Skip to content

toyota camry 2002 brake line diagram

You search PDF repair manual about toyota camry 2002 brake line diagram, if there are search results will appear below. If search results do not exist, please search by others keyword.

2004 Toyota Camry Disc Brake System Service/ Repair Manual

download
OVERHAUL HINT: Overhaul the RH side by the same procedures with LH side. REMOVE FRONT WHEEL 1. DRAIN BRAKE FLUID NOTICE: Wash off the brake fluid immediately if it comes into contact with a painted surface. 2. DISCONNECT FRONT FLEXIBLE HOSE 3. Remove the union bolt and a gasket from the disc brake cylinder, then disconnect the flexible hose from the disc brake cylinder. a. REMOVE DISC BRAKE CYLINDER ASSY FR LH 4. Remove the 2 bolts and disc brake cylinder. a. REMOVE DISC BRAKE PAD KIT FRONT (PAD ONLY) 5. Remove the 2 brake pads with anti-squeal shim. a. 6. Remove the 2 anti-squeal shims from each of 2 brake pads . a. Using a screwdriver, remove the wear indicator from each of 2 brake pads . b. REMOVE FRONT DISC BRAKE PAD SUPPORT PLATE 7. Remove the upper side front disc brake pad support plate. a. REMOVE FRONT DISC BRAKE PAD SUPPORT PLATE 8. Remove the bottom side front disc brake pad support plate. a. 10. Remove the cylinder slide bush from the cylinder slide pin. a. REMOVE FRONT DISC BRAKE BUSH DUST BOOT 11. Remove the 2 bush dust boots from the disc brake cylinder mounting. a. REMOVE FRONT DISC BRAKE CYLINDER MOUNTING LH 12. Remove the 2 bolts and disc brake cylinder mounting LH. a. 13. Using a screwdriver, remove the set ring and cylinder boot. a. REMOVE FRONT DISC BRAKE PISTON 14. Place a piece of cloth or similar, between the piston and the disc brake cylinder. a. Use compressed air to remove the piston from the disc brake cylinder. CAUTION: Do not place your fingers in front of the piston when using compressed air. NOTICE: Do not spatter the brake fluid . b. 2004 Toyota Camry L4-2.4L (2AZ-FE) REMOVE PISTON SEAL 15. Using a screwdriver, remove the piston seal from the disc brake cylinder. NOTICE: Do not damage the inner cylinder and the cylinder groove. a. REMOVE FRONT DISC BRAKE BLEEDER PLUG CAP 16. REMOVE FRONT DISC BRAKE BLEEDER PLUG 17. INSPECT BRAKE CYLINDER AND PISTON Check the cylinder bore and piston for rust and scoring 18.

Steering, Brake And Suspension Specialists Proportioning Valve Diagram

download
This diagram is the most common way to plumb a proportioning valve. In some cases, the right front line will be plugged off at the proportioning valve and the left front line will go to a “T” fitting. From the “T” fitting, the front lines then split off and go to the left and right wheels. Our proportioning valve has a warning light switch built in (this is not a stop light switch.) The warning light will detect any loss of pressure, for example, a leaky wheel cylinder. We recommend you wire this light into your system. Any two wire light socket will work. One wire goes to the accessory power and the other goes to the warning light. Our proportioning valves provide four functions: 1. Proportion pressure front and rear 2. 10 psi. residual check valve 3. Metering valve to apply pressure to the rear brakes before the front brakes 4. A brake warning light to detect a loss in pressure Proportioning Valve Plumbing Diagram: There are two proportioning valve lines that connect to the master cylinder provided in our kits. The first is a 90 degree bend with one leg longer than the other. This line must be oriented with the long leg connected into the front top hole of the proportioning valve and the short end in the front hole on the master cylinder. The second line has two 90 degree bends and has color coded fittings. The larger blue fitting goes into the back hole on the master cylinder and the smaller gold fitting goes into the back top hole on the proportion valve as shown in the diagram

TOYOTA Celica GT-S Front Big Brake Installation Instructions

download
Step 1 Jack up car Apply parking brake and properly block rear wheels. Break loose the lug nuts on both front wheels with a 21mm socket before jacking up the car. Make sure the jack and stand are supporting the frame rail portion of the body pan, not the flat floor pan. All Photographs Show Left Side Installation Jack Position Jack Stand Supporting Frame Rail Portion of Body Pan View of the stock left front brake assembly after wheel has been removed. NEVER LEAVE ANY VEHICLE SUPPORTED WITH ONLY A JACK, ALWAYS USE JACK STANDS. Step 2 Loosen the brake line fitting nut at the flex line using an 11mm wrench. A flare fitting wrench is preferable if available Using a pair of needle nose pliers, remove the stock clip from the hard line. Set clip aside, it will be used later when the new stainless steel lines are installed. Remove flex line fitting from standoff bracket and plug the hard line with one of the rubber plugs provided with the stainless steel line kit. This should effectively prevent fluid loss for the course of the installation. Step 3 Loosen the stock caliper mounting bolts with a 14mm wrench or socket. Remove the caliper with stock brake line attached. Be aware there may be some leakage from the open end of the brake line, but it should remain faily dry unless the pads / pistons on the caliper are retracted.

Toyota ISO Adapter Wiring Diagram

download
4R Runner 1991-2000 Amazon > 2000 Avensis > 1997 Avensis verso > 2003 Camry > 1991 Carina E > 1988 Celica > 1990 Corolla > 1988 Corolla verso > 2002 Hi-Ace > 1990 Hi-Lux > 1989 Land Cruiser 1984-2002 Lite Ace > 1993 MR2 > 1990 Paseo > 1997 Picnic > 1990 Previa > 1994 RAV-4 > 1994 Starlet 1993-1997 Supra 1986-1996 Tacoma 1995-2001 Yaris > 1999 Reference : AC000005AA If you are interested, contact our sales department : Car kit Parrot Battery Pin Number Couleur Description 1 White Mute In 1 2 Yellow Mute In 2 3 Blue Mute In 3 4 Orange + 12V Memory 5 Green 6 Brown 7 Red + 12 V Permanent 8 Black Masse Car kit Parrot, car’s speakers Pin Number Couleur Description 1 Grey Rear right speaker + 2 White Rear right speaker – 3 Blue Front right speaker + 4 Green Front right speaker – 5 Red Front left speaker + 6 Orange Front left speaker – 7 Bronw Rear left speaker + 8 Black Rear left speaker – Toyota Audio Toyota Supply N° Connector Color Description 2 Toyota 2 Green Rear left speaker + 2 Toyota 1 White Front left speaker + 1 Toyota 1 Grey Front Right speaker + 1 Toyota 2 Violet Rear Right speaker + 3 Toyota 2 Green Black Rear Left speaker – 9 Toyota 1 White Black Front Left speaker – 10 Toyota 1 Grey Black Front Right speaker- 6 Toyota 2 Black Violet Rear Right speaker – N° Connector Color Description 3 Toyota 1 Red +12 V Permanent 4 Toyota 1 Orange +12 Ignition 8 Toyota 1 Black Ground Toyota 1 Toyota 2 Toyota Audio Toyota Supply N° Connector Color Description 2 Toyota 4 Green Rear left speaker + 2 Toyota 3 White Front left speaker + 1 Toyota 3 Grey Front Right speaker + 1 Toyota 4 Violet Rear Right speaker + 3 Toyota 4 Green Black Rear Left speaker – 9 Toyota 3 White Black Front Left speaker – 10 Toyota 3 Grey Black Front Right speaker- 6 Toyota 4 Black Violet Rear Right speaker – N° Connector Color Description 3 Toyota 3 Red +12 V Permanent 4 Toyota 3 Orange +12 Ignition 8 Toyota 3 Black Ground

2002 Toyota Truck Tundra Access Cab SR5 2WD Timing Belt Service and Repair Manual

download
2002 Toyota Truck Tundra Access Cab SR5 2WD V6-3.4L (5VZ-FE) Copyright © 2008, ALLDATA 9.50 Page 2 REMOVAL 1. REMOVE ENGINE UNDER COVER 2. DRAIN ENGINE COOLANT 3. DISCONNECT UPPER RADIATOR HOSE 4. DISCONNECT PS PUMP FROM ENGINE a. Disconnect the 2 PS air hoses from the air intake chamber and resonator. b. Remove the bolt holding the PS pressure tube clamp to the frame. c. Remove the drive belt. d. Remove the bolt and nut, and disconnect the PS pump from the engine. 5. w/ A/C: DISCONNECT A/C COMPRESSOR FROM ENGINE a. Disconnect the A/C compressor connector. b. Remove the drive belt. c. Remove the 4 bolts, and disconnect the A/C compressor from the engine. 6. LOOSEN FAN WITH FLUID COUPLING AND FAN PULLEYS 7. REMOVE DRIVE BELT FOR GENERATOR 8. REMOVE NO.2 FAN SHROUD 9. REMOVE FAN WITH FLUID COUPLING AND FAN PULLEYS 10. w/ A/C: REMOVE A/C COMPRESSOR BRACKET Remove the 5 bolts and A/C compressor bracket. 11. DISCONNECT UPPER RADIATOR HOSE 12. REMOVE NO.2 TIMING BELT COVER a. Disconnect the camshaft position sensor connector from the No. 2 timing belt cover. b. Disconnect the 4 high-tension cord clamps from the No. 2 timing belt cover. c. Remove the 6 bolts and timing belt cover. 13. REMOVE FAN BRACKET a. Remove the nut and PS pump adjusting strut. b. Remove the bolt, nut and fan bracket. 14. SET NO. 1 CYLINDER AT TDC/COMPRESSION a. Turn the crankshaft pulley and align its groove with timing mark “0″ of the No. 1 timing belt cover. b. Check that the timing marks of the camshaft timing pulleys and No. 3 timing belt cover are aligned. If not, turn the crankshaft pulley 1 revolution (360°) . HINT: When re-using timing belt: Place the matchmarks on the timing belt and camshaft timing pulleys, and place matchmark on timing belt to match the end of the No. 1 timing belt cover. 15. REMOVE TIMING BELT TENSIONER Alternately loosen the 2 bolts, and remove them, the belt tensioner and dust boot. 16. REMOVE TIMING BELT