Skip to content

toyota engine 1kd

You search PDF repair manual about toyota engine 1kd, if there are search results will appear below. If search results do not exist, please search by others keyword.

2005 TOYOTA AVALON TVIP V4 (REMOTE ENGINE STARTER) INSTALLATION MANUAL

download
TOYOTA AVALON 2005 – TVIP V4 (REMOTE ENGINE STARTER) Procedure Page 2 of 33 pages Issue: C 02/02/05 Care must be taken when installing this accessory to ensure damage does not occur to the vehicle. The installation of this accessory should follow approved guidelines to ensure a quality installation. These guidelines can be found in the “Accessory Installation Practices” document. This document covers such items as:- • Vehicle Protection (use of covers and blankets, cleaning chemicals, etc.). • Safety (eye protection, rechecking torque procedure, etc.). • Vehicle Disassembly/Reassembly (panel removal, part storage, etc.). • Electrical Component Visassembly/Reassembly (battery disconnection, connector removal, etc.). Please see your Toyota dealer for a copy of this document. 1. Vehicle Disassembly. (a) Remove the negative battery cable. (Fig. 1-1) (1) Protect the fender before starting. (2) Do not touch the positive terminal with any tool removing the cable. (b) Remove the glove box under-dash cover. (Fig. 1-2) (c) Remove the passenger’s step cover. (Fig. 1-3) Fig. 1-1 10mm Wrench Negative Battery Cable Battery Step Cover Fig. 1-3 Nylon Panel Removal Tool Fig. 1-2 Under-Dash Cover Nylon Panel Removal Tool TOYOTA AVALON 2005 – TVIP V4 (REMOTE ENGINE STARTER) Procedure Page 3 of 33 pages Issue: C 02/02/05 (d) Remove the passenger’s cowl cover. (Fig. 1-4) (1) Remove one nut securing the cowl cover. (e) Remove one screw and one bolt from the glove box assembly. (Fig. 1-5) (f) Remove the glove box assembly. (Fig. 1-6) (1) Open the glove box door and remove three screws securing the glove box assembly. (2) Disconnect the trunk opener cancel switch from the glove box assembly if equipped. For vehicles with Smart Entry, the disassembly process ends on Step f. Go to Section 5. For vehicles without Smart Entry, continue the disassembly process. FOR VEHICLES WITHOUT SMART ENTRY SYSTEM ONLY. (Step g) NOTE: Do not perform this step if the vehicle has Smart Entry. (g) Remove the driver’s step cover. (Fig. 1-7) Screw Fig. 1-5 10mm Wrench, Phillips Screwdriver Bolt Glove Box Assembly Cowl Cover Fig. 1-4 Nut Fig. 1-6 Nylon Panel Removal Tool, Phillips Screwdriver Screws (x3) Glove Box Assembly Trunk Opener Cancel Switch Connector Fig. 1-7 Step Cover Nylon Panel Removal Tool
TOYOTA AVALON 2005 – TVIP V4 (REMOTE ENGINE STARTER) Procedure Page 4 of 33 pages Issue: C 02/02/05 FOR VEHICLES WITHOUT SMART ENTRY SYSTEM ONLY. (Steps h-l) NOTE: Do not perform this step if the vehicle has Smart Entry. (h) Remove the driver’s cowl cover. (Fig. 1-8) (1) Remove the one nut securing the cowl cover. (i) Remove the hood release cable. (Fig. 1-9) (1) Do not bend the hood release cable. (j) Open the screw cover on the lower dash cover. Insert the tip of a Nylon Panel Removal Tool in the upper slot to loosen it. (Fig. 1-9) (1) Remove one screw and one bolt securing the lower dash cover. (k) Remove the lower dash cover. (Fig. 1-10) (1) Disconnect the temperature sensor (connector and aspirator hose) from the lower dash cover if equipped. (l) Carefully remove the driver side airbag assembly. (Fig. 1-11) (1) Remove four bolts securing the driver side airbag assembly. (2) Be careful not to get cut by the sharp metal edges. (3) Do not disconnect the airbag assembly. (4) Use the empty V4 kit box to support the airbag assembly on the floor

1992 Toyota Truck Pickup 2WD Cooling and Exhaust Engine Ignition Timing Adjustments Manual

download
1. Connect a tachometer test probe to terminal IG of the check connector, Fig. 211 2. NOTE: Never let the tachometer lead touch ground as this could cause damage to the igniter and/or coil. Be sure to check that your tachometer is compatible with this ignition system. Consult the operating manual for your instrument. Service Check Connector 3. Fig. 223 Ignition Timing (10) Check idle speed . 4. Idle Speed : 800 rpm Using a timing light, verify that the timing mark on the timing cover is aligned with the mark on the crankshaft pulley, Fig. 223 5. Ignition Timing: 10°BTDC at idle Tighten the distributor bolt and recheck the ignition timing. 6. Remove service wire. 7. Check idle advance timing with service wire removed. 8. Ignition Timing: 8°BTDC at idle Check idle speed and adjust if necessary, COMPUTERIZED ENGINE CONTROLS. 9. Disconnect tachometer and timing light from engine. 10. Timing Belt Removal Notes Fan Shroud Removal & Installation Remove radiator fan upper and lower shrouds. 1. Installing Power Steering Pump And Belt Remove power steering pump drive belt and pump. 2. Disconnect No. 2 and No. 3 air hoses from air pipe. 3. 4. Fan Removal Remove alternator drive belt , cooling fan, belt guide and fan pulley. 5. Remove No. 2 timing belt cover. 6. Fig. 6 Aligning Timing Marks Place No. 1 cylinder at TDC of compression stroke by turning the crankshaft pulley and aligning pulley groove with the “0” mark on the No. 1 timing belt cover. Ensure alignment marks on the camshaft timing sprockets and the No. 3 timing belt cover are correctly aligned, Fig. 6. 7. If not, turn the crankshaft pulley one complete revolution. 8. Crankshaft Pulley Removal

1994 Toyota Paseo ENGINE IDENTIFICATION/ VALVE CLEARANCE ADJUSTMENT

download
1) Disconnect PCV hose, necessary electrical connections and spark plug wires to access valve cover. Remove nuts, seal washers, valve cover and gasket. 2) Rotate crankshaft clockwise so cylinder No. 1 is at TDC on compression stroke. Cylinder No. 1 is front cylinder at timing belt end of engine. Ensure timing mark on crankshaft pulley aligns with “0″ mark on timing belt cover. 3) Ensure valve lifters on cylinder No. 1 are loose and valve lifters on cylinder No. 4 are tight. If conditions are not as described, rotate crankshaft clockwise one complete revolution (360 degrees). 4) Using feeler gauge, measure valve clearance between valve lifter and camshaft on intake valves of cylinders No. 1 and 2, and exhaust valves of cylinders No. 1 and 3. Record valve clearance. Rotate crankshaft clockwise one complete revolution (360 degrees). 5) Measure and record valve clearance on intake valves of cylinders No. 3 and 4, and exhaust valves of cylinders No. 2 and 4. Ensure valve clearance is within specification. See VALVE CLEARANCE SPECIFICATIONS table. VALVE CLEARANCE SPECIFICATIONS TABLE (1) Application In. (mm) Exhaust Valve ………….. .012-.016 (.31-.41) Intake Valve …………… .006-.010 (.15-.25) (1) – Adjust valve clearance with engine cold. 6) If valve clearance requires adjustment, rotate camshaft so lobe on valve to be adjusted is facing upward, away from valve lifter. Position notch area on valve lifter toward inside of cylinder head. DO NOT align notch area with camshaft. Use Valve Clearance Adjuster (SST 09248-55040) to adjust valve clearance. 7) Using SST “A” of valve clearance adjuster, push downward on valve lifter. Place SST “B” between camshaft and valve lifter. See Fig. 2. Ensure enough clearance exists for adjusting shim removal. Remove SST “A”. Fig. 2: Adjusting Valve Clearance Courtesy of Toyota Motor Sales, U.S.A., Inc. 8) Using small screwdriver and magnet, remove adjusting shim. Measure and record thickness of removed shim. Using measured clearance and adjusting shim thickness, select proper replacement adjusting shim. See Figs. 4 and 5. 9) Install replacement adjusting shim. Recheck valve clearance. Apply sealant at indicated valve cover sealing areas on cylinder head. See Fig. 3. 10) Using NEW gasket, install valve cover and sealing washers. Install and tighten nuts to specification. See TORQUE SPECIFICATIONS. To install remaining components, reverse removal procedure. NEW SHIM THICKNESS TAB

TOYOTA TO CHEVY AND BUICK ENGINE – TURBO CHARGED INSTALLATION INSTRUCTIONS

download
INSTALLATION INSTRUCTIONS: 1. Install the pilot bushing into the engine crank. 2. Bolt the flywheel to the engine crank using special flywheel bolts. 3. Assemble the clutch assembly and special disc to the flywheel using special clutch bolts. 4. Assemble the clutch release arm to the inside ball pivot of the bellhousing. 5. Bolt the slave cylinder to the outside of the bellhousing. 6. Test fit the bellhousing assembly over the clutch assembly and onto the engine block. 7. Place the N1430 release bearing onto the clutch arm fork. 8. Adjust the length of the slave cylinder push rod to a length that provides a minimum of 1/8″ clearance between the release bearing face and clutch fingers. 9. This test fit over the clutch assembly is primarily done for establishing the push rod length. If this procedure is eliminated, you will not have any visual inspection for verifying the push rod adjustment. 10. Remove the bellhousing assembly from the engine. 11. Bolt the bellhousing to the front of your Toyota 5 speed transmission using the original bolts. Make sure that the two dowel pins installed in the face of the 5 speed transmission are properly fitted to the Advance Adapter bellhousing. 12. Slide the new release bearing onto the Toyota bearing retainer. Make sure that there is grease in the internal cavity of the release bearing. Most new bearings are pre-lubricated. 13. With all the components in position, you can now bolt the new bellhousing assembly onto the engine block. We have provided six (6) new socket head bolts, 3/8″-16 x 1-1/2″ long for this purpose. Make sure the engine dowel pins are properly aligned with the new bellhousing dowel pin holes. DO NOT FORCE THE BELLHOUSING ONTO THE ENGINE BLOCK. Some applications may require the tip of the input shaft to be modified slightly. The bellhousing must fit evenly to the engine block. 14. With the bellhousing now in position and the slave cylinder push rod installed, you should be able to verify the clearance between the release bearing & clutch fingers. The lever should have movement of approximately 1/8″ to 1/4″. CAUTION : If you have too much clearance, you will be utilizing too much of the slave cylinder stroke and could possibly prevent you from obtaining a full clutch release. A light duty return spring attached to the clutch release arm will prevent any premature contact of the release bearing with the clutch fingers. 15. The Toyota Land Cruiser slave cylinder will replace the original Toyota slave cylinder. The Toyota truck hydraulic slave cylinder line will have exactly the same fitting size as used on the Land Cruiser slave cylinder. 16. With the new slave cylinder installed, you can now bleed the slave cylinder installation by pumping up the slave cylinder pedal. Most installations are compatible with the original Toyota master cylinder. We have encountered a few installations that require changing of the Toyota master cylinder to a smaller 3/4″ piston. If you have any type of clutch difficulty related to full disengagement of the clutch assembly, contact Advance Adapters for any updated information.

2002 Toyota Truck Tundra Access Cab SR5 2WD Timing Belt Service and Repair Manual

download
2002 Toyota Truck Tundra Access Cab SR5 2WD V6-3.4L (5VZ-FE) Copyright © 2008, ALLDATA 9.50 Page 2 REMOVAL 1. REMOVE ENGINE UNDER COVER 2. DRAIN ENGINE COOLANT 3. DISCONNECT UPPER RADIATOR HOSE 4. DISCONNECT PS PUMP FROM ENGINE a. Disconnect the 2 PS air hoses from the air intake chamber and resonator. b. Remove the bolt holding the PS pressure tube clamp to the frame. c. Remove the drive belt. d. Remove the bolt and nut, and disconnect the PS pump from the engine. 5. w/ A/C: DISCONNECT A/C COMPRESSOR FROM ENGINE a. Disconnect the A/C compressor connector. b. Remove the drive belt. c. Remove the 4 bolts, and disconnect the A/C compressor from the engine. 6. LOOSEN FAN WITH FLUID COUPLING AND FAN PULLEYS 7. REMOVE DRIVE BELT FOR GENERATOR 8. REMOVE NO.2 FAN SHROUD 9. REMOVE FAN WITH FLUID COUPLING AND FAN PULLEYS 10. w/ A/C: REMOVE A/C COMPRESSOR BRACKET Remove the 5 bolts and A/C compressor bracket. 11. DISCONNECT UPPER RADIATOR HOSE 12. REMOVE NO.2 TIMING BELT COVER a. Disconnect the camshaft position sensor connector from the No. 2 timing belt cover. b. Disconnect the 4 high-tension cord clamps from the No. 2 timing belt cover. c. Remove the 6 bolts and timing belt cover. 13. REMOVE FAN BRACKET a. Remove the nut and PS pump adjusting strut. b. Remove the bolt, nut and fan bracket. 14. SET NO. 1 CYLINDER AT TDC/COMPRESSION a. Turn the crankshaft pulley and align its groove with timing mark “0″ of the No. 1 timing belt cover. b. Check that the timing marks of the camshaft timing pulleys and No. 3 timing belt cover are aligned. If not, turn the crankshaft pulley 1 revolution (360°) . HINT: When re-using timing belt: Place the matchmarks on the timing belt and camshaft timing pulleys, and place matchmark on timing belt to match the end of the No. 1 timing belt cover. 15. REMOVE TIMING BELT TENSIONER Alternately loosen the 2 bolts, and remove them, the belt tensioner and dust boot. 16. REMOVE TIMING BELT