toyota sienna bumper fasteners

You search PDF repair manual about toyota sienna bumper fasteners, if there are search results will appear below. If search results do not exist, please search by others keyword.



  toyota sienna bumper fasteners Direct Download speed 5432 Kb/s

  toyota sienna bumper fasteners Full Version speed 8172 Kb/s



TOYOTA FJ CRUISER – FRONT BUMPER INSTALLATION INSTRUCTIONS

0

Filed Under (Toyota Manuals) by admin on 05-02-2011

download
Front Bumper Installation – TOYOTA FJ CRUISER Step 1 Very Important Before beginning installation, assure that vehicle has been pulled forward into work-area with the wheels straight and that the ground is level. The clearances around the FJ bumper are critical to proper installation and fitment. Moving vehicle with wheels turned causes slight frame twist preventing ease of removal of OE bumper and installation of new bumper without issue. Make sure you have plenty of room to work around front of vehicle. Open the hood at this time, you will need to see down through the inner-body core-support while removing your OE bumper and installing your Body Armor FJ Bumper. Step 2 a. Unpack bumper using staple puller to remove staples. Save all packing materials and take care not to tear cartons. b. Remove hardware and misc.parts. Check parts/hardware list to confirm all parts and necessary hardware are included. c. It’s a good idea to spray all OE attaching hardware at this time with penetrating oil before beginning removal of OE bumper. This will ease removal as well as to help assure that none of the bolts’ / nuts’ threads are damaged during removal. Use extra caution when working with the bumper mounting studs & nuts. Step 3Prep bumper for install: You may install your auxilary lights in the light pockets. The light tab is slotted to allow for adjustment for adjustment for light grilles. You may also attach a second set of lights on the top deck . Also attach the grill guard at this time. Step 4 a. Begin removing OE bumper following instructions and photos on the following page for detailed descriptions and references. When done, proceed to Step 4 here. Step 5 a. If equipped, remove OE chassis skid plate and set aside for install after new bumper is installed. Save OE hardware to re-install the skid plate once new bumper is installed (3 upper bolts and 2 lower bolts, lowers have spacers between frame & skid plate). b. Remove the (3) outer hold-down hex nuts holding bumper to frame-caps on both passenger and driver sides. Un-clip the outer ends of the bumper from the outer bumper support clips (see Photo 5 on following page) by pulling bumper fascia down and out of clip on driver and passenger sides. Next, while a helper holds the bumper in place, loosen and remove the inner hold-down hex nuts on both passenger and driver sides. Reference Photo 1 on the last page for stud locations. The bumper should now slide off the front of the locating / mounting studs in the frame-caps. Remove slowly prevent paint damage. Save hold-down nuts. c. Remove the outer bumper support clips from both driver and passenger sides (see Photo 5 on following page) Step 6 a. If you bought a winch, skip to Step 6b. If you did not purchase a winch, you can mount the winch cover plate / lower bumper fascia, and fairlead slot cover plate to the bumper now, using (6) 3/8″ x 1″ bolts with (2) flat washers, (1) lock washer, and (1) hex nut on each bolt. See photos 4 & 5 on the last page for reference. b. If you purchased a winch for your FJ, now is the time to mount it in the bumper. The winch will bolt down using the fairlead mounting bracket and 10mm bolts to secure winch & fairlead bracket to bumper. The roller fairlead bolts to the fairlead bracket using the 1/2″ hex nuts supplied. See photo 3 on the last page for reference. Be sure to mount with the correct side of winch to passenger side for solenoid pack installation / clearance. Once the winch is bolted in, you can mount the winch cover plate / lower bumper fascia to the bottom of the bumper using (4) of the 3/8″ x 1″ bolts with (2) flat washers, (1) lock washer and (1) hex nut on each bolt. If you purchased lights, mount them to the light tabs. It the lights have a protective grille you should be able. to use the cover. Important: Follow winch mfr’s directions for cable to winch / solenoid / battery connections. Use caution to assure clearance of any and all bumper / winch / mounting surfaces at all cable end connections. Coil cables and lay in winch mount plate to protect against damage while installing bumper onto vehicle. Place coiled cables in winch mount plate to assure no interference with the radiator, a/c line and / or inner body core support during bumper installation. Cables to be run in Step 7. Step 7 Along with your helper, one person on each side, guide your Body Armor FJ Bumper onto the the frame-cap mounting studs. Use caution guiding the bumper on slowly and evenly to prevent paint damage. Locating / mounting studs and bumper mounting plates can be seen down through inner-body core support while guiding bumper into place. Make sure the bumper does not contact grill or fascia while installing bumper as this can cause paint damage. While you or your helper hold the bumper in place, thread the OE hold-down nuts onto mounting studs to hold the bumper in place, hand tighten at this time. Step 8 Confirm bumper is even side-to-side, torque hold-down nuts to 80 ft.lbs. Again confirm bumper is even and there are no clearance issues between the bumper and any part of the body and / or inner-body core-support. You can now run the winch cables through the inner-body core support to the battery. If you purchased a set of lights to be used with your bumper, you can now wire them up, please follow the detailed light manufacturer instructions. **Body Armor is not responsible for any issues with respect to the wiring, operation or warranties to the lights Step 9 a. Fit the wheel well inner-liner end-caps to the bottom of the bumper at each corner and bolt up with supplied 1/4″ x .75″ phillips- head machine screws, (2) each side, into drilled / threaded holes in bottom corners of bumper. See photos 6 & 7 on the last page. b. Next, using the OE hardware and spacers, re-install your chassis skidplate, making sure it’s straight before tightening. c. Using the (2) remaining 1/4″ x .75″ phillips-head machine screws, mount your license plate to threaded holes in the bumper face. d. Re-install the grill by snapping onto clips and using the OE push-pins and screws to hold down in OE locations. ** trimming off the front inner fender is a customer option, it is not required. We recommend you check the torque of all bolts after about two weeks, and after every off-road / trail run thereafter to assure tightness

Related Content:

how to remove chevy sonic front bumper, INSTALLING A FRONT BUMPER ON THE TOYOTA RAV 4, replacing front bumper end cap on 2012 Toyota FJ cruiser, 2004fordf150frontbumperdiagram, 2000 4runner step bumper rear chrome install instructions, remove back bumper on kia sedona, remove 2006 toyota matrix rear bumper, remove back bumper on kia sedona cover, rear fender for 2008 camry, prius steering wheel pad removal instructions

2007 TOYOTA FJ CRUISER HEAVY DUTY WINCH BUMPER INSTALLATION INSTRUCTIONS

0

Filed Under (Toyota Manuals) by admin on 05-04-2012

download
INSTALLATION 1. Remove the screws from the rear corners of the bumper, two in each side. Figure 2 Figure 2 Bumper mounting screws, left side 2. Remove the eight screws along the bottom of the bumper. Figure 3 Figure 3 Lower bumper mounting screws Remove 2 screws in rear of bumper Remove 8 screws in bottom of bumper (4 per side) WARN INDUSTRIES PAGE 4 73465 A0 3. Lift the hood and remove the two screws from the top of the grille. Retain the hardware for use later. Figure 4 Figure 4 Grille fasteners 4. Remove the two plastic fasteners from the top of the grille. Retain the hardware for use later. Carefully pry the center pins up before removing the fasteners. Figure 5 Figure 5 Left grille fastener removal 5. Pull the grille free of the retaining clips with a “sharp” pull. Remove 2 screws Remove 2 plastic fasteners (1each side) Lift center pin then pry fastener out WARN INDUSTRIES PAGE 5 73465 A0 6. Remove five plastic fasteners from the top of the bumper. Two are behind the upper bumper support. Figure 6 Figure 6 Bumper fasteners 7. Pull the bumper corners free by pulling the ends rearward and out. The top of the bumper is snapped into plastic clips just below the fender corners, in front of the flares. Pull the bumper free. Figure 7 Figure 7 Left bumper end removal Remove 5 plastic fasteners (2 behind bumper not shown) WARN INDUSTRIES PAGE 6 73465 A0 8. Remove the two screws that hold each plastic mounting block in place and remove the blocks. Figure 8 Figure 8 LH bumper mounting block 9. Remove the three screws and remove the upper bumper support. Figure 9 Figure 9 Upper bumper support Remove 2 screws and remove plastic block Remove 3 screws Do not remove the nuts on top Bumper mounting block Upper bumper support WARN INDUSTRIES PAGE 7 73465 A0 10. Remove the 8 hex flange nuts and remove the bumper beam. Retain the hardware for bumper installation. Figure 10 Figure 10 Bumper beam, left side shown 11. Remove the four screws and remove the skid pan. Retain the hardware for reinstallation of the skid pan. Figure 11 Figure 11 Skid pan 12. Remove the molded plastic inner fender extensions by clipping or drilling out the rivets holding them to the bottom of the inner fenders. Figure 12 Remove 4 fasteners to remove skid pan Remove 4 flange nuts per side Bumper beam WARN INDUSTRIES PAGE 8 73465 A0 Figure 12 Left side fender extension 12. Locate the 1″ hole in the side of the frame behind the body mount. Drill a 1/2″ hole through the center into the inner wall. The Spacer Tube may be used as a centering tool. Repeat for opposite side. Figure 13 Figure 13 Outside left frame rail 13. Hold the Lower Frame Bracket in position and insert a 12mm bolt with 1/2″ lock washer and flat washer through the bottom hole in the Bracket and into the threaded hole in the frame. Do not tighten yet. Figure 14 Drill ½” hole through center of existing hole into inner frame wall Clip or drill rivets to remove fender extension Fender extension WARN INDUSTRIES PAGE 9 73465 A0 14. Slide a 1/2″ flat washer and Spacer Tube over a 1/2 x 4″ bolt and insert through the Lower Frame Bracket and Frame. Install 1/2″ lock washer and hex nut. Do not tighten yet. Figure 14 15. Slide an Upper Frame Bracket above the frame rail along the inside of the Lower Frame Bracket. Align the holes and insert two 7/16 x 1 1/2″ bolts through the holes and install a lock washer and hex nut on each. Do not tighten yet.

Related Content:

how to remove 03 sequoia rere bumper, fj cruiser front bumper removal, romoving rear bumper on mazda 6, removed 2012 mazda 3 bumper, remove rear bumper 2005 camry, remove lower bumper r350, removal of rear bumper 2003 ford explorer, removal of fj cruiser lower grill, rear bumper of 07 corolla removal, plasitic piece under carraige nissal altima

Toyota ISO Adapter Wiring Diagram

0

Filed Under (Toyota Manuals) by admin on 19-05-2011

download
4R Runner 1991-2000 Amazon > 2000 Avensis > 1997 Avensis verso > 2003 Camry > 1991 Carina E > 1988 Celica > 1990 Corolla > 1988 Corolla verso > 2002 Hi-Ace > 1990 Hi-Lux > 1989 Land Cruiser 1984-2002 Lite Ace > 1993 MR2 > 1990 Paseo > 1997 Picnic > 1990 Previa > 1994 RAV-4 > 1994 Starlet 1993-1997 Supra 1986-1996 Tacoma 1995-2001 Yaris > 1999 Reference : AC000005AA If you are interested, contact our sales department : Car kit Parrot Battery Pin Number Couleur Description 1 White Mute In 1 2 Yellow Mute In 2 3 Blue Mute In 3 4 Orange + 12V Memory 5 Green 6 Brown 7 Red + 12 V Permanent 8 Black Masse Car kit Parrot, car’s speakers Pin Number Couleur Description 1 Grey Rear right speaker + 2 White Rear right speaker – 3 Blue Front right speaker + 4 Green Front right speaker – 5 Red Front left speaker + 6 Orange Front left speaker – 7 Bronw Rear left speaker + 8 Black Rear left speaker – Toyota Audio Toyota Supply N° Connector Color Description 2 Toyota 2 Green Rear left speaker + 2 Toyota 1 White Front left speaker + 1 Toyota 1 Grey Front Right speaker + 1 Toyota 2 Violet Rear Right speaker + 3 Toyota 2 Green Black Rear Left speaker – 9 Toyota 1 White Black Front Left speaker – 10 Toyota 1 Grey Black Front Right speaker- 6 Toyota 2 Black Violet Rear Right speaker – N° Connector Color Description 3 Toyota 1 Red +12 V Permanent 4 Toyota 1 Orange +12 Ignition 8 Toyota 1 Black Ground Toyota 1 Toyota 2 Toyota Audio Toyota Supply N° Connector Color Description 2 Toyota 4 Green Rear left speaker + 2 Toyota 3 White Front left speaker + 1 Toyota 3 Grey Front Right speaker + 1 Toyota 4 Violet Rear Right speaker + 3 Toyota 4 Green Black Rear Left speaker – 9 Toyota 3 White Black Front Left speaker – 10 Toyota 3 Grey Black Front Right speaker- 6 Toyota 4 Black Violet Rear Right speaker – N° Connector Color Description 3 Toyota 3 Red +12 V Permanent 4 Toyota 3 Orange +12 Ignition 8 Toyota 3 Black Ground

Related Content:

2002 toytoa camry tank vent valve, toyota 4af engine repair manual, 1998 toyota A245E automatic transmission rebuild manual, 2002 toyota tundra 4 wheel drive suspencion, 2004 toyota highlander window diagram, 2009sienna v6 thermostadt extraction, diagram of front passenger seat occupant sensors and where 2005 toyota camry located, show prado 1999 valve attached to rear brake pipe with spring, 4k toyota carburator manual, po500 toyota corolla 2000

2007 & NEWER TOYOTA TUNDRA SPORT DUTY UNDERCARRIAGE MOUNTING INSTRUCTIONS

0

Filed Under (Toyota Manuals) by admin on 01-04-2012

download
The mounting procedure outlined below covers the 2007 and Newer Toyota Tundra trucks. You will need to refer to the illustrations and familiarize yourself with each of the undercarriage components and their relative position to each other. Then proceed as follows: 1. Begin by removing the bolts holding the skid plate to the bottom of the frame and the rear cross member. Remove the skid plate. Do not discard the skid plate or bolts so that they can be reinstalled if the undercarriage is removed. 2. Remove the two bolts from both tow hooks. Remove both tow hooks. Retain the bolts as they will be reinstalled further into the installation procedure. Do not discard the tow hooks so that they can be reinstalled if the undercarriage is removed. 3. Remove the three bumper mount nuts located on the front end of the driver side frame rail. Retain the nuts as they will be reinstalled further into the installation procedure. 4. Place Driver Side Push Beam Support Plate (62B) against the bottom of the driver side truck tow hook mount and against the outside of the driver side frame rail. The front tab of Push Beam Support Plate (62B) must clear the bumper mount studs on the front end of the truck frame. 5. Slide Driver Side Push Beam Support Plate (62B) backward until the three bumper mount studs on the end of the truck frame fully engage the three holes located on Driver Side Push Beam Support Plate (62B). 6. Reinstall the three bumper mount nuts that were removed in step 3. Fasteners should only be finger tight. 7. Assemble Driver Side Push Beam Support Plate (62B) to the tow hook mount using the two bolts removed in step 2. Fasteners should only be finger tight. 3 8. Using Bolt Puller (102) insert one ½” X 1-½” Hex Head Bolt (A) through the hole located on the outside of the driver side frame rail and through the hole located in Driver Side Push Beam Support Plate (62B). Secure with one ½” Split Lock Washer (D) and one ½” Hex Head Full Nut (C). Fasteners should only be finger tight. 9. Tighten the truck tow hook bolts. The heads of these bolts will not be accessible once Push Beam (62) is installed. 10. Repeat steps 3-9 for Passenger Side Push Beam Support Plate (62A). 11. Slide three Nut Plates (101) through the truck cross member. Align Nut Plates (101) with the front side of the two large outside holes and large center hole. 12. Place Angle Bracket (75) against the bottom of the truck cross member. Secure with three ½” X 1-½” Hex Head Bolts (A) and three ½” Split Lock Washers (D) and Nut Plates (101) previously installed inside the truck cross member. Fasteners should only be finger tight. 13. Install Push Beam (62) between Passenger Side and Driver Side Push Beam Support Plates (62A & 62B) using eight ½” X 1-½” Hex Head Bolts (A) and eight ½” Nylon Lock Nuts (B). Push Beam (62) should be mounted at a height of 14-½” from the ground to the center of the hook hole. Fasteners should only be finger tight. 14. Assemble Angle Bracket (75) to Push Beam (62) using four ½” X 1-½” Hex Head Bolts (A) and four ½” Nylon Lock Nuts (B). Fasteners should only be finger tight. 15. Tighten all fasteners, starting with Angle Bracket (75) and continuing forward. 16. With all undercarriage parts in place, securely fasten all mounting hardware. It is important that all fasteners be properly torqued (see Fig. 3) to assure a safe operating plow. Re-tighten all fasteners after 2 hours of plowing.

Related Content:

2007 sorento center bearing, how to install a pushnut

2007 Toyota Camry Rear Bumper Removal and Replacement Manual

0

Filed Under (Toyota Manuals) by admin on 26-01-2012

download
REMOVAL 1. REMOVE REAR BUMPER ASSEMBLY (w/o Rear Lower Spoiler ) a. Put protective tape around the rear bumper assembly. b. Using a screwdriver, open the 2 rear bumper plates. HINT: Tape the screwdriver tip before use. c. Remove the 6 screws and 2 clips. d. Disengage the 12 claws and disconnect the rear bumper assembly as shown in the illustration HINT: Use the same procedures for the RH side and LH side. e. Remove the rear bumper assembly. 2. REMOVE REAR FLOOR BOARD (w/ Rear Lower Spoiler ) a. Remove the 4 screws, 2 clips, 3 nuts and rear floor board. 3. REMOVE REAR BUMPER ASSEMBLY (w/Rear Lower Spoiler ) a. Put protective tape around the rear bumper assembly. b. Using a screwdriver, open the 2 rear bumper plates. HINT: Tape the screwdriver tip before use. c. Remove the 6 screws. d. Disengage the 12 claws and disconnect the rear bumper assembly as shown in the illustration. HINT: Use the same procedures for the RH side and LH side. e. Remove the rear bumper assembly. INSTALLATION 1. INSTALL REAR BUMPER ASSEMBLY (w/o Rear Lower Spoiler ) a. Engage each claw.

Related Content:

2005 F250 Ford Truck rear brake backing plate, how to remove rear bumper 2008 camry, time it takes to repair front bumper for 2007 toyota camry

Toyota Tacoma 13013 Installation Instructions

0

Filed Under (Toyota Manuals) by admin on 28-02-2012

download
GROSS LOAD CAPACITY WHEN USED AS A WEIGHT CARRYING HITCH: 5,000 lbs. trailer weight & 500 lbs. tongue weight. GROSS LOAD WHEN USED WITH A WEIGHT DISTRIBUTING HITCH: 6,000 lbs. trailer weight & 600 lbs. tongue weight. DO NOT EXCEED VEHICLE MANUFACTURER’S RECOMMENDED TOWING CAPACITY! 1. Disconnect the license plate wiring connectors from the bumper. 2. Remove the two bolts mounting the bumper to the bumper brackets on each side. Remove the bumper from the vehicle. 3. Remove bumper brackets from frame rails and the two bolts each side. 4. Position the receiver against the frame and install 1/2″ bolts and block through the rearmount hole in the frame rail into angle bracket. 5. Re-install bumper brackets over receiver side bracket placing tab through hole provided in side bracket. 6. Re-install bumper using existing fasteners removed in step 2 and adjust bumper and reconnect license plate wiring connection. Tighten M12, CL8.8 Fasteners to 68 lb-ft. Tighten 1/2″-13 Grade 5 Fasteners to 75 lb-ft

2007 Toyota Tundra MOUNT KIT INSTALLATION MANUAL

0

Filed Under (Toyota Manuals) by admin on 29-02-2012

download
INSTALLATION INSTRUCTIONS NOTE: For easier assembly and installation, vehicle and all snowplow components should be on a smooth, level, hard surface, such as concrete. 1. On the driver side of the truck, remove the outermost fastener securing the plastic bumper cover to the splash pan. Retain the fastener for reinstallation if the plow is removed. Then, fold the outermost tab on the plastic bumper cover up to allow for easier pushplate installation. 2. Trim the splash pan as shown to allow for easier pushplate installation. 3. Repeat Steps 1 and 2 on the passenger side. Remove and retain fastener. Fold outermost tab up. Trim as shown below. Tow Hook (Passenger side shown.) (Driver side shown.) Trim splash pan. Do not cut into spot welds. On the driver side of the truck, remove the tow hook fasteners and tow hook. Retain the tow hook for reinstallation if the plow is removed. Retain the fasteners for reinstallation in the following step. 5. Attach the driver-side pushplate to the truck frame using the original tow hook fasteners. Tighten the fasteners so that the pushplate is firmly against the bottom of the frame, but do not fully tighten at this time. 6. Using the rear holes in the driver-side pushplate as guides, drill two 13/32″ holes into the truck frame. 7. Insert two 3/8″ x 1-1/4″ cap screws with handles and 3/8″ flat washers into the inside of the truck frame and out through the rear drilled holes. Attach a 3/8″ locknut to each cap screw and hand tighten. CAUTION Use caution not to pinch, cut or drill through any wires or hoses running along the frame rail. 8. Repeat Steps 4-7 on the passenger side of the truck. 9. Install the cross bar using four 1/2″ x 1-1/2″ cap screws and 1/2″ locknuts. Hand tighten fasteners. 10. Check for a connecting arm distance of 29-1/8″ ± 1/8″. If the connecting arm distance is not within 29-1/8″ ± 1/8″, then loosen the tow hook fasteners on one or both pushplates and shift the pushplate(s) in the appropriate direction to obtain the desired dimension. 11. Tighten all fasteners according to the torque chart after achieving the appropriate dimensions. NOTE: Install the 29596 Headlamp Extension Bracket Kit to the headgear according to the instructions included with the bracket kit. NOTE: After five to ten hours of snowplow usage, retorque all pushplate assembly fasteners. NOTE: Customer, changing the oil on this vehicle requires the removal of the lower splash pan. Removal of the mount cross bar (4 fasteners) is required to removed this splash pan. Re-install both splash pan and cross bar and tighten all fasteners according to the torque chart.

Toyota Tundra Front Winch Bumper Installation Instructions

0

Filed Under (Toyota Manuals) by admin on 15-11-2011

download
Installation Instructions Toyota Tundra Front Winch Bumper Product Number: H1850, H1851, H1852 Application: ’07-Current Toyota Tundra Copyright sing a deep 14mm socket and breaker bar, loosen the 4 14mm nuts located at the connection between the factory frame end and the bumper. See Image Below. G. Remove the bumper by pulling forward away from the vehicle and rolling forward. H. Remove the two (per side) plastic clips from the painted plastic trim pieces located below the headlights. The Hood must be open for this. See Image Below. I. Remove these plastic painted trim pieces by pulling directly away from the front of the truck. Do not discard these! J. Remove all pop rivets (8 Total) from the front painted plastic bumper upper fascia. See Image Below. K. Remove all bolts holding the painted plastic fascia piece using a 10mm socket and wrench (16 total). See Image Below in addition to Image Above. L. Remove the Phillips pop rivet holding the fascia to the inner fender. 1 per side. M. Remove the two(one per side) 10mm screws from the recessed hole in the inner fender well. N. Pull the edges of the plastic fascia from the truck and directly away from the front to snap free. Set fascia aside. O. Remove the two 10mm screws using a socket from the plastic spacer pieces located on the lower fender. With Screws removed pull bracket straight off the truck. Complete on opposite side. See Image Below Pre-Installation Assembly A. Remove the Bumper from the shipping carton. Lay all items out on a blanket to prevent damage to the powder coating. B. OPTIONAL: If installing winch and roller fairlead (neither provided) into bumper, do it at this time. Follow the winch Manufacturers instructions to mount the fairlead to the front of the bumper and the winch itself to the 4 hole pattern on the internal winch tray of the bumper. C. Install turn signal into light pockets as shown using self- tapping screws as shown below.

2001-2007 Toyota Highlander MOUNTING BRACKET KIT INSTALLATION INSTRUCTIONS

0

Filed Under (Toyota Manuals) by admin on 27-03-2012

download
This bracket kit fits the 2001-10 Toyota Highlander. For the ’01-’07 Toyota Highlander, follow the instructions below. For ’08-’10 Toyota Highlander instructions, see the separate section included in these instructions. Important: please use all supplied bolts and parts and read all instructions carefully before beginning this installation. The majority of questions you may have can be answered within the text, and proper installation will ensure safe and secure travel. Now, begin the installation. Fig.C Fig.D Fig.E 1. Start by removing four plastic fasteners that attach the grille to the core support (Fig.C). 2. Once all the fasteners are removed, squeeze and push out a square plastic clip fastener for the grille, located between the headlight housing and the radiator support frame on each side. 3. Pull back the grille and remove the Phillips screw that attaches the fascia to the hood latch support (Fig.D). 4. On each side, remove three plastic fasteners: two of the plastic fasteners are attaching the fender liner to the fascia (Fig.E); the other plastic fastener is attaching the fender liner to the frame rail (Fig.F) 5. Remove ten 10mm (head) bolts (Fig.G) and two plastic fasteners (Fig.H) attaching the lower splash shield to the fascia and the sub frame. 6. On both sides, pull back the fender liner and remove one 10mm screw attaching the corner of the fascia to the fender (Fig.I). Fig.K Plastic fastener MOUNTING BRACKET KIT INSTALLATION INSTRUCTIONS ROADMASTER, Inc. 6110 NE 127th Ave. Vancouver, WA 98682 1-800-669-9690 fax 360-735-9300 KIT# 1180-1 05/14/10 KS 9. Remove the foam shock absorption core by pulling forward (Fig. L). Note: this will not be reinstalled. Retain the foam shock absorption core and attachment hardware so that it can be replaced if the bracket is ever removed. 10. Remove six 14mm (head) bolts to remove the bumper core (Fig.M). Note: this will not be reinstalled. Retain the bumper core and attachment hardware so that it can be replaced if the bracket is ever removed. 11. Remove the alignment studs at the end of each frame rail (Fig.N). 12. Now, place the main receiver brace into the ends of the frame rails (Fig.O). 13. Bolt the main receiver brace into place using the three supplied 10mm x 1.25 x 35mm bolts, flat washers and lock washers (Fig.P). Repeat for the other side. Tighten to the torque specifications listed at the end of these instructions.

Related Content:

how to remove the radiator grill on a 2002 toyota highlander, yhs-synd1, banjo meter model MFM220, plastic bezel 1203 manual, TH350 set end play, remove 2007 toyota highlander grille clips youtube, plastic bezel 1312 watch alarm setting, medline mattress manuals online, instructions for removing altenator 2001 honda civic, gen590 watch

2007 TOYOTA FJ CRUISER TOWING HITCH Installation Preparation

0

Filed Under (Toyota Manuals) by admin on 29-10-2011

download
1. Prepare for Installation. (a) Verify kit contents (b) Wear safety glasses. (c) Raise vehicle. (d) Caution muffler might be hot NOTE: Apply masking tape to quarter panels above the bumper fascia. To prevent damage when removing the bumper fascia, apply masking tape on the underside of the bottom left- hand corner of the door and left hand upper corner of door. (Fig. 1-1) 2. Prepare Vehicle for Rear Bumper Fascia Removal. (a) Open rear door (Fig. 2-1). (b) Protect exhaust tip with a rag or protective tape during installation of hitch. (Fig. 2-1) NOTE: If the vehicle is equipped with proximity sensors, detach the sensor wire connector from inside the fascia, behind the rear wheels on both sides of the vehicle (Fig. 2-2). Fig.2-1 Fig.2-2 Masking Tape Fig. 1-1 TOYOTA FJ CRUISER 2007 – TOWING HITCH Section II Installation Procedure Page 3 of 6 pages Issue: B 03/01/06 3. Remove Rear Bumper Fascia. NOTE: Protect rear bumper to prevent damage from tools (i.e. air tools) when removing the fascia bolts. (a) Remove the 13 6 mm hex head bolts (A) from rear bumper fascia. (Fig. 3-1) (b) Remove one (1) push pin (B) from fascia (Fig. 3-1) (c) Unsnap the sides of the fascia from the vehicle. (Fig. 3-2) (d) With one person on each end, remove fascia from vehicle. Store in a safe place to avoid damage during installation. (Fig. 3-2) 4. Install Hitch. (a) Install one (1) M12 x 45 bolt into the 13 mm hole as shown (Bolt 1). (Fig. 4-1) (b) Install two (2) M12 x 45 bolts in the lower slots (Bolts 2 & 3). (Fig. 4-1) (c) Install three (3) M12 x 45 bolts in the 15mm holes (Bolts 4 to 6). (Fig. 4-1) Fig. 4-1 – 3/8″ socket wrench – 17 mm socket – 6″ extension 3

Related Content:

08921-35870, Toyota FJ Cruiser tow hitch install

Related Content:

how to remove chevy sonic front bumper, INSTALLING A FRONT BUMPER ON THE TOYOTA RAV 4, replacing front bumper end cap on 2012 Toyota FJ cruiser, 2004fordf150frontbumperdiagram, 2000 4runner step bumper rear chrome install instructions, remove back bumper on kia sedona, remove 2006 toyota matrix rear bumper, remove back bumper on kia sedona cover, rear fender for 2008 camry, prius steering wheel pad removal instructions