vacuum hose diagrams for 2001 pt cruiser

You search PDF repair manual about vacuum hose diagrams for 2001 pt cruiser, if there are search results will appear below. If search results do not exist, please search by others keyword.



  vacuum hose diagrams for 2001 pt cruiser Direct Download speed 5432 Kb/s

  vacuum hose diagrams for 2001 pt cruiser Full Version speed 8172 Kb/s



1998-2000 HONDA Accord L4 Replace the fuel pressure regulator, and reroute the fuel pressure regulator vacuum line

0

Filed Under (Honda Manuals) by admin on 16-07-2012

download
1. Locate and identify the three vacuum ports on the intake manifold. 2. Disconnect and discard the vacuum hose that connects the fuel pressure regulator to vacuum port C. 3. Plug vacuum port C with the cap from the tube kit. 4. Replace the fuel pressure regulator. Refer to page 11-113 of the 1998-00 Accord Service Manual. 5. Install the new vacuum hose kit using one of the following procedures 1. Remove and discard the cap from vacuum port A. 2. Connect the short vacuum hose to vacuum port A M/T WITH CRUISE CONTROL 2. Disconnect and discard the vacuum hose that connects the fuel pressure regulator to vacuum port C. 3. Plug vacuum port C with the cap from the tube kit. 4. Replace the fuel pressure regulator. Refer to page 11-113 of the 1998-00 Accord Service Manual. 5. Install the new vacuum hose kit using one of the following procedures. Zoom Sized for Print 1. Remove and discard the cap from vacuum port A. 2. Connect the short vacuum hose to vacuum port A. Zoom Sized for Print 3. Anchor the long vacuum hose by attaching it to the rear intake air duct clip and to the cruise control hose. . Route the new vacuum hose to the fuel pressure regulator. Attach the hose to the three rear clips on the engine wire harness cover. Zoom Sized for Print 1. Remove and discard the vacuum hose from vacuum port A. This hose supplies vacuum to the rear engine mount control solenoid. 2. Connect the short vacuum hose from the top of the Y fitting to vacuum port A

Related Content:

1993 Corvette Service Manual PDF, vent line 1998 mercy sable, ford taurus 2001 engine vacuum hoses on intake, What color is the tcc solenoid in toyota sequoia, 2002 2 4L olds alero vacuum hose routing diagram, vacume lines on 2004 pt cruiser gt, VACUUM LINES ON A 2003 GM 6 CLINDER, is there a vacuum hose on the transmission of a ford fusion, vaccum lines 2001 pt cruiser, Does a volvo d12 engine require silicone or gasket between engine and flywheel housing

1995-1999 Buick Riviera Steering Vibration/Shudder/Moan During Parking Maneuvers on Dry Pavement (Install Power Steering Pressure (Inlet) and/or Return (Outlet) Hose Assembly)

0

Filed Under (Buick Manuals) by admin on 11-02-2012

download
1. Verify that the power steering pump reservoir is full. 2. Verify that the accessory drive belt is in good condition and that the pulleys are not bent or damaged. 3. Verify proper belt tension and operation of the belt tensioner. 4. Check for power steering hose ground out conditions. 5. Check for good engine idle and correct engine RPM. 6. Check to see that the rear transaxle mount does not have a plastic assembly aid installed which is used Subject: Steering Vibration/Shudder/Moan During Parking Maneuvers on Dry Pavement (Install Power Steering Pressure (Inlet) and/or Return (Outlet) Hose Assembly) Models: 1995-99 Buick Riviera 1997-2001 Buick Park Avenue, Ultra 2000-2001 Buick LeSabre 2000-2001 Pontiac Bonneville • 1995-98 Buick Riviera • 1997-98 Buick Park Avenue and Ultra • 1999 Buick Riviera • 1999-2001 Buick Park Avenue and Ultra • 2000-2001 Buick LeSabre • 2000-2001 Pontiac Bonneville • If fluid level is low, fill and check for leaks. • If power steering system has air in the system, perform the “Bleeding Air from Power Steering System” procedure as described in the Power Steering System sub-section of the Service Manual. Important: When performing the “Bleeding Air from Power Steering System” procedure, it is important that the front of the vehicle is supported by the lower control arms. If the vehicle is not supported by the lower control arms, the procedure may cause the strut bushing to dislocate and cause new concern. for assembly purposes. If the assembly aid is installed, remove the assembly aid and install the rear transaxle mount. 7. With the vehicle on dry pavement, maneuver the vehicle in parking positions. If the steering vibrates/shudders or moans in this test, replace the power steering pressure hose and/or the harmonic balancer. Important: A defective harmonic balancer on the 1995 Buick Riviera can influence steering vibrations after power steering hose installation. Important: When installing the pressure hose on the 1995 Buick Riviera, pull down on the pressure hose at the rear of the engine or bend the hose to allow clearance between the hose and the front of the dash. Power Steering Pressure (Inlet) Hose Replacement Procedure For 1995-1998 Vehicles: 1. Raise and suitably support the vehicle. Refer to Vehicle Lifting and Jacking in the General Information section of the Service Manual. 2. Drain the power steering fluid. Refer to Draining the Power Steering System in the Power Steering section of the Service Manual. 3. Remove the power steering gear assembly heat shield (1). 4. Disconnect the power steering pressure hose from the power steering pump assembly (4). 5. Remove the bolt/screws from the retaining clips (3). 6. Disconnect the power steering pressure hose from the power steering gear assembly (2). 7. Remove the power steering pressure hose assembly from the vehicle. 8. Install the power steering pressure hose assembly to the vehicle. 9. Connect the power steering pressure hose to the power steering pump assembly (4). 10. Connect the power steering pressure hose to the power steering gear assembly (2). Tighten Tighten the power steering pressure hose to the steering gear to 27 N·m (20 lb ft). 11. Install the bolt/screws to the retaining clips (3). Tighten Tighten the retaining clip bolt/screws to 6 N·m (53 lb in). 12. Install the power steering gear assembly heat shield (1). 13. Lower the vehicle. 14. Fill and bleed the power steering system using, J 43485. Refer to Corporate Bulletin Number 83-32-09, dated November, 1998. Power Steering Pressure (Inlet) and Return (Outlet) Hose Replacement Procedure For 1999-2001 Vehicles: 1. Raise and suitably support the vehicle. Refer to Vehicle Lifting and Jacking in the General Information section of the Service Manual. 2. Drain the power steering fluid. Refer to Draining the Power Steering System in the Power Steering section of the Service Manual. 3. Remove the LH front wheel/tire assembly. 4. Remove the LH lower splash shield. 5. Remove the lower radiator air deflector (engine splash shield, if installed.

Related Content:

how to remove trumpet off of ford 2000 tractor, steering pressure hose replacement f250 - 7 3 - 4wd, Rav 4 steering rack dismantle and refit procedure, 99 buick park ave radiator installation, schematic for 99 taurus power steering, exploded view of a tilt steering column for 2001 plymouth neon 2 0l, how to replace 2003 impala power steering pump, 98 amigo isuzu how to remove power steering pump, how to change power steering pump 2009 acada, youtube replace the hub on a meritor ff981 axle

2003 Honda ODYSSEY Intake Manifold Removal and Installation Manual

0

Filed Under (Honda Manuals) by admin on 27-06-2012

download
Removal 1. Remove the intake manifold cover (A) and ignition coil cover(s) (B). 1999-2001 models: 2002-2004 models: 2. Remove the evaporative emission (EVAP) canister hose (A) (1999-2001 models) or vacuum hose (A) (2002-2004 models). 3. Remove the vacuum hose(s) (B) and breather pipe (C), then remove the intake air duct (D). 1999-2001 models: 2002-2004 models: 4. Remove the throttle cable (A) and cruise control cable (B) by loosening the locknuts (C), then slip the cable ends out of the accelerator linkage. Take care not to bend the cables when removing them. Always replace any kinked cable with a new one. 5. Remove the engine wire harness connectors and wire harness clamps from the intake manifold. *Intake air temperature (IAT) sensor connector *Idle air control (IAC) valve connector *Throttle position (TP) sensor connector *Manifold absolute pressure (MAP) sensor connector *Evaporative emission (EVAP) canister purge valve connector (2002-2004 models) 6. Remove the brake booster vacuum hose (A) and positive crankcase ventilation (PCV) hose (B). 7. Remove the vacuum hoses (C) (1999-2001 models). 1999-2001 models: 2002-2004 models: 8. Remove the breather hose (A) and water bypass hoses (B), then plug the water bypass hoses. 9. Remove the EVAP canister hose (C) (2002-2004 models). 1999-2001 models:

Related Content:

1999 honda civic ex manual, ashley recliner model 7528 parts, 2001 civic fuel canister pdf, ashley recliner model 7528 replacement parts, Honda Odyssey 2001 Parts Diagram, honda odyssey 2002 repair manual pdf, honda odyssey canister purge valve location, Savage Model 99 Manual, viper 4115v1remote start

1984-1995 Honda Civic/ CRX Positive Crankcase Ventilation (PCV) System Repair Manual

0

Filed Under (Honda Manuals) by admin on 22-04-2012

download
The PCV system is designed to prevent blow-by gas from escaping to the atmosphere by drawing it directly into the intake manifold. The PCV valve contains a spring-loaded plunger which is lifted in proportion to intake manifold vacuum. Under high vacuum, blow-by is returned directly to the manifold through the breather chamber and PCV valve with fresh air. When intake manifold vacuum decreases (wide open throttle) and vacuum in the air cleaner increases, the PCV valve closes and the blow-by is returned through the cylinder head cover breather hose and into the air cleaner. The PCV valve also acts as a check valve when the engine backfires to prevent crankcase explosion. Fig. 1: PCV system components-1984-87 1.5L engines Fig. 2: PCV system components-1988-91 1.6L engines Fig. 3: PCV system components-1992-95 engines Fig. 4: PCV system components-1984-87 carbureted engines SERVICE Positive Crankcase Ventilation (PCV) Valve For PCV valve removal, refer to Routine Maintenance of this information. 1. Locate the PCV valve. With the engine running at idle, use pliers to pinch the PCV hose between the valve and the intake manifold. It should be possible to hear the spring loaded valve click shut. 2. If no click is heard, remove the valve from the engine but leave it connected to the intake manifold. A hissing sound should be heard and vacuum should be felt at the valve inlet. 3. If no vacuum is felt, remove the valve from the intake manifold hose. The engine should stall or almost stall. This will indicate a stuck valve or clogged hose. Check the breather hose for clogging or leaks and replace any defective parts. Exhaust Gas Recirculation (EGR) System FUEL INJECTED ENGINES General Information See Figure 3 The Exhaust Gas Recirculation (EGR) system is used to control emissions measured at the tailpipe. Components included are the EGR valve and controls. The EGR system uses a poppet type valve to regulate the amount of exhaust gas flowing into the intake manifold. The flow path is cast into the cylinder head and does not use any external tubing. A control solenoid valve regulates the amount of vacuum to the EGR valve. A Constant Volume Control (CVC) valve provides a constant amount of vacuum to the control solenoid valve over a wide range of engine vacuum. When servicing or repairing any part of the emissions system, it is absolutely essential to check for any obvious mechanical faults or failures. Remember, a trouble code only indicates which sensor or circuit is affected by the problem. Simple mechanical faults such as a vacuum leak or poor electrical connection can cause a fault code. The EGR valve is not simply open or closed but is modulated by controlling the amount of engine vacuum to the valve diaphragm, up to a maximum of 8 in. Hg of vacuum. The EGR valve has a sensor in the top of the valve that reports valve lift to the ECU (same as ECM, 1992-95). The ECU modulates the position of the control solenoid valve to control the EGR valve lift according to an internal program. Upstream of the control solenoid valve, the CVC provides a constant supply of vacuum so EGR control is precise under all manifold vacuum conditions

Related Content:

2004 honda purge control valve, clean egr valve lincoln, c230 2005 removing pcv valve and hoses, 2008 hyundai elantra purge valve, fuel purge valve for 2006 chevy impala, pvc valve for 2001 merc sable 24 valve overhead cam, egr valve chevy trailblaxer 2005, where is the pcv valve on chevy cruze, 2007 implala vent solenoid replacement, where is the pvc valve located on a 2008 toyota tundra

Toyota Celica 1.8L 16v VVTi INSTALLATION INSTRUCTIONS

0

Filed Under (Toyota Manuals) by admin on 29-10-2011

download
1. Disconnect the negative terminal from the vehicle battery. 2. Unclip & remove the plastic trim from the front slam panel. (Fig. 1) 3. Unclip & remove the electrical harness plug from the MAS (Mass Air Sensor). (Fig. 2) 4. Unclip the MAS harness from the side of the air box. (Fig. 3) 5. Unclip & remove the intake hose from the MAS / air box lid. (Fig. 4) 6. Remove the vacuum hose from the inlet manifold (small rubber hose between the air box & manifold. (Fig. 5) 7. Fit the rubber blanking plug to the vacuum pipe located on the inlet manifold (ensure an air tight seal. (Fig. 6) 8. Unclip & remove the CFSV (carbon filter solenoid valve) from the air box lid. (Fig. 7) 9. Remove the 2 bolts securing the air box assembly & carefully lift out the assembly (Do not fully remove at this time). (Fig. 8&9) 10. From underneath the air box assembly unclip the blue electrical harness plug from the VSV (Vacuum solenoid valve). Now fully remove the air box assembly. (Fig.10) 11. Refit the plastic trim to the slam panel. 12. Remove the plastic ducting from between the fan cowling & ECU cover. (Fig.11&12) 13. Unclip & remove the intake hose from the throttle housing. (Fig.13) 14. Remove the bolt securing the relay unit to the chassis leg as shown. (Fig.14) 15. Secure the new mounting bracket to the relay mounting point located on the chassis leg using the M8 bolt & washer supplied. (Fig.15) 16. Clip the edge trim to the outside edge of the heat shield, cut away any excess trim. (Fig.16) 17. Attach the heat shield to the mounting bracket & secure using the M6 allen head bolts, nylock nuts & washers supplied. (Fig.17) 18. Unscrew & remove the bracket from the CFSV. (Fig.18) 19. Fit the new ‘L’ mounting bracket to the CFSV using the original screw. (Fig.19) 20. Secure the CFSV / mounting bracket to the side of the heat shield using the M5 bolt, nylock nut & washers supplied. (Fig.20) 21. Carefully unscrew & remove the MAS from the air box assembly. (Fig.21) 22. Stick the foam gasket to the hole located on the new molded intake pipe. Fit the MAS to the hole in the molded intake pipe & secure using the screws supplied. (Fig.22&23) 23. Assemble the new molded intake pipe using the silicone adaptor hose & rubber filter adaptor. (Fig.24) 24. Fit the new K&N filtercharger to the rubber filter adaptor & secure using the hose clamp supplied. (Fig.25) 25. Secure the new intake pipe assembly to the throttle housing using the stepped silicone hose & hose clips supplied (align the notch on the intake pipe with the notch on the throttle housing). (Fig.26) 26. Reconnect the electrical harness plug from the MAS. (Fig.27) 27. Secure the coolant hose & any excess harnesses using the plastic ties supplied. 28. Reconnect the negative battery terminal. 29. Carry out a final check of the alignment / fitment of the K&N induction system. Make any adjustments utilizing the slotted holes on the brackets & shield. Installation is now complete. (Fig.28

Related Content:

drawing mounting between intake manafold and block toyota 22R-E motor, heat sheilds on 2000 celica location, how to remove ecu 1992 toyota celica

1993-2002 Volkswagen Golf, Jetta, GTI, Cabrio A/C controls and mechanical components service manual

0

Filed Under (Volkswagen Manuals) by admin on 09-07-2012

download
1 – . Dust and pollen filter Where applicable 2 – . Plenum cover Removing/installing – -”> 3 – Evaporator water drain valve Located behind bulkhead insulation Removing/installing Fig. 2 Removing and installing evaporator water drain valve 4 – . Heater core connections and vacuum hose guide 5 – . Fresh Air/Recirculating Flap Two-Way Valve N63 Valve open when voltage applied Vacuum hose layout Vacuum hose layout 6 – . Coolant Fan Control (FC) Control Module J293 With fuse Fuse Strip S88 (1993 m.y.) With fuses Coolant Fan Second and Third Speed Fuse S107 and Coolant Fan First Speed and A/C Clutch Fuse S108 (1994 m.y. micro ) Connector terminal identification: micro 09.93 Fig. 5 Connector terminal identification of Coolant Fan Control (FC) Control Module J293 ( 09.93) 10.93 micro Fig. 6 Connector terminal identification of Coolant Fan Control (FC) Control Module J293 (10.93 ) 7 – . Vacuum reservoir Insert vacuum hose 30 mm (1.2 in.) into reservoir Removing/installing Fig. 7 Removing and installing vacuum reservoir A/C and heating system components, engine compartment Vacuum hose Vacuum hose layout Vacuum hose layout 9 – . A/C Cut-Out Thermal Switch F163 and Third Speed Coolant Fan Control (FC) Thermal Switch F165 A/C Cut-Out Thermal Switch F163 only on vehicles with engine codes AAA, AAZ, ABA, ACC A/C Cut-Out Thermal Switch F163 switches A/C Clutch N25 off at high engine coolant temperature; OFF (switch open) above 119 degree C (246 degree F); ON (switch closed) below 112 degree C (234 degree F) Third Speed Coolant Fan Control (FC) Thermal Switch F165 only on vehicles with 3- speed coolant fan motor Third Speed Coolant Fan Control (FC) Thermal Switch F165 switches radiator coolant fan to 3rd speed as engine coolant temperature increases; 3rd speed ON (switch closed) above 112 degree C (234 degree F); OFF (switch open) below 108 degree C (226 degree F) Removing and installing (engine code AAA) Fig. 3 Removing and installing A/C Cut- Out Thermal Switch F163 and Third Speed Coolant Fan Control (FC) Thermal Switch F165 (2.8 liter VR6 engine code AAA) Removing and installing (engine code ABA) Fig. 4 Removing and installing A/C Cut- Out Thermal Switch F163 (2.0 liter engine code ABA) 10 – . Condenser* 11 – . Pressure relief valve*

Related Content:

wiring diagram for the drivers side front electric window switch on a 1998 ford contour, 02 Jetta Fan Control Module, 2002 lincoln ls cooling system diagram, fan fuse for 1995 chevy lumina, fan sensor vw beetle how to change, how to replAce mounting on evap canister on 2001 f150 to truck body, Mazda MPV Fan Control Module 2002

EDELBROCK PERFORMER SERIES CARBURETORS INSTALLATION INSTRUCTIONS

0

Filed Under (More Manuals) by admin on 27-12-2011

download
Figure 1 – Fittings and Vacuum Port Locations INSTALLATION PROCEDURE BEFORE REMOVING OLD CARBURETOR 1. Determine if the distributor vacuum port is timed (no vacuum at idle) or full (vacuum present at idle). With the engine at operating temperature and idling, pull the vacuum advance hose off of the carburetor and “feel”for vacuum by putting your finger on the vacuum port (See Fig. 2) . If your distributor has timed vacuum advance, you will hook the vacuum hose from the distributor to the passenger side vacuum port on the new carburetor. If it has full vacuum advance, it will be hooked up to the driver side port. 2. The stock steel fuel line must be converted to fuel resistant rubber hose. The stock steel line will not connect to the Performer Series Carburetor. Use Edelbrock Universal Fuel Line Kit #8135. This kit contains a filter, neoprene hose, and fittings to adapt to 5/16″or 3/8″stock steel fuel lines (See Fig. 3) . NOTE: After cutting the steel line, remove sharp edges and clean out any chips. 3. Always use a new fuel filter. Failure to do so will void your warranty. 4. You must use Edelbrock Adapter #2696 or Adapter & Fuel Line Kit #2697 when installing a Performer Series carburetor on a General Motors Quadrajet or Chrysler Thermoquad intake manifold. #2697 includes adapter #2696 and fuel line kit #8135. Do not use an open adapter! (See Fig. 4) 5. You must use Edelbrock Adapter #2732 when installing a Performer Series carburetor on certain Edelbrock intake manifolds. In those applications, install the adapter as shown (See Fig. 5)

Related Content:

edelbrock carburetor repair guide, edelbrock edl 1406 overhaul manual, quicksilver carb instructions, Throttle springs Carter Thermo Quad

2001 Lincoln LS Intake Manifold Upper Removal And Installation Manual

0

Filed Under (Lincoln Manuals) by admin on 27-02-2011

download
Intake Manifold — Upper Removal 1. Disconnect the battery ground cable. For additional information, refer to Section 414-01. 2. Drain the engine cooling system. For additional information, refer to Section 303-03 . 3. Remove the engine appearance cover. 4. Remove the air cleaner outlet tube. For additional information, refer to Section 303-12 . 5. Disconnect the throttle position (TP) sensor and the idle air control (IAC) solenoid electrical connectors. 6. Disconnect the accelerator and speed control cables. 7. Remove the cable bracket. 1. Remove the bolts. 2. Remove the bracket. 8. Disconnect the throttle body hoses. 1. Disconnect the coolant hoses. 2. Disconnect the positive crankcase ventilation (PCV) hose. 3. Disconnect the vapor purge hose. 9. Disconnect the vacuum hose. 10. Disconnect the EGR to exhaust manifold tube nut. 11. Remove the cowl vent screen. For additional information, refer to Section 501-02 . 12. Remove the brace. 13. Remove the vacuum hoses from the mounting bracket. 14. Remove the bracket and position the accelerator and cruise control cables aside. 15. Disconnect the differential pressure feedback EGR electrical connector. 16. Remove the stud and nut and position the differential pressure feedback EGR transducer aside. 7. Remove the fuel pressure sensor shield. 1. Remove the nut. 2. Remove the bolts. 3. Remove the shield. 18. Disconnect the vacuum hose from the rear of the upper intake manifold. 19. Disconnect the intake manifold tuning valve (IMTV) electrical connector. 20. Disconnect the exhaust vacuum regulator (EVR). 1. Disconnect the electrical connector. 2. Disconnect the vacuum line. 21. Remove the upper intake support bolt. 22. Remove the front intake manifold support bolt.

1998 Ford Ranger Heavy Duty Floor Crane Workshop Manual

0

Filed Under (Ford Manuals) by admin on 02-02-2012

download
1. Relieve the fuel pressure. For additional information, refer to Section 310-00 . 2. Disconnect the battery ground cable (14301). For additional information, refer to Section 414-01 . 3. Drain the engine cooling system. For additional information, refer to Section 303-03 . 4. Remove the hood (16612). 5. Remove the air cleaner outlet tube (9B659). For additional information, refer to Section 303-12 . 6. Remove the accelerator control splash shield (9E766). 7. Remove the upper radiator hose (8260). 8. Remove the lower radiator hose (8286). 9. Remove the two bolts and position the fan shroud (8146) on the fan blade (8600). 10. Remove the water pump pulley, fan and shroud; refer to Section 303-03 . 11. Disconnect the radiator overflow tube. 2. On vehicles equipped with automatic transmissions, disconnect the transmission cooler lines. 13. Disconnect the mass air flow sensor. 14. Disconnect the heater water hoses (18472) at the inlet and outlet; refer to Section 303-03 . 15. Disconnect the power connection from the generator (10346). 16. Disconnect the vacuum connection to the vacuum reservoir. 17. Disconnect the throttle body heater hose. 18. Disconnect the A/C cycling switch. 19. Disconnect the connector from the powertrain control module (PCM) (12A650). 20. Remove the nut. 21. Remove the ground wire stud from the powertrain control module. 22. Recover the A/C system; refer to Section 412-00 . 23. Disconnect the power steering cut-out switch. 24. Disconnect the peanut fitting from the A/C condenser core (19712). 25. Disconnect the A/C high pressure cut-out switch. 26. Disconnect the A/C manifold hose. 27. Remove the nut. 28. Disconnect the accelerator cable (9A758) and the speed control cable. 29. Disconnect the brake booster vacuum hose and vacuum tube at the upper intake manifold assembly. 30. Disconnect the EVR vacuum supply hose and the vacuum reservoir vacuum line. 31. Disconnect the wiring connector. 32. Disconnect the fuel line; refer to Section 310-01 . 33. Remove the A/C compressor; refer to Section 412-03 . 34. Disconnect the power steering pressure and return hoses. 35. Remove the nut retaining the wiring harness. 36. Disconnect the block heater if equipped. 37. Raise the vehicle on a hoist; refer to Section 100-02 . 38. Disconnect the engine ground cable

Related Content:

disconnect battery dodge journey, disconnect the abs sensor on a 2005 maxima, if the canister purge valve is bad would it cause your car to stall, vapor separator tank 1971 jeepster commando

Honda Civic/ CRX Positive Crankcase Ventilation (PCV) System OPERATION MANUAL

0

Filed Under (Honda Manuals) by admin on 28-01-2012

download
The PCV system is designed to prevent blow-by gas from escaping to the atmosphere by drawing it directly into the intake manifold. The PCV valve contains a spring-loaded plunger which is lifted in proportion to intake manifold vacuum. Under high vacuum, blow-by is returned directly to the manifold through the breather chamber and PCV valve with fresh air. When intake manifold vacuum decreases (wide open throttle) and vacuum in the air cleaner increases, the PCV valve closes and the blow-by is returned through the cylinder head cover breather hose and into the air cleaner. The PCV valve also acts as a check valve when the engine backfires to prevent crankcase explosion. Fig. 1: PCV system components-1984-87 1.5L engines Fig. 2: PCV system components-1988-91 1.6L engines Fig. 3: PCV system components-1992-95 engines Fig. 4: PCV system components-1984-87 carbureted engines
SERVICE Positive Crankcase Ventilation (PCV) Valve For PCV valve removal, refer to Routine Maintenance of this information. 1. Locate the PCV valve. With the engine running at idle, use pliers to pinch the PCV hose between the valve and the intake manifold. It should be possible to hear the spring loaded valve click shut. 2. If no click is heard, remove the valve from the engine but leave it connected to the intake manifold. A hissing sound should be heard and vacuum should be felt at the valve inlet. 3. If no vacuum is felt, remove the valve from the intake manifold hose. The engine should stall or almost stall. This will indicate a stuck valve or clogged hose. Check the breather hose for clogging or leaks and replace any defective parts. Exhaust Gas Recirculation (EGR) System FUEL INJECTED ENGINES General Information See Figure 3 The Exhaust Gas Recirculation (EGR) system is used to control emissions measured at the tailpipe. Components included are the EGR valve and controls. The EGR system uses a poppet type valve to regulate the amount of exhaust gas flowing into the intake manifold. The flow path is cast into the cylinder head and does not use any external tubing. A control solenoid valve regulates the amount of vacuum to the EGR valve. A Constant Volume Control (CVC) valve provides a constant amount of vacuum to the control solenoid valve over a wide range of engine vacuum.

Related Content:

1993 Corvette Service Manual PDF, vent line 1998 mercy sable, ford taurus 2001 engine vacuum hoses on intake, What color is the tcc solenoid in toyota sequoia, 2002 2 4L olds alero vacuum hose routing diagram, vacume lines on 2004 pt cruiser gt, VACUUM LINES ON A 2003 GM 6 CLINDER, is there a vacuum hose on the transmission of a ford fusion, vaccum lines 2001 pt cruiser, Does a volvo d12 engine require silicone or gasket between engine and flywheel housing