Skip to content

toyota tacoma rear jack point

You search PDF repair manual about toyota tacoma rear jack point, if there are search results will appear below. If search results do not exist, please search by others keyword.

2005-2008 TOYOTA TACOMA 4 X 4 AND PRE RUNNER 3″ SUSPENSION LIFT KIT INSTALLATION INSTRUCTIONS

download
Tacoma Installation Instructions 09/09/08 INST-426A.DOC Page 2 of 7 FRONT OF TACOMA 1. Park vehicle on level concrete surface. 2. Center and lock the steering wheel. 3. Block the rear wheels of the vehicle to prevent vehicle from moving in either direction. 4. Jack up the vehicle from the lift point in Figure A. 5. Support the vehicle with jack stands from the points in Figure A. 6. Remove the front wheels. 7. Remove sway bar end links from spindle using 17mm socket (both sides). See Figure B. 8. Remove front skid plate using 12mm socket. 9. Remove sway bar from frame using 14mm socket. See Figure C. 10. Using 19mm socket, remove lower bolt and nut from the bottom of the strut (both sides). 11. Remove cotter key and 19mm nut from outer tie rod end, rack & pinion utilizing a tie rod end puller (or pickle fork). 12. Remove the three nuts (14mm) from the top of the strut. See Figure D. 13. Remove the struts from the vehicle, making sure that they are marked driver and passenger side respectively for reinstallation. NOTE: AT THIS TIME, IF YOU DO NOT HAVE A SUITABLE SPRING COMPRESSOR, IT IS HIGHLY ADVISED TO EITHER TAKE THE STRUT TO A QUALIFIED SERVICE CENTER OR PURCHASE THE REVTEK SC-1 SPRING COMPRESSOR. 14. Compress strut assembly and remove the nut (17mm) on the top of the strut shaft. 15. Release the compressor. 16. Remove the spring top plate from the strut. 17. Remove and discard the rubber spacer Tacoma Installation Instructions 09/09/08 INST-426A.DOC Page 3 of 7 FRONT OF TACOMA (continued) 18. Remove (hammer) the studs from the spring top plate. See Figure “F.” 19. Install (hammer) the LONGER STUDS (10MM) (provided) in the spring top plate. See Figure “G.” 20. Install the PRELOAD SPACER between the spring and the spring top plate with the small diameter facing toward the spring and the Revtek Industries logo facing outward. See Figure H. 21. Compress the strut assembly, making sure you center the strut shaft through the spring top plate hole and that the STUDS line up with the PRELOAD SPACER reliefs. Replace nut on the top of the strut shaft and torque to spec. (Torque specs can be found on page 1.) 22. Install the TOP OUT EXTENDER over the STUDS (Figure H). 23. Reinstall the strut by reversing the removal procedure; torque to spec. (Torque specs on page 1.) 24. When properly installed, Revtek Industries logo will be centered between preload spacer reliefs. 25. Reinstall tie rod ends, torque to spec. 26. Reinstall sway bar to frame. 27. Reinstall sway bar end links into spindles. Torque to spec

1995-2004 TOYOTA TACOMA 4 X 4 AND PRERUNNER 3″ SUSPENSION LIFT KIT INSTALLATION INSTRUCTIONS

download
Tacoma 4WD & PreRunner Installation Instructions Page 3 of 7 09/09/08 INST-425F.DOC FRONT OF VEHICLE 1. Park vehicle on level concrete surface. 2. Center and lock the steering wheel. 3. Block the rear wheels of the vehicle to prevent vehicle from moving in either direction. 4. Jack up the vehicle from the lift point in Figure “A.” 5. Support the vehicle with jack stands from the points in Figure “A.” 6. Remove the front wheels. 7. Remove the nut (14mm) and the hardware from the anti-sway bar. See Figure “B.” 8. Remove the nut (19mm) and bolt (14mm) from the bottom of the strut. See Figure “C.” 9. Remove the three nuts (14mm) from the top of the strut. See Figure “D.” 10. Remove the strut from the vehicle. NOTE: AT THIS TIME, IF YOU DO NOT HAVE A SUITABLE SPRING COMPRESSOR, IT IS HIGHLY ADVISED TO EITHER TAKE THE STRUT TO A QUALIFIED SERVICE CENTER OR PURCHASE THE REVTEK SC-1 SPRING COMPRESSOR. 11. Compress strut assembly and remove the nut (17mm) on the top of the strut shaft in Figure “E.” 12. Release the compressor. 13. Remove the spring top plate from the strut. 14. Remove and discard the rubber spacer. 15. Remove (hammer) the studs from the spring top plate. See Figure “F.” 16. Install (hammer) the LONGER STUDS (10MM) (provided) in the spring top plate. See Figure “G.” 17. Install the PRELOAD SPACER between the spring and the spring top plate with the small diameter facing toward the spring. See Figure “H.” 18. Compress the strut assembly, making sure you center the strut shaft through the spring top plate hole and that the STUDS line up with the PRELOAD SPACER reliefs. Replace nut on the top of the strut shaft and torque to spec. (Figure “E”). (Torque specs can be found on page 1.) 19. Install the TOP OUT EXTENDER over the STUDS (Figure “H”). 20. Reinstall the strut by reversing the removal procedure; torque to spec. (Torque specs on page 1.) 21. When properly installed, PRELOAD SPACER relief and Revtek Industries logo should face outward. (Figure R) 22. Reinstall hardware and nut on anti-sway bar; torque to spec. 23. Replace the wheels; torque to spec.

Toyota Tacoma extra cab Rear Jump Seats Installation Manual

download
INSTRUCTION Toyota Tacoma extra cab Rear Jump Seats Dear Customer, As we are unable to assist you on installing your Wet Okole Hi. Waterproof sport seat covers we offer these special instructions. This particular instruction is a universal instruction for Toyota Tacoma rear bench. Mostly all other vehicles are self explanatory. Any problems please feel free to call for technical support at 1(888)24-Okole. Enjoy your Wet Okole Hawaii Seat Covers! Step1 Step2 Next: With a pair of dull plastic pry tools ora pair of butterknives pry the rest cushion up with one tool and tuck seat cover under rest cushion with the other. Fold both seat cushions forward and slip seat cover over cushion and attach velcro. Note: Rear plastic rest may need to be removed from vehicle to allow easy seat cover installation. Note: Tuck cover underneath plastic. Note: Backrest panel maybe removed by pulling panel off of rear cab, there are 6 plastic plugs on the back of the panel that snap into the rear firewallofthecab.

Toyota Tacoma extra cab Rear Jump Seats

download
As we are unable to assist you on installing your Wet Okole Hi. Waterproof sport seat covers we offer these special instructions. This particular instruction is a universal instruction for Toyota Tacoma rear bench. Mostly all other vehicles are self explanatory. Any problems please feel free to call for technical support at 1(888)24-Okole. Enjoy your Wet Okole Hawaii Seat Covers! I Step2 Next: With a pair of dull plastic pry tools ora pair of butterknives pry the rest cushion up with one tool and tuck seat cover under rest cushion with the other. Fold both seat cushions forward and slip seat cover over cushion and attach velcro. Note: Rear plastic rest may need to be removed from vehicle to allow easy seat cover installation. Note: Tuck cover underneath plastic. Note: Backrest panel maybe removed by pulling panel off of rear cab, there are 6 plastic plugs on the back of the panel that snap into the rear firewallofthecab.

2004 – 2006 Toyota Sienna Vehicles Equipped w/ Power Back Door (Power Rear Liftgate) Repair Manual

download
Certain 2004 – 2006 Model Year Sienna vehicles equipped w/Power Back Door (Rear Liftgate) Q1: What is the condition? A1: Toyota has determined that the gas struts used to help lift and support the Power Rear Liftgate in certain 2004 through 2006 model year Sienna vehicles could be wearing out sooner than expected. As the gas struts deteriorate, the performance of the Power Rear Liftgate will begin to degrade, and the Power Rear Liftgate will operate more slowly than when the gas struts were new. Only Sienna vehicles equipped with the Power Rear Liftgate are involved. Q2: Are there any warnings that this condition exists? A2: Owners may notice that the Power Rear Liftgate will not remain in the open position. If not repaired, the gas struts may not be able to support the weight of the liftgate when it is open, and eventually, the gas struts could deteriorate to the point that the liftgate will fall about ten inches after it reaches the fully open position, at which point the power motor will engage and power the liftgate to the fully closed position. This condition may cause injury to a person who is struck by the liftgate when it falls or when it is closing. Q3: When were these vehicles produced, and how many vehicles are involved? A3: Only certain 2004 through 2006 model year Sienna vehicles equipped with the Power Rear Liftgate, produced between January 2003 and December, 2006 are involved. Approximately 196,000 vehicles are involved nationwide.