Skip to content

toyota t50 transmission

You search PDF repair manual about toyota t50 transmission, if there are search results will appear below. If search results do not exist, please search by others keyword.

Toyota Landcruiser Prado clutch release bearing Removal And Installation Manual

download
1. Withdraw the transmission approximately 30 mm. 2. Insert a flat blade screw driver between the collar and bearing. 3. Twist screw driver 90 degrees and remove the bearing. 1. Locate the clutch release bearing on the gearbox front bearing retainer (snout). 2. Locate the throw out fork on the release bearing. 3. Position transmission to the engine block. 4. Operate the fork opposite direction for clutch release. 5. This will snap the bearing into the cover assembly. F : – 037 Toyota Landcruiser Prado 3.0L 1KD-FTV

TOYOTA 4RUNNER A750E (F) AUTOMATIC TRANSMISSION SERVICE MANUAL

download
The ATF level gauge (dip-stick) has been discontinued, and the ATF inspection method and the oil level inspection method have been changed. This mechanism consists of a refill plug, overflow plug, ATF temperature sensor No.2, and A/T OIL TEMP temperature warning light. ATF Filling procedures using SST (09843-18020): When a large amount of ATF needs to be filled (i.e. after removal and installation of oil pan or torque converter), perform the procedure from step 1. When the small amount of ATF is required (i.e. removal and installation of the oil cooler tube, repair of oil leak), perform the procedure from step 7. 1) Raise the vehicle keeping it level. 2) Remove the refill plug and overflow plug. 3) Fill ATF from the refill plug until it overflows from the overflow plug. 4) Install the overflow plug. 5) Fill the specified amount of ATF determined by procedure and install the refill plug. Example 6) Lower the vehicle down. 7) Use the SST (09843-18020) to short the terminals Tc and CG of the DLC3 connector: 8) Start the engine and allow it to idle. A/C switch must be turned OFF. 9) Move the shift lever slowly through each of the positions from the P to the L position, and move it back to the P position. 10) Move the shift lever from the D position, and quickly move then back and forth between N and D (once per less than 1.5 seconds) for at least 6 seconds. This will activate the oil temperature detection mode. Standard: The A/T OIL TEMP warning light remains illuminated for 2 seconds and it goes off. 11) Return the shift lever to the P position and disconnect the terminal Tc. 12) Idle the engine to raise the oil temperature. 13) Immediately after the ATF OIL TEMP warning light turns on, lift the vehicle up. The A/T OIL TEMP warning light will indicate the ATF temperature according to the following table. (Insert table here) 14) Remove the overflow plug and adjust oil quantity. If the ATF overflows, go to step 17, and if the ATF does not overflow, go to step 15. 15) Remove the refill plug. 16) Fill ATF to the refill plug until it flows out from the overflow plug. 17) When the ATF flow slows to a trickle, install the overflow plug. 18) Install the refill plug (only if the refill plug has been removed). 19) Lower the vehicle down. 20) Turn the ignition switch OFF to stop the engine. For details about the ATF Filling procedures, see the 2004 4Runner Repair Manual (Pub. No. RM1059U)

1996 Toyota Supra A/T TRANSMISSION REMOVAL AND INSTALLATION MANUAL

download
Removal 1) Disconnect negative battery cable. Remove battery, battery tray, air cleaner assembly and air cleaner case. Disconnect throttle valve cable from throttle body. Remove cruise control actuator with mounting bracket from body. 2) Raise and support vehicle. Disconnect necessary electrical connectors and ground cables for transaxle removal. Disconnect shift cable and oil cooler lines at transaxle. Remove shift cable clamp bracket from transaxle. 3) Remove front (radiator side) engine mount shock absorber- to-lower frame assembly bolts. Remove front (radiator side) engine mount-to-lower frame assembly bolts/nuts. Remove starter. 4) Remove front (radiator side) exhaust manifold brace from rear of exhaust manifolds. Brace fits between rear of exhaust manifold and front of transaxle. 5) Remove 4 upper transaxle-to-cylinder block bolts. Support engine with hoist. Steering gear assembly must be supported in place during transaxle removal. Secure steering gear assembly to engine hoist using an attaching strap placed at each end of steering gear assembly. 6) Remove front wheels. Remove front exhaust pipe located between exhaust manifolds and rear exhaust pipe. Drain transaxle fluid. Remove axle shafts from transaxle. See appropriate AXLE SHAFTS article in AXLE SHAFTS & TRANSFER CASES section. 7) Disconnect shift control cable from mounting bracket. Remove rear (firewall side) engine mount-to-lower frame assembly bolts/nuts. Remove transaxle mount-to-transaxle bolts at driver’s side end of transaxle. 8) Remove stabilizer bar mount bracket-to-lower frame assembly bolts. Remove steering gear assembly-to-lower frame assembly bolts/nuts. Support lower frame assembly with floor jack. Lower frame assembly is located below engine and transaxle. 9) Disconnect power steering reservoir pipe mounting brackets from lower frame assembly. Remove bolts for each fender liner from lower frame assembly. Remove lower frame assembly mounting brackets. Lower frame assembly mounting brackets are located on front and rear of lower frame assembly and attach lower frame assembly to body. Remove lower frame assembly. 10) Support transaxle with transmission jack. Remove torque converter cover from front of transaxle. Remove torque converter bolts. Remove remaining exhaust manifold support brace. Remove remaining transaxle-to-cylinder block bolts. Lower transaxle from vehicle.

1996 Toyota Supra M/T TRANSMISSION REMOVAL AND INSTALLATION MANUAL

download
REMOVAL & INSTALLATION WARNING: To prevent air bag deployment, disconnect negative battery cable and wait at least 90 seconds before working on vehicle. CAMRY Removal & Installation 1) Disconnect negative battery cable. Remove air cleaner case with air intake hose. Remove cruise control actuator. Remove clutch release cylinder with hose attached and secure aside. 2) Remove starter. Disconnect necessary ground straps, electrical connections and control cables from transaxle. Remove upper transaxle mounting bolts from cylinder block. 3) Raise and support vehicle. Remove front wheels. Remove lower engine covers. Drain transaxle fluid. Remove axle shafts from transaxle. See appropriate AXLE SHAFTS article in AXLE SHAFTS & TRANSFER CASES section. Remove stabilizer bar mount and bushing from crossmember. 4) Support steering gear so steering gear remains in place. Remove steering gear-to-crossmember bolts and nuts. Remove front exhaust pipe, located below oil pan. Remove stiffener plates, located between cylinder block and transaxle, at rear of oil pan. 5) Support engine with hoist. Remove front (exhaust manifold side) engine mount-to-crossmember bolts and nuts. Remove rear (intake manifold side) engine mount-to-crossmember nuts. 6) Using transmission jack, slightly raise transaxle to remove weight from engine mounts. Remove transaxle mount-to-transaxle bolts and transaxle mount-to-crossmember nuts. Disconnect necessary pipes and clamps from crossmember. Remove bolts, nuts and crossmember, located below engine and transaxle. 7) Support transaxle with transmission jack. Remove remaining transaxle mounting bolts. Slightly lower engine and remove transaxle. To install, reverse removal procedure. Tighten nuts and bolts to specification. See TORQUE SPECIFICATIONS. WARNING: To prevent air bag deployment, disconnect negative battery cable and wait at least 90 seconds before working on vehicle

2010 Toyota Highlander Performance And Specifications

download
MECHANICAL Mechanical/Performance Hybrid engine — 3.3-liter double overhead cam (DOHC), 24-valve VVT-i V6; 208 hp (156 kW) @ 5600 rpm, 212 lb.-ft. @ 3600 rpm Gasoline engine — 2.7L double overhead cam (DOHC) 16-valve dual VVT-i; 187 hp @ 5800 rpm, 186 1b.-ft. @ 4100 rpm Gasoline engine — 3.5-liter double overhead cam (DOHC) 24-valve dual VVT-i V6; 270 hp @ 6200 rpm, 248 lb.-ft. @ 4700 rpm Emission Rating SULEV [1] ULEV-II Evaporative emission certification — zero evaporation Electric Motor Function: Drive front wheels, regeneration during braking Electric motor type: Permanent magnet motor Power output: 167 hp (123 kW) @ 4500 rpm Maximum torque: 247 lb.-ft. @ 0-1500 rpm Maximum voltage: AC 650V Rear Electric Motor Function: Drive rear wheels, regeneration during braking Motor type: Permanent magnet motor Power output: 68 hp (50 kW) @ 4610-5120 rpm Maximum torque: 96 lb.-ft. @ 0-610 rpm Maximum voltage: AC 650V Traction Battery Battery Type: Sealed Nickel Metal Hydride (Ni-MH) Maximum power output: 45 kw Voltage: 288V Hybrid System Net Power: 270 hp (201 KW) Hybrid Performance [2] Top track speed [2] (electronically limited) Ignition system Electronic, with Toyota Direct Ignition (TDI) Transmission — Gasoline models 6-speed Electronically Controlled automatic Transmission with intelligence (ECT-i) (4- cyl.) 5-speed Electronically Controlled automatic Transmission with intelligence (ECT-i), sequential shift mode and Snow Mode Transmission — Hybrid models Electronically Controlled Continuously Variable Transmission (ECVT) with ECON mode