Skip to content

toyota sienna 2011 wiring diagram

You search PDF repair manual about toyota sienna 2011 wiring diagram, if there are search results will appear below. If search results do not exist, please search by others keyword.

1992 Toyota Cressida Wiring Diagram

download
tem Wire ColorPolarity Wire Location 12V white – white/red Positive (+) steering column Starter black/white Positive (+) steering column Starter 2 none Ignition black/yellow Positive (+) steering column 2nd Ignition black/red Positive (+) steering column 3rd Ignition none Accessory blue/red Positive (+) steering column Accessory 2 none Tachometer black/yellow check conn(ig-) Power Door (Lock) Wiring Diagram for [ Negative (-) ] Door Lock green/red Negative (-) pass kick or theft ecu Power Door (Unlock) Wiring Diagram for [ Negative (-) ] Door Unlock green/whiteNegative (-) pass kick or theft ecu Door Trigger red/white Negative (-) theft ecu[1] Dome Supervision Wiring Diagram for [ none ] Dome none none none Headlights red/yellow Negative (-) steering column Parklight Positive green Positive (+) dimmer controll or dkp Parklight Negative green/whiteNegative (-) steering column Wipers blue/black Positive (+) steering column Left Front Window (Up/Down) grn/wht – red/blu in drivers door Right Front Window (Up/Down) pnk/blk – pnk in drivers door or dkp Left Rear Window (Up/Down) red – red-yel A in drivers door or dkp Right Rear Window (Up/Down) grn/blk – red/blk A in drivers door or dkp Trunk/Hatch Pin red/white Negative (-) at light, or theft ecu Hood Pin tied with doors Trunk/Hatch Release Wiring Diagram for [] Trunk/Hatch none Factory Alarm (Arm) arms with lock Factory Alarm (Disarm) disarms with unlock Horn white/red Negative (-) st.column or theft ecu Brake green/black Positive (+) brake switch Door Motor (Lock) none none none Door Motor (Unlock) none none none

2004 – 2006 Toyota Sienna Vehicles Equipped w/ Power Back Door (Power Rear Liftgate) Repair Manual

download
Certain 2004 – 2006 Model Year Sienna vehicles equipped w/Power Back Door (Rear Liftgate) Q1: What is the condition? A1: Toyota has determined that the gas struts used to help lift and support the Power Rear Liftgate in certain 2004 through 2006 model year Sienna vehicles could be wearing out sooner than expected. As the gas struts deteriorate, the performance of the Power Rear Liftgate will begin to degrade, and the Power Rear Liftgate will operate more slowly than when the gas struts were new. Only Sienna vehicles equipped with the Power Rear Liftgate are involved. Q2: Are there any warnings that this condition exists? A2: Owners may notice that the Power Rear Liftgate will not remain in the open position. If not repaired, the gas struts may not be able to support the weight of the liftgate when it is open, and eventually, the gas struts could deteriorate to the point that the liftgate will fall about ten inches after it reaches the fully open position, at which point the power motor will engage and power the liftgate to the fully closed position. This condition may cause injury to a person who is struck by the liftgate when it falls or when it is closing. Q3: When were these vehicles produced, and how many vehicles are involved? A3: Only certain 2004 through 2006 model year Sienna vehicles equipped with the Power Rear Liftgate, produced between January 2003 and December, 2006 are involved. Approximately 196,000 vehicles are involved nationwide.

TOYOTA SIENNA SEAT REMOVAL AND INSTALLATION MANUAL

download
Front Seat Installation Instructions 1. Roll seat base into position, just behind the floor mounted strikers. Pull up the release handle. 2. Lift the rear of the seat base up (a) and slide it forward (b) to engage the front strikers. 3. Push down on rear of seat to engage rear strikers. Push down the release handle to lock the seat base into place. 4. Connect (plug) seat electrical harness to B-pillar receptacles. See pages 36 and 37 for details. Position seat and pull release handle up. 1 2 3 Lift up (a) and slide forward (b) to engage front strikers. Push down to engage rear strikers. Push down handle to lock into place

1984 TOYOTA SIENNA 2nd SEAT FLOOR LINER INSTALLATION MANUAL

download
TO INSTALL YOUR LINER, FIRST SLIDE THE 2ND ROW SEATS TOWARD THE BACK OF THE VEHICLE FAR ENOUGH TO ALLOW ROOM FOR THE LINER TO BE INSTALLED. WITH THE LINER IN PLACE, MOVE THE 2ND ROW SEATS FORWARD UNTIL THEY MATCH UP TO THE REAR EDGE OF THE LINER. YOUR SIENNA LINER IS DESIGNED TO WORK WITH THE MULTIPLE CONFIGURATIONS OF THE SIENNA VAN. AS IT IS BOXED, THE LINER WILL FIT 7- PASSENGER MODELS WITH THE FRONT ROW CONSOLE POSITIONED BETWEEN THE FRONT ROW OF SEATS. THE LINER CAN EASILY BE TRIMMED TO ALLOW THE CONSOLE TO BE REPOSTIONED INTO THE 2ND ROW AREA AS SHOWN IN THE DIAGRAM ABOVE (SEE AREA 1 AND PHOTOS ON BACK OF THIS PAGE). TO TRIM, SIMPLY USE THE MOLDED IN STEP IN THE PART AS A GUIDE AND REMOVE THE SECTION OF THE LINER AS SHOWN. A UTILITY KNIFE OR HEAVY SHEARS WORK WELL FOR TRIMMING. IF YOUR SIENNA IS AN 8-PASSENGER MODEL, YOU WILL NEED TO REMOVE THE “TONGUE” FROM THE REAR OF THE LINER (SEE AREA 2 ABOVE). THIS IS EASILY DONE USING THE MOLDED IN STEP IN THE PART AS THE TRIMMING GUIDE. ONCE AGAIN, A UTILITY KNIFE OR HEAVY SHEARS WORK WELL FOR TRIMMING.

Wiring Toyota Switch to SH-R-00 Carbon Fiber Seat Heater

download
Wiring Toyota Switch to SH-R-00 Carbon Fiber Seat Heater (Switch is ready to use with FWSH-U-00 FlexWire Seat Heater) SH-R-EXT (rev 0) Harness plug: Black, White, Red, Green Toyota Switch Pigtail CarbonFiber Harness Extn To use the Toyota Switch with SH-R-00 Carbon Fiber Seat Heater kit, you will need to direct connect the wires, eliminating the modular plugs on both the harness extension and switch. 1. Cut the plug end off the Toyota switch pigtail harness. 2. Cut the end plug off the wire harness extension. 3. Attach spade connectors to each wire. 4. Cross connect the wires as shown. 5. Test switch before mounting