tundra engine block heater installation

You search PDF repair manual about tundra engine block heater installation, if there are search results will appear below. If search results do not exist, please search by others keyword.



  tundra engine block heater installation Direct Download speed 5432 Kb/s

  tundra engine block heater installation Full Version speed 8172 Kb/s



2001 Ford Taurus/ Sable Cooling System Draining Filling and Bleeding Workshop Manual

0

Filed Under (Ford Manuals) by admin on 19-02-2011

download
CAUTION: Vehicle cooling systems are filled with Motorcraft Premium Engine Coolant VC-4-A (in Oregon VC-5, in Canada CXC-10) or an equivalent meeting Ford specification ESE-M97B44-A. NOTE: Less than 80% of the coolant capacity can be recovered with the engine in the vehicle. Dirty, rusty or contaminated coolant requires replacement. 1. Release the pressure in the cooling system by slowly turning the pressure relief cap one half to one turn counterclockwise to the first stop on the filler neck. When the pressure has been released, remove the pressure relief cap. 2. Raise and support the vehicle. For additional information, refer to Section 100-02 . 3. Remove the front splash shield. 4. Place a suitable container below the radiator draincock. Drain the coolant. 5. Close the radiator draincock when finished. Filling and Bleeding With RADKITPLUS 1. Using the special tool, install the RADKITPLUS and follow the RADKITPLUS manufacturer’s instructions to fill and bleed the cooling system. Filling Without RADKITPLUS CAUTION: Engine coolant provides freeze protection, boil protection, cooling efficiency and corrosion protection to the engine and cooling components. In order to obtain these protections, the engine coolant must be maintained at the correct concentration and fluid level. When adding engine coolant, use a 50/50 mixture of engine coolant and clean, drinkable water. To maintain the integrity of the coolant and the cooling system: * Add Motorcraft Premium Engine Coolant VC-4-A (in Oregon VC-5, in Canada CXC-10) or equivalent meeting Ford specification ESE-M97B44-A. * Do not add Motorcraft Specialty Engine Coolant VC-2 or an equivalent meeting Ford specification WSS-M97B44-D. Mixing coolants may degrade the coolant’s corrosion protection. * Do not add alcohol, methanol, brine or any engine coolants mixed with alcohol or methanol antifreeze. These can cause engine damage from overheating or freezing. * Do not mix with recycled coolant unless it meets the requirement of specification ESE-M97B44-A. Not all coolant recycling processes meet this specification. Use of such a coolant may harm the engine and cooling system components. 1. Install the front splash shield. 2. Lower the vehicle. 3. Fill the degas bottle with the correct engine coolant mixture. 4. Install the pressure relief cap. 5. Move the temperature blend selector to the full warm position. 6. WARNING: Do not stand in line with or near the engine cooling fan blade when revving the engine. Run the engine until it reaches operating temperature. 7. Add the correct coolant mixture to the degas bottle until the coolant level is between the COOLANT FILL LEVEL marks. 8. Turn off the engine and allow the cooling system to cool. Recheck the coolant level and fill the cooling system to the FULL mark on the degas bottle. 9. WARNING: Do not stand in line with or near the engine cooling fan blade when revving the engine. Repeat Steps 3 through 8 until the reservoir level is OK. Bleeding Without RADKITPLUS 1. Bleed the cooling system as follows: * Select the maximum heater temperature and blower motor speed settings. Position the control to discharge air from the A/C vents in the instrument panel. * WARNING: Do not stand in line with or near the engine cooling fan blade when revving the engine. Start the engine and allow it to idle. While the engine is idling, feel for hot air from the A/C vents. * CAUTION: If the air discharge remains cool and the engine coolant temperature gauge does not move, the engine coolant level is low in the engine and must be filled. Stop the engine, allow it to cool and fill the cooling system. Start the engine and allow it to idle until the normal operating temperature is reached. Hot air should discharge from the A/C vents. The engine coolant temperature gauge should maintain a stabilized reading in the middle of the NORMAL range and the upper radiator hose should feel hot to the touch. * Shut the engine off and allow it to cool. * Check the engine for coolant leaks. * Check the engine coolant level in the degas bottle and fill it as necessary.

Related Content:

4D35 engine repair manual, so5d engine repair manual, 2000 Nissan sentra 1 8 engine bolt torque diagram, 6m70 wiring diagram, what causes damage to a flywheel on a 2004 yukon, so5d engine, SO5D OBD ll Code, TOYOTA SO5D SERVICE MUNAL, 2005 chevy impala motor diagram, perodua engine overhall pdf

TOYOTA AND LEXUS HIGHLANDER HYBRID REMOVAL AND INSTALLATION MANUAL

0

Filed Under (Toyota Manuals) by admin on 08-03-2012

download
Engine and Vehicle Identification Chart………………………………………..4-2 General Engine Specifications………4-2 Engine Tune-Up Specifications……..4-2 Capacities ………………………………….4-3 Valve Specifications …………………….4-3 Crankshaft and Connecting Rod Specifications……………………..4-3 Camshaft and Bearing Specifications ……………………………4-4 Piston and Ring Specifications……..4-4 Torque Specifications………………….4-4 Wheel Alignment ………………………..4-5 Tire, Wheel and Ball Joint Specifications ……………………………4-5 Brake Specifications ……………………4-5 Scheduled Maintenance Intervals……………………………………4-6 STEERING AND SUSPENSION ………………4-28 A Air Bag…………………………………….4-28 Disarming ……………………………4-28 Precautions ………………………….4-28 Alternator …………………………………..4-7 B Brake Caliper ……………………………4-30 Removal And Installation……….4-30 C Camshaft and Valve Lifters…………4-14 Inspection ……………………………4-16 Removal & Installation…………..4-14 CV-Joints………………………………… 4-24 Overhaul ……………………………..4-24 Cylinder Head …………………………..4-10 Removal & Installation…………..4-10 D Disc Brake Pads………………………..4-32 Removal And Installation……….4-32 E Engine Assembly ………………………..4-7 Removal & Installation…………….4-7 Exhaust Manifold ………………………4-12 Removal & Installation…………..4-12 F Front Crankshaft Seal………………..4-14 Removal & Installation…………..4-14 Front Halfshaft………………………….4-23 Removal & Installation…………..4-23 Front Strut ……………………………….4-28 Removal & Installation…………..4-28 Front Wheel Bearing………………….4-29 Fuel Filter ………………………………..4-21 Fuel Injector……………………………..4-22 Removal & Installation…………..4-22 Fuel Pump ……………………………….4-21 Removal & Installation…………..4-21 Fuel System Pressure………………..4-21 Relieving ……………………………..4-21 H Heater Core………………………………..4-7 Removal & Installation…………….4-7 Hybrid Transaxle Assembly…………4-22 Removal & Installation…………..4-22 I Ignition Timing ………………………….. 4-7 Adjustment…………………………….4-7 Intake Manifold …………………………4-11 Removal & Installation…………..4-11 L Lower Ball Joint………………………..4-29 Removal & Installation…………..4-29 Lower Control Arm……………………4-29 Removal & Installation…………..4-29 O Oil Pan…………………………………….4-18 Removal & Installation…………..4-18 Oil Pump …………………………………4-18 Removal & Installation…………..4-18 P Pinion Seal ………………………………4-27 Removal & Installation…………..4-27 Piston and Ring………………………..4-21 Positioning ………………………….4-21 Power Rack And Pinion Steering Gear…………………………..4-28 Removal & Installation…………..4-28 R Rear Halfshaft………………………….. 4-24 Removal And Installation……….4-24 Rear Main Seal…………………………4-19 Removal & Installation…………..4-19 Rear Strut…………………………………4-28 Conventional Strut Overhaul…..4-28 Removal And Installation……….4-28 Rear Traction Motor…………………..4-22 Removal & Installation…………..4-22 Rear Wheel Bearing…………………..4-29 Removal And Installation……….4-29 T Timing Belt ………………………………4-19 Removal & Installation…………..4-19 V Valve Lash ……………………………….4-17 Adjustment…………………………..4-17 W Water Pump ……………………………..4-10 Removal & Installation………..

Related Content:

how to install running boards on honda pilot, nissan ka20 16 valve cyl head gasket replacement, 2001 chevrolet monte carlo radiator removal, zx2 vct replacement instructions, 2006 sienna liftgate struts replacement video, 2002 highlander brake torque, nissan ka20 timing marks, replace alternator on honda ridgeline, quicksilver isolators pdf, whats the piece that connects to lower control arm on 1997 Buick le sabre

1999 Saturn SL1 L4-1.9L SOHC VIN 8 Engine – Driveability Concerns/ Cooling System DTC’s Set

0

Filed Under (Saturn Manuals) by admin on 19-05-2012

download
1. Disconnect engine coolant temperature sensor electrical connector and inspect sensor and connector terminals for corrosion and/or evidence of engine coolant. ^If terminals are corroded or if there is evidence of engine coolant proceed to step 4. ^If terminals are not corroded and there is no evidence of engine coolant, reconnect the electrical connector and continue to next step. 2. Perform one or both of the following checks to determine whether the engine coolant temperature sensor is providing the correct temperature indication. If engine coolant temperature sensor reading does not pass either of the above tests, continue with next step. ^If engine is at ambient temperature (vehicle has been sitting overnight or not started for several hours), use a Scan tool to compare the inlet air temperature ( IAT ) to the engine coolant temperature ( ECT ). These two readings should be within 2°C (4°F) of each other. ^If engine is at operating temperature, install a thermometer in the coolant recovery reservoir. With the engine running and A/C off, use a Scan tool to compare the engine coolant temperature sensor reading to the thermometer reading. These two readings should be within 8°C (15°F) of each other If engine coolant temperature sensor reading passes both of the tests above, refer to appropriate symptom diagnostic chart in the Engine/Emissions Controls Section of applicable Engine Service Manual. 3. Turn ignition off. 4Remove coolant surge tank cap. 5. Drain at least 1.9 L (2 Qt.) of engine coolant from the cooling system by opening radiator drain valve or removing engine drain plug. Collect engine coolant in a container. 6. Disconnect engine coolant temperature sensor electrical connector. 7. Remove engine coolant temperature sensor from cylinder head. 8. Obtain replacement engine coolant temperature sensor (P/N 21025106). 9. Use appropriate tap to clean sensor mounting hole of any thread sealant residue. 10. Install engine coolant temperature sensor in cylinder head. Torque: Engine Coolant Temperature Sensor: 8 Nm (71 in-lbs) 11. Inspect harness connector terminals for corrosion and/or evidence of engine coolant. If harness connector terminals are corroded or there is evidence of engine coolant, the harness connector must be replaced with new connector (P/N 12117087-includes: connector, terminals, wires, and splice sleeves). 12. Connect engine coolant temperature sensor connector. 13. Transfer engine coolant drained in step 5 into coolant surge tank. If necessary fill coolant surge tank to the FULL COLD range with 50/50 solution of correct type of antifreeze and clean water. 14. Start engine and check for leaks. 15. Run engine until upper radiator hose is hot, then add additional coolant if needed to bring the level to the FULL COLD level (1991-early 1997) or within the Min./Max. cold range (late l997-2001). 16. Install coolant surge tank cap.

Related Content:

yhs-sgm_fb, wiring diagram for 2005 kia sedona engine cooling fan temperature sensor, bye pass c15 timming sensor, replacing s radiator 2001 silhouette oldsmobile, crank sensor location on 6 7 power stroke, 2001 oldsmobile intrique coolant system diagram, location of air temp sensor on 2001 toyota celica, 2001 mitsubishi montero limited head gasket repair procedure pdf download, how to drain radiator on 2007 ford fusion 2 3 L, hino j500 pump timing marks

1998 Chevrolet Blazer Engine Oil Cooler Hose/ Pipe Removal And Installation Manual

0

Filed Under (Chevrolet Manuals) by admin on 22-05-2012

download
Removal Procedure 1. Remove the steering linkage shield. Refer to Steering Linkage Shield Replacement in Steering Linkage. Important: Have a drain pan ready for the engine oil to drain into. 2. Remove the bolt attaching the engine oil cooler lines to the remote (frame mounted) oil filter adapter. 3. Remove and discard the seals. 4. Remove the engine oil cooler line retaining rings from the engine oil cooler line quick connectors at the radiator engine oil cooler inlet and outlet. Follow the next two steps for the proper retaining ring removal procedure. 5. Using a bent-tip screwdriver or equivalent, pull on one of the open ends of the retaining ring in order to rotate the retaining ring. 6. Rotate the retaining ring around the quick connector until the retaining ring is out of position and can be completely removed. Discard the retaining rings. 7. Remove the engine oil cooler lines from the quick connectors at the radiator engine oil cooler inlet and outlet. Pull the lines straight out from the connectors. 8. Remove the remote engine oil filter lines support clamp bolt. Important: Have a drain pan ready for the engine oil to drain into. 9. Remove the bolt attaching the remote engine oil filter lines to the remote (frame mounted) engine oil filter adapter. 10. Hold the remote engine oil filter lines below the remote engine oil filter lines (engine mounted) adapter to drain the engine oil. 11. Remove and discard the seals. 12. Remove the bolt attaching the remote engine oil filter lines to the remote engine oil filter lines (engine mounted) adapter. 13. Remove and discard the seals. 14. Clean all of the components in a suitable solvent, and dry them with compressed air. 15. Inspect the fittings, the connectors, the cooler lines, the cooler, the filter lines, and the remote filter adapter for damage, distortion, or restriction. Replace parts as necessary. 16. Flush the engine oil cooler, the engine oil cooler lines, the remote engine oil filter adapter, and the remote engine oil filter lines with the same type of engine oil normally circulating through the engine. Installation Procedure

Related Content:

replace oil cooker 3406 cat motor, 2006 impala oil filter housing gasket, 2006 chevy trailblazer engine removal, removing the oil pan on a 2008 impala 3 5, oil cooler on 3406 cat how to change, 2001 a4 oil cooler lines, 2012 kia srento a/c condensor drain line drawing, how to install oil filter adapter gasket 2007 montana, 2005 ford escape 2 3liter oil dipstick housing seal, how many man hours to replace engine suburban 2007 for

EDELBROCK ENGINE MOUNT ADAPTER PLATES For Converting Small Block Chevy Applications to LS1 INSTALLATION INSTRUCTIONS

0

Filed Under (Chevy Manuals) by admin on 27-12-2011

download
PRE-INSTALLATION PROCEDURE General Motors vehicles came with many different engine and transmission combinations. This section is intended to verify that all the correct components are in place prior to installation. If the vehicle is currently equipped with a small block Chevrolet V8, then the engine isolator for the current application will work with the Edelbrock Adaptor plates. See the next page for further notes on various applications. A-BODY APPLICATIONS: 1964 – 1967: Vehicles that are being converted from six cylinder or a non-Chevrolet engine can use engine frame stands for the 283 to 327 from a salvage yard or reproduction suppliers such as OPGI and Yearone; engine isolators can be of the OEM rubber type from a parts supplier or polyurethane safety mounts from Energy Suspension: part #3.1114 (zinc plated), or #3.1115 (chrome). 1964 – 1967 applications will require mildly slotting the engine frame stand mounting holes, as shown in Figures 1 and 2. FIGURE 1 FIGURE 2 – 1968 – 1972: From 1968 to 1972, Chevrolet used two different frame stands with matching engine isolators. Type one is the 307 (and some early 1968 327′s), while type two includes all engines from the later 1968 327′s through to the 454, encompassing all engine sizes in-between. If you have obtained frame stands from another vehicle, use the following procedure to identify your mount system: measure the ears of the engine isolator where the engine mounting bolt goes, the inside dimension is 2 5/8″for the 307 cid (Figure 3) and 2 3/8″for the larger sized engine (Figure 4). Frame stands for the late 327,350 to 454 are also available from reproduction suppliers such as OPGI and Yearone, engine isolators can be of the OEM rubber type from a parts supplier or polyurethane safety mounts from Energy Suspension: part #3.1114 (zinc plated) #3.1115 (chrome) for the 307, part #3.1117 (zinc plated) or #3.1118 (chrome) for the late 327 to the 454. FIGURE 3 (307) FIGURE 4 (350 et al) F-BODY AND X-BODY APPLICATIONS: 1967 – 1969 F-body and 1968 – 1974 X-body: Vehicles that are being converted from six cylinder or a non-Chevrolet engine will require engine isolators that match the engine frame stand. There are a variety of styles depending on engine size and model year, so get the engine isolators and frame stands which are available from reproduction suppliers such as Classic Industries and Yearone. Engine isolators can be of the OEM rubber type from a parts supplier or polyurethane safety mounts from Energy Suspension. There are two basic types of engine isolators; to identify them measure the distance between the tab for the engine mount through bolt, if it is 2-5/8″use Energy Suspension #3.1114 (zinc plated) #3.1115 (chrome), if the distance is 2-3/8″use #3.1117 (zinc plated) #3.1118 (chrome).

Related Content:

what does the s stand for in jaguar s type

2001 Dodge Durango BLOWER MOTOR RELAYS REPAIR MANUAL

0

Filed Under (Dodge Manuals) by admin on 13-02-2012

download
BLOWER MOTOR RESISTOR 1. Disconnect negative battery cable. Disconnect blower motor resistor harness connector. Using DVOM, check for continuity between all blower motor resistor terminals. If continuity exists between all terminals, go to next step. If continuity does not exist between all terminals, replace faulty blower motor resistor. 2. Check for open or short in circuits between blower motor resistor and heater control panel. Also check for open or short in wire between blower motor resistor and blower motor. BLOWER MOTOR SWITCH 2000 Dakota, 2000 Durango & 2000-01 Ram Pickup 1. Remove Power Distribution Center (PDC) cover. Using DVOM, check for battery voltage at PDC fuse No. 5 (40-amp) on Dakota and Durango; PDC fuse No. 12 (40-amp) on Ram Pickup. If battery voltage exists, go to next step. If battery voltage does not exist, check for open in Red wire between battery and underhood PDC. If Red wire is okay, replace underhood PDC. 2. Disconnect negative battery cable. Remove heater control panel. See HEATER CONTROL PANEL under REMOVAL & INSTALLATION. Disconnect heater control panel cable, electrical and vacuum connectors as necessary. Using DVOM, check for continuity between heater control panel harness connector terminal No. 7 (Black wire on Dakota and Durango; Black/Orange on Ram Pickup) and ground. See Fig. 5 . If continuity exists, go to step 4 . 3. If continuity does not exist, repair open in Black wire or Black/Orange wire between heater control panel 2001 Dodge Durango 2000-01 HEATER SYSTEMS’ ‘RWD Trucks & Vans harness connector terminal No. 7 and ground connector located at lower right corner of instrument panel (Dakota and Durango) or behind center of instrument panel (Ram Pickup). 4. Place heater mode control knob to any position except OFF. Using DVOM, check for continuity between heater control panel terminal No. 7 and terminals No. 3, 4, 5 and 6 while rotating blower motor switch. See Fig. 5 . 5. If continuity does not exist at any terminal, replace faulty heater control panel. If continuity exists as specified, check for open in circuits between heater control panel and blower motor resistor. Also check for an open in circuit between heater control panel and blower motor. See WIRING DIAGRAMS . Fig. 5: Identifying Heater Control Panel Blower Switch Connector Terminals (2000 Dakota & Durango Are Shown; Ram Pickup Is Similar) Courtesy of CHRYSLER CORP. Ram Van/Wagon 1. Disconnect negative battery cable. Remove heater control panel. See HEATER CONTROL PANEL under REMOVAL & INSTALLATION. Disconnect heater control panel harness connectors. Using DVOM, check for continuity between heater control panel C3 harness connector terminal “C” (Black wire) and ground. See Fig. 6 . If continuity exists, go to next step. If continuity does not exist, repair open in Black wire between heater control panel and ground connector located at lower right of steering column. 2. Place heater mode control selector to any position, except OFF. Using DVOM, check for continuity between appropriate terminals of heater control panel, for C3 connector terminals “B” (Violet wire) and “C” (Black wire). If continuity exists through heater control panel, go to next step. If continuity does not exist, replace faulty heater control panel assembly. 3. Using DVOM, check for continuity between heater control panel C3 connector terminal “B” (Violet wire) and C1 connector terminal “E” (Violet wire). See Fig. 6 . If continuity exists, go to next step. If continuity does not exist, repair open in Violet wire between heater control panel C3 and C1 connectors.

Related Content:

where is the blower fuse on a 2001 chevy s10, where is the blower motor resistor located on a 2003 monte carlo, 2010 f150heater fan speed issues, location of mode motor for 99 honda civic lx, Body Control Module 2007 Silverado, fuse for rear control panel 2006 durango, 2008 colbalt heater core removal, 2001 DODGE RAM 2500 OWNERS MANUAL, repair manual for heater plenum 2011 f-150, 98 taurus heater hose diagram

TOYOTA BLOCK HEATER APPLICATION INSTALLATION INSTRUCTIONS

0

Filed Under (Toyota Manuals) by admin on 20-06-2011

download
Remove oxygen sensor wire connector & clamp. Remove exhaust manifold & drain coolant. Remove installation hole cover & 2 studs. Remove original silicone sealant from hole. Clean hole surfaces. Secure heater in position with the bracket, bolts & lock washers provided. Connect cordset. Route cordset through opening between right side of bumper & engine under-cover. For Avalon, route cordset through opening beside right side of radiator and under right headlight. Secure cordset to the A/C suction pipe. Replace engine components removed earlier. Refill coolant, run engine & check for leakage & coolant level. 3 AVALON 2005- 2010 2GR-FE PU140-00900 PU140- 03571 Rear, L.H.S. (hole direction pointing to front) Route cord up. Tie the cord to the lower heater hose outlet. Route the cord to left side of engine. Tie the cord to the main harness besides the fuse box. Remove front radiator plastic cover. Route the cord down on left side of battery and tie the cord to the left side of radiator coolant fan harness at the front bottom of the battery. Route the cord to the front and tie to the front grille. 11 1983- 86 2SE C0140-00123* C0140- 00069 Front L.H.S. 2nd from transmission 6 1987- 91 3S-FE C0140-00134* C0140- 00070 Rear 2nd from right 12 1988- 91 2V-ZFE C0140-00110* C0140- 00767 Front centre. Loosen union bolt of water outlet five revolutions before refilling coolant. Tighten after coolant fill. 12 1992- 93 3VZ-FE C0140-01141* C0140- 00903 Front 1st from left. Remove exhaust manifold; remove exhaust pipe if necessary. Route cordset towards the left side of engine compartment. 6 1992- 2001 5S-FE C0140-01123* C0140- 02899 Front, 2nd from left. Remove exhaust manifold. For models prior to 1994 model year, remove upper exhaust manifold heat shield only. Route cordset towards left side of engine compartment. 12 CAMRY 1994- 2006 IMZ-FE C0140-00644* C0140- 02897 Front, R.H.S. Remove oxygen sensor wire connector & clamp. Remove exhaust manifold & drain coolant. Remove installation hole cover & 2 studs. Remove original silicone sealant from hole. Clean hole surfaces. Secure heater in position with the bracket, bolts & lock washers provided. Connect cordset. Route cordset through opening between right side of bumper & engine under-cover. For Avalon, route cordset through opening beside right side of radiator and under right headlight. Secure cordset to the A/C suction pipe. Replace engine components removed earlier. Refill coolant, run engine & check for leakage & coolant level

Related Content:

2005 hole is hose toyota camry, 2008 camry how to eemove enine, 2gr-fe manual

2000 Audi A6 OIL PAN (A4 And A6) Removal And Installation Manual

0

Filed Under (Audi Manuals) by admin on 01-07-2012

download
OIL PAN(A4 & A6) Removal (Lower Pan- A4 & A6) 1. Disconnect negative battery cable. 2. Remove engine noise insulator (undercover). See Fig. 12 . Drain engine oil. 3. Unbolt left and right swaybar stabilizer bracket bolts (4) from mounting bracket. See Fig. 98 . Lower swaybar stabilizer not more than 10cm (3.94 INCHES) and secure with heavy wire. 4. If vehicle is equipped with automatic transmission, unbolt oil cooler pipe (line) bracket from right side oil pan. 5. Remove lower oil pan. To install oil pan (lower), see INSTALLATION (LOWER OIL PAN- A4 & A6) . Installation (Lower Oil Pan- A4 & A6) 1. Ensure oil pan surfaces are clean and dry. Remove residual sealant from oil pan, if necessary, with hand drill and plastic brush instead of a flat scrapper. See Fig. 99 . Install gasket. 2. Install 2 bolts diagonal to each other (to hold up pan). Install the rest of the bolts and hand tighten. 3. Starting at center and moving outward, tighten lower oil pan to upper oil pan bolts to 10 N.m (89 INCH lbs.). Tighten oil pan drain plug 30 N.m (22 ft. lbs.). Wait 30 minutes before filling with engine oil. Tighten all bolts to specification. See TORQUE SPECIFICATIONS . 4. To complete installation, reverse removal procedure. Fill and bleed cooling system. See COOLING SYSTEM BLEEDING . Removal (Upper Oil Pan- A4 & A6) 1. Disconnect negative battery cable. Remove oil dipstick. Unbolt oil dipstick tube at front of cylinder head. Remove oil dipstick tube. 2. Remove engine noise insulator (undercover). See Fig. 12 . Drain engine oil. 3. Move lock carrier into service position. See LOCK CARRIER . This will allow servicing of front engine components and facilitate removal of oil pan. 4. Open coolant expansion tank cap, drain cooling system at radiator. Open the coolant pump bearing housing drain plug. Located at bottom of block near transmission bell housing, drivers side of vehicle. See Fig. 32 – Fig. 33 . If vehicle is equipped with automatic transmission, unbolt oil cooler pipe (line) CAUTION: Wear eye protection NOTE: Obtain radio code before disconnecting battery. For help in identifying components and component locations, refer to illustrations Fig. 108 -Fig. 109 . NOTE: If engine is out of car, ensure oil pan is aligned with cylinder block on flywheel side. 2000 Audi A6 1998-02 ENGINES’ ’2.8L V6 30-Valve 2000 Audi A6 1998-02 ENGINES’ ’2.8L V6 30-Valve bracket from right side oil pan. 5. Position Engine Support (10-222A) with (10-222A/3) engine support adapter, or equivalent, on bolted flanges of fenders. Connect support bracket to front and rear engine lifting eyes. Lift up engine as far as possible. DO NOT use excessive force to raise engine. 6. Cut tie wraps and open bracket supporting starter wiring. See Fig. 97 . Disconnect electrical connection at starter.

Related Content:

04 2 7l allroad p0491 p0492, cummins isx subassembly procedure, Oil Pan Gasket Leaking 2005 altima, replacing oil pan 2000 avalon, instutins how to replce oil PAN GASKEET ON 2006 CHEV IMPLA 5 3, mack mp8 coolant pump replacement, torque specs for 2004 chevy deisel oil pan, ntc cummins pan bolts, oil drain pan torque 1991 corrola, oil drain plug for 3406e cat

1999-2006 Volkswagen A4 Engine Speed Sensor G28 Checking

0

Filed Under (Volkswagen Manuals) by admin on 31-01-2011

download
Special tools, testers and auxiliary items required Multimeter . Wiring diagram. Test requirements The Motronic Engine Control Module (ECM) J220 fuses OK. Battery voltage at least 12.5 volts. All electrical consumers such as, lights and rear window defroster, switched off. Vehicles with automatic transmission, shift selector lever into position “P” or “N” . A/C switched off. Ground (GND) connections between engine/transmission/chassis OK. Ignition switched off. Test procedure Perform a preliminary check to verify the customers complaint. Refer to Preliminary Check Start diagnosis The Engine Speed (RPM) Sensor G28 detects RPM and reference marks. Without an engine speed signal, the engine will not start. If the engine speed signal fails while the engine is running, the engine will stop immediately Function test Connect the scan tool. Switch the ignition on. Using the scan tool, check the engine speed: End diagnosis and switch ignition off. If the specified value was not obtained: Checking internal resistance Disconnect the gray Engine Speed (RPM) Sensor G28 electrical harness connector 7 arrow 7 . Using a multimeter , check the Engine Speed (RPM) Sensor G28 terminals 2 to 3 7 see insert 7 for resistance. Specified value: 0.7 to 1000 kOhm Check Engine Speed (RPM) Sensor G28 terminals 1 to 2 and 1 to 3 for short circuits. Specified value: ? (infinity) If any of the specified values are not obtained: Replace the Engine Speed (RPM) Sensor G28 . Refer to Engine Mechanical, Fuel Injection and Ignition 7 Repair Group 13 . If the specified values are obtained: Checking wiring If the manufacturers test box is being used. Perform the following step. Install the test box Adapter F/VAG1598 (68 Pin) VAG1598/22 . If the manufacturers test box is not being used. Perform the following step. Remove the Motronic Engine Control Module (ECM) J220 . Refer to Motronic Engine Control Module J220, Replacing .

Related Content:

G28 Engine Speed Sensor where to buy, g28 resistance value bvk engine, G28 Sensor VW

1993-2002 Volkswagen Golf, Jetta, GTI, Cabrio A/C controls and mechanical components service manual

0

Filed Under (Volkswagen Manuals) by admin on 09-07-2012

download
1 – . Dust and pollen filter Where applicable 2 – . Plenum cover Removing/installing – -”> 3 – Evaporator water drain valve Located behind bulkhead insulation Removing/installing Fig. 2 Removing and installing evaporator water drain valve 4 – . Heater core connections and vacuum hose guide 5 – . Fresh Air/Recirculating Flap Two-Way Valve N63 Valve open when voltage applied Vacuum hose layout Vacuum hose layout 6 – . Coolant Fan Control (FC) Control Module J293 With fuse Fuse Strip S88 (1993 m.y.) With fuses Coolant Fan Second and Third Speed Fuse S107 and Coolant Fan First Speed and A/C Clutch Fuse S108 (1994 m.y. micro ) Connector terminal identification: micro 09.93 Fig. 5 Connector terminal identification of Coolant Fan Control (FC) Control Module J293 ( 09.93) 10.93 micro Fig. 6 Connector terminal identification of Coolant Fan Control (FC) Control Module J293 (10.93 ) 7 – . Vacuum reservoir Insert vacuum hose 30 mm (1.2 in.) into reservoir Removing/installing Fig. 7 Removing and installing vacuum reservoir A/C and heating system components, engine compartment Vacuum hose Vacuum hose layout Vacuum hose layout 9 – . A/C Cut-Out Thermal Switch F163 and Third Speed Coolant Fan Control (FC) Thermal Switch F165 A/C Cut-Out Thermal Switch F163 only on vehicles with engine codes AAA, AAZ, ABA, ACC A/C Cut-Out Thermal Switch F163 switches A/C Clutch N25 off at high engine coolant temperature; OFF (switch open) above 119 degree C (246 degree F); ON (switch closed) below 112 degree C (234 degree F) Third Speed Coolant Fan Control (FC) Thermal Switch F165 only on vehicles with 3- speed coolant fan motor Third Speed Coolant Fan Control (FC) Thermal Switch F165 switches radiator coolant fan to 3rd speed as engine coolant temperature increases; 3rd speed ON (switch closed) above 112 degree C (234 degree F); OFF (switch open) below 108 degree C (226 degree F) Removing and installing (engine code AAA) Fig. 3 Removing and installing A/C Cut- Out Thermal Switch F163 and Third Speed Coolant Fan Control (FC) Thermal Switch F165 (2.8 liter VR6 engine code AAA) Removing and installing (engine code ABA) Fig. 4 Removing and installing A/C Cut- Out Thermal Switch F163 (2.0 liter engine code ABA) 10 – . Condenser* 11 – . Pressure relief valve*

Related Content:

wiring diagram for the drivers side front electric window switch on a 1998 ford contour, 02 Jetta Fan Control Module, 2002 lincoln ls cooling system diagram, fan fuse for 1995 chevy lumina, fan sensor vw beetle how to change, how to replAce mounting on evap canister on 2001 f150 to truck body, Mazda MPV Fan Control Module 2002

Related Content:

4D35 engine repair manual, so5d engine repair manual, 2000 Nissan sentra 1 8 engine bolt torque diagram, 6m70 wiring diagram, what causes damage to a flywheel on a 2004 yukon, so5d engine, SO5D OBD ll Code, TOYOTA SO5D SERVICE MUNAL, 2005 chevy impala motor diagram, perodua engine overhall pdf