Skip to content

toytota rav4 2008 engine push start button smart key programming instructions

You search PDF repair manual about toytota rav4 2008 engine push start button smart key programming instructions, if there are search results will appear below. If search results do not exist, please search by others keyword.

2007 Toyota Camry equipped with the Smart Key System with Push Button Start Remote Starter Integration

download
Material required: – Remote Car Starter – Xpresskit : XK05-PKT2 or Bypasskit :PKT2 – One 5-wire relay for auto lamp circuit Key required for programming: 1 Average installation time: 2.5 hours Difficulty level: Medium 2.0 Preparation: -Remove the driver’s side under dash, as well as the knee airbag bolts. Move the Airbag aside, but DO NOT DISCONNECT the Airbag connector in order to avoid setting any vehicle codes. -Remove the driver’s side floor heating duct, in order to access the vehicle IMI & IMO wires easily. 3.0 Installation: The remote car starter will be installed in a conventional manner even if the car is equipped with the Smart Key “Push-to-Start” system. 3.01 Main Ignition Harness Connection: Most of the connections will be done behind the Fuse box. This fuse box is located under the driver side underdash. Also, the vehicle’s TACH wire can be found inside vehicle, as per diagram below and it is suggested to use this wire for the remote start tach source. The remote start hood pin switch wire is the only wire which must be run into the engine compartment for safety. Accessory (+): White Ignition 1 (+): Pink Ignition 2 (+): Light Green Starter (+): Grey Tach: Black 3.02 Wiring location for the Bypasskit XK-05 PKT2: The connection for the XK05-PKT2 will be done on the driver side under dash. The wires required are from a 5 wires harness coming from behind the heater module, high above the gas pedal near the firewall. The five wires in this harness are as follows: Blue: transponder IMI (Immobilizer in) wire, which gets cut in two and wired in series. The bottom-half wire connects to the kits Violet/White wire and the top-half wire connects the kits Violet wire. Green: transponder IMO (Immobilizer out) wire, which gets wired in parallel with the kits Orange wire. White/Black, White & Orange… these wire are not used for installation The GREEN LED output wire from the XK05-PKT2 is not required for this installation. The vehicle LED does come on during remote start. 3.03 Wiring location for door locks and factory alarm control: The wires to control the factory alarm and the door locks are located behind the driver’s kick panel. These wires must receive negative pulses. It is mandatory to disarm the OEM alarm system before remote start sequence Grey Unlock Wire : A double pulse unlock (-) output is required to disarm and unlock all doors. The first unlock (-) pulse disarms OEM alarm and unlocks driver’s door, the second pulse will unlock all other doors. In order to disarm the OEM alarm when remote starting, this GREY wire requires a pulse before start, which unlocks the driver’s door. So, if the remote systems unlock output does offer a pulse before start, then connect both the unlock and disarm (-) output wires to the vehicle’s GREY unlock wire. Brown Lock Wire : In order to lock and arm the OEM alarm system a (-) pulse is required for the vehicle’s BROWN lock wire. If the vehicle’s ignition on the alarm will not arm, if locking with remote.

NISSAN ALTIMA OR SENTRA W /QR25 ENGINE NO-START AFTER COLD SOAK REPAIR MANUAL

download
SERVICE PROCEDURE Replace Starter, Add Cleaner 1. Replace the starter motor. • Use the part number from the Parts Information section of this bulletin. • Refer to section SC, “STARTING SYSTEM, Removal and Installation” in the applicable Nissan Electronic Service Manual (ESM). 2. Add one full can of Nissan In-Tank Fuel System Cleaner to the fuel. NOTE: If the fuel tank is less than ¾ full, instruct the customer to fill the tank as soon as it is convenient after the repair. Driving with the Cleaner installed and low fuel level will not harm the fuel system or engine, but will reduce the effectiveness of the cleaning process. 3. Continue to ECM Part Number Check (next page). 1. With CONSULT-II “ON”, print the Self-DIAG Results as follows: START (Nissan) >> ENGINE >> Self-DIAG Results >> PRINT SELF-DIAG RESULTS SYSTEM ENGINE DATE XX/XX/XXXX* 11:07:11 P/N 23710-XXXXX TP020389h DTC RESULTS TIME NO DTC IS DETECTED Current ECM Part Number * Example, your screen may differ. 3. Using the printout from Step 1: • Compare the vehicle’s current ECM P/N to those shown under Current ECM P/N in Chart 1, below: • This comparison will allow you to determine if the ECM needs to be reprogrammed. Chart 1, Current ECM P/N’s: VEHICLE PACKAGE NATS? CURRENT ECM P/N A/T, ASCD YES 23710-9J305, -9J003, -9J002, -9J001, -9J000, -8J001, -8J000 M/T, ASCD YES 23710-9J315, -9J013, -9J012, -9J011, -9J010, -8J061, -8J060 A/T, no ASCD YES 23710-9J300, -9J008, -9J007, -9J006, -9J005, -8J011, -8J010 02-04 Altima M/T, no ASCD YES 23710-9J310, -9J018, -9J017, -9J016, -9J015, -8J071, -8J070 YES 23710-8U542, -8U541, -8U540, -8U041, 8U040 A/T NO 23710-8U502, -8U501, -8U500, -8U001, 8U000 YES 23710-8U562, -8U561, -8U560, -8U061, -8U060 02-03 Sentra 5 M/T NO 23710-8U512, -8U511, -8U510, -8U011, -8U010 YES 23710-8U072, -8U071, -8U070 02 Sentra 6 M/T NO 23710-8U022, -8U021, -8U020 YES 23710-8U572, -8U571, -8U570 03 Sentra 6 M/T NO 23710-8U522, -8U521, -8U520 NOTE: The 2004 Sentra ECM does not need to be reprogrammed for this bulletin. A. If your vehicle’s ECM P/N matches a P/N in the chart above: • Perform ECM Reprogramming (page 4). B. If your vehicle’s ECM P/N does not match a P/N in the chart above: • ECM Reprogramming is not necessary, bulletin complete / end here

1997-1998 Buick Regal GS & Pontiac Grand Prix GTP with L67 3.8L V6 Engine Fuel Pump Resistor Service Procedure

download
The following are instructions for removing the fuel pump resistor from its original mounting location on the lower right front body rail as shown in Figure 1, and replacing it with a new fuel pump resistor and cover in new location shown in Figure 2. The new location is on the front of dash sheet metal (3) at the rear of the engine compartment, inboard or to the left of the alternator (4). The passenger or right side windshield wiper arm (5) and stop (6) are called out for reference purposed only. 1. Turn the steering wheel to the full right position. 2. Open the hood and disconnect the negative battery cable. 3. Remove the diagonal brace (1) from over the windshield washer solvent reservoir by removing the two bolts (2) that attach it to the radiator support and the one bolt (3) that attaches it to the strut tower. Refer to Figure 3 4. Remove the two plastic push-in retainers (1) that attach the windshield washer solvent reservoir (2) to the radiator support (3) and the one nut (4) that attaches it to the strut tower (5). Refer to Figure 4. 5. Reposition the reservoir for access to the area rearward of the battery. 6. Raise the vehicle on a hoist. 7. At the right front wheel opening, remove the three screws that attach the inner fender splash shield to the front fascia at the wheel opening and the two screws that attach it to the bottom of the fascia. Refer to Figure 5. 8. Reposition the inner fender splash shield (1) to access the fuel pump resistor (2). Refer to Figure 1 at the beginning of this procedure. 9. Unclip the fuel pump resistor electrical connector from the body and disconnect the connector. 10. Remove the 10mm hex head bolt attaching the fuel pump resistor to the body and discard both the bolt and the resistor.

4.6L Mustang Bassani Mid Length Headers INSTALLATION INSTRUCTIONS

download
INSTALLATION INSTRUCTIONS 1. Disconnect the battery. 2. Safely raise & support vehicle to a comfortable working height. (One jack stand at each corner of vehicle.) 3. Spray attaching hardware and base of o2 sensors with WD40 or similar Lubricant. Remove 02 sensors from stock system. (Be careful not to damage or contaminate sensor). Stock gasket will be re-used upon assembly. 4. Remove both connector tubes between stock exhaust manifold and Bassani Modular X pipe. It may be necessary to loosen downstream clamps on the Bassani Modular X pipe. 5. Loosen EGR fitting on drivers side exhaust manifold. It will be necessary to remove nuts from the motor mounts at the K member to jack engine up. Motor mount heat shields have to be removed. 6. Loosen & remove both exhaust manifolds. 2 valve, stock manifold gaskets, depending on condition, may be re-used . Remove studs from both sides. Use supplied, and/or stock hardware. See note following #10. 7. Label wiring on starter and remove it. (Will be necessary for header installation) 8. You may also need to remove oil filter to ease installation and tightening on drivers’ side. 9. IMPORTANT! It will be necessary to unbolt steering shaft from rack. With a marker draw a straight line on shaft down to rack to index them both. Do not move front wheels or steering wheel. 10. It will be necessary to lift engine up enough to slide header tubes in and have access to install supplied header bolts. After loosening motor mount bolts, lifting engine (using a wooden block under oil pan) and removing motor mounts, one side at a time only, will ease installation. Removal of motor mounts is not mandatory. **Anti seize must be applied to all threads (header bolts and studs). It may be necessary to use a combination of header bolts and stock studs & nuts on certain tubes due to clearance between the tube and hardware. ie; stud nut or header bolt. The use of either is the installers preference. 11. Start on passenger side, with tube #1R. Push as far forward as possible to allow clearance for #2R. Once #2R is in position, install gaskets, and header bolts. When this is completed commence installation of #3R and #4R tubes following previous procedure. Leave bolts loose, DO NOT TIGHTEN UNTIL COLLECTOR IS INSTALLED. 12. When Collector R is ready for right side, place Bassani anti seize jet lube , on slip connectors to ease installation. When collector lines up with tab on header tube, fasten them together and tighten all header tubes. 13. When all hardware is properly tightened, lower engine, re-install motor mount hardware, starter and O2 sensors in collector. The use of Bassani anti seize Jet Lube is recommended on O2 sensor threads. Do not to contaminate O2 sensor bulb with lube. 14. Proceed to drivers’ side. Install #1L with gasket installed. Install supplied fasteners with Bassani anti seize jet lube on the threads. DO NOT TIGHTEN ALL THE WAY, leave semi loose. Install tube #3L, then #2L. You will need to experiment with pipes #2L and #3L. #2L will slip between #3L and #1L. Now install #4L, fasten and screw air fitting to tube #4L. Install Collector L . When collector tab lines up with header tab, tighten all hardware, and bolt on EGR, and any smog fittings. Lower engine and re-install motor mount hardware. Reconnect steering shaft using loctite 271 thread locker on bolt.

TOYOTA TO CHEVY AND BUICK ENGINE – TURBO CHARGED INSTALLATION INSTRUCTIONS

download
INSTALLATION INSTRUCTIONS: 1. Install the pilot bushing into the engine crank. 2. Bolt the flywheel to the engine crank using special flywheel bolts. 3. Assemble the clutch assembly and special disc to the flywheel using special clutch bolts. 4. Assemble the clutch release arm to the inside ball pivot of the bellhousing. 5. Bolt the slave cylinder to the outside of the bellhousing. 6. Test fit the bellhousing assembly over the clutch assembly and onto the engine block. 7. Place the N1430 release bearing onto the clutch arm fork. 8. Adjust the length of the slave cylinder push rod to a length that provides a minimum of 1/8″ clearance between the release bearing face and clutch fingers. 9. This test fit over the clutch assembly is primarily done for establishing the push rod length. If this procedure is eliminated, you will not have any visual inspection for verifying the push rod adjustment. 10. Remove the bellhousing assembly from the engine. 11. Bolt the bellhousing to the front of your Toyota 5 speed transmission using the original bolts. Make sure that the two dowel pins installed in the face of the 5 speed transmission are properly fitted to the Advance Adapter bellhousing. 12. Slide the new release bearing onto the Toyota bearing retainer. Make sure that there is grease in the internal cavity of the release bearing. Most new bearings are pre-lubricated. 13. With all the components in position, you can now bolt the new bellhousing assembly onto the engine block. We have provided six (6) new socket head bolts, 3/8″-16 x 1-1/2″ long for this purpose. Make sure the engine dowel pins are properly aligned with the new bellhousing dowel pin holes. DO NOT FORCE THE BELLHOUSING ONTO THE ENGINE BLOCK. Some applications may require the tip of the input shaft to be modified slightly. The bellhousing must fit evenly to the engine block. 14. With the bellhousing now in position and the slave cylinder push rod installed, you should be able to verify the clearance between the release bearing & clutch fingers. The lever should have movement of approximately 1/8″ to 1/4″. CAUTION : If you have too much clearance, you will be utilizing too much of the slave cylinder stroke and could possibly prevent you from obtaining a full clutch release. A light duty return spring attached to the clutch release arm will prevent any premature contact of the release bearing with the clutch fingers. 15. The Toyota Land Cruiser slave cylinder will replace the original Toyota slave cylinder. The Toyota truck hydraulic slave cylinder line will have exactly the same fitting size as used on the Land Cruiser slave cylinder. 16. With the new slave cylinder installed, you can now bleed the slave cylinder installation by pumping up the slave cylinder pedal. Most installations are compatible with the original Toyota master cylinder. We have encountered a few installations that require changing of the Toyota master cylinder to a smaller 3/4″ piston. If you have any type of clutch difficulty related to full disengagement of the clutch assembly, contact Advance Adapters for any updated information.