Skip to content

what is the resistor for 1996 buick

You search PDF repair manual about what is the resistor for 1996 buick, if there are search results will appear below. If search results do not exist, please search by others keyword.

1997-1998 Buick Regal GS & Pontiac Grand Prix GTP with L67 3.8L V6 Engine Fuel Pump Resistor Service Procedure

download
The following are instructions for removing the fuel pump resistor from its original mounting location on the lower right front body rail as shown in Figure 1, and replacing it with a new fuel pump resistor and cover in new location shown in Figure 2. The new location is on the front of dash sheet metal (3) at the rear of the engine compartment, inboard or to the left of the alternator (4). The passenger or right side windshield wiper arm (5) and stop (6) are called out for reference purposed only. 1. Turn the steering wheel to the full right position. 2. Open the hood and disconnect the negative battery cable. 3. Remove the diagonal brace (1) from over the windshield washer solvent reservoir by removing the two bolts (2) that attach it to the radiator support and the one bolt (3) that attaches it to the strut tower. Refer to Figure 3 4. Remove the two plastic push-in retainers (1) that attach the windshield washer solvent reservoir (2) to the radiator support (3) and the one nut (4) that attaches it to the strut tower (5). Refer to Figure 4. 5. Reposition the reservoir for access to the area rearward of the battery. 6. Raise the vehicle on a hoist. 7. At the right front wheel opening, remove the three screws that attach the inner fender splash shield to the front fascia at the wheel opening and the two screws that attach it to the bottom of the fascia. Refer to Figure 5. 8. Reposition the inner fender splash shield (1) to access the fuel pump resistor (2). Refer to Figure 1 at the beginning of this procedure. 9. Unclip the fuel pump resistor electrical connector from the body and disconnect the connector. 10. Remove the 10mm hex head bolt attaching the fuel pump resistor to the body and discard both the bolt and the resistor.

How to bypass the VATS (PASSKey II) system in a late model GM vehicle

download
Pontiac 1994-1996 Grand Prix 1992-1999 Bonneville 1993-2002 Firebird/Trans Am/Firehawk Buick 1994-1996 Regal 1992-1999 LeSabre 1991-1996 Park Avenue 1991-1996 Roadmaster Oldsmobile 1994-1997 Cutlass Supreme 1992-1999 Eighty Eight/LSS/Ninety Eight/Regency 1991-1996 Custom Cruiser Wagon Chevrolet 1995-1999 Monte Carlo 1995-2001 Lumina 1993-2002 Camaro 1986(?)-1996 Corvette (C4) Cadillac How to bypass the VATS system in a late model GM vehicle Bullet-Style” solderless connectors Heat Shrink Tubing Resistors of varying values (totalling the resistance measured across the key’s “pellet”) Alright, let’s begin the madness: 1. Take your DMM, set it to measure Ohms (use the 20k setting.) Measure the resistance across the pellet of the ignition key. Place one probe on the silver part of one side of the pellet, and the other probe on the other side. Write this value down. 2. Purchase a resistor or resistors that add up to the value measured in step 1. Radio Shack is a great place to go for the resistors, heat shrink tubing, and the “bullet-style” solderless connectors. 3. Take the 16 ga. wire and cut into 2 four-inch pieces. 4. Strip off approx 1/16″ of insulation off each side of both wire pieces. 5. Put your resistors together in series (or if you’re lucky and have a chip that has a resistance that matches a single resistor) and solder one wire to one end of the resistor(s) and the other wire to the other side. Example: You measure 11.72 on the 20k (k meaning kilo or 1,000) scale. The closest match is 11.801 which is a #15 “chip.” Always remember that resistors have a tolerance of 2%, meaning the resistance value of the “pellet” can be either 2% higher or 2% lower than 11.801 k ohms (11.72 falls in tolerance range.) You will want to aim for 11,801 ohms. So when you go to Radio Shack you want to pick up a 10,000 ohm (10k,) a 1,000 ohm (1k,) and an 800 ohm resistors to wire together in series to achieve the 11.801k ohm value.

1999 Buick Regal DTC B1001 Option Configuration Error Repair Manual

download
Test Description The number(s) below refer to the step number(s) on the diagnostic table. 2. This step checks to see if the correct VIN is programmed in the powertrain control module (PCM). 4. This step checks to see if the body control module (BCM) has been replaced. 5. This step explains the proper steps to perform after a BCM has been replaced in order for the <- Back Forward -> Document ID# 385021 1999 Buick Regal Print BCM to operate properly. 6. This step checks to see if the correct VIN is programmed in the BCM. 7. This step explains how to properly program the VIN into the BCM. DTC B1001 Option Configuration Error Step Action Value (s) Yes No 1 Was the SIR Diagnostic System Check performed? — Go to Step 2 Go to SIR Diagnostic System Check 2 1. Install the scan tool. 2. Use the scan tool to verify that the PCM is programmed with the correct VIN by comparing the VIN that is stored in the PCM to the VIN plate of the vehicle. Is the PCM programmed with the correct VIN? — Go to Step 4 Go to Step 3 3 Use the scan tool and/or the techline machine to program the correct VIN into the PCM. Is the programming procedure complete? — Go to Step 9 — 4 Was the BCM replaced? — Go to Step 5 Go to Step 6 5 1. Use the F2 function key and follow the instructions on the scan tool under the BCM SPECIAL FUNCTIONS to reprogram the BCM. This allows the BCM to learn the Restraints ID from the SDM and also to learn other important data that is required. 2. Use the F6 function key and follow the instructions on the scan tool under the BCM SPECIAL FUNCTIONS to program the correct VIN into the BCM. 3. Use the techline machine to perform the theft relearn procedures for the replacement BCM. Are the programming procedures complete? — Go to Step 9 — 6 Use the scan tool to verify that the BCM is programmed with the correct VIN by comparing the VIN that is stored in the BCM to the VIN that is stored in the PCM. Is the BCM programmed with the correct VIN? — Go to Step 8 Go to Step 7 7 Use the F6 function key and follow the instructions on the scan tool under the BCM SPECIAL FUNCTIONS to program the correct VIN into the BCM. Is the reprogramming procedure complete? — Go to Step 9 — 1. Turn the ignition switch to the OFF position. 2. Replace the SDM. Refer to Inflatable Restraint

1989-1996 Dodge Dakota Trucks COIL Ignition Tests Manual

download
Dakota Trucks 1989-1996 Ignition Tests COIL The ignition coil for the vehicles covered by this guide is in the following locations: • 1989-92 engines: mounted to the firewall • 1993-96 2.5L engines: mounted on the thermostat housing in front of the coolant temperature sensor • 1993-96 V6 and V8 LDC engines: mounted to a bracket bolted to the right engine cylinder head • 1993-96 5.9L HDC engines: mounted to a bracket bolted to the air injection pump (AIR pump) mounting bracket. Fig. 2: Ignition coil mounting-all 1989-92 models Fig. 3: Ignition coil wiring and mounting hardware-1993- 96 2.5L engine 1. Inspect the ignition coil for arcing while the engine is running. If the engine will not start, this can be performed while the engine is cranked by either an assistant or a remote starter. Look at the coil in dim or low light to aid visibility of any arcing. Fig. 4: Ignition coil mounting-1993-96 3.9L and 5.2L/5.9L LDC engines 2. Arcing at the tower will carbonize the wire boot, which, if it is connected to a new ignition coil, will cause the coil to fail. In such cases, clean all the carbonization away or replace the components as necessary. Fig. 5: Ignition coil mounting-1993-96 5.9L HDC engine 3. Using a coil tester or ohmmeter according to the manufacturer’s instructions, test the primary and secondary resistance. Replace any coil that does not meet the specifications indicated in the accompanying chart. 4. Inspect the secondary coil wire for any sign of damage. Replace if any damage is found. Carbon tracking on the old wire can cause arcing and the failure of a new ignition coil. REMOVAL & INSTALLATION 1989-92 Models See Figures 6 and 7 1. Disconnect the negative battery cable. 2. Disconnect the three wires from the coil. Mark them to identify for installation. Fig. 6: Remove the coil bracket bolt at the cowl Fig. 7: Unscrew the coil mounting hardware, then remove the coil from the vehicle 3. Unplug the condenser suppressor connector from the coil, if equipped. 4. Unbolt and remove the coil. To install: 5. Bolt down the coil with old bolts. 6. Connect wires to coil making sure that the proper wires are connected where they should be. 7. Connect the condenser suppressor, if equipped. 8. Connect the battery negative cable Removal and Installation V6 AND V8 ENGINES 1. Disconnect the negative battery cable. 2. Disconnect the primary wiring from the ignition coil. 3. Disconnect the secondary spark plug wire from the coil. 4. Remove the two bolts and withdraw the coil from its mounting bracket. To install:
5. Position the coil on its bracket and install the two bolts. Tighten them to 100 inch lbs. (11 Nm). If the bracket has been tapped for coil mounting bolts, these fasteners require less torque, so tighten them to 50 inch lbs. (5 Nm). 6. Connect all wiring to the ignition coil. TESTING See Figure 1 The only test you can perform without a DRBII scan tool, or equivalent, is a basic check of the sensor only.

1996-2000 Honda Civic Door Panel REMOVAL And INSTALLATION Manual

download
Honda Door Panel 96-00 Civic REMOVAL & INSTALLATION Remove the screw from behind the interior door handle Slide out the door handle trim as shown Removing the door panel from the passenger side door View of the inside of the door, panel removed 1. Remove the screw from the door handle trim. 2. Slide the handle assembly forward and out to access the lock rod clip. 3. Release the clip 4. Disconnect the door lock switch 5. Remove the door opener handle assembly. 6. Carefully pry at the small opening on the bottom of the speaker grill. 7. Remove the speaker grille. 8. Remove the speaker mounting screws. 9. Detach the electrical connector and remove the speaker. 10. Remove the screws in the armrest. 11. Remove the center from the trim clip at the upper front of the door panel and remove the clip. 12. Using a suitable trim panel removal tool, unsnap the door panel from the door frame. 13. Carefully lift the door panel up and away from the door frame. To install: 14. Installation is the reverse of the removal procedure. Honda Civic/Del Sol 1996-2000 Electric Window Motor REMOVAL & INSTALLATION 1. Remove the regulator from the door assembly. 2. Except for the rear doors, drill a hole through the regulator sector gear and backplate. Install the bolt and nut to lock the sector gear in position. Be careful not to drill a hole closer than 7/ 16 in. (11mm) from the edge of the sector. Also, do not drill through the lift arm attaching portion of the sector gear, or the joint integrity will be jeopardized. 3. Drill out the ends of the motor attaching rivets using a 1/ 4 in. (6mm) bit. 4. Remove the motor and the remaining portions of the rivets from the regulator. Except for the rear doors, one rivet will not be accessible until assembly. Regulator and motor assembly—except rear doors Secure the rivets by collapsing the rivet ends using a ball peen hammer To install: 5. Position the new motor to the regulator. With the aid of an assistant, install new rivets by collapsing or crushing the rivet ends using a ball peen hammer. 6. Except for the rear doors, once two of the three rivets have been installed, remove the bolt securing the sector gear to the backplate, then use an appropriate electrical source (such as the vehicle’s window motor harness) to rotate the regulator, providing access to the remaining rivet. 7. Except for the rear doors, use a flat nosed rotary file to grind off one sector gear tooth from the side which does not contact the driven gear. This is necessary to reach the remaining rivet. Remove the old rivet, then install the remaining new rivet. 8. Install the regulator to the door assembly.