Skip to content

what can cause the fuel gauge on a 2001 chrysler town and country to not work correctly

You search PDF repair manual about what can cause the fuel gauge on a 2001 chrysler town and country to not work correctly, if there are search results will appear below. If search results do not exist, please search by others keyword.

2000 Ford Windstar INCORRECT FUEL GAUGE INDICATION Workshop Manual

download
The fuel gauge does not change indication unless there has been at least 3 gallons of fuel added or deleted between ignition switch cycle. Use recorded REM and instrument cluster DTCs from the Continuous and On- Demand self-test. ? Are any DTCs recorded? Yes If REM DTC B1201 or IC DTC U1131 is retrieved, GO to D6 . No GO to D2. D2 CARRY OUT THE ICM FUEL GAUGE ACTIVE COMMAND IC Active Command Select the IC FUEL GAUGE CONTROL active command. Trigger FUELLEVEL active command. Toggle and monitor the fuel gauge while adjusting the FUELLEVEL active command to read 50% and 100% Did the fuel gauge needle start at empty (E), move to half at 50%, and full (F) at 100%? Yes GO to D3. No INSTALL a new instrument cluster; REFER to Instrument Cluster. CLEAR the DTC. REPEAT the instrument cluster self-test. D3 CHECK THE FUEL GAUGE READING Fuel Pump Module C412 Connect one lead of Instrument Gauge System Tester to fuel pump module C412 Pin 5, Circuit 1357 (LB/YE), harness side. Connect the other lead to fuel pump module C412 Pin 8, Circuit 1356 (LG/VT), harness side. Set the power switch on Instrument Gauge System Tester to the ON position Set Instrument Gauge System Tester to 15 ohms. Wait one minute. Set Instrument Gauge System Tester to 160 ohms. Wait one minute. Read the fuel gauge. The fuel gauge should read full or above. Set Instrument Gauge System Tester to 15 ohms. Wait one minute. Read the fuel gauge. The fuel gauge should read empty or below Does the fuel gauge operate correctly? Yes GO to D4. No GO to D6. D4 INSPECT THE FUEL TANK Visually inspect the fuel tank for any damage or deformation. ? Is the fuel tank OK? Yes GO to D5. No INSTALL a new fuel tank. REFER to Section 310-01. TEST the system for normal operation. D5 INSPECT THE FUEL LEVEL SENSOR AND PUMP ASSEMBLY Visually inspect the fuel pump assembly for damaged wiring or connectors. Visually inspect the float and float rod for damage or obstruction

1998 Dodge Grand Caravan Fuel Pump Relay Removal And Installation Manual

download
Fuel Pump Relay 1. Remove fuel pump relay from power distribution center at driver’s side front corner of engine compartment, near the battery. Note terminal identification on fuel pump relay. See Fig. 6 . 2. To check fuel pump relay resistance, use ohmmeter and check resistance between terminals No. 85 and 86 on fuel pump relay. Replace fuel pump relay if resistance is not 70-80 ohms. 3. To check fuel pump relay operation, connect ohmmeter between terminals No. 30 and 87A on fuel pump relay. See Fig. 6 . Ohmmeter should indicate continuity between terminals No. 30 and 87A on fuel pump relay. 4. Connect ohmmeter between terminals No. 30 and 87 on fuel pump relay. See Fig. 6 . Ohmmeter should indicate no continuity between terminals No. 30 and 87 on fuel pump relay. 5. Connect 16-gauge jumper wire between negative battery terminal and terminal No. 85 on fuel pump relay. Connect 16-gauge jumper wire between positive battery terminal and terminal No. 86 on fuel pump relay. 6. Fuel pump relay should now be energized. No continuity should now exist between terminals No. 30 and 87A on fuel pump relay. Continuity should now exist between terminals No. 30 and 87 on fuel pump relay. Disconnect jumper wires. Replace fuel pump relay if defective. 7. If fuel pump relay or wiring circuit failure exists, a Diagnostic Trouble Code (DTC) will be stored in Powertrain Control Module (PCM). See appropriate G – TESTS W/CODES article. Fig. 6: Identifying ASD Relay & Fuel Pump Relay Terminals Courtesy of CHRYSLER CORP.

2001 Ford F-150 Draining-Coalescer/ Pressure Relief-Natural Gas Bi-Fuel System Repair Manual

download
1. Relieve the Bi-fuel system fuel pressure. For additional information, refer to Pressure Relief—Natural Gas Bi-Fuel System. 2. Raise the vehicle on the hoist. For additional information, refer to Section 100-02. 3. NOTE: There is an O-ring attached to the drain plug. The O-ring must be replaced each time the drain plug is removed. Remove the drain plug. 4. Install the drain plug. 5. Lower the vehicle. 6. Pressurize the fuel system. WARNING: It is important that your bi-fuel vehicle be correctly maintained by Ford bi-fuel trained personnel. If a concern occurs, it is important that correctly trained personnel diagnose the cause. If a concern relates to the fuel system, correct part replacement is imperative to keep your vehicle operating at normal performance. Bi-fuel components and gasoline specific components are not interchangeable. If your vehicle is not serviced in accordance with bi-fuel service procedures, damage can occur and your warranty may be invalidated. WARNING: Fuel supply lines are always pressurized. When servicing fuel related components, do not smoke or carry lighted tobacco or an open flame of any type. Flammable mixtures may be present and can ignite, resulting in personal injury. WARNING: The natural gas fuel system is always pressurized to 655 kPa (95 psi) downstream of the fuel pressure regulator and up to 24821 kPa (3,600 psi) upstream of the fuel pressure regulator. Use care when servicing the fuel system or personal injury can occur. WARNING: The natural gas fuel supply manifold is pressurized to 655 kPa (95 psi). Fuel pressure must be relieved prior to any fuel system service. WARNING: The fuel system pressure must be relieved before any component can be removed. The fuel tanks must be evacuated prior to tank removal. Removal of components without pressure relief or tank evacuation can cause natural gas to escape into the air and cause injury or death.

2004-2007 Ford Explorer MIL ON WITH DTC P0463 OR ERRATIC FUEL GAUGE OPERATION SERVICE PROCEDURE

download
ACTION Follow the Service Procedure steps to correct the condition. SERVICE PROCEDURE 1. For vehicles with customer symptom of erratic fuel gauge operation (with no MIL on), proceed to Step 1a. For vehicles with a customer symptom including the MIL on, proceed to Step 1b. If unable to verify the concern, do not continue with this TSB. a. Follow the appropriate pinpoint test (PPT) for “Fuel Gauge Inaccurate” in Workshop Manual (WSM), Section 413-01. If PPT test results lead to fuel pump module replacement, proceed to Step 2. If PPT test results isolate any problem other than fuel pump module replacement, repair as indicated and do not continue with this TSB. b. Install diagnostic scan tool to retrieve DTCs. If DTC P0463 is retrieved, proceed to Step 2. If DTC P0463 is not retrieved, this TSB does not apply, follow normal WSM diagnostics. 2. Remove fuel tank per WSM, Section 310-01 3. Remove fuel pump assembly from fuel tank per WSM, Section 310-01. See Figure 1 (Chart) to determine if a kit (contains a fuel level sensor assembly, a wire harness and heat shrink tube) or fuel pump assembly is required for repair. For vehicles that can be serviced with a kit go to Step 4. For vehicles that require fuel pump assembly replacement, go to Step 12. 4. Remove the fuel level sensor assembly (sender card/float rod assembly) from the fuel pump assembly per WSM, Section 310-01

1998-1999 Chevrolet and GMC S/T Pickup and 2 Door Utility Incorrect Fuel Gauge Readings

download
Condition Some owners may comment on incorrect fuel gauge readings. The fuel gauge may read empty (E) with approximately 1/3 of a tank of fuel remaining, or the fuel gauge rarely reaches the full (F) mark when the fuel tank is filled. Correction Reprogram the vehicle control module (VCM) with the revised Fuel System Calibration. Use the appropriate calibration listed below. Refer to the latest Techline information for programming procedures. Calibration Information Important: These calibrations are not available from GMSPO. These calibrations are available Subject: Incorrect Fuel Gauge Readings (Reprogram Vehicle Control Module with Revised Calibration) Models: 1998*-99 Chevrolet and GMC S/T Pickup and 2 Door Utility Models 1998*-99 Isuzu Hombre with 4.3L Engine (VINs W, X – RPOs L35, LF6) *RPO ZN4 Only Plant Division VIN Breakpoint Linden Chevrolet (Blazer) XK162355 Linden GMC (Pickup) XK508493 Linden GMC (Jimmy) XK508505 Shreveport Chevrolet X8140835 Shreveport GMC X8512385 Shreveport Isuzu (RPO ZN4 W8668201-W8670669 Shreveport Isuzu X8650007-X8650733 Calibration P/N (New) Application 09374032 (Fuel System Calibration) S/T 100 (Pickup) &LF6/L35 09374033 (Fuel System Calibration)