troubleshooting isuzu npr glow plugs

You search PDF repair manual about troubleshooting isuzu npr glow plugs, if there are search results will appear below. If search results do not exist, please search by others keyword.



  troubleshooting isuzu npr glow plugs Direct Download speed 5432 Kb/s

  troubleshooting isuzu npr glow plugs Full Version speed 8172 Kb/s



Toyota Tundra , Sequoia NA Unichip PnP Installation Instructions

0

Filed Under (Toyota Manuals) by admin on 22-11-2011

download
1. Disconnect the truck’s battery a. Using a 10mm wrench, disconnect the truck’s battery at the negative terminal in the engine compartment. 2. Expose the OEM ECU a. (Photo 1) Locate the ECU on the passenger’s side of the engine compartment rear bulkhead. b. Rotate the top OEM plug’s grey locking lever “up” and disconnect the plug from the ECU. Note: The plugs have locking levers which must be rotated to remove and install the plugs. Do not force the locking levers or plugs c. Rotate the bottom OEM plug’s grey locking lever “down” and disconnect the plug from the ECU. Note: The plugs have locking levers which must be rotated to remove and install the plugs. Do not force the locking levers or plugs. Photo 1 ECU Photo 23. (Photo 3) Install the PnP harness. a. Install the large and small PnP Plugs into the OEM ECU and rotate the grey locking levers flush to secure them Note: The plugs have locking levers which must be rotated to remove and install the plugs. Do not force the locking levers or plugs b. Position the PnP Case vertically beside the OEM ECU, plug the small OEM plug into the PnP Case, and rotate the grey locking lever flush to secure it. The PnP Case should remain in position as shown in the photo. Note: The plugs have locking levers which must be rotated to remove and install the plugs. Do not force the locking levers or plugs c. Connect the large OEM plug into the PnP Case and rotate the grey locking lever to secure it. Note: The plugs have locking levers which must be rotated to remove and install the plugs. Do not force the locking levers or plugs

1981-1996 ISUZU Amigo/Pick-ups/Rodeo/Trooper Glow Plugs SYSTEM TESTING REMOVAL AND INSTALLATION MANUAL

0

Filed Under (Isuzu Manuals) by admin on 04-05-2012

download
SYSTEM TESTING See Figures 1, 2, 3 and 4 Fig. Fig. 1: Glow plug system schematic Fig. Fig. 2: Dropping resistor and glow plug relay locations Fig. Fig. 3: Thermo switch location Fig. Fig. 4: Dropping resistor check To test the dropping resistor, check for continuity across the terminals as described in the illustration. If no continuity exists, replace the unit. 1. To test the thermo switch, first remove the switch. Submerge the end of the switch in water and raise the temperature gradually. The switch should be off at 126-140°F (53-60°C) or lower. The switch should be on at 134-145°F (57-63°C) or higher. If not, replace the switch. 2. REMOVAL & INSTALLATION See Figure 5 Fig. Fig. 5: Location of the glow plugs The glow plugs are located under the injection nozzles, and are threaded into the cylinder head. Disconnect the negative (-) battery cable. 1. Disconnect the glow plug and unscrew it from the engine. 2. To install: Lubricate with anti-seize compound before installing the plug. 3. Install and tighten the plug to 65 ft. lbs. (88 Nm). 4. Reconnect the plug wiring. 5. Connect the battery cable and check operation. 6.

Related Content:

how to activate glow plugs on 2000 rodeo, if glow plug 0n an isuzu trooper is not working will it affect tha engine, lazyboy furniture repair manuals

2004 Chevrolet Aveo SPARK PLUG REMOVAL AND INSTALLATION MANUAL

0

Filed Under (Chevrolet Manuals) by admin on 12-06-2012

download
Courtesy of GENERAL MOTORS CORP. 2. Loosen the 4 bolts and remove the engine cover. Fig. 117: Identifying Spark Plug & Wire Courtesy of GENERAL MOTORS CORP. 3. Remove the spark plug wires from the spark plugs. Refer to Spark Plug Wire Replacement . 4. Remove the spark plugs from the engine. Courtesy of GENERAL MOTORS CORP. 2. Loosen the 4 bolts and remove the engine cover. Fig. 117: Identifying Spark Plug & Wire Courtesy of GENERAL MOTORS CORP. 3. Remove the spark plug wires from the spark plugs. Refer to Spark Plug Wire Replacement . 4. Remove the spark plugs from the engine. Fig. 118: Identifying Spark Plug & Wire Courtesy of GENERAL MOTORS CORP. NOTE: Be sure plug threads smoothly into cylinder head and is fully seated. Use a thread chaser if necessary to clean threads in cylinder head. Cross- threading or failing to fully seat spark plug can cause overheating of plug, exhaust blow-by, or thread damage. Follow the recommended torque specifications carefully. Over or under-tightening can also cause severe damage to engine or spark plug. 2. Install the spark plugs to the engine. Tighten: Tighten the spark plugs to 25 N.m (18 lb ft). 3. Install the spark plug wires to the spark plugs. Refer to Spark Plug Wire Replacement . Fig. 119: Identifying Cover Screws Courtesy of GENERAL MOTORS CORP. 4. Install the engine cover and tighten the 4 bolts. Tighten: Tighten the engine cover bolts to 3 N.m (31 lb in).

Related Content:

ISX 12 drain plug thred, changing spark plugs on 2008 avalon, 2004 chevy aveo spark plug wire replacement, Ford 500 Spark Plug Change, how to change spark plugs in 2009 Aveo, spark plug calibration, manual shifter not working on 2008 nissan titan, loctite spark plug, is 1999 pontiac grand am obd2, intermitant misfire in morning 2008 torrent

Ford 455C 555C 655C Tractor Loader Backhoe Service Manual

0

Filed Under (Ford Manuals) by admin on 23-05-2012

download
Engine Systems Chapter 1 3-Cylinder Diesel Engine 3-Cylinder Diesel Engine – Description and Operation 3-Cylinder Diesel Engine – Overhaul Chapter 2 4-Cylinder Diesel Engine 4-Cylinder Diesel Engine – Description and Operation 4-Cylinder Diesel Engine – Overhaul Chapter 3 Cooling System Cooling System – 3-Cylinder Engine Description and Operation Cooling System – 4-Cylinder Engine Description and Operation Cooling System – Overhaul Chapter 4 Troubleshooting, Specifications and Special Tools Troubleshooting Specifications Special Tools Part 2 Fuel Systems Chapter 1 Fuel System – General Fuel System – Description and Operation Fuel System – Adjustments DPA Distributor Type Fuel Injection Pump Fuel System – Adjustments DPS Distributor Type Fuel Injection Pump Fuel System – Fuel Tanks, Filters and Fuel Lines Overhaul Chapter 2 Fuel Injection Pump – DPA Distributor Type Fuel Injection Pomp – Description and Operation Fuel Injection Pump – Overhaul Fuel Injection Pump – ISO Test Conditions Fuel Injection Pump – Test Procedures Chapter 3 Fuel Injection Pump – DPS Distributor Type Fuel Injection Pump – Description and Operation Fuel Injection Pump – Overhaul Fuel Injection Pump – ISO Test Conditions Fuel Injection Pump – Test Procedure Chapter 4 Injectors Ford 455C Injectors – Description and Operation Injectors – Overhaul Chapter 5 Injectors Ford 555C and 655C Injectors – Description and Operation Injectors – Overhaul Chapter 6 Air Cleaners Dry Type Air Cleaner – Description and Operation Dry Type Air Cleaner – Overhaul Chapter 7 Turbocharger Turbocharger – Description and Operation Turbocharger – Overhaul Chapter 8 Troubleshooting, Specifications, Test Plans and Special Tools Troubleshooting – Diesel Engines Troubleshooting – Turbocharger Specifications Special Tools Test Plans Part 3 Electrical System Chapter 1 Wiring, Lights and Controls Wiring, Lights and Controls – Description and Operation Wiring, Lights and Controls – Fault Finding and Repair Circuit Diagrams and Wiring Harness Chapter 2 Battery
Battery – Description and Operation Battery – Maintenance and Tests Chapter 3 Starting System Starting System – Description and Operation Starting Motor – Overhaul Chapter 4 Charging System – A127 55 Amp Alternator with Integral Regulator Charging System – A127 55 Amp Alternator with Integral Regulator – Description and Operation Charging System – A127 55 Amp Alternator with Integral Regulator – Service Precautions, Preliminary Checks, Initial Tests and Alternator Component Tests Charging System – A127 55 Amp Alternator with Integral Regulator – Overhaul Chapter 5 Troubleshooting, Specifications and Special Tools Troubleshooting Specifications Special Tools Part 4 Power Reversing Transmission Chapter 1 4×4 Fully Synchronized Power Reversing Transmission Power Reversing Transmission – Description and Operation Introduction to Overhauling the Transmission Gear Shift Lever, Modulator Unit and Solenoid Control Valve – Overhaul Front End Overhaul Complete Overhaul Component Overhaul Chapter 2 8X8 Fully Synchronized Power Reversing Transmission Power Reversing Transmission – Description and Operation Introduction to Overhauling the Transmission Gear Shift Lever, Modulator Unit, Lockup Valves and Solenoid Control Valve – Overhaul Front End Overhaul Complete Overhaul Component Overhaul

Related Content:

MERCEDES BENZ KE JETRONIC FUEL SYSTEM TROUBLE TRACER, ford 550 backhoe operator manual, procedure for overhauling a gear pump, dpa injector pump govenor spring settings, ford 555c alternator wiring diagram, Lucas feul injector pump type 908 for tractor, how to repair fuel injectors on 2003 GMC Envoy, n14 cummins troubleshooting, j-38791 moore, mack 2001 fuel system

Ford SVT Contour/ Mercury 2.5L V-6 Cougar (5 Speed Manual Transmission Only) Supercharger System Installation Manual

0

Filed Under (Ford Manuals) by admin on 24-05-2012

download
1998-2000 FORD SVT CONTOUR/ MERCURY 2.5L V-6 COUGAR Installation Instructions For best performance and continued durability, please take note of the following key points: 1. Use only premium grade fuel 92 octane or higher (R+M/2). 2. The engine must have stock compression ratio. 3. If the engine has been modified in any way, check with Vortech prior to using this product. 4. Always listen for any sign of detonation (pinging) and discontinue hard use (no boost) until problem is resolved. 5. Perform an oil and filter change upon completion of this installation and prior to test driving your vehicle. Thereafter, always use a high grade SF rated engine oil or a high quality synthetic, and change the oil and filter every 3,000 miles or less. Never attempt to extend the oil change interval beyond 3,000 miles, regardless of oil manufacturer’s claims as potential damage to the supercharger may result. 6. Before beginning installation, replace all spark plugs that are older than 1 year or 10,000 miles with original heat range plugs as specified by the manufacturer and reset timing to factory specifications (follow the procedures indicated within the factory repair manual and/or as indicated on the factory underhood emissions tag). Do not use platinum spark plugs unless they are original equipment. Change spark plugs at least every 20,000 miles and spark plug wires at least every 50,000 miles. TOOL & SUPPLY REQUIREMENTS: •Factory Repair Manual •3/8″ Socket and Drive Set: SAE & Metric •1/2″ Socket and Drive Set: SAE & Metric •3/8″ NPT Tap and Handle •Adjustable Wrench •Open End Wrenches: 3/8″, 7/16″, 1/2″, 9/16″ •Center Punch •Ford Springlock 3/8″ Fuel Fitting Disconnect Tool •5 Quarts SH/CF Rated Quality Engine Oil •Oil Filter and Wrench •Flat #2 Screwdriver •Phillips #2 Screwdriver •Heavy Grease •Silicone Sealer •Drill Motor •1/8″, 3/16″, 27/64″ Drill Bits •9/16″ Rota Broach Tool (also available from Vortech) •Molylube •Wire Strippers and Crimpers •Utility Knife If your vehicle has in excess of 10,000 miles since its last spark plug change, then you will also need: •Spark Plug Socket •NEW Spark Plugs

Related Content:

free repair manual for 1998 Ford Contour SVT, repair manual for 1998 Ford Contour SVT, 97 Ford Thunderbird Repair Manual, 98 contour svt 2 5 alternator diagram, downloadable owners manual 1998 ford contour, Ford five hundred spark plug change, how to change thermostat on a 1998 ford contour, ou change the antifreeze in a 2008 G6 3 9, wheelbearing keeps wearing out 98 Camry

1998-2000 ISUZU RODEO/AMIGO HIGH/ERRATIC IDLE CONDITION SERVICE MANUAL

0

Filed Under (Isuzu Manuals) by admin on 13-05-2012

download
1998 – 2000 MODELS 1. Inspect main ground points (refer to SB99*04*S001 for more information). * P6 ground point-body [on the passenger side of engine compartment, between the battery and cruise control actuator (if equipped)]. (Figure Fig. 1 ) * P10 ground point-engine (at the alternator bracket) . (Figure Fig. 2 ) Isuzu: 1998 – 2000 Rodeo AFFECTED VEHICLES:1998 – 2000 Rodeo (UE)/Amigo (UA) models with 3.2L V6 engines NOTE: Please refer to the appropriate workshop manual for the correct diagnosing procedure and/or follow the service procedures outlined in this bulletin for the vehicle being serviced. NOTE: The 1998, 1999 or 2000 Rodeo/Amigo Electrical Troubleshooting Manual can assist in locating the vehicle ground distribution (i.e., ground contact points). * Perform a voltage drop test at the main ground points. * If the voltage drop test fails, then inspect and clean both the bolt and contact point. * Verify and correct idle settings (if needed) as described in the workshop manual. * If the repair procedure on this step solves the high idle condition, then return the vehicle to the customer. If the repair procedure on this step does not solve the high idle condition, then go to step 2 (16 pin Blue Connector). B. Remove P-6/P-10 ground terminal and bolt for ground contact inspection. * Inspect ground contact area for corrosion. * Inspect bolt and thread for damage or corrosion. * Clean the ground area and fastening bolt thoroughly with a wire brush. * Replace bolt if damaged or heavily corroded. C. Install the P-6/P-10 ground terminal and bolt (tighten using hand tools only). * Torque the P-6/P-10 ground terminal bolt to (14 N.m) 10 lb.ft. 1998 – 1999 MODELS ONLY 2. Inspect the 16 pin blue connector, located under the power steering fluid reservoir for corrosion, bent, or damaged pins (specifically for the Throttle Position Sensor). (Figure Fig. 3 )

Related Content:

disassemble engines xj8 jaguar, 1998 Chrysler Concorde Manual free, isuzu trooper grounding strap, 2000 Isuzu Rodeo Repair, 1998 jaguar fuse location, grounding points on 99 windstar, unable to tighten side post battery cable on 1998 chevy z71, volvo s70 t5 wiring pdf, ford expedition torque converter, downloadable iszuzu rodeo 1997 owners manual

2001 Ford Escort ZX2 Engine, Cooling and Exhaust Engine Timing Belt Service and Repair Manual

0

Filed Under (Ford Manuals) by admin on 15-03-2011

download
Timing Drive Components-Timing Belt Removal NOTE: Ford does not provide camshaft gear timing marks, or information to perform timing belt service without the special tools shown in this procedure. 1. Grasp the spark plug boot firmly and with a twisting pulling motion, disconnect the spark plug wires from the spark plugs. 2. NOTE: If an original spark plug is reused, install it in the cylinder from which it was removed. New spark plugs can be used in any cylinder. NOTE: Use compressed air to remove any foreign material from the spark plug well before removing the spark plugs. Remove the spark plugs . 3. Remove the valve cover. 4. Disconnect the heated oxygen sensor (HO2S) electrical connector. 5. Remove the timing belt covers. 6. Remove the catalytic converter 7. NOTE: Cylinder No. 1 is at top dead center (TDC) when the keyway is in the 12 o’clock position. Position cylinder No. 1 just prior to TDC. 8. Remove the stud bolt. 9. Install the timing peg. 10. Rotate the crankshaft clockwise against the timing peg. 11. CAUTION: If the crankshaft timing belt is to be reused, mark the direction of the camshaft timing belt to the rotation of the camshaft prior to removal, or premature wear or failure may occur. Relieve the tension on the timing belt tensioner pulley.

Related Content:

2001 zx2 transaxle tear down

1997 Mercedes Benz SL 500 Hydraulic Cylinder For Soft Top Bow Removal And Installation Manual

0

Filed Under (Mercedes-benz Manuals) by admin on 14-07-2012

download
NOTE: It is necessary to plug the hydraulic lines immediately with plugs 129 589 91 07 and the connections with plugs 129 589 00 91 11. Hydraulic cylinder remove on main bracket from inside of vehicle and lay down in soft top compartment (fig. 8) Hydraulic lines on hydraulic cylinder remove (fig. 8) NOTE: Plug the hydraulic lines immediately with plugs 129 589 00 91 07, the connections on the distributors and hydraulic cylinders with plugs 129 589 00 91 11. Screws screw out (fig. 8, item 8) and remove limit switch (item 9) from hydraulic cylinder NOTE: Check limit switches after completing vehicle and adjust, if required. Reinstall in opposite order (observe installation note) Check for proper function and leakage Special too Installation note When installing the hydraulic cylinder pay attention to the code numbers on hydraulic lines as well as the position of the lines in the B-pillar. Line positioning and code numbers Removal & Installation of Hydraulic Cylinder For Top Actuation Notes Removal & Installation of Hydraulic Cylinder For Top Actuation Preliminary jobs: Remove coupe roof (operating instructions). Remove baggage shelf. See: Interior Moulding / TrimService and Repair Remove coverings in rear. Remove occasional seats. See: SeatsService and Repair

Related Content:

Yanmar 336D hydraulic syseem, new holland ts110 hydraulic system, installing buick enclave cross bars, ford 555c hydraulic fittings, crownline boat ignition repair, 2011 aveo spark plug change, 2004sl500 mercedes benz road bar hydraulic line, filling ford 655 backhoe with hydraulic fluid for steering, mitsubishi tool # MD998769, 2003 lincoln ls 5r55s hydraulic flow chart ON YOU TUBE

Toyota Hilux, Toyota Fortuner 2.5L And 3.0L Unichip PnP Installation Instructions

0

Filed Under (Toyota Manuals) by admin on 07-11-2011

download
1. Disconnect the truck’s battery. Using a 10mm wrench, disconnect the truck’s battery at the negative terminal in the engine compartment . 2. Expose the ECU behind the passenger’s side glove compartment. i. (Photo 1) Fully o pen the glove box. ii. Gently push in on both sides of the glove box to release the stops located on the rear edge; pull the glove box toward the rear of the truck to release it from the pivot clips. 3. Install the PnP Harness i. (Photo 2) Locate the OEM ECU mounted vertically in the center of the opening. ii. Disconnect the OEM plugs from the ECU. Note: Each ECU connector has a small release tab which must be depressed to remove the plug. DO NOT FORCE THE PLUGS; if a plug is difficult to remove, try pushing it in and then pulling it back out while depressing the release tab. iii. Remove the protective plastic from one side of the long kit supplied Velcro strip and apply it to the smaller flat side of the PnP harness (same side as the looms). iv. (Photo 3) Remove the other protective plastic strip from the Velcro on the PnP harness and position the PnP case between the OEM ECU and the heater blower motor with the flat side against the blower motor; firmly press the Velcro against the OEM ECU to secure it in place. Photo 1 Clips Photo 2 PnP Harness Photo 3
v. (Photo 4) Plug all four PnP Plugs into the corresponding OEM ECU connectors. Each plug is keyed to only fit into the correct connector and which should audibly “click” when inserted correctly – both into the ECU and PnP harness. vi. Plug all four OEM plugs into the corresponding PnP Connectors. Each plug is keyed to only fit into the correct connector and which should audibly “click” when inserted correctly – both into the ECU and PnP harness. 4. Install the Unichip Computer i. Attach the remaining kit supplied Velcro strip to the back side of the Unichip Computer. ii. Remove the remaining protective plastic from the Velcro on the back of the Unichip Computer. iii. (Photo 5) Position the Unichip Computer against the bulkhead at the side of the glove box opening and press it firmly in place. iv. Plug the PnP loom’s 18-pin Molex Plug labeled Unichip into the Unichip Computer’s connector

Related Content:

unichip installation instructions, unichip manual pdf

1995 Isuzu Trooper LS TIMING BELT REMOVAL AND INSTALLATION MANUAL

0

Filed Under (Isuzu Manuals) by admin on 13-05-2012

download
TIMING BELT Removal 1. Disconnect negative battery cable. Remove air cleaner assembly. Remove upper fan shroud. Remove cooling fan assembly. Remove all accessory drive belts. 2. Remove fan pulley assembly. Remove crankshaft pulley bolt. Using Puller (J-8614-01) or equivalent, remove crankshaft pulley. Remove oil cooler hose from timing cover. Remove timing belt cover. Align all timing marks prior to belt removal. See Fig. 1 – Fig. 4 . Remove belt tensioner pusher and timing belt. Fig. 1: Aligning Timing Belt Sprockets (DOHC) Courtesy of ISUZU MOTOR CO. Installation 1. Ensure all timing marks are aligned. Install belt over one pulley at a time starting at crankshaft sprocket and working counterclockwise. Belt should go over tensioner last. Secure belt at each pulley during installation with pinch clips. See Fig. 5 . 2. Compress timing belt tensioner pusher and insert pin to retain pusher. Apply pressure to tensioner against belt, and install tensioner pusher. Tighten bolts to specification. See TORQUE SPECIFICATIONS . 3. Loosen tensioner pulley bolt. Apply pressure on belt by rotating tensioner. Tighten tensioner pulley bolt to specification.. See TORQUE SPECIFICATIONS . Remove pin from timing belt tensioner pusher. 4. Remove pinch clips from timing belt (if used). Install crankshaft pulley, tightening center bolt finger tight. Rotate crankshaft 2 turns clockwise. Ensure timing belt tensioner pusher rod protrudes proper

Related Content:

isuzu 4hk1 timing marks, 2004 Isuzu NPR refrigerant