PS pump from the engine. 5. w/ A/C: DISCONNECT A/C COMPRESSOR FROM ENGINE a. Disconnect the A/C compressor connector. b. Remove the drive belt. c. Remove the 4 bolts, and disconnect the A/C compressor from the engine. 6. LOOSEN FAN WITH FLUID COUPLING AND FAN PULLEYS 7. REMOVE DRIVE BELT FOR GENERATOR 8. REMOVE NO.2 FAN SHROUD 9. REMOVE FAN WITH FLUID COUPLING AND FAN PULLEYS 10. w/ A/C: REMOVE A/C COMPRESSOR BRACKET Remove the 5 bolts and A/C compressor bracket. 11. DISCONNECT UPPER RADIATOR HOSE 12. REMOVE NO.2 TIMING BELT COVER a. Disconnect the camshaft position sensor connector from the No. 2 timing belt cover. b. Disconnect the 4 high-tension cord clamps from the No. 2 timing belt cover. c. Remove the 6 bolts and timing belt cover. 13. REMOVE FAN BRACKET a. Remove the nut and PS pump adjusting strut. b. Remove the bolt, nut and fan bracket. 14. SET NO. 1 CYLINDER AT TDC/COMPRESSION a. Turn the crankshaft pulley and align its groove with timing mark “0″ of the No. 1 timing belt cover. b. Check that the timing marks of the camshaft timing pulleys and No. 3 timing belt cover are aligned. If not, turn the crankshaft pulley 1 revolution (360°) . HINT: When re-using timing belt: Place the matchmarks on the timing belt and camshaft timing pulleys, and place matchmark on timing belt to match the end of the No. 1 timing belt cover. 15. REMOVE TIMING BELT TENSIONER Alternately loosen the 2 bolts, and remove them, the belt tensioner and dust boot. 16. REMOVE TIMING BELT

Related Content:

toyota tacoma 2000 REMOVE COMPRESSOR DRIVE BELT, 2002 ford ranger 2 3L timing tool, 2002 nissan altima changing camshafts, 2002 toyota tundra manual, Centurial Timing Module

2000 Cadillac Catera Timing Belt Service and Repair Manual

0

Filed Under (Cadillac Manuals) by admin on 20-01-2012

download
Timing Belt Replacement TIMING BELT REPLACEMENT Removal Procedure ^ Tools Required -J 42069 Timing Belt Alignment Kit -J 42098 Crank Hub Torx Socket Notice: Failure to follow the described timing belt inspection and maintenance may result in a broken timing belt and cause severe engine damage. 1.Inspect the cold start counter (also called a heavy duty register) with a scan tool. If there are any cold starts (below -28° C or -20° F) visually inspect the timing belt for cracks. It cracks are noted, do not reuse the belt. Replace the belt and clear the cold start counter. If the belt is okay, and is reused, do not clear the cold start counter. 2.Remove the intake air resonator. Refer to Intake Air Resonator Replacement in Powertrain Management. 3.Remove the intake plenum. Refer to Intake Plenum Replacement. 4.Remove the timing belt cover. Refer to Timing Belt Cover Replacement. 5.Remove the crankshaft balancer bolts. 6.Remove the crankshaft balancer from the crankshaft sprocket. 7.Rotate the crankshaft clockwise to 60 degrees Before Top Dead Center (BTDC) 8.Install the J 42069-10 to the crankshaft sprocket with the knurled bolt. 9.Use the J 42098 to carefully turn the crankshaft in the engine rotational direction (clockwise) until the lever of the J 42069-10 firmly contacts the water pump pulley flange. 10.Secure the moveable lever of the tool to the water pump pulley flange. Important: Ensure that the crankshaft is not 180 degrees off TDC. The reference marks on the camshaft gears should be aligned with the corresponding notches on the rear timing belt cover at this point. If they are not aligned, the engine is 180 degrees off. 11.Install the J 42069-1 and the J 42069-2 to the camshaft gears. If the J 42069-1 or the J 42069-2 do not fit into the teeth of the camshaft gears, it may be necessary to loosen the relevant timing belt idler pulley and turn the cam until the J 42069-1 or the J 42069-2 can be inserted. Notice: After timing belt is removed, never turn camshaft and crankshaft independently. If turned, interference may occur among pistons and valves, and parts related to pistons and valves may be damaged. 12.Loosen the timing belt tensioner and idler pulleys. Important: Do not remove J 42069-1 and the J 42069-2 while the belt is removed. 13.Remove the timing belt. Installation and Initial Adjustment Procedure ^ Tools Required -J 42069 Timing Belt Alignment Kit -J 42098 Crank Hub Torx Socket

Related Content:

2000 catera timing belt replacement cost, lincoln 3 9 timing tools

TIMING BELT COMPONENTS FOR REMOVAL AND INSTALLATION MANUAL

0

Filed Under (More Manuals) by admin on 13-07-2012

download
TIMING BELT REMOVAL 1. DRAIN ENGINE COOLANT 2. REMOVE ENGINE UNDER COVER 3. REMOVE AIR CLEANER DUCT 4. REMOVE DRIVE BELT, FAN WITH FLUID COUPLING AND WATER PUMP PULLEY (See step 5 in water pump removal in Cooling System) 5. REMOVE RADIATOR ASSEMBLY (See steps 5 and 6 in radiator removal in Cooling System) 6. REMOVE NO.3 TIMING BELT COVER (a) Remove the oil filler cap. (b) Using a 5 mm hexagon wrench, remove the 6 bolts and belt cover. 7. REMOVE NO.2 TIMING BELT COVER Using a 5 mm hexagon wrench, remove the 3 bolts, belt cover and gasket. If you are unable to loosen the bolt on the right because the PS pump pulley interferes with the hexagon wrench, first remove the pulley as follows. (a) Using SST to hold the pulley, remove the nut. SST 09960-10010 (b) Remove the pulley. 8. REMOVE DRIVE BELT TENSIONER Remove the 3 bolts and tensioner. – ENGINE ENGINE MECHANICAL EG-19 9. SET NO.1 CYLINDER TO TDC/COMPRESSION (a) Turn the crankshaft pulley, and align its groove with timing mark “0″ of the No.1 timing belt cover. NOTICE: Always turn the crankshaft clockwise. (b) Check that the timing marks of the camshaft timing pulleys are aligned with the timing marks of the No.4 timing belt cover. If not, turn the crankshaft 1 revolution (360?). 10. REMOVE TIMING BELT FROM CAMSHAFT TIMING PULLEYS HINT (Re-using timing belt): Place matchmarks on the timing belt and camshaft timing pulleys as shown in the illustration. (a) Alternately loosen the 2 bolts, and remove them, the tensioner and dust boot. (b) Disconnect the timing belt from the camshaft timing pulleys. 11. REMOVE CAMSHAFT TIMING PULLEYS Using SST, remove the bolt for the timing pulley. Remove both timing pulleys. SST 09960-10010 (09962-01000, 09963-01000) 12. REMOVE CRANKSHAFT PULLEY (a) Using SST, loosen the pulley bolt. SST 09213-70010, 09330-00021 (b) Remove the SST and pulley bolt

Related Content:

ford E250 rear vaporline to carben canester diagram, 2008 mazda 2 3 timing procedure, 1999 honda odyssey repair manual pdf, NTC350 drive gear remova, remove head timing cover on a 96 altima, remove timing cover 2005 Nissan Altima 2 5 L, removing pulleys timing belt cover 3000 gt, set timing on 2005 aveo, timing marks for 2005 nissan altima 2 5, Variable Camshaft Timing Solenoid Picture

2004 Kia Sorento EX TIMING BELT REMOVAL AND INSTALLATION MANUAL

0

Filed Under (Kia Motors Manuals) by admin on 03-06-2012

download
REMOVAL & INSTALLATION TIMING BELT Removal 1. Disconnect negative battery cable. Remove engine cover. Using 16-mm spanner wrench, rotate serpentine belt tension arm clockwise about 14 degrees to relieve belt tension. Remove serpentine drive belt. Remove power steering pump pulley, idler pulley, tensioner pulley and crankshaft pulley. Remove upper and lower timing belt covers. See Fig. 1 or Fig. 2 . 2. Ensure timing marks of camshaft sprocket and cylinder head cover are matching. See Fig. 5 . On Sedona, support engine with jack and remove engine mounting insulator. On all models, remove auto tensioner. See Fig. 3 . 3. Unbolt timing belt tensioner pulley, and remove timing belt. CAUTION: This application is an interference engine. Do not rotate camshaft or crankshaft when timing belt is removed, or engine damage may occur. NOTE: Rotate crankshaft clockwise and align timing mark to set No. 1 cylinder to TDC on compression stroke. NOTE: If timing belt is to be reused, mark rotational direction on belt for reinstallation reference. CAUTION: If either camshaft is set at TDC for cylinder No. 1 at the compression stroke and the corresponding camshaft on the same cylinder head is rotated 180 degrees while the timing belt is removed, intake and exhaust valves may contact each other Inspection Inspect timing belt for wear on edges of drive teeth. Inspect the belt for signs of oil contamination, cracks, separation, worn or missing teeth, or hardened Black surface. Replace belt if worn, damaged or contaminated. Inspect belt tensioner pulley for smooth rotation. Replace if defective. Check timing belt auto tensioner for leaks. Replace if necessary. Installation 1. Install timing belt idler pulley to engine support lower bracket. Install tensioner arm, shaft and washer to cylinder block. Tighten tensioner arm bolt to specification. See TORQUE SPECIFICATIONS . 2. Install crankshaft sprocket and align timing mark. See Fig. 4 . Install camshaft sprocket and adjust installation positions as shown. See Fig. 5 and Fig. 6 . Install auto tensioner to oil pump case. Ensure that

Related Content:

change timing belt 2004 kia sorento, 2003 kia sorento power steering pump replacement, 2004 sorento replace drive belts, how to install a motor mount on a kia sedona, how to replace the camshaft pulley bolt on a 2004 Kia Sorento here at home?, how to take a intake manifold off of a 2003 kia sorento, how to time a 2004 kia sorento, kia sedona steering pump rebuilt, kia sorento drive shaft repair

1994 Mitsubishi Expo LRV TIMING BELT REMOVAL AND INSTALLATION MANUAL

0

Filed Under (Mitsubishi Manuals) by admin on 30-04-2012

download
Removal 1. Remove radiator shroud, cooling fan and pulley. Remove all drive belts and crankshaft pulleys. Remove upper timing belt covers and gaskets. Note bolt length and location. 2. Remove crankshaft sprocket bolt and washer. Rotate crankshaft clockwise (as viewed from timing belt end of engine) until cylinder No. 1 is at TDC of compression stroke. Align timing mark on camshaft sprocket with mark on cylinder head. See Fig. 5 . 3. Loosen timing belt tensioner adjustment bolt, and move tensioner toward water pump. Tighten bolt to secure tensioner. Remove front timing belt and tensioner. DO NOT rotate crankshaft after timing belt has been removed. 4. Remove camshaft sprocket (if necessary). Remove oil pump sprocket access plug from cylinder block. See Fig. 4 . Insert a .31″ (8.0 mm) diameter Phillips screwdriver to block left silent shaft. 5. Remove oil pump sprocket nut, and remove sprocket. Remove front crankshaft sprocket and flange. Note direction and order of installation for reassembly reference. 6. Remove rear timing belt tensioner assembly. Remove rear timing belt. Remove right silent shaft sprocket with spacer (if necessary). Remove rear crankshaft sprocket with key Installation 1. Install rear crankshaft sprocket and flange. Install right silent shaft sprocket and spacer. Spacer should be installed with chamfered end into oil seal. Align timing marks. See Fig. 5 . 2. Install rear tensioner. Hold tensioner tightly against belt while tightening bolts. Ensure deflection is .20- .28″ (5.0-7.1 mm). See Fig. 6 . Install camshaft sprocket. Tighten camshaft sprocket bolt to specification. See TORQUE SPECIFICATIONS . 3. Install front timing belt tensioner, tension spring and spacer. Ensure spring is properly engaged against water pump case. Rotate tensioner toward water pump, and temporarily tighten bolts. Ensure timing marks are aligned. See Fig. 5 . Install timing belt on crankshaft. 4. Apply pressure on tension side of timing belt while installing belt (in order) on crankshaft, oil pump and camshaft sprockets. Loosen tensioner to apply spring pressure to timing belt. 5. To apply tension to belt, rotate crankshaft clockwise until camshaft sprocket timing mark is offset by 2 teeth. Tighten tensioner bolt. Tighten tensioner spacer nut

Related Content:

04 volvo s60 2 5t how to align cam shafts to cam sprockets, adjusting cam sprockets, chrysler sprocket removal tool, ej25d enigine TORQUE, what are torque values for 2 2ecotec cam sprokets

1994 Toyota Camry DX TIMING BELT REMOVAL AND INSTALLATION MANUAL

0

Filed Under (Toyota Manuals) by admin on 22-01-2012

download
Removal 1. Disconnect negative battery cable. Raise and support vehicle. Remove lower engine cover. On Celica and Camry, remove right front wheel. On all models, lower vehicle. 2. On MR2, remove right hood side panel and cruise control actuator. Remove right rear wheel. On Celica and Camry, remove alternator from engine and secure out of way. On Camry, remove coolant reservoir tank if it interferes with timing belt removal. Remove engine control (torque) rod from front of engine. 3. On all models, remove accessory drive belts. Using floor jack, slightly raise engine to remove weight from right (timing belt side) engine mount at timing belt cover. 4. Remove right (timing belt side) engine mount and bracket from front of engine. Remove spark plugs. Remove No. 2 timing belt cover and gaskets. See Fig. 1 . 5. Rotate crankshaft clockwise so cylinder No. 1 is at TDC on compression stroke. Cylinder No. 1 is front cylinder at timing belt end of engine. 6. Ensure timing mark on crankshaft pulley aligns with “0″ mark on No. 1 timing belt cover. Ensure hole in camshaft sprocket aligns with alignment mark on camshaft bearing cap. See Fig. 2 . If hole in camshaft sprocket is not aligned with alignment mark, rotate crankshaft clockwise one full revolution. 7. Loosen No. 1 idler pulley bolt. See Fig. 1 . Move No. 1 idler pulley outward, away from timing belt as far as possible. Temporarily retighten No. 1 idler pulley bolt. Remove timing belt from camshaft sprocket. 8. Using Pulley Holder (SST 09213-54015) or equivalent, hold crankshaft pulley. Remove crankshaft pulley bolt. 9. Using gear puller, remove crankshaft pulley. Remove No. 1 timing belt cover and gasket. Note direction of timing belt guide installation. See Fig. 1 . Remove timing belt guide. 10. Loosen No. 1 idler pulley bolt. See Fig. 1 . Remove timing belt from crankshaft sprocket. Remove idler pulleys (if necessary).

Related Content:

96 Toyota Camry 3 0 Timing Marks, TOYOTA 4Y TIMING MARKS, toyota 7A-FE timing belt alignment marks, Toyota Camry Crankshaft Pulley Removal

Related Content:

mazda bt50 timing belt replacement, 4 7L Toyota Timing Belt Replacement, Kia 3 5 Timing Belt Replacement, honda odyssey timing belt replacement mileage, 2004 subaru forester XT timing you tube instalation, Timing Belt Replacement Intervals Pontiac, how often change timing belt 2011 chevy malibu, how to change a timing belt on a 2011 kia soul, how to install varable timing solenoid on gmc envoy xuv 4 2l, how to remove a three bolt crankshaft pulley mazda bt 50