timing chain lincoln engine fix video

You search PDF repair manual about timing chain lincoln engine fix video, if there are search results will appear below. If search results do not exist, please search by others keyword.



  timing chain lincoln engine fix video Direct Download speed 5432 Kb/s

  timing chain lincoln engine fix video Full Version speed 8172 Kb/s



2001 Ford Taurus/ Sable Cooling System Draining Filling and Bleeding Workshop Manual

0

Filed Under (Ford Manuals) by admin on 19-02-2011

download
CAUTION: Vehicle cooling systems are filled with Motorcraft Premium Engine Coolant VC-4-A (in Oregon VC-5, in Canada CXC-10) or an equivalent meeting Ford specification ESE-M97B44-A. NOTE: Less than 80% of the coolant capacity can be recovered with the engine in the vehicle. Dirty, rusty or contaminated coolant requires replacement. 1. Release the pressure in the cooling system by slowly turning the pressure relief cap one half to one turn counterclockwise to the first stop on the filler neck. When the pressure has been released, remove the pressure relief cap. 2. Raise and support the vehicle. For additional information, refer to Section 100-02 . 3. Remove the front splash shield. 4. Place a suitable container below the radiator draincock. Drain the coolant. 5. Close the radiator draincock when finished. Filling and Bleeding With RADKITPLUS 1. Using the special tool, install the RADKITPLUS and follow the RADKITPLUS manufacturer’s instructions to fill and bleed the cooling system. Filling Without RADKITPLUS CAUTION: Engine coolant provides freeze protection, boil protection, cooling efficiency and corrosion protection to the engine and cooling components. In order to obtain these protections, the engine coolant must be maintained at the correct concentration and fluid level. When adding engine coolant, use a 50/50 mixture of engine coolant and clean, drinkable water. To maintain the integrity of the coolant and the cooling system: * Add Motorcraft Premium Engine Coolant VC-4-A (in Oregon VC-5, in Canada CXC-10) or equivalent meeting Ford specification ESE-M97B44-A. * Do not add Motorcraft Specialty Engine Coolant VC-2 or an equivalent meeting Ford specification WSS-M97B44-D. Mixing coolants may degrade the coolant’s corrosion protection. * Do not add alcohol, methanol, brine or any engine coolants mixed with alcohol or methanol antifreeze. These can cause engine damage from overheating or freezing. * Do not mix with recycled coolant unless it meets the requirement of specification ESE-M97B44-A. Not all coolant recycling processes meet this specification. Use of such a coolant may harm the engine and cooling system components. 1. Install the front splash shield. 2. Lower the vehicle. 3. Fill the degas bottle with the correct engine coolant mixture. 4. Install the pressure relief cap. 5. Move the temperature blend selector to the full warm position. 6. WARNING: Do not stand in line with or near the engine cooling fan blade when revving the engine. Run the engine until it reaches operating temperature. 7. Add the correct coolant mixture to the degas bottle until the coolant level is between the COOLANT FILL LEVEL marks. 8. Turn off the engine and allow the cooling system to cool. Recheck the coolant level and fill the cooling system to the FULL mark on the degas bottle. 9. WARNING: Do not stand in line with or near the engine cooling fan blade when revving the engine. Repeat Steps 3 through 8 until the reservoir level is OK. Bleeding Without RADKITPLUS 1. Bleed the cooling system as follows: * Select the maximum heater temperature and blower motor speed settings. Position the control to discharge air from the A/C vents in the instrument panel. * WARNING: Do not stand in line with or near the engine cooling fan blade when revving the engine. Start the engine and allow it to idle. While the engine is idling, feel for hot air from the A/C vents. * CAUTION: If the air discharge remains cool and the engine coolant temperature gauge does not move, the engine coolant level is low in the engine and must be filled. Stop the engine, allow it to cool and fill the cooling system. Start the engine and allow it to idle until the normal operating temperature is reached. Hot air should discharge from the A/C vents. The engine coolant temperature gauge should maintain a stabilized reading in the middle of the NORMAL range and the upper radiator hose should feel hot to the touch. * Shut the engine off and allow it to cool. * Check the engine for coolant leaks. * Check the engine coolant level in the degas bottle and fill it as necessary.

Related Content:

4D35 engine repair manual, 6m70 wiring diagram, 2000 Nissan sentra 1 8 engine bolt torque diagram, so5d engine repair manual, so5d engine, TOYOTA SO5D SERVICE MUNAL, what causes damage to a flywheel on a 2004 yukon, SO5D OBD ll Code, 2005 chevy impala motor diagram, Position of sensors in mitsubishi 4m 51 engine

1997 Saturn SL2 FRONT COVER And TIMING CHAIN REMOVAL AND INSTALLATION MANUAL

0

Filed Under (Saturn Manuals) by admin on 10-05-2012

download
Removal 1. Disconnect negative battery cable. Raise and support vehicle. Drain engine oil. Remove right front wheel and splash shield. Put a block of wood between cradle and engine torque strut at bottom front end of engine. See Fig. 2 . 2. Remove mount from upper front end of engine, allowing engine to rest on wood block. Remove accessory drive belt and tensioner. Remove accessory belt idler. Remove cylinder head cover. 3. Replace silicone isolators on cylinder head cover screws if deteriorated. Remove power steering pump (leave hoses attached). Remove A/C compressor (leave hoses attached). Raise and support vehicle. Drain engine oil. Remove right front wheel and splash shield. 4. Remove support bracket between intake manifold and engine block. Remove front balancer/pulley using a 3-jaw puller. Disconnect exhaust pipe from exhaust manifold. Install Crankshaft Gear Retainer (SA9104E) onto end of crankshaft, with flat side toward crankshaft gear (sprocket). Crankshaft gear retainer holds crankshaft gear in place during removal of front cover. 5. Remove 4 bolts from front end of oil pan. Using RTV Cutter (SA9123E), cut RTV sealant between oil pan and front cover. Spray penetrating oil onto front cover dowel pins. Remove front cover bolts (one bolt is located above accessory drive belt pulley). Pry front cover from engine block. 6. To prevent pistons from hitting valves, turn crankshaft 90 degrees clockwise as viewed from front of engine until timing mark and keyway are aligned with split line of main bearing cap. Remove timing chain tensioner, guides and chain. While using a 7/8″ (21 mm) wrench to keep camshaft(s) from turning, remove camshaft sprocket bolt(s). Remove camshaft sprocket(s). Installation 1. To prevent pistons from hitting valves, ensure timing mark and keyway on crankshaft are aligned with split line of main bearing cap. Install camshaft sprocket(s) with the letters FRT (front) facing away from cylinder head. Use a 7/8″ (21 mm) wrench to keep camshaft(s) from turning. 2. Install and tighten camshaft sprocket bolt(s) to specification. Rotate camshaft(s) until a 3/16″ (4.8 mm) drill bit can be inserted through timing pin hole(s) and into cylinder head. See Fig. 5 or Fig. 6 . 3. Rotate crankshaft counterclockwise as viewed from front of engine until timing marks at crankshaft sprocket are aligned. Install timing chain, aligning Silver-plated chain links with timing mark(s) on camshaft sprocket(s) and bottom tooth (or teeth) of crankshaft sprocket. See Fig. 5 or Fig. 6 . 4. Install fixed chain guide. Slack part of chain should be on tensioner side of cylinder block. Chain should be tight against fixed chain guide. Install pivoting chain guide. Retract tensioner plunger, and pin ratchet

Related Content:

1997 saturn manifold repair, 2000 lexus es 300 gear sprocket, 2007 SATURN RELAY 3 9 V6 TIMING CHAIN/ MAGNETIC SPROCKET

1999 Saturn SL1 L4-1.9L SOHC VIN 8 Engine – Driveability Concerns/ Cooling System DTC’s Set

0

Filed Under (Saturn Manuals) by admin on 19-05-2012

download
1. Disconnect engine coolant temperature sensor electrical connector and inspect sensor and connector terminals for corrosion and/or evidence of engine coolant. ^If terminals are corroded or if there is evidence of engine coolant proceed to step 4. ^If terminals are not corroded and there is no evidence of engine coolant, reconnect the electrical connector and continue to next step. 2. Perform one or both of the following checks to determine whether the engine coolant temperature sensor is providing the correct temperature indication. If engine coolant temperature sensor reading does not pass either of the above tests, continue with next step. ^If engine is at ambient temperature (vehicle has been sitting overnight or not started for several hours), use a Scan tool to compare the inlet air temperature ( IAT ) to the engine coolant temperature ( ECT ). These two readings should be within 2°C (4°F) of each other. ^If engine is at operating temperature, install a thermometer in the coolant recovery reservoir. With the engine running and A/C off, use a Scan tool to compare the engine coolant temperature sensor reading to the thermometer reading. These two readings should be within 8°C (15°F) of each other If engine coolant temperature sensor reading passes both of the tests above, refer to appropriate symptom diagnostic chart in the Engine/Emissions Controls Section of applicable Engine Service Manual. 3. Turn ignition off. 4Remove coolant surge tank cap. 5. Drain at least 1.9 L (2 Qt.) of engine coolant from the cooling system by opening radiator drain valve or removing engine drain plug. Collect engine coolant in a container. 6. Disconnect engine coolant temperature sensor electrical connector. 7. Remove engine coolant temperature sensor from cylinder head. 8. Obtain replacement engine coolant temperature sensor (P/N 21025106). 9. Use appropriate tap to clean sensor mounting hole of any thread sealant residue. 10. Install engine coolant temperature sensor in cylinder head. Torque: Engine Coolant Temperature Sensor: 8 Nm (71 in-lbs) 11. Inspect harness connector terminals for corrosion and/or evidence of engine coolant. If harness connector terminals are corroded or there is evidence of engine coolant, the harness connector must be replaced with new connector (P/N 12117087-includes: connector, terminals, wires, and splice sleeves). 12. Connect engine coolant temperature sensor connector. 13. Transfer engine coolant drained in step 5 into coolant surge tank. If necessary fill coolant surge tank to the FULL COLD range with 50/50 solution of correct type of antifreeze and clean water. 14. Start engine and check for leaks. 15. Run engine until upper radiator hose is hot, then add additional coolant if needed to bring the level to the FULL COLD level (1991-early 1997) or within the Min./Max. cold range (late l997-2001). 16. Install coolant surge tank cap.

Related Content:

yhs-sgm_fb, wiring diagram for 2005 kia sedona engine cooling fan temperature sensor, bye pass c15 timming sensor, replacing s radiator 2001 silhouette oldsmobile, crank sensor location on 6 7 power stroke, 2001 oldsmobile intrique coolant system diagram, location of air temp sensor on 2001 toyota celica, 2001 mitsubishi montero limited head gasket repair procedure pdf download, how to drain radiator on 2007 ford fusion 2 3 L, hino j500 pump timing marks

2001 Daewoo Leganza SE TIMING BELT REMOVAL And INSTALLATION Manual

0

Filed Under (Daewoo Manuals) by admin on 13-05-2011

download
TIMING BELT Removal 1. Disconnect negative battery cable. Disconnect intake air temperature sensor connector from intake air duct. Disconnect the air intake tube from the throttle body. Disconnect the breather tube from the valve cover. Remove resonator from throttle body. Remove air filter housing. 2. Raise and support the vehicle. Remove right front wheel. Remove right front splash shield from wheelwell. Remove serpentine accessory drive belt. 3. Remove crankshaft pulley bolts. It is NOT necessary to remove crankshaft sprocket center bolt. Remove crankshaft pulley. Lower vehicle. 4. Support engine assembly from above with Support Fixture (J-28467-B). See Fig. 1 . Remove engine mount bracket from timing belt end of engine. See Fig. 2 . 5. Remove power steering hose clamp bolt, and position hose away from timing belt cover. Remove front timing belt cover. See Fig. 3 . Using crankshaft center bolt, rotate crankshaft one full turn clockwise (as viewed from timing belt end of engine). 6. Align mark on crankshaft sprocket with notch at bottom of rear timing belt cover. See Fig. 4 . Align camshaft sprocket timing marks with notches on valve cover. See Fig. 5 . 7. Loosen the automatic tensioner bolt. Use an Allen wrench to rotate tensioner and relieve tension on timing belt. See Fig. 6 . Remove timing belt Fig. 6: Identifying Timing Belt Tensioner Courtesy of DAEWOO MOTOR AMERICA, INC. Installation 1. Ensure crankshaft and camshaft timing marks are still aligned. Install the timing belt. See Fig. 7 . Turn the timing belt tensioner counterclockwise to tension the timing belt. Turn tensioner until the pointer aligns with the notch on the rear timing belt cover. Tighten automatic tensioner bolt to specification. See TORQUE SPECIFICATIONS . 2. Using crankshaft center bolt, turn crankshaft clockwise (as viewed from timing belt end of engine) 2 full revolutions. Ensure timing belt tensioner pointer is still aligned with notch. 3. If timing belt tensioner is correctly aligned, install timing belt cover. See Fig. 3 . Install the engine mount bracket on the timing belt end of engine. Position power steering hose in place, and install clamp bolt. Install crankshaft pulley. Install serpentine accessory drive belt. 4. Install right front splash shield. Install right front wheel. Install air filter housing and resonator.

Related Content:

2006 kia sedona 3 8 engine timing mark, 02 is 300 lexus tsib vvt-i pulley installation, 2002 jetta crank mark, 2003 eclipsed2 4 litre cranckshaft position sensor location, 3126 timing pin hole, 91 honda accord timing belt marks diagram, 98 eclipse rs service manual, changing timing belt 2004 kia optima EX 2 7 6 cylinder ?, how to adjust belt on 2001 kia optima, kia rio 5 2007 timming belt

1995 Nissan-Datsun 200SX Timing Chain/ Front Cover Revised Procedure

0

Filed Under (Nissan Manuals) by admin on 27-01-2012

download
Removal 1. Set # 1 piston at TDC on its compression stroke. 2. Remove the spark plug wires. 3. Remove the rocker cover (see Figure 1). 4. Remove the coolant reservoir tank with bracket and reposition it for clearance. 5. Support the engine with a suitable jack. 6. Remove cylinder head front mounting bracket. 7. Remove engine front mounting, then the engine front mounting bracket. 8. Remove cylinder head front cover 9. Remove the upper chain tensioner (see Figure 2). 10. Wipe off the links of the upper timing chain next to the timing marks on the sprockets. Put paint marks on the timing chain, matching them with the timing marks on the cam sprockets and idler sprocket (see Figure 3) 11. Remove the four (4) front cover to cylinder head bolts. 12. Remove side and lower engine compartment splash covers. 13. Remove the accessory drive belts. 14. Remove the crankshaft pulley. 15. Drain coolant by removing the cylinder block drain plug and opening the radiator drain cock (Refer to MA section of the Service Manual). 16. Drain engine oil. 17. Remove intake manifold support of engine front side. 18. Remove power steering pump, pump bracket and tension rod. Position pump aside for clearance. 19. Remove the thermostat housing (See Figure 4) 20. Remove the lower chain tensioner (see Figure 5). 21. Remove the front exhaust tube. Refer to the “FE” section (Exhaust System) of the Service Manual. 22. Remove the front and rear engine gussets (if equipped) on either side of the oil pan. NOTE: On A/T models, remove the rear plate cover. 23. Remove the oil pan (see Figure 6). a. Insert the Tool between the cylinder block and oil pan. CAUTION: Be careful not to damage the aluminum mating face. Do not insert a screwdriver, or the oil pan flange will become damaged. b. Slide the Tool by tapping it on the side of the Tool with a hammer. 24. Remove the A/C compressor and position it aside for clearance. 25. Remove the A/C and alternator bracket with the alternator. 26. Remove the oil pump drive spacer. CAUTION: Be careful not to scratch the drive spacer when removing it. 27. Remove the front cover bolts and front cover. CAUTION: One bolt is located on the water pump (see Figure 7). *1: Located on engine front mounting bracket. *2: Located on the water pump. *3: Located on the power steering oil pump adjusting bar. CAUTION: Be careful not to tear or damage the cylinder head gasket. 28. Remove the cylinder block to front cover alignment dowels. CAUTION: Do not hit the dowels or the cylinder block will crack. 29. Wipe off the links of the lower timing chain next to the timing marks on the sprockets. Put paint marks on the timing chain, matching them with the timing marks on the idler sprocket and crankshaft sprocket (see Figure 8). Installation 1. Install the crankshaft sprocket, making sure the mating marks face the front of the engine. 2. Install the idler sprocket and lower timing chain using the mating marks and the paint marks made during the removal process. CAUTION:

Related Content:

remove nissan quest tension timing, 2000 cadillac deville engine diagram, timing marks in 07 kia optima, timing chain tensioner removal 04 quest, timing chain for lincoln ls 04 b8, nissan quest timing chain tensioner replacement, mazda 6 timing marks, chrysler2 7 timing com, 2011 escape timing belt, 2005 gmc envoy timing chain

2000 Dodge Intrepid Timing Chain Service and Repair Manual

0

Filed Under (Dodge Manuals) by admin on 21-11-2011

download
REMOVAL 1.Remove upper intake manifold. 2.Remove cylinder head covers, crankshaft damper, and timing chain cover. CAUTION: When aligning timing marks, always rotate engine by turning the crankshaft. Failure to do so will result in valve and/or piston damage. Fig. 70 3.Align crankshaft sprocket timing mark to mark on oil pump housing (Fig. 70). The mark on oil pump housing is 60° ATDC of #1 cylinder. CAUTION: When the timing chain is removed and the cylinder heads are still installed, DO NOT rotate the camshafts or crankshaft without first locating the proper crankshaft position. Failure to do so will result in valve and/or piston damage Fig. 74 4.Remove primary timing chain tensioner from right cylinder head (Fig. 74). 5.Remove camshaft position sensor from left cylinder head (Fig. 69). 6.Remove chain guide access plug from left cylinder head (Fig. 69). NOTE: When camshaft sprocket bolts are removed, the camshafts will rotate in a clockwise direction. 7.Starting with the right camshaft sprocket, remove the sprocket attaching bolts. Remove camshaft damper and sprocket (Fig. 69). 8.Remove left side camshaft sprocket attaching bolts and remove sprocket (Fig. 69). 9.Remove lower chain guide and tensioner arm (Fig. 69). 10.Remove the primary timing chain. INSTALLATION 1.Inspect all sprockets and chain guides. Replace if worn. Refer to Crankshaft Gear/Sprocket, for removal and installation procedures. 2.If removed, install right and left side short chain guides (Fig. 69). Tighten attaching bolts to 28 Nm (250 in. lbs.) 3.Align crankshaft sprocket timing mark to the mark on oil pump housing (Fig. 71). NOTE: Lubricate timing chain and guides with engine oil before installation. 4.Place left side primary chain sprocket onto the chain so that the timing mark is located in-between the two (plated) timing links (Fig. 71). 5.Lower the primary chain with left side sprocket through the left cylinder head opening

Related Content:

2006 trailblazer timing marks, diagram of a 00 lincoln ls 3 9 liter timing chain and gears, 2004 pontiac sunfire timing chain replacement, 04 ford escape timing chain settings, tdc on jaguar 4 0, sport trac timing chain replacement interval, number one cylinder cam is not near 11 o\clock why? 04 nissan quest, is crankshaft position sensor removed when replacign timing chain on 2001 durango, installing timing chain on 2000 dodge ram 1500, how to replace the timing chain on a 2004 maxima 3 5

1998 Chevrolet Blazer Engine Oil Cooler Hose/ Pipe Removal And Installation Manual

0

Filed Under (Chevrolet Manuals) by admin on 22-05-2012

download
Removal Procedure 1. Remove the steering linkage shield. Refer to Steering Linkage Shield Replacement in Steering Linkage. Important: Have a drain pan ready for the engine oil to drain into. 2. Remove the bolt attaching the engine oil cooler lines to the remote (frame mounted) oil filter adapter. 3. Remove and discard the seals. 4. Remove the engine oil cooler line retaining rings from the engine oil cooler line quick connectors at the radiator engine oil cooler inlet and outlet. Follow the next two steps for the proper retaining ring removal procedure. 5. Using a bent-tip screwdriver or equivalent, pull on one of the open ends of the retaining ring in order to rotate the retaining ring. 6. Rotate the retaining ring around the quick connector until the retaining ring is out of position and can be completely removed. Discard the retaining rings. 7. Remove the engine oil cooler lines from the quick connectors at the radiator engine oil cooler inlet and outlet. Pull the lines straight out from the connectors. 8. Remove the remote engine oil filter lines support clamp bolt. Important: Have a drain pan ready for the engine oil to drain into. 9. Remove the bolt attaching the remote engine oil filter lines to the remote (frame mounted) engine oil filter adapter. 10. Hold the remote engine oil filter lines below the remote engine oil filter lines (engine mounted) adapter to drain the engine oil. 11. Remove and discard the seals. 12. Remove the bolt attaching the remote engine oil filter lines to the remote engine oil filter lines (engine mounted) adapter. 13. Remove and discard the seals. 14. Clean all of the components in a suitable solvent, and dry them with compressed air. 15. Inspect the fittings, the connectors, the cooler lines, the cooler, the filter lines, and the remote filter adapter for damage, distortion, or restriction. Replace parts as necessary. 16. Flush the engine oil cooler, the engine oil cooler lines, the remote engine oil filter adapter, and the remote engine oil filter lines with the same type of engine oil normally circulating through the engine. Installation Procedure

Related Content:

replace oil cooker 3406 cat motor, 2005 ford escape 2 3liter oil dipstick housing seal, clips for blazer oil cooling lines, oil cooler on 3406 cat how to change, 2006 chevy trailblazer engine removal, removing the oil pan on a 2008 impala 3 5, 2001 a4 oil cooler lines, 2006 impala oil filter housing gasket, 2012 kia srento a/c condensor drain line drawing, how many man hours to replace engine suburban 2007 for

TIMING BELT COMPONENTS FOR REMOVAL AND INSTALLATION MANUAL

0

Filed Under (More Manuals) by admin on 13-07-2012

download
TIMING BELT REMOVAL 1. DRAIN ENGINE COOLANT 2. REMOVE ENGINE UNDER COVER 3. REMOVE AIR CLEANER DUCT 4. REMOVE DRIVE BELT, FAN WITH FLUID COUPLING AND WATER PUMP PULLEY (See step 5 in water pump removal in Cooling System) 5. REMOVE RADIATOR ASSEMBLY (See steps 5 and 6 in radiator removal in Cooling System) 6. REMOVE NO.3 TIMING BELT COVER (a) Remove the oil filler cap. (b) Using a 5 mm hexagon wrench, remove the 6 bolts and belt cover. 7. REMOVE NO.2 TIMING BELT COVER Using a 5 mm hexagon wrench, remove the 3 bolts, belt cover and gasket. If you are unable to loosen the bolt on the right because the PS pump pulley interferes with the hexagon wrench, first remove the pulley as follows. (a) Using SST to hold the pulley, remove the nut. SST 09960-10010 (b) Remove the pulley. 8. REMOVE DRIVE BELT TENSIONER Remove the 3 bolts and tensioner. – ENGINE ENGINE MECHANICAL EG-19 9. SET NO.1 CYLINDER TO TDC/COMPRESSION (a) Turn the crankshaft pulley, and align its groove with timing mark “0″ of the No.1 timing belt cover. NOTICE: Always turn the crankshaft clockwise. (b) Check that the timing marks of the camshaft timing pulleys are aligned with the timing marks of the No.4 timing belt cover. If not, turn the crankshaft 1 revolution (360?). 10. REMOVE TIMING BELT FROM CAMSHAFT TIMING PULLEYS HINT (Re-using timing belt): Place matchmarks on the timing belt and camshaft timing pulleys as shown in the illustration. (a) Alternately loosen the 2 bolts, and remove them, the tensioner and dust boot. (b) Disconnect the timing belt from the camshaft timing pulleys. 11. REMOVE CAMSHAFT TIMING PULLEYS Using SST, remove the bolt for the timing pulley. Remove both timing pulleys. SST 09960-10010 (09962-01000, 09963-01000) 12. REMOVE CRANKSHAFT PULLEY (a) Using SST, loosen the pulley bolt. SST 09213-70010, 09330-00021 (b) Remove the SST and pulley bolt

Related Content:

ford E250 rear vaporline to carben canester diagram, 2008 mazda 2 3 timing procedure, 1999 honda odyssey repair manual pdf, NTC350 drive gear remova, remove head timing cover on a 96 altima, remove timing cover 2005 Nissan Altima 2 5 L, removing pulleys timing belt cover 3000 gt, set timing on 2005 aveo, timing marks for 2005 nissan altima 2 5, Variable Camshaft Timing Solenoid Picture

1999 Volkswagen New Beetle GL timing belt replacement manual

0

Filed Under (Volkswagen Manuals) by admin on 21-06-2012

download
REMOVAL & INSTALLATION NOTE: For 2004, manufacturer does not provide a timing belt replacement interval. CAUTION: This application is an interference engine. Do not rotate camshaft or crankshaft when timing belt is removed, or engine damage may occur. NOTE: Engine code AEG is stamped into machined pad on front of cylinder block above crankcase breather, near cylinder head mating surface. See Fig. 1 . For all other 2.0L engines, engine code is stamped on transmission mating flange at the rear of the engine. See Fig. 2 . For all engines, code can also be found on the vehicle data plate and on a sticker on the timing belt cover. Fig. 2: Locating Engine Identification Code (AVH, AZG, BDC & BEV) Courtesy of VOLKSWAGEN UNITED STATES, INC. TIMING BELT Removal (AEG, AVH, AZG, BEV & BDC Engine Codes) 1. Remove right hand insulation tray from engine compartment. Remove engine cover. Rotate serpentine belt tensioner clockwise to relieve belt tension. Remove serpentine belt. See Fig. 3 . Lock in place using Mandrel (T10060) or a drift. Fig. 3: Releasing Serpentine Belt Tensioner Courtesy of VOLKSWAGEN UNITED STATES, INC. 2. Remove serpentine belt tensioner assembly. See Fig. 4 . Turn crankshaft to TDC position. See Fig. 5 . Align TDC marks visible in bellhousing access hole. See Fig. 6 . Remove upper timing belt cover. Ensure camshaft sprocket timing mark aligns with mark on rear cover. See Fig. 5 . 3. Support engine from above or below with floor jack to take engine weight off of mounts. Remove coolant reservoir and set aside. On Golf and Jetta, remove power steering reservoir (hoses attached), and set aside. On New Beetle, pull off EVAP hoses at EVAP canister and throttle valve housing. 4. On all models, remove engine mount from timing belt end of engine. See Fig. 7 . Remove crankshaft pulley from crankshaft sprocket. It is NOT necessary to remove center bolt (center bolt is torque-to-yield type that must be replaced if removed). 5. Remove timing belt covers. Remove engine support from front of engine. See Fig. 4

Related Content:

2004 volkswagen jetta timing belt replacement interval

CHAIN SUB-ASSEMBLY (2AZ-FE) REMOVAL AND INSTALLATION MANUAL

0

Filed Under (More Manuals) by admin on 17-05-2012

download
INSTALL CHAIN TENSIONER SLIPPER a. Install the chain tensioner slipper with the bolt. Torque: 19 Nm (194 kgf-cm, 14 ft. lbs.) Zoom Sized for Print 36. INSTALL TIMING CHAIN GUIDE a. Install the timing chain guide with the bolt. Torque: 9.0 Nm (92 kgf-cm, 80 inch lbs.) Zoom Sized for Print 37. INSTALL CRANKSHAFT POSITION SENSOR PLATE NO.1 a. Install the sensor plate with the “F” mark facing forward. 38. INSTALL TIMING GEAR CASE OR TIMING CHAIN CASE OIL SEAL a. Apply multipurpose grease to a new oil seal lip. NOTICE: Keep the lip free of foreign objects. Zoom Sized for Print b. Using SST and a hammer, tap in the new oil seal until its surface is flush with the timing chain cover edge. SST 09223-22010 39. INSTALL TIMING CHAIN OR BELT COVER SUB-ASSEMBLY a. Remove any old packing material and be careful not to drop any oil on the contact surfaces of the timing chain cover, cylinder head and cylinder block. Zoom Sized for Print b. Apply a continuous bead of seal packing (Diameter 2.0 mm (0.079 inch) ) as shown in the illustration. Seal packing: Part No. 08826-00080 or equivalent Zoom Sized for Print NOTICE: • Remove any oil from the contact surface. • Install the chain cover within 3 minutes of applying seal packing. • Do not put in engine oil for at least 2 hours after installing the chain cover. c. Apply a continuous bead of seal packing as shown in the illustration. Seal packing: Part No. 08826-00080 or equivalent NOTICE: • Remove any oil from the contact surface. • Install the chain cover within 3 minutes of applying seal packing. • Do not put in engine oil for at least 2 hours after installing the chain cover. Zoom Sized for Print d. Install the timing chain cover with the 14 bolts and 2 nuts. Torque: 9.0 Nm (92 kgf-cm, 80 inch lbs.) for bolt A 25 Nm (255 kgf-cm, 18 ft. lbs.) for bolt B 55 Nm (561 kgf-cm, 41 ft. lbs.) for bolt C 43 Nm (438 kgf-cm, 32 ft. lbs.) for bolt D 11 Nm (112 kgf-cm, 8 ft. lbs.) for nut

Related Content:

2002 nissan altima timing marks how many revolutions, bolt pattern for the timing cover of 5 4L triton, Ford 5 0 Timing Cover bolt diagram, Seal Packing 08826 00080

Related Content:

4D35 engine repair manual, 6m70 wiring diagram, 2000 Nissan sentra 1 8 engine bolt torque diagram, so5d engine repair manual, so5d engine, TOYOTA SO5D SERVICE MUNAL, what causes damage to a flywheel on a 2004 yukon, SO5D OBD ll Code, 2005 chevy impala motor diagram, Position of sensors in mitsubishi 4m 51 engine