Skip to content

torque specifications for intake manifold for 2002 chevy s 10

You search PDF repair manual about torque specifications for intake manifold for 2002 chevy s 10, if there are search results will appear below. If search results do not exist, please search by others keyword.

2002 Chevrolet Chevy Suburban – 4WD Intake Manifold Replacement Manual

download
Removal Procedure Important: The intake manifold, throttle body, fuel rail, and injectors may be removed as an assembly. If not servicing the individual components, remove the manifold as a complete assembly. 1. Remove the throttle body. Refer to Throttle Body Assembly Replacement in Engine Controls – 4.8L, 5.3L, and 6.0L. 2. Remove the fuel injectors. Refer to Fuel Injector Replacement in Engine Controls – 4.8L, 5.3L, and 6.0L. 3. Disconnect the following electrical connectors: 4. Remove the knock sensor harness electrical connector from the intake manifold. 5. Set the electrical harness aside. <- Back Forward -> Document ID# 738735 2002 Chevrolet Chevy Suburban – 4WD Print – Manifold absolute pressure (MAP) sensor (1) – Knock sensor (2) – Exhaust gas recirculation (EGR) valve, if equipped. 6. If equipped, remove the following EGR pipe bolts: 7. If equipped, remove the EGR pipe with valve. 8. If equipped, remove the EGR pipe gasket from the exhaust manifold If equipped with vacuum assisted brakes, remove the vacuum brake booster hose from the rear of the intake manifold.

1999 Honda Civic EX TORQUE SPECIFICATIONS

download
TORQUE SPECIFICATIONS Application Ft. Lbs. (N.m) A/C Compressor Bracket-To-Engine Bolts 33 (45) A/C Compressor-To-Bracket Bolts 18 (24) A/C Idler Pulley Bracket Bolts 8-mm 18 (24) A/C Idler Pulley Center Nut 33 (45) Battery Tray 18 (24) Camshaft Holder Bolts DOHC 8-mm Bolts 20 (27) SOHC 8-mm Bolts 15 (20) Camshaft Pulley Bolt DOHC 41 (56) SOHC 27 (37) Catalytic Converter Flange Nuts 25 (34) Clutch Slave Cylinder Line/Hose Bracket 8-mm Bolts 18 (24) Clutch Slave Cylinder Mounting 8-mm Bolts 18 (24) Connecting Rod Bearing Cap Nuts DOHC 30 (40) SOHC 23 (31) Crankshaft Pulley Bolt DOHC 130 (177) SOHC (1) Cylinder Head Bolts DOHC First Step (Bolts 1-10) 22 (29) Second Step 61 (83) SOHC First Step (Bolts 1-10) 15 (20) Second Step (Bolts 1-10) 36 (49) Thrid Step (Bolts 1-10) 49 (67) Forth Step (Bolts 1 & 2) 49 (67) Distributor Mount Bolt 18 (24) Drive Plate Bolts (A/T Or CVT) 54 (74) EGR Valve Nuts 15 (20) Engine Coolant Drain Plug 58 (79) Engine Mounts (2) Transaxle Mount 10-mm Bolts 12-mm Bolts/Nuts 47 (64) 12-mm Through-Bolt 54 (74) Side Engine Mount 10-mm Nuts/Bolts 40 (54) Engine Upper Mount Bracket 74 (54) Rear Mount Bracket 12-mm Bolts 43 (59) 14-mm Bolts 61 (83) Left Front Mount 10-mm Bolts 33 (44) 12-mm Bolts 43 (59) Right Front Mount 10-mm Bolts 33 (44) 12-mm Bolts 47 (64) Engine Oil Drain Plug 33 (45) Engine Front & Rear Stiffeners 8-mm Bolts 18 (24) 10-mm Bolts 33 (44) 12-mm Bolts 42 (57) Exhaust Manifold Bracket Bolt 8-mm 18 (24) 10-mm 33 (45) Exhaust Manifold Cover 8-mm Bolts 18 (24) Exhaust Manifold-To-Cylinder Head Nuts (3) 23 (31) Exhaust Pipe Bracket 8-mm Nuts (3) 12 (16) Exhaust Pipe Flange 8-mm Bolts (3) 16 (22) Exhaust Pipe-To-Manifold/TWC (3) D16Y5 & D16Y7 Engines 25 (33) D16Y8 & B16A2 Engines 40 (54) Flywheel Bolts (M/T) 87 (118) Fuel Filter Banjo Bolt 25 (34) Generator Adjustment Lock Bolt 18 (24) Generator Bracket-To-Engine Bolts 33 (45) Heated Oxygen Sensor (HO2S) 33 (45) Inspection Hole Sealing Bolt (VTEC) 15 (20) Intake Air Control (IAC) Valve Bolts D16Y5 Engine 16 (22) D16Y8 Engine 18 (24) Idler Pulley Bracket Bolt DOHC

Chevrolet V8 With General Duty Oval Port Cylinder Heads STREET TUNNEL RAM INTAKE MANIFOLD INSTALLATION INSTRUCTIONS

download
CAMSHAFT AND HEADERS: The Street Tunnel Ram manifold is compatible with aftermarket camshafts and headers. Use Edelbrock Torker-Plus camshaft #5062 for more low RPM torque, or the Edelbrock Performer RPM camshaft #7162 for more high RPM power. Header primary tube diameter should be 1-7/8″. This may vary depending upon your particular engine specifications. PREP AND TUNING FOR POWER: 1. Specific applications may show an increase in performance through additional carburetor tuning. 2. Aftermarket distributor curve kits and aftermarket ignitions may be used with the Street Tunnel Ram intake manifold. 3. Use modified or high performance cylinder heads such as our Performer RPM, and port match the intake manifold to the heads. 3. The engine’s compression ratio should be at least 9.5:1 to work properly with Torker-Plus or Performer RPM camshafts. INSTALLATION PROCEDURE INTAKE MANIFOLD BASE 1. Use only recommended intake gaskets set when installing this intake manifold. 2. Fully clean the cylinder head intake flanges and the engine block end seal surfaces. 3. Apply Edelbrock Gasgacinch sealant P/N 9300 to both cylinder head flanges and to the cylinder head side of the gaskets, allow to air dry, and attach the intake gaskets. 4. Do not use cork or rubber end seals. Use RTV silicone sealer instead. Apply a ¼” high bead across each block end seal surface, overlapping the intake gasket at the four corners. This method will eliminate end seal slippage. 5. Install the intake manifold hold-down bolts. Hand tighten all bolts to approximately 5 ft./lbs. to center the manifold on the engine. WARNING: There is no gasket support for the manifold under the four bolt holes which are numbered 13,14,15, and 16 in Figure 1 below. Damage to the manifold will occur if these four bolts are over tightened. Hand tighten these bolts with a 6″ box-end wrench. DONOT use a torque wrench. 6. Torque all of the remaining manifold bolts in two steps by the sequence shown in Figure 1 to 25 ft/lbs. INTAKE MANIFOLD TOP 1. Apply Edelbrock Gasgacinch sealant P/N 9300 to the gasket mating surface and install the gasket and manifold top. 2. Install and tighten the supplied hold down bolts to 15-18 ft./lbs.

2003 Honda ODYSSEY Intake Manifold Removal and Installation Manual

download
Removal 1. Remove the intake manifold cover (A) and ignition coil cover(s) (B). 1999-2001 models: 2002-2004 models: 2. Remove the evaporative emission (EVAP) canister hose (A) (1999-2001 models) or vacuum hose (A) (2002-2004 models). 3. Remove the vacuum hose(s) (B) and breather pipe (C), then remove the intake air duct (D). 1999-2001 models: 2002-2004 models: 4. Remove the throttle cable (A) and cruise control cable (B) by loosening the locknuts (C), then slip the cable ends out of the accelerator linkage. Take care not to bend the cables when removing them. Always replace any kinked cable with a new one. 5. Remove the engine wire harness connectors and wire harness clamps from the intake manifold. *Intake air temperature (IAT) sensor connector *Idle air control (IAC) valve connector *Throttle position (TP) sensor connector *Manifold absolute pressure (MAP) sensor connector *Evaporative emission (EVAP) canister purge valve connector (2002-2004 models) 6. Remove the brake booster vacuum hose (A) and positive crankcase ventilation (PCV) hose (B). 7. Remove the vacuum hoses (C) (1999-2001 models). 1999-2001 models: 2002-2004 models: 8. Remove the breather hose (A) and water bypass hoses (B), then plug the water bypass hoses. 9. Remove the EVAP canister hose (C) (2002-2004 models). 1999-2001 models:

2001 Chevy Truck S10/ T10 Blazer Intake Manifold Replacement (Upper) Removal And Installation Manual

download
Intake Manifold Replacement (Upper) Notes Intake Manifold Replacement – Upper Removal Procedure Important: The upper intake does not have to be removed to remove the lower intake manifold. 1. Disconnect the breather tube at the air cleaner outlet duct 2. Remove the air cleaner outlet duct retaining wingnut. 3. Disconnect the IAT sensor harness connector 4. Remove the air cleaner outlet duct from the throttle body. 5. Disconnect the accelerator cable from the throttle body 6. Remove the accelerator cable from the accelerator control cable bracket. 7. Disconnect the cruise control cable, if equipped from the throttle shaft and the accelerator cable bracket. 8. Disconnect the vacuum hose from the intake manifold for the vacuum tank. 9. Remove the power brake booster vacuum hose. 10. Disconnect the following electrical connectors: * The A/C compressor clutch (1) * The A/C compressor cutoff switch (5), if equipped * The Throttle Position (TP) sensor (2) * The Idle Air Control (IAC) motor (3) 11. Disconnect the following electrical connectors: * The fuel meter body assembly (1) * The Manifold Absolute Pressure (MAP) sensor(3) * The EVAP canister purge solenoid valve (2) 12. Remove the engine wire harness clip from the accelerator cable bracket. 13. Move the engine wiring harness aside. 14. Remove the accelerator cable bracket from the throttle body and the intake manifold. 15. Remove the accelerator and cruise control cable bracket from the throttle body. Leave the accelerator and cruise control cables on the bracket16. Remove the PCV valve hose assembly from the intake manifold and the valve rocker arm cover. 17. Remove the bracket for the engine wiring harness from the intake manifold stud. 18. Remove the fuel lines from the fuel meter body assembly. 19. Remove the EVAP canister purge solenoid valve.