torque for gmc yukon caliper bolts

You search PDF repair manual about torque for gmc yukon caliper bolts, if there are search results will appear below. If search results do not exist, please search by others keyword.



  torque for gmc yukon caliper bolts Direct Download speed 5432 Kb/s

  torque for gmc yukon caliper bolts Full Version speed 8172 Kb/s



2004 Chrysler Pacifica DISC BRAKE SHOES Removal And Installation Manual

0

Filed Under (Chrysler Manuals) by admin on 13-05-2011

download
DISC BRAKE SHOES Removal (Front) 1. Remove master cylinder fluid reservoir cap. 2. Raise and support vehicle. 3. Remove tire and wheel assembly. 4. Place appropriately sized C-clamp over brake caliper, placing screw-drive head against outboard shoe and hook against rear of caliper. Slowly tighten screw-drive retracting caliper pistons into bores and brake outboard brake shoe free from caliper fingers. See Fig. 22 . Remove C-clamp. 5. Once outboard shoe is free from caliper fingers, slide caliper inboard on guides providing clearance between the rotor and inboard brake shoe. 6. Slide an appropriate prying tool through center opening in top of caliper behind brake shoe between 2 caliper pistons. Use care not to come in contact with pistons or dust boots potentially damaging them. Pry against rear of inboard brake shoe braking it free from caliper pistons. 7. Remove the 2 brake caliper guide pin bolts. See Fig. 23 . 8. Remove disc brake caliper from brake adapter and hang out of way using wire or a bungee cord. Use care not to overextend brake hose when doing this. 9. Remove brake shoes from disc brake caliper adapter. See Fig. 27 . 10. Install master cylinder fluid reservoir cap. 2. Install disc brake caliper over brake shoes on brake caliper adapter. See CALIPER . 3. Align guide pin bolt holes with guide pins and install caliper guide pin bolts. See TORQUE SPECIFICATIONS . 4. Install tire and wheel assembly. See TORQUE SPECIFICATIONS . 5. Lower vehicle. 6. Pump brake pedal several times to seat shoes to caliper and brake rotor. 7. Check and fill brake fluid level as necessary. See CHECKING & FILLING under BRAKE FLUID in SERVICE. 8. Road test vehicle making several stops to wear off any foreign material on brakes and to seat brake shoes. Removal (Rear) 1. Raise and support vehicle. 2. Remove both rear tire assemblies from vehicle. 3. Remove 2 caliper guide pin bolts. 4. Remove the 2 caliper guide pin bolts. See Fig. 24 . 5. Remove caliper from caliper adapter. See CALIPER . 6. Remove outboard brake shoe by pushing shoe away from caliper fingers, dislocating locating pins built into shoe backing plate from holes in caliper fingers, then sliding brake shoe down and off of brake caliper. See Fig. 28 . 7. Pull inboard brake shoe away from caliper piston, dislocating retaining clip from cavity in piston. Remove inboard shoe. NOTE: In some cases, it may be necessary to retract caliper piston in its bore a small amount in order to provide sufficient clearance between shoes and rotor to easily remove caliper from knuckle. This can usually be accomplished before guide pin bolts are removed, but grasping rear of caliper and pulling outward working with guide pins, thus retracting piston. DO NOT push on piston directly as it may get damaged.

Related Content:

4L80E Troubleshooting Guide, bench bleeding brake mc 97 ford ranger pdf, www motorcraftservice com owners guide, 2006 honda accord brake caliper torque, v reader repair, lucerne brake caliper torque spec, Mazda 6 Shop Manual PDF, proper torque for chevy truck pitman arm replacement 2004 avalanche, rear brake caliper removal on 2010 ford f-150, replacing caliper pin 2007 sienna

1999 Honda Civic EX TORQUE SPECIFICATIONS

0

Filed Under (Honda Manuals) by admin on 04-02-2012

download
TORQUE SPECIFICATIONS Application Ft. Lbs. (N.m) A/C Compressor Bracket-To-Engine Bolts 33 (45) A/C Compressor-To-Bracket Bolts 18 (24) A/C Idler Pulley Bracket Bolts 8-mm 18 (24) A/C Idler Pulley Center Nut 33 (45) Battery Tray 18 (24) Camshaft Holder Bolts DOHC 8-mm Bolts 20 (27) SOHC 8-mm Bolts 15 (20) Camshaft Pulley Bolt DOHC 41 (56) SOHC 27 (37) Catalytic Converter Flange Nuts 25 (34) Clutch Slave Cylinder Line/Hose Bracket 8-mm Bolts 18 (24) Clutch Slave Cylinder Mounting 8-mm Bolts 18 (24) Connecting Rod Bearing Cap Nuts DOHC 30 (40) SOHC 23 (31) Crankshaft Pulley Bolt DOHC 130 (177) SOHC (1) Cylinder Head Bolts DOHC First Step (Bolts 1-10) 22 (29) Second Step 61 (83) SOHC First Step (Bolts 1-10) 15 (20) Second Step (Bolts 1-10) 36 (49) Thrid Step (Bolts 1-10) 49 (67) Forth Step (Bolts 1 & 2) 49 (67) Distributor Mount Bolt 18 (24) Drive Plate Bolts (A/T Or CVT) 54 (74) EGR Valve Nuts 15 (20) Engine Coolant Drain Plug 58 (79) Engine Mounts (2) Transaxle Mount 10-mm Bolts 12-mm Bolts/Nuts 47 (64) 12-mm Through-Bolt 54 (74) Side Engine Mount 10-mm Nuts/Bolts 40 (54) Engine Upper Mount Bracket 74 (54) Rear Mount Bracket 12-mm Bolts 43 (59) 14-mm Bolts 61 (83) Left Front Mount 10-mm Bolts 33 (44) 12-mm Bolts 43 (59) Right Front Mount 10-mm Bolts 33 (44) 12-mm Bolts 47 (64) Engine Oil Drain Plug 33 (45) Engine Front & Rear Stiffeners 8-mm Bolts 18 (24) 10-mm Bolts 33 (44) 12-mm Bolts 42 (57) Exhaust Manifold Bracket Bolt 8-mm 18 (24) 10-mm 33 (45) Exhaust Manifold Cover 8-mm Bolts 18 (24) Exhaust Manifold-To-Cylinder Head Nuts (3) 23 (31) Exhaust Pipe Bracket 8-mm Nuts (3) 12 (16) Exhaust Pipe Flange 8-mm Bolts (3) 16 (22) Exhaust Pipe-To-Manifold/TWC (3) D16Y5 & D16Y7 Engines 25 (33) D16Y8 & B16A2 Engines 40 (54) Flywheel Bolts (M/T) 87 (118) Fuel Filter Banjo Bolt 25 (34) Generator Adjustment Lock Bolt 18 (24) Generator Bracket-To-Engine Bolts 33 (45) Heated Oxygen Sensor (HO2S) 33 (45) Inspection Hole Sealing Bolt (VTEC) 15 (20) Intake Air Control (IAC) Valve Bolts D16Y5 Engine 16 (22) D16Y8 Engine 18 (24) Idler Pulley Bracket Bolt DOHC

Related Content:

pontiac vibe head torque secuensia, 1999 honda civic door bolt torque specifications, tork settings for fd 42 engine, nuts&bolts service, j35 honda bolt pattern transmission, how to rebuild a saturn 1 9 sohc, honda generator bolt torque spec, head bolt torque specifications 2000 buick century, fd42 manifold gasket, D16y8 cam removal sequence

2008 Ford Taurus AWD V6-3.5L – Rear Brake Pads Removal And Installation Manual

0

Filed Under (Ford Manuals) by admin on 25-06-2012

download
Removal WARNING: Do not use any fluid other than clean brake fluid meeting manufacturer’s specification. Additionally, do not use brake fluid that has been previously drained. Following these instructions will help prevent system contamination, brake component damage and the risk of serious personal injury. WARNING: Carefully read cautionary information on product label. For EMERGENCY MEDICAL INFORMATION seek medical advice. In the USA or Canada on Ford/Motorcraft products call: 1-800-959-3673. For additional information, consult the product Material Safety Data Sheet (MSDS) if available. Failure to follow these instructions may result in serious personal injury. CAUTION: Brake fluid is harmful to painted and plastic surfaces. If brake fluid is spilled onto a painted or plastic surface, immediately wash it with water. CAUTION: Do not allow the brake fluid to come in contact with the adhesive backing on the brake pads. If brake fluid is spilled onto the brake pads, new pads must be installed. CAUTION: Use only specified brake parts cleaner. Use of other cleaners may leave a residue on the brake caliper preventing the brake pads adhesive surface from bonding with the brake caliper. 1. Remove the wheel and tire. 2. Check the brake fluid level in the brake fluid reservoir. * If required, remove fluid until the brake master cylinder reservoir is half full. 3. Remove the brake caliper bolts. 4. CAUTION: Do not use the brake caliper sight hole to retract the pistons as this may damage the pistons and boots. CAUTION: Do not allow the caliper to hang from the brake hose or damage to the hose may occur. CAUTION: Care must be taken when servicing rear brake components without disconnecting the parking brake cable from the brake caliper lever. Carefully position the caliper aside using a suitable support or damage to the parking brake cable end fittings may occur. Using hand force and a rocking motion, separate the brake caliper from the anchor plate. Position the brake caliper aside. * Support the caliper with mechanic’s wire. 5. CAUTION: When the brake pads are separated from the brake caliper , new brake pads must be installed to prevent brake noise. The brake pads are one-time use only. Remove and discard the brake pads and spring clips from the brake caliper anchor plate. 6. NOTE: Do not remove the anchor plate guide pins. The guide pins are press fit to the brake caliper anchor plate. If the guide pins are damaged a new anchor plate must be installed. Inspect the brake caliper anchor plate assembly. * Check the guide pins and boots for binding or damage. * Install a new brake caliper anchor plate if it is worn or damaged. Installation 1. NOTE: To move the piston back into the caliper, the LH piston is turned clockwise and the RH piston is turned counterclockwise. NOTE: A moderate to heavy force toward the caliper piston must be applied. If sufficient force is not applied, the internal park brake mechanism clutch cone will not engage and the piston will not compress. Using the special tool (or equivalent such as OTC tool 7317A), compress the brake caliper piston into its cylinder. 2. Clean the residual adhesive from the brake caliper fingers and pistons using the specified brake parts cleaner. 3. CAUTION: Do not allow grease, oil, brake fluid or other contaminants to contact the brake pad or caliper mating surface or damage to components may occur. Do not install contaminated pads. NOTE: Install all the new hardware supplied with brake pad kit. Install the new spring clips and brake pads. 4. Position the brake caliper and install the 2 bolts. * Tighten to 29 Nm (21 lb-ft). 5. If necessary, fill the brake fluid reservoir with clean, specified brake fluid. 6. With the vehicle engine running, apply 89-133 N (20-30 lb) of pressure on the brakes for approximately one minute, to make sure the brake pads adhere to the caliper before any contamination can be introduced. 7. Test the brakes for normal operation.

Related Content:

diagram of a 2004 chev thoe break line sysetm, stoplightswitch1997surburban, rear disk brake assembly on 2000 Saturn, 2002 ford ranger brake bleeding procedure, front brake line diagram on 2004 tahoe, isuzu npr brake booster removal instruction, isuzu npr brake adjustment, hummer h3 brake job, 2000town country brake diagram from Proportioning valve, standard brake fluid for 2006 chevy aveo

2000-2004 Honda Insight IMA System Indicator On With IMA DTC 77 REPAIR PROCEDURE

0

Filed Under (Honda Manuals) by admin on 16-01-2012

download
PROBLEM The IMA system indicator comes on and IMA DTC 77 (P1447) (battery module deterioration) or DTC 78 (P1449) (battery module deterioration) is set. CORRECTIVE ACTION Replace the battery module. If needed, replace the motor control module (MCM), the battery condition monitor (BCM), or both INSPECTION PROCEDURE 1. Turn the ignition switch to LOCK (0). 2. Remove the cargo floor mat (see page 20-44 of the 2000-04 Insight Service Manual). (In ISIS, use the keyword FLOOR MAT , and select Interior Trim Removal/Installation – Cargo Area from the list.) 3. Remove the battery module switch cover (two bolts), then remove the locking cover from the switch. 4. Flip the battery module switch to OFF . Reinstall the locking cover. 5. Wait at least 5 minutes to let the capacitors in the system discharge. 6. Remove the right trunk shelf support (five clips and two bolts). 7. Remove the six mid-frame cover bolts. Remove the intelligent power unit (IPU) lid (17 bolts). 8. Measure the voltage at the junction board terminals. There should be 30 V or less . If you read more than 30 V , there is a problem in the circuit; do the DTC troubleshooting first. SWITCH COVER LOCKING COVER BOLTS LOCKING COVER BATTERY MODULE SWITCH IPU LID RIGHT TRUNK SHELF SUPPORT BOLTS (17) CLIPS CLIPS BOLTS ON JUNCTION BOARD TERMINALS REPAIR PROCEDURE 1. Remove the battery module from the vehicle (see page 12-113 of the service manual). (In ISIS, use the keyword BAT MOD , and select Battery Module Removal/Installation from the list.) 2. Remove the lifting tool from the battery module. 3. Remove the mounting bolts for the MCM and the BCM (eight total). Unplug the electrical connectors (five for the MCM and three for the BCM), then remove the modules. 4. Install the MCM and the BCM in the new battery module. Use the original MCM and BCM if no replacement was needed; otherwise, use the appropriate replacement parts. Torque the mounting bolts to 9.8 N·m (7.2 lb-ft) . 5. Install the lifting tool on the battery module. 6. With someone to help you, carefully lift the battery module into the vehicle, and set it down into position. Remove the lifting tool. 7. Plug in the connectors, and install the Y condenser harness. Then install the mounting bolts. Torque the bolts to 24 N·m (17 lb-ft) . 8. Install the battery module air duct. Torque the bolt to 9.8 N·m (7.2 lb-ft) . 9. Connect the high voltage cables to the junction board. Torque the bolts to 9.8 N·m (7.2 lb-ft) . 10. Install the front and rear IPU braces and the mid- frame. Torque the bolts to 9.8 N·m (7.2 lb-ft) . Model Year MCM Part Number Replacement Part Number M/T Models 2000-01 1K000-PHM-000 thru 1K000-PHM-050 1K000-PHM-060 (H/C 7071525)

Related Content:

020139007 service bulletin, battery restoration procedure, servicing a battery module honda insight

1995 Ford Truck F 150 2WD Pickup New Cylinder Head Bolt Repair Manual

0

Filed Under (Ford Manuals) by admin on 20-02-2012

download
ORQUE SPECIFICATIONS FOR THE NON-FLANGED STANDARD HEX HEAD BOLTS, TIGHTEN IN TWO (2) STEPS AS FOLLOWS: 1. Tighten all bolts in sequence (Figure 2) to 75-88 N-m (55-65 lb.ft.). 2. Tighten all bolts in sequence (Figure 2) to 88-98 N-m (65-72 lb.ft.). FOR ALL TORQUE TO YIELD HEX HEAD BOLTS, TIGHTEN IN THREE (3) STEPS AS FOLLOWS: 1. Tighten all bolts in sequence (Figure 2) to 34-47 N-m (25-35 lb.ft.). 2. Tighten all bolts in sequence (Figure 2) to 61-75 N-m 45-55 lb.ft.). 3. Tighten all bolts in sequence (Figure 2) an additional 1/4 turn (85-95 degrees). NOTE: WHEN THE CYLINDER HEAD BOLTS HAVE BEEN TIGHTENED FOLLOWING THESE PROCEDURES, IT IS NOT NECESSARY TO RETIGHTEN THE BOLTS AFTER EXTENDED OPERATION. CAUTION: TORQUE-TO-YIELD CYLINDER HEAD BOLTS MUST BE REPLACED WITH NEW BOLTS. DO NOT REUSE TORQUE-TO-YIELD BOLTS. TORQUE-TO-YIELD BOLTS MAY ONLY BE USED ONE (1) TIME. PART NUMBER PART NAME F3ZZ-6065-E Cylinder Head Bolt

Related Content:

1999 2 5 ford ranger head bolt torque, D-17 manfold bolt torqe, ranger 1999 3 0 head torque diagram, torque angle specs 3100 1998 buick, torque sequence 300m 3 5 heads

FRONT WHEEL SPEED SENSOR CORROSION REPAIR MANUAL

0

Filed Under (More Manuals) by admin on 08-07-2012

download
1999-2002 CHEVROLET SILVERADO 2000-2002 CHEVROLET TAHOE, SUBURBAN 2002 CHEVROLET AVALANCHE 1999-2002 GMC SIERRA 2000-2002 GMC YUKON, YUKON XL LOCATED IN THE SEVERE CORROSION AREAS LISTED BELOW Service Procedure The following procedure provides instructions for repairing a corrosion condition where the front wheel speed sensor mounts on the front wheel bearing assembly. 1. Raise the vehicle on a suitable hoist and support as necessary. 2. Remove both front tires and wheels. 3. Compress the front brake caliper pistons. 3.1. Install a large C-clamp over the top of the caliper housing and against the back of the outboard pad. 3.2. Slowly tighten the C-clamp until the pistons are pushed completely into the caliper bores. 3.3. Remove the C-clamp from the caliper. Important: It is not necessary to remove the front brake caliper from the bracket when removing the bracket in the next step. 4. Remove the two bolts that attach the front brake caliper mounting brackets to the knuckle. Notice: Support the brake caliper with heavy mechanic’s wire, or equivalent, whenever it is separated from its mount, and the hydraulic flexible brake hose is still connected. Failure to support the caliper in this manner will cause the flexible brake hose to bear the weight of the caliper, which may cause damage to the brake hose and in turn may cause a brake fluid leak. 5. Remove the brake caliper and bracket as an assembly and support it with heavy mechanic’s wire or equivalent. DO NOT disconnect the hydraulic brake flexible hose from the caliper. 6. Mark the relationship of the rotor to the bearing hub. 7. If equipped, remove the rotor retaining push nuts from the wheel studs

Related Content:

1999 gmc suburban ac repair manual, break caliper removal on 2002 silverado

2004 Ford Expedition/ Navigator Brake Pads REMOVAL AND INSTALLATION MANUAL

0

Filed Under (Ford Manuals) by admin on 19-06-2012

download
Removal 5. NOTE: Verify if the anchor housing spring has 1. CAUTION: Install a new lining if worn 1 end with 2 tabs. If yes, the LH side anchor to or past the specified thickness above the housing spring must be installed with the metal backing plate or rivets. Install new 2-tabbed end in the upper brake caliper cavity. pads in complete axle sets. For the LH brake caliper, release the lower If necessary, using a suitable suction device, portion of the anchor housing spring. remove the brake fluid in the master cylinder •Apply force at the center of the anchor reservoir until it is half filled. housing spring and pull outward at the bottom of the anchor housing spring to 2. Remove the wheel and tire assembly. For remove it from the lower brake caliper additional information, refer to Section 204-04. cavity. 3. Inspect the brake pads for wear or contamination. 4. CAUTION: If the anchor housing spring is to be reused, do not force the anchor housing spring off the brake caliper. Do not install a damaged anchor housing spring. Remove the anchor housing spring. REMOVAL AND INSTALLATION (Continued) 6. Rotate the spring upward then remove it from the brake caliper. 9. NOTE: Do not allow the brake caliper to hang from the brake hose. Remove the brake caliper. 7. NOTE: On the RH side, the anchor housing 1 Remove the zero-drag spring. spring must be installed with the 2-tabbed end in the lower brake caliper cavity. The 2 Remove and discard the brake illustration below shows the anchor housing caliper-to-anchor plate bolts, guide pins and spring end with 2 tabs. boots. For RH brake caliper, release the upper portion of the anchor housing spring. •Apply force at the center of the anchor housing spring and pull outward at the top of the anchor housing spring to remove it from the upper brake caliper cavity. 10. Remove the brake pads from the brake caliper. 11. NOTE: Use a wood block or used brake pad to protect the brake caliper piston boots. Compress the brake caliper pistons. 8. Rotate the spring downward then remove it from the brake caliper.

Related Content:

toyata vios caliper spring clips

2004 Ford Expedition/ Navigator Brake Pads REMOVAL AND INSTALLATION

0

Filed Under (Ford Manuals) by admin on 26-01-2011

download
1. CAUTION: Install a new lining if worn 1 end with 2 tabs. If yes, the LH side anchor to or past the specified thickness above the housing spring must be installed with the metal backing plate or rivets. Install new 2-tabbed end in the upper brake caliper cavity. pads in complete axle sets. For the LH brake caliper, release the lower If necessary, using a suitable suction device, portion of the anchor housing spring. remove the brake fluid in the master cylinder •Apply force at the center of the anchor reservoir until it is half filled. housing spring and pull outward at the bottom of the anchor housing spring to 2. Remove the wheel and tire assembly. For remove it from the lower brake caliper additional information, refer to Section 204-04. cavity. 3. Inspect the brake pads for wear or contamination. 4. CAUTION: If the anchor housing spring is to be reused, do not force the anchor housing spring off the brake caliper. Do not install a damaged anchor housing spring. Remove the anchor housing spring. REMOVAL AND INSTALLATION (Continued) 6. Rotate the spring upward then remove it from the brake caliper. 9. NOTE: Do not allow the brake caliper to hang from the brake hose. Remove the brake caliper. 7. NOTE: On the RH side, the anchor housing 1 Remove the zero-drag spring. spring must be installed with the 2-tabbed end in the lower brake caliper cavity. The 2 Remove and discard the brake illustration below shows the anchor housing caliper-to-anchor plate bolts, guide pins and spring end with 2 tabs. boots. For RH brake caliper, release the upper portion of the anchor housing spring. •Apply force at the center of the anchor housing spring and pull outward at the top of the anchor housing spring to remove it from the upper brake caliper cavity. 10. Remove the brake pads from the brake caliper. 11. NOTE: Use a wood block or used brake pad to protect the brake caliper piston boots. Compress the brake caliper pistons. 8. Rotate the spring downward then remove it from the brake caliper.

Related Content:

installing break pads on 2004 exped

Toyota Prius GEN 2 Driver Side Extender Guide Installation Manual

0

Filed Under (Toyota Manuals) by admin on 01-04-2012

download
Installation Guide: Thank you for purchasing extendmyseat brackets. Please follow the directions carefully and within 30 minutes you will be loving your new seats. Inventory in Box: 2- extendmyseat brackets 4- black 3/8 stainless bolts What you will need for assembly: 1- socket wrench 1- 9/16 socket 1- Metric 13 socket (Prius uses metric bolts however a 9/16 works) 1- 9/16 flat wrench 1- protective eyewear Step 1- Remove the 2 Black extendmyseat brackets from the packaging and locate the 4 black 3/8″ provided bolts. Step 2- Go to your vehicle with a socket wrench and a 9/16 socket, eye protection and your keys. Remember to turn off your cabin lights. Step 3- Locate the 4 factory bolts that hold your drivers seat to the vehicle. Take your socket wrench and loosen the 4 factory bolts. (2 in the front and 2 behind your seat, go to rear seat to locate) Remove the 2 plastic guards to locate the 2 rear factory bolts. Remove the 4 factory bolts and set them aside Step 4- Unplug the 3 factory cables plugged into your car seat under the front portion of the seat. No tools required. Remember to plug these back in after you have completed the install. Step 5- Remove your car seat carefully. (Approx weight is 25 pounds) Step 6- Place your driver’s seat on a bench or on the ground on a clean sheet, towel etc…(don’t want to et it dirty) Step 7- Grab the 2 extendmyseat brackets Step 8- Lay down the 2 black brackets inside your vehicle and line up the 4 hole location. Start with the front 2 holes. Finger tighten the 2 front factory bolts into the 2 front EMS bracket holes. Now line up the 2 rear holes and finger tighten the 2 remaining factory bolts. Finger tighten all 4 holes with seat still out o f the Step 9- place drivers seat back into the vehicle. Line up drivers seat front holes with EMS front holes. Finger tighten front 2 feet with provided EMS bolts. Press seat lever and slide seat to the most up front position. Go to back seat and screw down the remaining 2 factory feet with the factory bolts. Then the 2 remaining EMS bolts into the remaining 2 EMS holes. Place the 3rd EMS bolt into the (B) bracket and the 4th and final bolt into the (A) bracket closest to the outside of the vehicle. Step 10- ONCE ALL 8 BOLTS ARE FINGER TIGHT; NOW COMPLETE THE INSTALLATION BY SECURING THE 8 BOLTS (4 factory and 4 EMS). CHECK TO MAKE SURE ALL 8 BOLTS ARE NOW TIGHT AND SECURE.

Related Content:

prius2 extendmyseat

FORD E450 CUTAWAY OWNERS MANUAL

0

Filed Under (Ford Manuals) by admin on 21-05-2012

download
DRIVER SIDE DISASSEMBLY 1. With weight taken off the rear springs, as noted in pre-installation checklist, remove the front and rear bolts from the leaf spring. 2. Remove existing U-bolts and U-bolt plate that attach the axle to the leaf spring . Remove the leaf spring from the axle. 3. Remove the front spring hanger bracket , rear leaf spring hanger bracket, and any overload spring brackets . See Figure 2-1. These can be removed by grinding, or air chiseling, the heads off the factory-installed rivets, and using a hammer and punch to remove remainder of the rivet. See Figure 2-2. 3. Remove the OEM shock absorbers and retain the lower mounting fastener for later use. 4. Cut the exhaust as it bends downward after the axle, at its most vertical and straight section. See Figures 2-3 & 2-4. Save the cut-off portion for use in Section 9. Remove the rear exhaust hanger from the frame. CAUTION: Be careful that the leaf spring does not spring out of its hanger, or off the frame. FIG. 2-4 FIG. 2-1 FRONT HANGER BRACKET FIG. 2-2 LEAF SPRING REAR HANGER BRACKET FIG. 2-3 CUT HERE FOR EXHAUST MODIFICATION 6 3. DRIVER SIDE ASSEMBLY 1. Review Figure 3-1 & Figure 11-2 to acquaint yourself with the various parts of the UltraRide suspension. 2. Fasten the Front Hanger to the frame using the (4) 7/16 x 1 1/4 UNC FLANGE BOLTS and (4) 7/16 UNC TOP LOCK FLANGE NUTS. (See Table 11-1 for appropriate Torque) . 3. Loosely secure the suspension Arm to the axle using (2) 5/8 UNF, 4.0 X 10.50 U-bolts, (4) 5/8 WASHERS, (4) 5/8 UNF HIGH NUTS, and the Arm Mount Plate. Make sure the locating pin is properly inserted into the mating hole on the axle pad and that the bottom side of the arm rests evenly on the axle pad. Note : Install the axle tube spacer between the U-bolts and Axle when installing on an E350. 4. Insert the Bolt Spacer Tube into the arm bushing and loosely fasten the Arm to the Front Hangar using (1) 3/4 X 7 UNF BOLT, (1) 3/4 UNF NUT, (2) 3/4 WASHERS, and (2) plastic wear washers. 5. Using the enclosed bolt hole template for the Upper Air Spring Mount, align the template to the frame using the appropriate rear spring hanger holes. Mark and drill three (3) new frame holes to 0.47″ on each side of the frame. Bolt the air spring bracket assembly to the frame using (5) 7/16 x 1 1/4 UNC CAPTIVE BOLTS and (5) 7/16 UNC TOP LOCK FLANGE NUTS. (See Table 11-1 for appropriate Torque) . Note : Use the correct holes designated for either the E350 or E450 chassis. See Figure 3-2. 6. Bolt the air spring to the suspension Arm using (1) 1/2 UNC JAM NUT. Make certain the air spring is not twisted or creased after tightening the nut. (See Table 11-1 for appropriate Torque) . FIG. 3-2 E450 HOLE PATTERN E350 HOLE PATTERN TEMPLATE OE REAR HANGER MOUNT HOLES FRAME FIG. 3-1 AIR SPRING ARM MOUNT PLATE AXLE TUBE SPACER WEAR WASHER TRAILING ARM U-BOLT FRONT HANGER BRACKET AIR SPRING MOUNT BRACKET 7 AFTER BOTH SIDES HAVE BEEN INSTALLED (Sections 4, 5, 6) FINISH THE FOLLOWING STEPS: 7. Tighten the Arm bushing bolts and the Arm U-bolts AFTER the suspension has been installed and brought to Design Height, in Section 9.5. (See Table 11-1 for appropriate Torque) . 8. Install the new shock absorbers using the same orientation as factory, with factory and enclosed hardware. 9. IMPORTANT: Route the brake cable away from the air spring and any other moving components. It may need to be tied, or slightly repositioned in order to accommodate this. 4. PASSENGER SIDE DISASSEMBLY 1. Repeat Section 2 for the passenger’s side of the truck. 5. PASSENGER SIDE ASSEMBLY 1. Repeat Section 3 for the passenger’s side of the truck. Double-check all fasteners for proper torque. Check all clearance points and all alignments. See Figure 5-1 for details.

Related Content:

2002 rondevious change rear spring, f150 1995 changing front leaf spring brackets, head bolts torque on 2001 2 5 ford ranger, how to replace 2000 chevy cavalier exhaust bracket, how to replace mazda 3 rear coil springs, is there a metal washer before e clip on pitman arm seal gearbox on a 1997 ford f150, tie rod end at pitman armnut torque 2000 f350 7 3l 4wd, Trailing Arm bracket for 2000 Buick Century

Related Content:

4L80E Troubleshooting Guide, bench bleeding brake mc 97 ford ranger pdf, www motorcraftservice com owners guide, 2006 honda accord brake caliper torque, v reader repair, lucerne brake caliper torque spec, Mazda 6 Shop Manual PDF, proper torque for chevy truck pitman arm replacement 2004 avalanche, rear brake caliper removal on 2010 ford f-150, replacing caliper pin 2007 sienna