Skip to content

w56 transmission rebuild manual

You search PDF repair manual about w56 transmission rebuild manual, if there are search results will appear below. If search results do not exist, please search by others keyword.

2004 Ford Truck Ranger 2WD Transmission Position Switch/ Sensor Service and Repair MANUAL

download
Special Tool(s) Removal 1. With the vehicle in NEUTRAL, position it on a hoist. 2. Disconnect the shift cable from the manual control lever. 3. Disconnect the digital transmission range (TR) sensor electrical connector. 4. Remove the manual control outer lever nut and manual control outer lever. 2004 Ford Truck Ranger 2WD V6-4.0L VIN E 5. Remove the screws and the digital TR sensor. Installation 1. Install the digital TR sensor and loosely install the screws. 2. CAUTION: Tightening one screw before tightening the other may cause the sensor to bind or become damaged. NOTE: The manual lever must be in the NEUTRAL position. Using the special tool, align the digital TR sensor and tighten screws in an alternating sequence. 3. Install the manual control outer lever and nut. 2004 Ford Truck Ranger 2WD V6-4.0L VIN E Copyright © 2007, ALLDATA 9.50 Page 3 4. Connect the digital transmission range (TR) sensor electrical connector. 5. Connect the shift cable to the manual control lever. 6. Verify that the shift cable is adjusted correctly.

2000 Pontiac Bonneville V6-3.8L VIN K – A/T 4T65E Harsh Shifts/Shudders/Slips Repair Manual

download
Line Pressure Check Procedure Tools Required Important: Before performing a line pressure check, verify that the pressure control (PC) solenoid valve is receiving the correct electrical signal from the PCM. Caution: Keep the brakes applied at all times in order to prevent unexpected vehicle motion. Personal injury may result it the vehicle moves unexpectedly. J 21867Universal Pressure Gauge Set 1. Install a Scan Tool. 2. Start the engine and set the parking brake. 3. Check for a stored Diagnostic Trouble Code (DTC). 4. Repair the vehicle, if necessary. 5. Check the fluid level. Refer to the Transmission Fluid Checking Procedure. 6. Check the manual linkage for proper adjustment. 7. Turn the engine OFF. Remove the oil pressure test hole plug and install the J 21867. 8. Put the gear selector in PARK range and set the parking brake. 9. Start the engine and allow the engine to warm up at idle Notice: Total test running time should not be longer than two minutes, or else transmission damage could occur. Notice: Refer to Fastener Notice in Cautions and Notices. Parts Information 10. Access the PC solenoid valve control test on the Scan Tool. Zoom Sized for Print 11. Increase the PC solenoid as shown actual current from 0.0 to 1.0 amps in 0.1 amp increments. Allow the pressure to stabilize for five seconds after each pressure change. Read the corresponding line pressure on the J 21867. 12. Refer to the Line Pressure specification table. Compare the data to the table. 13. If pressure readings differ greatly from the table, refer to Incorrect Line Pressure. 14. Remove the J 21867. 15. Apply sealant, P/N 12345382 (in Canada, P/N 10953489), to the oil pressure test hole plug. 16. Install the oil pressure test hole plug. Tighten Tighten the oil pressure test hole plug to 12 N.m (106 lb in).

2002 Land Rover Freelander (LN) V6-2.5L Automatic Transmission/Transaxle Service and Repair Manual

download
Automatic Transmission/Transaxle: Service and Repair Gearbox – KV6 – NAS Models JATCO Gearbox – KV6 – NAS models Remove 1. Position the vehicle on a twin-post lift. 2. Tie bonnet back in upright position. 3. Disconnect battery earth lead. 4. Remove engine acoustic cover. 5. Release HO2S multiplug from support bracket on LH camshaft cover, disconnect multiplug. 6. Raise vehicle on lift. 7. Remove rear beam. 8. Remove RH catalytic converter 2002 Land Rover Freelander (LN) V6-2.5L Copyright © 2010, ALLDATA 10.20 Page 3 12. Remove bolt securing front pipe to bracket and remove front pipe. Discard gasket. 13. Remove 3 screws securing LH splash shield and remove shield 14. Release HO2S lead from clip on cylinder block. Remove 4 nuts securing exhaust manifold to cylinder head, remove manifold and discard gasket. 15. Drain fluid from IRD. 16. Drain gearbox fluid. 17. FitLRT-54-026 to the RH drive shaft inboard joint. 18. Using a suitable lever, release drive shaft from IRD. 19. With assistance, pull hub outwards and release drive shaft from IRD. CAUTION: Care must be taken not to damage oil seal when removing drive shaft from IRD. CAUTION: To avoid damage to gaiter or joint, do not allow shaft to hang on joint. 20. Remove LRT-54-026 from RH drive shaft inboard joint.

1991 Subaru Loyale Sedan (4 Door) Camshaft And Timing Belt Repair Manual

download
Tightening torque: REMOVAL 1. Loosen water pump pulley mounting nuts or bolts. 2. Loosen two alternator mounting bolts, and detach V-belt. [Except air conditioner equipped model] 3. Remove water pump pulley and pulley cover. 4. Disconnect lead from oil pressure switch. 5. Remove oil level gauge guide together with gauge. 6. Remove crankshaft pulley. To lock crankshaft, use FLYWHEEL STOPPER [manual transmission model] or DRIVE PLATE STOPPER [automatic transmission model]. 7. Remove belt cover plate. [TURBO model] 8. Remove belt covers LH, RH and FR. 9. Removing timing belt Zoom Sized for Print (a) Loosen tensioner mounting bolts on # 1 cylinder by 1/2 turn. (b) With tensioner fully turned to slacken belt, tighten mounting bolts. (c) Mark rotating direction of timing belt, then remove belt. (d) Loosen tensioner No. 2 mounting bolts on # 2 cylinder by 1/2 turn. (e) With tensioner fully rotated to slacken belt by using TENSIONER WRENCH, tighten tensioner mounting bolts. NOTE: Cover TENSIONER WRENCH clamping tips with a rubber hose or waste cloth to prevent crankshaft or pulley from being damaged 10. Remove tensioner and tensioner No. 2 together with tensioner spring. 11. Remove belt idler. 12. Remove camshaft sprockets by using CAMSHAFT SPROCKET WRENCH. 13. Remove right-hand belt cover No. 2, left-hand belt cover No. 2 and belt cover RR. TIMING BELT 1. Check timing belt teeth for breaks, cracks, and wear. If any fault is found, replace belt. 2. Check the condition of back side of belt; if any crack is found, replace belt. A. Be careful not to let oil, grease or coolant contact the belt. Remove quickly and thoroughly if this happens. Zoom Sized for Print

HONDA Accord V6, Odyssey, Pilot Idle Vibration or Harsh Shifting Repair Manual

download
SYMPTOM There is a vibration at idle or harsh engagement when shifting the transmission between between Park, Drive, and Reverse. PROBABLE CAUSE The front hydraulic engine mount may have deteriorated and torn. PARTS INFORMATION Front Engine Mount Assembly: 1998-02 Accord V6 – P/N 50810-S87-A82, H/C 7981657 1999-04 Odyssey – P/N 50800-S0X-A04, H/C 7978927 2003-05 Pilot – P/N 50800-S3V-A82, H/C 7984560 WARRANTY CLAIM INFORMATION In warranty: The normal warranty applies. Failed Part: P/N 50810-S87-A81 H/C 5438593 Defect Code: 01102 Symptom Code: 04501 Skill Level: Repair Technician Out of warranty: Any repair performed after warranty expiration may be eligible for goodwill consideration by the District Parts and Service Manager or your Zone Office. You must request consideration, and get a decision, before starting work. DIAGNOSIS 1. Bring the engine up to operating temperature, and fully apply the parking brake. 2. Have an assistant view the top of the front engine mount while standing to the side of the vehicle. Shift the transmission to Drive. With your foot firmly on the brake pedal, quickly depress the accelerator pedal and release it. Your assistant should look for contact between the top of the engine mount and the bottom of the front engine mount bracket, and listen for noise from that area. REPAIR PROCEDURE 1. Drive the vehicle onto a lift, but do not raise it. 2. Odyssey – Remove the intake manifold cover and the front ignition coil cover: •See page 9-4 of the 1999-04 Odyssey Service Manual. •Online, enter keyword INTAKE , and select Intake Manifold Removal and Installation from the list. 3. Odyssey – Remove the radiator cover: •See page 10-16 of the 1999-04 Odyssey Service Manual. •Online, enter keyword RADIATOR , and select Radiator and Fan Replacement from the list