trailer brake module fault ford f250

You search PDF repair manual about trailer brake module fault ford f250, if there are search results will appear below. If search results do not exist, please search by others keyword.



  trailer brake module fault ford f250 Direct Download speed 5432 Kb/s

  trailer brake module fault ford f250 Full Version speed 8172 Kb/s



2008 Ford Taurus AWD V6-3.5L – Rear Brake Pads Removal And Installation Manual

0

Filed Under (Ford Manuals) by admin on 25-06-2012

download
Removal WARNING: Do not use any fluid other than clean brake fluid meeting manufacturer’s specification. Additionally, do not use brake fluid that has been previously drained. Following these instructions will help prevent system contamination, brake component damage and the risk of serious personal injury. WARNING: Carefully read cautionary information on product label. For EMERGENCY MEDICAL INFORMATION seek medical advice. In the USA or Canada on Ford/Motorcraft products call: 1-800-959-3673. For additional information, consult the product Material Safety Data Sheet (MSDS) if available. Failure to follow these instructions may result in serious personal injury. CAUTION: Brake fluid is harmful to painted and plastic surfaces. If brake fluid is spilled onto a painted or plastic surface, immediately wash it with water. CAUTION: Do not allow the brake fluid to come in contact with the adhesive backing on the brake pads. If brake fluid is spilled onto the brake pads, new pads must be installed. CAUTION: Use only specified brake parts cleaner. Use of other cleaners may leave a residue on the brake caliper preventing the brake pads adhesive surface from bonding with the brake caliper. 1. Remove the wheel and tire. 2. Check the brake fluid level in the brake fluid reservoir. * If required, remove fluid until the brake master cylinder reservoir is half full. 3. Remove the brake caliper bolts. 4. CAUTION: Do not use the brake caliper sight hole to retract the pistons as this may damage the pistons and boots. CAUTION: Do not allow the caliper to hang from the brake hose or damage to the hose may occur. CAUTION: Care must be taken when servicing rear brake components without disconnecting the parking brake cable from the brake caliper lever. Carefully position the caliper aside using a suitable support or damage to the parking brake cable end fittings may occur. Using hand force and a rocking motion, separate the brake caliper from the anchor plate. Position the brake caliper aside. * Support the caliper with mechanic’s wire. 5. CAUTION: When the brake pads are separated from the brake caliper , new brake pads must be installed to prevent brake noise. The brake pads are one-time use only. Remove and discard the brake pads and spring clips from the brake caliper anchor plate. 6. NOTE: Do not remove the anchor plate guide pins. The guide pins are press fit to the brake caliper anchor plate. If the guide pins are damaged a new anchor plate must be installed. Inspect the brake caliper anchor plate assembly. * Check the guide pins and boots for binding or damage. * Install a new brake caliper anchor plate if it is worn or damaged. Installation 1. NOTE: To move the piston back into the caliper, the LH piston is turned clockwise and the RH piston is turned counterclockwise. NOTE: A moderate to heavy force toward the caliper piston must be applied. If sufficient force is not applied, the internal park brake mechanism clutch cone will not engage and the piston will not compress. Using the special tool (or equivalent such as OTC tool 7317A), compress the brake caliper piston into its cylinder. 2. Clean the residual adhesive from the brake caliper fingers and pistons using the specified brake parts cleaner. 3. CAUTION: Do not allow grease, oil, brake fluid or other contaminants to contact the brake pad or caliper mating surface or damage to components may occur. Do not install contaminated pads. NOTE: Install all the new hardware supplied with brake pad kit. Install the new spring clips and brake pads. 4. Position the brake caliper and install the 2 bolts. * Tighten to 29 Nm (21 lb-ft). 5. If necessary, fill the brake fluid reservoir with clean, specified brake fluid. 6. With the vehicle engine running, apply 89-133 N (20-30 lb) of pressure on the brakes for approximately one minute, to make sure the brake pads adhere to the caliper before any contamination can be introduced. 7. Test the brakes for normal operation.

Related Content:

diagram of a 2004 chev thoe break line sysetm, hummer h3 brake job, isuzu npr brake adjustment, rear disk brake assembly on 2000 Saturn, isuzu npr brake booster removal instruction, 2002 ford ranger brake bleeding procedure, front brake line diagram on 2004 tahoe, how bleed bakes on 1998 chevy malibu, replace avalon caliper piston boot, repair manual for toyota yaris brakes

2003 Volvo XC90 2.5T L5-2.5L Turbo Brake Pad Service and Repair Manual

0

Filed Under (Volvo Manuals) by admin on 12-06-2012

download
Brake Pad: Service and Repair Rear Brake Pads Brake Pads Rear, Replacing NOTE: The illustrations in this service information are used for different model years and/or models. Some variation may occur. However, the essential information in the illustrations is always correct. Preparations Remove the wheels on both sides. Removing brake pads NOTE: Minimum recommended pad thickness/replacement limit when installing new brake pads = 3.0 mm . Remove the retaining springs and locating pins for the brake calipers. Remove: -the securing spring (3) carefully so that it does not deform -the protective caps (1) from the two locating pins (2) -the locating pins, use hex socket 7 mm . Remove: 2003 Volvo XC90 2.5T L5-2.5L Turbo VIN 59 B5254T2 9.50 Page 1 Brake Pad: Service and Repair Rear Brake Pads Brake Pads Rear, Replacing NOTE: The illustrations in this service information are used for different model years and/or models. Some variation may occur. However, the essential information in the illustrations is always correct. Preparations Remove the wheels on both sides. Removing brake pads NOTE: Minimum recommended pad thickness/replacement limit when installing new brake pads = 3.0 mm . Remove the retaining springs and locating pins for the brake calipers. Remove: -the securing spring (3) carefully so that it does not deform -the protective caps (1) from the two locating pins (2) -the locating pins, use hex socket 7 mm . Remove: 2003 Volvo XC90 2.5T L5-2.5L Turbo VIN 59 B5254T2 Copyright © 2007, ALLDATA 9.50 Page 2 -the brake caliper from the holder -the brake pads. Hang the brake caliper in a steel wire from the rear spring so as not to damage the brake hose. NOTE: Do not depress the brake pedal while the brake pads are removed. Cleaning the brake caliper 2003 Volvo XC90 2.5T L5-2.5L Turbo VIN 59 B5254T2 Copyright © 2007, ALLDATA 9.50 Page 1 Brake Pad: Service and Repair Rear Brake Pads Brake Pads Rear, Replacing NOTE: The illustrations in this service information are used for different model years and/or models. Some variation may occur. However, the essential information in the illustrations is always correct. Preparations Remove the wheels on both sides. Removing brake pads NOTE: Minimum recommended pad thickness/replacement limit when installing new brake pads = 3.0 mm . Remove the retaining springs and locating pins for the brake calipers. Remove: -the securing spring (3) carefully so that it does not deform -the protective caps (1) from the two locating pins (2) -the locating pins, use hex socket 7 mm . Remove:
2003 Volvo XC90 2.5T L5-2.5L Turbo VIN 59 B5254T2 Copyright © 2007, ALLDATA 9.50 Page 2 -the brake caliper from the holder -the brake pads. Hang the brake caliper in a steel wire from the rear spring so as not to damage the brake hose. NOTE: Do not depress the brake pedal while the brake pads are removed. Cleaning the brake caliper 2003 Volvo XC90 2.5T L5-2.5L Turbo VIN 59 B5254T2 Copyright © 2007, ALLDATA 9.50 Page 3 Clean and check the brake caliper and dust cover. Clean and check the brake pad mating surfaces in the brake caliper and caliper holder. Check piston dust boot. NOTE: If the dust boot is damaged dirt may have penetrated the cylinder. If this is the case the caliper must be replaced. Checking the brake disc Check brake disc friction surfaces. If the brake disc displays signs of out-of-true, check its lateral run out. Replace the brake disc if it displays signs of heavy wear, variable thickness or similar. NOTE: Minimum disc thickness/replacement limit = 18.0 mm . Minimum recommended disc thickness when installing new brake pads = 18.7 mm . Installation Installing the brake pads

Related Content:

volvo xc90 2 5t turbo, 2009 scion xb rear pad replacement, 20020 envoy how to replace brake dustshield, f53 brake replacement, D12VolvoManual Printable, 2005 4runner brake rotor removal, tools needed to change brakes on 2008 pontiac torrent, change brake pads 2008 scion, cavalier 2003 service manual, 2003 volvo v40 headlight screws manual

2005 Ford F-Super Duty 250-550 Auxiliary Brake System/ Trailer Brake Control (TBC) Module Repair Manual

0

Filed Under (Ford Manuals) by admin on 14-06-2012

download
connected to the vehicle, the TBC module will enter a “sleep mode” but still continue to send a PWM voltage signal to the trailer tow connector every 4 seconds to detect when a trailer is connected. When the ignition key is in the RUN position and the module is in sleep mode, pressing a gain button or sliding the manual switch will cause the module to “wake up”. If a trailer is not connected to the vehicle, the display should prove out for 3 seconds, then the trailer icon should illuminate red and the IC message center should display TRAILER DISCONNECTED or CHECK TRAILER. If a trailer is connected to the vehicle, the display should prove out for 3 seconds and then the trailer icon should illuminate green. Inspection and Verification NOTE: A trailer brake emulator tool is available to verify that the TBC module and vehicle wiring are functioning correctly. 1. Verify the TBC system is correctly installed by checking that the vehicle is equipped with a brake pressure transducer on the master cylinder. If the brake pressure transducer is not present, then the TBC system has been erroneously installed. 2. Verify the customer concern. 3. NOTE: The TBC does not function with electric-over-hydraulic or surge trailer brake types. Verify that the trailer brakes are electric-actuated drum type brakes. 4. Verify the stoplamps operate correctly by applying and releasing the brake pedal with the ignition switch in the OFF position and the trailer disconnected. If the stoplamps do not operate correctly, refer to Section 417-01 . If the stoplamps operate correctly, proceed to the next step. 5. Visually inspect for obvious signs of mechanical or electrical damage. Visual Inspection Chart 6. If the cause is not visually evident, connect the scan tool to the data link connector (DLC) and select the vehicle to be tested from the scan tool menu. If the scan tool does not communicate with the vehicle: * check that the program card is correctly installed. * check the connections to the vehicle. * check the ignition switch position. 7. If the scan tool still does not communicate with the vehicle, refer to the scan tool operating manual. 8. Carry out the scan tool data link test. If the scan tool responds with: * CAN, ISO, or UBP circuit fault; all electronic control units no response/not equipped, refer to Section 418-00 . * No response/not equipped for the TBC, GO to Pinpoint Test A . * System passed, retrieve and record the continuous diagnostic trouble codes (DTCs), erase the continuous DTCs, and carry out self-test diagnostics for the TBC and the antilock brake system (ABS) module. 9. If the DTCs retrieved are related to the concern, go to the Trailer Brake Control (TBC) module Diagnostic Trouble Code (DTC) Chart or Anti-Lock Brake System (ABS) Module Diagnostic Trouble Code (DTC) Chart to continue diagnosis. 10. If no DTCs related to the concern are retrieved, GO to Symptom Chart to continue diagnosis. NOTE: Always retrieve the continuous DTCs after running the self-test.

Related Content:

2005 f150 security module, 2007 ford f250 tbc fault, 2008 Ford sd brake pressure transducer, an i program a ford abs module, ford tbc fault, programming abs module ford, tbc falt on 2005 ford f350

2003 Volvo S40 L4-1.9L Rear Brake Pads Removal And Installation Manual

0

Filed Under (Volvo Manuals) by admin on 16-02-2012

download
the hub cap and the wheel * the retaining clip and the brake hose from the support * the upper bolt from the locating pin for the brake caliper . Twist the brake caliper backwards. Remove the brake pads. NOTE: Do not depress the brake pedal while the brake pads are removed. Checking and cleaning the rear brake calipers Clean brake pad contact surfaces in the brake caliper and on the caliper mounting. Check the dirt guard for the piston. Replace the dirt guard if it is worn. Recondition the brake caliper if the dirt guard is defective. NOTE: If the dirt guard is defective, dirt may have penetrated the cylinder. Therefore the brake caliper must be reconditioned. Checking the rear brake disc Check the brake disc surface. Check the lateral runout of the brake disc if the disc is uneven. Replace the brake disc if it is worn or grooved. NOTE: Minimum disc thickness = 8.4 mm . If installing new brake pads, the minimum disc thickness must be at least 8.9 mm . Checking the locating pins for the rear brake calipers Check the rubber sleeves on the locating pins. Replace if necessary. If necessary, lubricate the locating pins using Volvo silicon grease (P/N 1161325-4). Insert the locating pins in the rubber sleeves. The locating pins must slide into the sleeves easily. Rotating the brake piston backwards Block the brake caliper against the brake disc. Use special tool 999 5782. * Turn the plate (A) forward over the shaft and insert the tool * Install the lugs (B) in the cut-out in the brake piston * Turn the shaft (C) so that the plate (A) presses against the brake caliper * Turn the axle (D) to the right and press the piston back while turning the shaft (C) to the right so that the plate (A) is in contact with the brake caliper * Turn the brake piston back fully and remove the tool Install the wear indicator (A) on the under side of the inner installed brake pads. Install the brake pads. Position the brake caliper . Install the new locking bolt. Tighten to 33 Nm . Install the brake hose in the support. Install the retaining clip. NOTE: Secure adhesive foil onto the steel plates to prevent the rear brake pads from rattling. Installing the wheels Install wheels. Checking the brake fluid level WARNING: Always depress the brake pedal repeatedly before test driving the car. Check the brake fluid level

Related Content:

yukon air ride hose locking clip

2007 Volkswagen Rabbit BRAKES Brake System removing and installing

0

Filed Under (Volkswagen Manuals) by admin on 18-01-2012

download
Fig. 49: Torque Wrench V.A.G 1331 Courtesy of VOLKSWAGEN UNITED STATES, INC. * Torque wrench V.A.G 1331 Fig. 50: Piston Resetting Tool T10145 Courtesy of VOLKSWAGEN UNITED STATES, INC. * Piston resetting tool T 10145 Brake pads, removing When removing, mark brake pads that will be used again. Install in the same position, otherwise braking effect will be uneven! * Remove wheels. Fig. 51: Locating Brake Wear Pad Indicator Connector Courtesy of VOLKSWAGEN UNITED STATES, INC. * Disconnect connector – 1 – for brake pad wear indicator. Fig. 52: Protective Caps Courtesy of VOLKSWAGEN UNITED STATES, INC. * Remove caps – arrows -. Fig. 53: Removing/Installing Brake Caliper Guide Pins Courtesy of VOLKSWAGEN UNITED STATES, INC. * Loosen both guide pins – arrows – and remove from brake caliper. * Remove brake caliper and secure with wire so that the weight of the brake caliper does not burden or damage the brake hose. * Remove brake pads from brake caliper. Cleaning: * Thoroughly clean contact surfaces for brake pads at brake carrier, remove corrosion. * Clean brake caliper. Use only appropriate solvents for cleaning brake caliper. Brake pads, installing Before pressing piston into cylinder using piston resetting tool, brake fluid must be extracted from brake fluid reservoir. Otherwise, especially if reservoir has been topped off, fluid will overflow and cause damage. Fig. 55: Identifying Brake Pad Retaining Springs Courtesy of VOLKSWAGEN UNITED STATES, INC. * Insert inner brake pad (piston side) – 1 – and outer brake pad – 2 – with retaining springs into brake caliper. * Inner brake pad (piston side) with large three-finger clip – 1 -. * Outer brake pad with small three-finger clip – 2 – (colored black). Fig. 56: Identifying Lower Part Of Brake Caliper Housing Courtesy of VOLKSWAGEN UNITED STATES, INC. * Place brake caliper with brake pads on brake carrier first at bottom – arrow

2004 Ford Explorer/Mountaineer Anti-Lock Brake System (ABS) Module Diagnostic Trouble Code (DTC) Index Repair Manual

0

Filed Under (Ford Manuals) by admin on 20-05-2011

download
C1963 Stability Control Inhibit Warning ABS Module This DTC is for information only. CLEAR the DTC. REPEAT the self-test. C1991 Module Calibration Failure ABS Module Follow the diagnostic tool directions for the calibration procedure. C1996 Active Yaw Control Disabled ABS Module This DTC will be set if the stability assist system is activated for 15 seconds of continuous operation. CHECK for any major chassis modifications, gross suspension misalignment, or other items that can alter the vehicle tracking dynamics. CLEAR the DTC. REPEAT the self-test. C1998 Module Calibration Not Complete ABS Module Go To Pinpoint Test Q . C2769 (ABS only) Longitudinal Acceleration Sensor Circuit Failure ABS Module CLEAR the DTC. REPEAT the self-test. If DTC C2769 is present, INSTALL a new ABS module. REFER to Anti-Lock Brake System (ABS) Module in this section. C2769 (ABS with stability assist) Longitudinal Acceleration Sensor Circuit Failure ABS Module Go To Pinpoint Test H . C2770 (ABS with Stability Assist) Longitudinal Acceleration Sensor Signal Fault ABS Module Go To Pinpoint Test H . C2770 (ABS only) Longitudinal Acceleration Sensor Signal Fault ABS Module CLEAR the DTC. REPEAT the self-test. If DTC C2770 is present, INSTALL a new ABS module. REFER to Anti-Lock Brake System (ABS) Module in this section. C2777 Sensor Cluster Bus Failure ABS Module Go To Pinpoint Test H . C2778 Sensor Cluster Power Supply Failure ABS Module Go To Pinpoint Test H . U1900 CAN Communication Bus Fault-Receive Error Network Fault Section 418-00 . U1901 CAN Network #2 Communication Bus Fault- Receive Error Network Fault Go To Pinpoint Test H . U2023 Fault received from external node Network Fault Section 418-00

Related Content:

WHERE IS 2002 DAKOTA CENTRAL TIMING MODULE, ABS fault on Tahoe, hino 05 air brake fail abs, where is yaw sensor located on a 2002 ford explorer, isuzu npr fuse panel location, how to replace vats module on 1997 buick lesabre, gmc hvac relearn, ford u1901 steering angle sensor, ford u1901 escape, ford relearn after abs sensor trans harsh

2004 Toyota Camry Disc Brake System Service/ Repair Manual

0

Filed Under (Toyota Manuals) by admin on 13-04-2012

download
OVERHAUL HINT: Overhaul the RH side by the same procedures with LH side. REMOVE FRONT WHEEL 1. DRAIN BRAKE FLUID NOTICE: Wash off the brake fluid immediately if it comes into contact with a painted surface. 2. DISCONNECT FRONT FLEXIBLE HOSE 3. Remove the union bolt and a gasket from the disc brake cylinder, then disconnect the flexible hose from the disc brake cylinder. a. REMOVE DISC BRAKE CYLINDER ASSY FR LH 4. Remove the 2 bolts and disc brake cylinder. a. REMOVE DISC BRAKE PAD KIT FRONT (PAD ONLY) 5. Remove the 2 brake pads with anti-squeal shim. a. 6. Remove the 2 anti-squeal shims from each of 2 brake pads . a. Using a screwdriver, remove the wear indicator from each of 2 brake pads . b. REMOVE FRONT DISC BRAKE PAD SUPPORT PLATE 7. Remove the upper side front disc brake pad support plate. a. REMOVE FRONT DISC BRAKE PAD SUPPORT PLATE 8. Remove the bottom side front disc brake pad support plate. a. 10. Remove the cylinder slide bush from the cylinder slide pin. a. REMOVE FRONT DISC BRAKE BUSH DUST BOOT 11. Remove the 2 bush dust boots from the disc brake cylinder mounting. a. REMOVE FRONT DISC BRAKE CYLINDER MOUNTING LH 12. Remove the 2 bolts and disc brake cylinder mounting LH. a. 13. Using a screwdriver, remove the set ring and cylinder boot. a. REMOVE FRONT DISC BRAKE PISTON 14. Place a piece of cloth or similar, between the piston and the disc brake cylinder. a. Use compressed air to remove the piston from the disc brake cylinder. CAUTION: Do not place your fingers in front of the piston when using compressed air. NOTICE: Do not spatter the brake fluid . b. 2004 Toyota Camry L4-2.4L (2AZ-FE) REMOVE PISTON SEAL 15. Using a screwdriver, remove the piston seal from the disc brake cylinder. NOTICE: Do not damage the inner cylinder and the cylinder groove. a. REMOVE FRONT DISC BRAKE BLEEDER PLUG CAP 16. REMOVE FRONT DISC BRAKE BLEEDER PLUG 17. INSPECT BRAKE CYLINDER AND PISTON Check the cylinder bore and piston for rust and scoring 18.

Related Content:

Remove front rotor 2003 Highlander, 2006 ford 500 sel misfire engine, how to repair cylinder no 4 on 2007 dodge charger, cylinder set up on 2003 Escape, misfire on number 2 cylinder on kia sedona, how to eplace brake backing plate on 1997 F350 floating axle, how to repalce ignition switch on 2005 cts, how to replace cylinder head rav4 2004, misfire 2009 pontiac g6, 1940 dodge Master Cylinder Diagram

Electric Trailer Brake Controller Installation Manual

0

Filed Under (More Manuals) by admin on 10-05-2012

download
In connection with the installation of such devices, please note the following. 1. Check the installed rear SAM. If a rear SAM with part number A164 540 78 45 or A164 540 88 45 is currently installed, a new rear SAM must be installed and version coded. The current part number is listed in the parts information section below. The cost of this update is not covered by warranty. Note: Some vehicles without a factory trailer hitch are equipped with a rear SAM that requires replacement with a different rear SAM if trailer brakes are to be retrofitted. 2. Locate plug X58/28. This contains the four wires needed for the electric trailer brake controller Refer to the below for wire description. a. Up to December 2006 production, X58/28 (Figure 1, green plug) near the rear fuse box F4 (Figure 1). Plug may be tie wrapped to harness below Rear SAM. b. As of December 2006 production, X58/28 (Figure 2, green plug) near the diagnostic connector X11/4 (Figure 2). Plug may be tie wrapped to harness above connector X11/4. Figure 1 T-B-31/1907 Figure 2 T-B-31.19/07d Wire Description – X58/28 Color Size Description Red or Red /Blue 2.5 mm2 Fuse F4f71, 30 Amp fuse. This is the power supply for an electric trailer brake controller. Brown 2.5 mm2W7 ground. This is the ground wire for an electric trailer brake controller Grey or Black/Red 0.75mm2 Brake light circuit. This is the brake signal for an electric trailer brake controller (input to the electronic brake controller). Yellow/Red or Yellow/White 2.5 mm2 X58/11 pin 7. This is the variable voltage signal to actuate the trailer brakes (from the output of the electronic brake controller). Note: Most electric trailer brake controllers specify that the power supply must be wired using a self resetting circuit breaker. Follow the instructions supplied with the electric trailer brake controller. Note: The above variation in wire colors depends on production date of factory harness and or installed accessory harness. Warning! The electric trailer brake controller must be adjusted according to the instructions supplied with the electric trailer brake controller, which requires the trailer be connected to the tow vehicle

Related Content:

A164 540 88 45, 2006 dodge ram ac electrical diagrams, a164 690 02 10, highlander pop up camper fuse box

2004 Chrysler Pacifica DISC BRAKE SHOES Removal And Installation Manual

0

Filed Under (Chrysler Manuals) by admin on 13-05-2011

download
DISC BRAKE SHOES Removal (Front) 1. Remove master cylinder fluid reservoir cap. 2. Raise and support vehicle. 3. Remove tire and wheel assembly. 4. Place appropriately sized C-clamp over brake caliper, placing screw-drive head against outboard shoe and hook against rear of caliper. Slowly tighten screw-drive retracting caliper pistons into bores and brake outboard brake shoe free from caliper fingers. See Fig. 22 . Remove C-clamp. 5. Once outboard shoe is free from caliper fingers, slide caliper inboard on guides providing clearance between the rotor and inboard brake shoe. 6. Slide an appropriate prying tool through center opening in top of caliper behind brake shoe between 2 caliper pistons. Use care not to come in contact with pistons or dust boots potentially damaging them. Pry against rear of inboard brake shoe braking it free from caliper pistons. 7. Remove the 2 brake caliper guide pin bolts. See Fig. 23 . 8. Remove disc brake caliper from brake adapter and hang out of way using wire or a bungee cord. Use care not to overextend brake hose when doing this. 9. Remove brake shoes from disc brake caliper adapter. See Fig. 27 . 10. Install master cylinder fluid reservoir cap. 2. Install disc brake caliper over brake shoes on brake caliper adapter. See CALIPER . 3. Align guide pin bolt holes with guide pins and install caliper guide pin bolts. See TORQUE SPECIFICATIONS . 4. Install tire and wheel assembly. See TORQUE SPECIFICATIONS . 5. Lower vehicle. 6. Pump brake pedal several times to seat shoes to caliper and brake rotor. 7. Check and fill brake fluid level as necessary. See CHECKING & FILLING under BRAKE FLUID in SERVICE. 8. Road test vehicle making several stops to wear off any foreign material on brakes and to seat brake shoes. Removal (Rear) 1. Raise and support vehicle. 2. Remove both rear tire assemblies from vehicle. 3. Remove 2 caliper guide pin bolts. 4. Remove the 2 caliper guide pin bolts. See Fig. 24 . 5. Remove caliper from caliper adapter. See CALIPER . 6. Remove outboard brake shoe by pushing shoe away from caliper fingers, dislocating locating pins built into shoe backing plate from holes in caliper fingers, then sliding brake shoe down and off of brake caliper. See Fig. 28 . 7. Pull inboard brake shoe away from caliper piston, dislocating retaining clip from cavity in piston. Remove inboard shoe. NOTE: In some cases, it may be necessary to retract caliper piston in its bore a small amount in order to provide sufficient clearance between shoes and rotor to easily remove caliper from knuckle. This can usually be accomplished before guide pin bolts are removed, but grasping rear of caliper and pulling outward working with guide pins, thus retracting piston. DO NOT push on piston directly as it may get damaged.

Related Content:

4L80E Troubleshooting Guide, www motorcraftservice com owners guide, 2006 honda accord brake caliper torque, Mazda 6 Shop Manual PDF, proper torque for chevy truck pitman arm replacement 2004 avalanche, rear brake caliper removal on 2010 ford f-150, replacing caliper pin 2007 sienna, seville caliper exploded, slider bolts 2004 ford expedition, v reader repair

2004 Ford Expedition/ Navigator Brake Pads REMOVAL AND INSTALLATION

0

Filed Under (Ford Manuals) by admin on 26-01-2011

download
1. CAUTION: Install a new lining if worn 1 end with 2 tabs. If yes, the LH side anchor to or past the specified thickness above the housing spring must be installed with the metal backing plate or rivets. Install new 2-tabbed end in the upper brake caliper cavity. pads in complete axle sets. For the LH brake caliper, release the lower If necessary, using a suitable suction device, portion of the anchor housing spring. remove the brake fluid in the master cylinder •Apply force at the center of the anchor reservoir until it is half filled. housing spring and pull outward at the bottom of the anchor housing spring to 2. Remove the wheel and tire assembly. For remove it from the lower brake caliper additional information, refer to Section 204-04. cavity. 3. Inspect the brake pads for wear or contamination. 4. CAUTION: If the anchor housing spring is to be reused, do not force the anchor housing spring off the brake caliper. Do not install a damaged anchor housing spring. Remove the anchor housing spring. REMOVAL AND INSTALLATION (Continued) 6. Rotate the spring upward then remove it from the brake caliper. 9. NOTE: Do not allow the brake caliper to hang from the brake hose. Remove the brake caliper. 7. NOTE: On the RH side, the anchor housing 1 Remove the zero-drag spring. spring must be installed with the 2-tabbed end in the lower brake caliper cavity. The 2 Remove and discard the brake illustration below shows the anchor housing caliper-to-anchor plate bolts, guide pins and spring end with 2 tabs. boots. For RH brake caliper, release the upper portion of the anchor housing spring. •Apply force at the center of the anchor housing spring and pull outward at the top of the anchor housing spring to remove it from the upper brake caliper cavity. 10. Remove the brake pads from the brake caliper. 11. NOTE: Use a wood block or used brake pad to protect the brake caliper piston boots. Compress the brake caliper pistons. 8. Rotate the spring downward then remove it from the brake caliper.

Related Content:

installing break pads on 2004 exped

Related Content:

diagram of a 2004 chev thoe break line sysetm, hummer h3 brake job, isuzu npr brake adjustment, rear disk brake assembly on 2000 Saturn, isuzu npr brake booster removal instruction, 2002 ford ranger brake bleeding procedure, front brake line diagram on 2004 tahoe, how bleed bakes on 1998 chevy malibu, replace avalon caliper piston boot, repair manual for toyota yaris brakes