transfer case repair manuals

You search PDF repair manual about transfer case repair manuals, if there are search results will appear below. If search results do not exist, please search by others keyword.



  transfer case repair manuals Direct Download speed 5432 Kb/s

  transfer case repair manuals Full Version speed 8172 Kb/s



4WD Switch Indicator Lights Flashing, 4WD Inoperative, DTCs C0327, P0500, P0836, P1875 Set (Replace Encoder Motor Sensor, Reprogram TCCM, Inspect Front Drive Axle Engagement Sleeve for Damage/Repair if Necessary)

0

Filed Under (More Manuals) by admin on 22-06-2012

download
Correction Important: For ease of reassembly, shift the transfer case assembly to 2HI for the NV263 (NP1), or Neutral for the NV246 (NP8) prior to removing any components. For information on placing the NV246 (NP8) transfer case in NEUTRAL, see the procedure at the end of this bulletin. 1. Remove the transfer case and front axle/engine skid plates (if equipped). 2. Disconnect and position the front propeller shaft aside. 3. Disconnect the transfer case encoder motor wiring harness. 4. Remove the three (3) bolts that retain the encoder motor to the transfer case. 5. Separate the encoder motor assembly from the transfer case and place it on a work bench. Important: DO NOT REMOVE THE SCREWS INDICATED WITH THE (1) IN THE ABOVE ILLUSTRATION. 6. Remove the four screws on the outer perimeter of the encoder motor housing. Important: For proper timing and ease of reassembly, hold the gear in place as your remove the cover from the encoder motor assembly with your thumb or finger. 7. Carefully remove the cover from the encoder motor assembly. The cover has a seal on the bottom side. Place the cover in a position to protect this seal from damage and/or contamination. Important: Observe the location of the punch mark on the large gear in relation to the timing mark on the housing if the transfer case was placed in the 2HI for the NV263 (NP1), or Neutral for the NV246 (NP8). The timing marks should be within one tooth of proper alignment. If not, you must note the timing mark positions for reassembly. 8. Locate the two shims; one on the small gear and another on the larger gear. Set them aside on a clean surface for reuse. Important: After removing the large gear from the housing, a dark gray phenolic spacer should remain in the casting where the bottom of the large gear resides. Locate this spacer and save for reuse. 9. Carefully lift the large gear from the housing. The sensor and wiring harness will come with the gear. 10. Disconnect the wiring from the sensor. 11. Separate the sensor from the large gear.

Related Content:

encoder motor & encoder sensor for 2004 chev silverado z71

1999 Mercury Sable A/ T – Cooler Flushing Service Manual

0

Filed Under (Mercury Manuals) by admin on 31-01-2012

download
SERVICE PROCEDURE Prior methods of cooler flushing have not obtained the level of cooler cleaning and contaminant removal that is required to prevent repeat repairs. The “Turbo-Tank Heated Cooler Line Flusher” uses heated Automatic Transmission Fluid ( ATF ) and a pulsating action to loosen system contamination. Previous equipment used solvents to clean & flush coolers, lines and torque- converters. There are 2 issues with this method: Aerosol Solvents should never be used for several reasons. NOTE YOU MUST IDENTIFY THE RETURN COOLER LINE TO START THE BACK FLUSHING PROCEDURE. A quick way to identify the return cooler line (fluid coming out of the cooler and returning to the transmission) is to locate the return cooler line fitting on the transmission case . Refer to the following lists: Rear Wheel Drive ^Residual solvent contamination can cause damage to friction bonding materials within the transmission (Clutches and Bands). ^Lack of fluid heating and agitation prevents this method from completely removing contamination from lines, in-radiator coolers and auxiliary coolers Front Wheel Drive NOTE IF AN IN-LINE FILTER HAS BEEN INSTALLED IN THE COOLER LINE, IT MUST BE REMOVED BEFORE FLUSHING THE COOLER OR COOLER LINES. Purge the cooler and cooler line before flushing: Located on the “Turbo-Tank Heated Cooler Line Flusher” is a fluid transfer and purge valve. This valve can be used to purge the cooler and cooler lines of contaminated fluid before starting the back flush procedure of the fluid cooling system (refer to step 5a of this Service Procedure or Equipment instructions, supplied with the “Turbo-Tank Heated Cooler Line Flusher”). Flush Procedure -The TOP transmission case filling receives the return line. ^CD4E – The REAR or Pump End transaxle case fitting receives the return line. ^4F27E – The REAR or Cover End transaxle case fitting receives the return line. ^AXOD, AXODE, AX4S, AX4N, 4F50N – The BOTTOM transaxle cooler line fitting receives the return line. 1. Check and top off fluid level of the “Turbo-Tank Heated Cooler Line Flusher” tank with transmission fluid. 2. Allow the fluid in the flusher 15-30 minutes to heat up to 140°F (60°C) before using. 3. Install line adapters into the transmission cooler lines. 4. Attach the flusher’s blue line to the transmission return cooler line quick disconnect. 5. Attach the flusher’s red line to the transmission outlet cooler line quick disconnect. a. Follow equipment instructions, to purge cooler lines and cooler prior to starting flushing procedure (using factory installed purge valve and clear hose on “Turbo-Tank Heated Cooler Line Flusher”). 6. Allow the cooling system to back-flush for 10-15 minutes, then flush the cooler in a forward/normal flow direction for an additional 10-15 minutes.

Related Content:

c6 trans cooling line diagram, buick transmission cooler flush, rotor screw pontiac montiac 2007

2002 Mercury Sable V6-3.0L VIN 2 Flex Fuel Repair Manual

0

Filed Under (Mercury Manuals) by admin on 14-07-2012

download
Automatic Transmission/Transaxle Tune-Up B 0.0 1.5 Notes Includes: R&R Trans Pan, Service Filter And Make All Necessary Adjustments. Diagnose/Test AX4N/4F50N Oil Leak, Diagnosis B 0.0 0.5 Notes Includes: Clean And Dry Outside Of Case And Operating Unit To Determine Point Of Leakage. Transaxle, Diagnosis A 0.0 1.8 Notes Includes: Time To Hook-Up And Disconnect Test Equipment. Checking System For Fault Codes, Road Test And Hydraulic Pressure Test As Required. AXOD-E, AX4S Oil Leak, Diagnosis B 0.0 0.5 Notes Includes: Clean And Dry Outside Of Case And Operating Unit To Determine Point Of Leakage. Transaxle, Diagnosis A 0.0 1.8 Notes Includes: Time To Hook-Up And Disconnect Test Equipment. Checking System For Fault Codes, Road Test And Hydraulic Pressure Test As Required. Replace AX4N/4F50N Complete Assembly Without Transfer Of Parts B 5.0 7.3 Notes NOTE To R&R Driveplate, Add B 0.0 0.2 Notes To R&R Torque

Related Content:

P0715 fault code MPV, Toyota Rav -4 2012 air filter replacement on you tube, 1999 Chevrolet impala ss Po752, kod błędu p0502 buick, p2195 04 ford expedition, po462 ford taurus, Saturn Outlook Code P0496, u2023 code land rover 2006, volvo penta 5 0 gi code reader, what does code po464 on chevy

Related Content:

encoder motor & encoder sensor for 2004 chev silverado z71