Skip to content

torque specs for 2002 pontiac grand prix 3 8l intake

You search PDF repair manual about torque specs for 2002 pontiac grand prix 3 8l intake, if there are search results will appear below. If search results do not exist, please search by others keyword.

2002 Pontiac Grand Prix GT THERMOSTAT REPLACEMENT (3.1 L) MANUAL

download
THERMOSTAT REPLACEMENT (3.1 L) Tools Required J 38185 Hose Clamp Pliers Removal Procedure 1. Remove the air cleaner intake duct. Refer to AIR CLEANER INTAKE DUCT . 2. Partially drain the cooling system. Refer to Draining and Filling Cooling System . 3. Use the J 38185 in order reposition the hose clamp from the water outlet housing. 4. Remove the radiator inlet hose from the water outlet housing. 5. Remove the exhaust crossover pipe. Refer to EXHAUST CROSSOVER PIPE REPLACEMENT (3.1L) or EXHAUST CROSSOVER PIPE REPLACEMENT (3.8L) Fig. 74: Radiator Inlet Hose & Water Outlet Housing Courtesy of GENERAL MOTORS CORP. 6. Remove the water outlet housing bolts. 7. Remove the water outlet housing and gasket. Fig. 75: Water Outlet Housing & Bolts Courtesy of GENERAL MOTORS CORP. 8. Remove the thermostat. 9. Clean the water outlet housing mating surfaces Fig. 76: Thermostat & Water Outlet Housing Courtesy of GENERAL MOTORS CORP. Installation Procedure 1. Install the thermostat. 3. Install the water outlet housing bolts. Tighten Tighten the water outlet housing bolts to 25 N.m (18 Ib ft). 4. Install the exhaust crossover pipe. Refer to EXHAUST CROSSOVER PIPE REPLACEMENT (3.1L) or EXHAUST CROSSOVER PIPE REPLACEMENT (3.8L) . 5. Install the radiator inlet hose to the water outlet housing.

4T65E Transmission 1-2 Shift Shudder at Light to Moderate Acceleration (Replace Complete Second Clutch Assembly)

download
2001-2004 Buick Regal 2001-2005 Buick Century, LeSabre 2002-2007 Buick Rendezvous 2005-2007 Buick Terraza, LaCrosse, Allure (Canada Only) 2006-2007 Buick Lucerne 2001-2005 Chevrolet Venture 2001-2007 Chevrolet Impala, Monte Carlo 2005-2007 Chevrolet Uplander 2006-2007 Chevrolet Malibu SS, Malibu Maxx SS 2001-2002 Oldsmobile Intrigue 2001-2003 Oldsmobile Aurora 2001-2004 Oldsmobile Silhouette 2001-2005 Pontiac Aztek, Bonneville, Montana 2001-2007 Pontiac Grand Prix 2005-2007 Pontiac Montana SV6 2006-2007 Pontiac G6 GTP 2005-2007 Saturn Relay with 4T65E Automatic Transmission this service kit contains: Second Clutch Housing Fluid Seal Rings (613), a Second Clutch Assembly (617), a Case Cover (Channel Plate) Upper Gasket (430), and a Case Cover (Channel Plate) Lower Gasket (429). In addition to the content of this service kit, four other gaskets not included in this service kit will also be needed to complete the repair, a Control Valve Body Cover (Side Cover) Gasket (54), a Control Valve Body Cover (Side Cover) Inner Gasket (59), a Case Cover Lower Gasket (429), and a Case Cover Upper Gasket (430). These gaskets can be obtained by ordering service kit P/Ns 24206959 and 24206391. Be sure to use ONLY the Second Clutch Assembly and Second Clutch Housing Fluid Seal Rings provided in this service kit. DISCARD the Second Clutch Assembly and Second Clutch Housing Fluid Seal Rings removed from the transmission being serviced. Disassemble ONLY the Oil Pump Assembly from the Case Cover (Complete). DO NOT disassemble the Control Valve Body from the Case Cover. Remove ONLY the Case Cover-to- Case bolts to remove the Case Cover and Valve Body from Transmission Case AS AN ASSEMBLY . To access all Case Cover-to-Case bolts, it is necessary to remove the Pressure Control Solenoid Valve Assembly (322), and 1-2 & 3-4 Shift Solenoid Valve Assemblies (315A, 315B).

Low Engine Coolant Level Indicator Always On (Diagnose Low Coolant Level System Operation/Check Sensor for Oil Contamination)

download
2000-2002 Buick Century, Regal 2000-2001 Chevrolet Lumina 2000-2002 Chevrolet Impala, Monte Carlo 2000-2002 Pontiac Grand Prix 2000-2002 Oldsmobile Intrigue 1. Verify that the coolant is at proper level in the radiator and the coolant recovery bottle. If the coolant is low, add proper amount of 50/50 water and DEX-COOL® mixture. If the low coolant light operates properly, diagnose the cooling system for loss of coolant as outlined in SI. DO NOT proceed further with this bulletin. 2. Remove the low coolant level sensor. Refer to Coolant Level Module Replacement in the Engine Cooling sub-section. 3. With the key on, the engine off and the coolant level sensor disconnected from the vehicle wiring harness, observe the low coolant light: Subject: Low Engine Coolant Level Indicator Always On (Diagnose Low Coolant Level System Operation/Check Sensor for Oil Contamination) Models: 2000-2002 Buick Century, Regal 2000-2001 Chevrolet Lumina 2000-2002 Chevrolet Impala, Monte Carlo 2000-2002 Pontiac Grand Prix 2000-2002 Oldsmobile Intrigue • Light is on — Chassis wiring or instrument cluster concern. Follow the appropriate diagnostic information in SI. • 4. With the key off, connect the coolant level sensor into the vehicle’s wiring harness. Connect a ground wire (1) to the battery negative terminal. Using a sharp probe (3) attached to the ground wire, ground the coolant sensor probe (2) as shown in the illustration. Make sure a good contact is made. With the key on and the engine off, observe the low coolant light for at least 15 seconds. 5. Using a small wire brush or emery cloth, polish the low coolant level sensor probe to remove any film or oxidation. The probe should be a bright brass color when finished. Use Brake Parts Cleaner to flush removed deposits from the low coolant sensor probe. Reinstall the low coolant sensor into the vehicle and proceed to Step 6. 6. Flush the cooling system and install new DEX-COOL® mixture as outlined in the SI. Check the vehicle’s warranty history to determine if any engine gasket had recently been changed. If there has not been a recent gasket replacement, locate and repair the source of the engine oil contamination

1984-2002 Pontiac Camaro / Firebird ADJUSTABLE TORQUE ARM INSTALLATION MANUAL

download
Inspect the motor mounts and the transmission mount. Worn, weak or broken mounts will cause the torque arm to not function properly and can cause damage to your vehicle. Stock OE transmission mounts in Camaros and Firebirds are very weak and known to fail. If you have a broken or weak transmission mount, it will cause the torque arm to actually lift the tail end of the trans. up. This could cause severe wheel hop, driveline misalignment and possible damage to the transmission, drive shaft, u-joints, rear axle, torque arm, and/or floor pan of vehicle. We highly recommend using a good quality polyurethane transmission mount like Energy Suspension #33- 1108. Using the Energy Suspension transmission mount is good insurance that your transmission stay solid and the torque arm will work to its full potential. 2. Inspect the rear suspension bushings. We strongly recommend using either Edelbrock (#5274) lower trailing arms with a spherical ball on one end and polyurethane bushings on the other, Edelbrock (#5204) trailing arms with polyurethane bushings on both ends, or other high quality trailing arms that use high quality polyurethane bushings. We also recommend the use of an Edelbrock or other high quality panhard rod to replace the stock OE piece that uses sponge rubber bushings. The lower trailing arms and panhard rod secure the rear axle under the car. Upgrading to stronger high quality tubular trailing arms and panhard rod with polyurethane bushings will increase the overall strength, eliminate the sponge feel of rubber bushings and further increase the function potential of the torque arm. Worn out trailing arm or panhard rod bushings can contribute to or cause torque arm or other suspension component failures. Remember each suspension component

How to bypass the VATS (PASSKey II) system in a late model GM vehicle

download
Pontiac 1994-1996 Grand Prix 1992-1999 Bonneville 1993-2002 Firebird/Trans Am/Firehawk Buick 1994-1996 Regal 1992-1999 LeSabre 1991-1996 Park Avenue 1991-1996 Roadmaster Oldsmobile 1994-1997 Cutlass Supreme 1992-1999 Eighty Eight/LSS/Ninety Eight/Regency 1991-1996 Custom Cruiser Wagon Chevrolet 1995-1999 Monte Carlo 1995-2001 Lumina 1993-2002 Camaro 1986(?)-1996 Corvette (C4) Cadillac How to bypass the VATS system in a late model GM vehicle Bullet-Style” solderless connectors Heat Shrink Tubing Resistors of varying values (totalling the resistance measured across the key’s “pellet”) Alright, let’s begin the madness: 1. Take your DMM, set it to measure Ohms (use the 20k setting.) Measure the resistance across the pellet of the ignition key. Place one probe on the silver part of one side of the pellet, and the other probe on the other side. Write this value down. 2. Purchase a resistor or resistors that add up to the value measured in step 1. Radio Shack is a great place to go for the resistors, heat shrink tubing, and the “bullet-style” solderless connectors. 3. Take the 16 ga. wire and cut into 2 four-inch pieces. 4. Strip off approx 1/16″ of insulation off each side of both wire pieces. 5. Put your resistors together in series (or if you’re lucky and have a chip that has a resistance that matches a single resistor) and solder one wire to one end of the resistor(s) and the other wire to the other side. Example: You measure 11.72 on the 20k (k meaning kilo or 1,000) scale. The closest match is 11.801 which is a #15 “chip.” Always remember that resistors have a tolerance of 2%, meaning the resistance value of the “pellet” can be either 2% higher or 2% lower than 11.801 k ohms (11.72 falls in tolerance range.) You will want to aim for 11,801 ohms. So when you go to Radio Shack you want to pick up a 10,000 ohm (10k,) a 1,000 ohm (1k,) and an 800 ohm resistors to wire together in series to achieve the 11.801k ohm value.