torque spec ball joints chevy s10

You search PDF repair manual about torque spec ball joints chevy s10, if there are search results will appear below. If search results do not exist, please search by others keyword.



  torque spec ball joints chevy s10 Direct Download speed 5432 Kb/s

  torque spec ball joints chevy s10 Full Version speed 8172 Kb/s



1997 Ford F-250/ 350/ Super Duty Steering Knuckle REMOVAL AND INSTALLATION MANUAL

0

Filed Under (Ford Manuals) by admin on 13-06-2012

download
Steering Knuckle Removal 1. Remove the front wheel spindle (3105) and the right and left shaft and joint assembly. Refer to Spindle, RH and LH Shaft and Joint Assembly in the Removal and Installation portion of this section. 2. Disconnect the steering linkage, if necessary, from the knuckle. Refer to Section 11-03 in the Body, Chassis Manual. Steering Knuckle Installation 3. Remove the cotter pin from the stud of the front suspension upper ball joint (3049). Loosen the nut on the top stud and the bottom nut inside the steering knuckle. Remove the top nut. 4. Sharply hit the top stud with a plastic or rawhide hammer to free the knuckle from the axle arm. Remove and discard bottom nut. 5. NOTE: Note the orientation of the camber adjuster to make sure of the same camber setting. Remove camber adjuster by hand or, if difficulty is encountered, use Pitman Arm Puller T64P-3590-F. 6. Place steering knuckle in vise and remove snap ring from bottom ball joint socket if so equipped. 7. Remove plug from U-Joint Tool T74P-4635-C and replace with Plug T80T-3010-A4 (part of 4WD Ball Joint Tool Set T80T-3010-A). 8. Assemble U-Joint Tool T74P-4635-C and Receiving Cup T80T-3010-A2 (part of 4WD Ball Joint Tool Set T80T-3010-A). 9. NOTE: Always remove front suspension lower ball joint first. Turn forcing screw clockwise until front suspension lower ball joint is removed from steering knuckle. 10. Repeat procedure and remove front suspension upper ball joint. Installation 1. Clean steering knuckle bore and insert front suspension lower ball joint as straight as possible. 2. NOTE: If ball joint cannot be installed to the proper depth, realign Receiving Cup T80T-3010-A3. To replace the front suspension lower ball joint, assemble U-Joint Tool, Receiving Cup T80T-3010-A3 (part of 4WD Ball Joint Tool Set T80T-3010-A) and Installing Cup from Ball Joint Adapter Set D81T-3010-A or equivalent. 3. Turn forcing screw clockwise until front suspension lower ball joint is firmly seated. 4. Install the snap ring on the front suspension lower ball joint. 5. To install front suspension upper ball joint, assemble the C-Frame, Receiving Cup T80T-3010-A3 and Replacer T80T-3010-A1 (both part of 4WD Ball Joint Tool Set T80T-3010-A). 6. Turn forcing screw clockwise until front suspension upper ball joint is firmly seated. 7. Assemble knuckle to axle arm assembly. Install camber adjuster on the stud of the front suspension upper ball joint with the arrow pointing outboard for positive camber, pointed inboard for negative camber. 8. Install new nut on bottom socket finger-tight. Install and tighten nut on top socket finger-tight. Tighten bottom nut to 47 Nm (35 lb-ft). 9. CAUTION: If the tightening sequence is not followed in this step and Step 10, ball joint life will be reduced. NOTE: Do not loosen top nut to install cotter pin. Tighten top nut to 136 Nm (100 lb-ft), then advance nut until castellation aligns with cotter pin hole. Install cotter pin. 10. Retighten bottom nut to 123-149 Nm (91-110 lb-ft). 11. Install the front wheel spindle and the right and left shaft and joint assembly as described in this section. 12. Connect steering linkage, if necessary, to the knuckle. Refer to Section 11-03 in the Body, Chassis Manual.

Related Content:

removing trailblazer ball joints, 2004 dodge ram 1500 torque values front end ball joints swaybar links whjeels, oem ball joint press, torqe for ball joint 2001 prizm, peugeot 306 front lower arm removal, Is an alignment required after replacing lower ball joints on a 2008 chevrolet silverado?, how to replace the lower and upper ball joints ona 1995 dodge 1500 2 wheel dr at home with no lift, how to replace bal joint hyundat accent 2000, how to replace a balljoint on a 2002 buick lesabre, 08 silverado lower ball joint removal

2004-2008 FORD F150 FRONT LEVELING SYSTEM INSTALLATION MANUAL

0

Filed Under (Ford Manuals) by admin on 19-12-2011

download
Front End Installation: 1. To begin installation, block the rear tires of the vehicle so that the vehicle is stable and can’t roll backwards. Safely lift the front of the vehicle and support the frame with jack stands. Place jack stands on both the driver and the p sides of the vehicle. Next remove the wheel from both sides. assenger s 2. Remove the upper strut mounts with a 15-mm wrench or . m socket. Using a ball cket. Use an socket. You will need a socket to remove the far strut mount 3. Remove the sway bar lower link pin bolt from the bottom of the control arm with an 18 mm socket. 4. Disconnect the tie rod end with a 21 m peen hammer or impact tool, hit the steering knuckle (not the tie rod) until the tie rod pops out. If you use a tie rod pickle fork, be careful not to cut the tie rod boot. A severed tie rod boot will allow dirt and moisture to damage the tie rod end. 5. Remove the upper ball joint nut with a 21 mm so impact tool or ball peen hammer and hit the steering knuckle until the upper control arm pops out.
6. Support the knuckle with a bungee cord or safety wire so not to overextend the CV axel or stretch the brake hydraulic hose. 7. Next remove the struts lower bolt. Using a 27 mm wrench, hold the nut and remove the bolt with a 30 mm socket. 8. Remove the strut assembly. 9. Place the strut extension on the top of the strut, hold the part up to start the nuts onto the factory studs. ** Caution: Use the factory nuts with the factory studs** 10. Run down nuts snug with end wrench. Torque to OEM specs. 11. Place strut back into upper strut mount. Tighten provided nuts snug with wrench or ratchet (after install, you will torque to OEM specs). 12. Use a pry bar to position the lower control arm and the strut mount to reinstall the mounting bolt. Torque to OEM specs. 13. Place a jack under the lower control arm. Raise the lower control arm to reattach the ball joint. A pry bar may be used to hold the upper control arm into position. Torque the ball joint nut to OEM specs. 14. Reattach the tie rod end. Torque to OEM specs. 15. Reattach the sway bar. Torque to OEM specs. 16. Reattach the wheel. Torque to OEM specs. 17. Repeat on opposite side. 18. Lower vehicle to ground and torque strut mounts to OEM specs. 19. Align the vehicle. A certified alignment technician that is experienced with lifted vehicles is recommended to perform the alignment

Related Content:

2000 ford ranger transmission bolt torque specs, torgue spec on 2004 mazda3, 02 ford explorer driveworks front wheel hub torque, torque number sway bar ends 2002 lincoln ls, LOWER CONTROL ARMS TORQUE SPECS ON 2004 PACIFICA, lincoln ls 3 9l connecting rod bearing torque, idler arm torques, how many foot lbs torque on lower control arm bolt lincoln ls, ford e450 wheel torque, ford 4 0 sohc oil pan inserts torque specs

1999-2006 TOYOTA TUNDRA FRONT LEVELING SYSTEM FOR THE 6-LUG SUSPENSION INSTALLATION INSTRUCTIONS

0

Filed Under (Toyota Manuals) by admin on 04-12-2011

download
1. To begin installation, block the rear tires of the vehicle so that the vehicle is stable and can’t roll backwards. Safely lift the front of the vehicle and support the frame with jack stands. Place jack stands on both the driver and the passenger sides of the vehicle. Next remove the wheels from both sides. 2. Using a 17mm socket, remove the lower sway bar link bolt from both sides. HINT: If the stud turns together with the nut use a hex wrench or vice grips to hold the stud . 4. Next remove the strut’s lower mounting bolt with a 19 mm socket and wrench. NOTE: Once the nut is removed, it may be necessary to use a punch and hammer to free the bolt. 5. Remove the nuts from the three upper strut mounting bolts with a 14 mm ratchet. Be sure to support the strut assembly as the nuts are removed to prevent it from falling. 6. Remove the strut assembly from the vehicle and mount it in a bench vise. Install the steel strut extension on the top of the strut assembly. ** Caution: Use the factory nuts with the factory studs** 7. Run down nuts snug with end wrench. Torque to OEM specs. NOTE: Because of the shape of the steel spacer the strut will be rotated 180° when reinstalled. 8. Place strut back into upper strut mount. Tighten provided nuts snug with a 14mm wrench or ratchet (after install, you will torque to OEM specs). 9. Use a pry bar to position the lower control arm and the strut mount, and then reinstall the mounting bolt. Torque to OEM specs. 10. Place a jack under the lower control arm. Raise the lower control arm to reattach the lower ball joint bolts. Torque the ball joint nuts to OEM specs. 11. Repeat Steps 3 through 10 on the opposite side of the vehicle. 12. Reattach the sway bar link assembly on both sides of the vehicle. Torque to OEM specs. For 2wd trucks skip Step 13. 13. For 4×4 models only it is necessary to lower the differential using the provided spacers and bolts. Install the spacers following the instructions provided with the spacers. 14. Reattach the wheels. Torque to OEM specs. 15. Lower vehicle to the ground and torque strut mounts to OEM specs. 16. Align the vehicle. A certified alignment technician that is experienced with lifted vehicles is recommended to perform the alignment

Related Content:

2007 kia optima harmonic balancer bolt torque, volvo d13 flywheel torque spec, torque specs for 5 7 volvo penta exhaust manifold, torque specs 4 8 chevrolet, rod torque botyom end n14, ax4n pan bolt torque spec, 2006 chrysler 300 rocker torque specs 2 7, lug nut torque on isuzi, 2001 buick lesabre strut torque, cummins n14 torque specs

2007-2008 TOYOTA FJ CRUISER 2WD AND 4WD 3″ SUSPENSION LIFT KIT INSTALLATION INSTRUCTIONS

0

Filed Under (Toyota Manuals) by admin on 12-11-2011

download
4Runner/FJ Cruiser Installation Instructions 08/28/08 INST-431.DOC Page 2 of 5 FRONT OF 4RUNNER/FJ CRUISER 1. Park vehicle on level concrete surface. 2. Center and lock the steering wheel. 3. Block the rear wheels of the vehicle to prevent vehicle from moving in either direction. 4. Before lifting vehicle, remove rear shock absorbers and discard. 5. Jack up the vehicle from the lift point in Figure A. 6. Support the vehicle with jack stands from the points in Figure A. 7. Remove the front wheels. 8. Remove sway bar end links from spindle using 17mm socket (both sides). See Figure B. 9. Remove front skid plate using 12mm socket. 10. Remove sway bar from frame using 14mm socket. See Figure C. 11. Using 19mm socket, remove lower bolt and nut from the bottom of the strut (both sides). 12. Remove cotter key and 19mm nut from outer tie rod end, rack & pinion utilizing a tie rod end puller (or pickle fork). 13. Remove the three nuts (14mm) from the top of the strut. See Figure D. 14. Remove the struts from the vehicle, making sure that they are marked driver and passenger side respectively for reinstallation. NOTE: AT THIS TIME, IF YOU DO NOT HAVE A SUITABLE SPRING COMPRESSOR, IT IS HIGHLY ADVISED TO EITHER TAKE THE STRUT TO A QUALIFIED SERVICE CENTER OR PURCHASE THE REVTEK SC-1 SPRING COMPRESSOR. 15. Compress strut assembly and remove the nut (17mm) on the top of the strut shaft. 16. Release the compressor. 17. Remove the spring top plate from the strut. 18. Remove and discard the rubber spacer FRONT OF 4RUNNER/FJ CRUISER (continued) 19. Remove (hammer) the studs from the spring top plate. See Figure “F.” 20. Install (hammer) the LONGER STUDS (10MM) (provided) in the spring top plate. See Figure “G.” 21. Install the PRELOAD SPACER between the spring and the spring top plate with the small diameter facing toward the spring and the Revtek Industries logo facing outward. See Figure H. 22. Compress the strut assembly, making sure you center the strut shaft through the spring top plate hole and that the STUDS line up with the PRELOAD SPACER reliefs. Replace nut on the top of the strut shaft and torque to spec. (Torque specs can be found on page 1.) 23. Install the TOP OUT EXTENDER over the STUDS (Figure H). 24. Reinstall the strut by reversing the removal procedure; torque to spec. (Torque specs on page 1.) 25. When properly installed, Revtek Industries logo will be centered between preload spacer reliefs. 26. Reinstall tie rod ends, torque to spec. 27. Reinstall sway bar to frame. 28. Reinstall sway bar end links into spindles. Torque to spec. 29. Reinstall front skid plate. 30. Replace the wheels; torque to spec.

Related Content:

Volvo D13 engine bolt torques, 2002 PT Cruiser jacking points, 92 toyota pinion nut torque spec, how to remove torque converter bolts from a Volvo D13, removal of front struts Toyota FJ cruiser

Coil Spring Spacer Installation Instructions

0

Filed Under (More Manuals) by admin on 24-12-2011

download
1. Check to see that the spacer kit you purchased matches the year and model of your vehicle. Spacer kits two inches or taller may require a spring compressor to install. Ball joint and tie rod forks may also be useful. 2. A good portion of your front suspension will be disassembled so this would be a good time to replace any worn parts (i.e. tie rod ends, ball joints, idler arm and any bushings) Replace bushings with polyurethane replacement parts. 3. Jack up vehicle as high as possible using jack stands for support at all times. 4. With vehicle safely off the ground remove front tires. It is advisable to disassemble on side at a time so that you can use the other side as a reference for re-assembly in the event you get side tracked. 5. Remove the brake caliper from the rotor (attached with 2 bolts inside the caliper or with press-in clips depending on the vehicle). Do not remove the brake line from the caliper unless you intend to bleed the brakes at this time. Set the caliper aside or tie it up to the frame rail. Avoid pinching the brake line. 6. Remove the tie rod from the spindle using the proper tools. Do not hit the tie rod itself or the nut on the threaded portion of the tie rod or it may cause damaged and need replacing. 7. Remove the anti-sway bar from the lower control arm. This would be a good time to replace the end link bushings with polyurethane replacement bushings. 8. If your vehicle is equipped with anti-lock brakes you must now disconnect the front rotor sensor from the dust shield or spindle and set it aside. 9. Disconnect your shock absorber completely from the vehicle whether it is mounted inside the coil spring or not. 10. Support the lower control arm with jack just touching the arm. This will prevent it from dropping when the ball joint is disconnected. 11. The use of a coil spring compressor is recommended before the following steps are taken. 12. Disconnect the upper ball joint from the top of the spindle using the proper tools. Do not hit the ball joint or the threaded end of the ball joint. Once the ball joint is free the spindle should move easily. 13. Be careful when lowering the lower control arm. The coil spring is under high compression and may shoot out when released. Do not stand near the side of the truck during this step. Lower the jack so that the lower control arm swings down. If the coil spring has not fallen out on it’s own you may need to use a pry bar from the front of the vehicle to remove it. 14. Note which end of the coil spring is “bottom” for installation. Also note the depression in the lower control arm. It is important that the last winding of the coil spring fit into the indentation completely so that the vehicle will sit level. Do not switch coil springs from side to side as some vehicles have a specific “right” and “left” coil spring. 15. Check the coil spacer for proper fitment into the coil spring mount in the frame. The flat part of the spacer should face up and touch the top of the spring mount. Some vehicles have guiding tabs to center the coil spring in its top mount. These tabs may have become bent and need to be bent back to allow the spacer to properly fit in the mount. 16. Install the coil spring with the spacer on top of it. If used the coil spring compressor should still be on the spring in a compressed state. If it is not you may need to compress the spring before re-installing. Make sure the spacer is centered in the upper mount and the bottom of the spring is properly nested in the receptor groove on the lower control arm. If you are installing a two-inch or taller spacer you may need a spring compressor. Follow all safety rules when installing the coil spring as it will be under extreme compression. 17. Raise the lower control arm with a jack once the coil spring and spacer are properly lined up. Raise until the spindle is high enough to bolt on the upper ball joint. Before bolting on the upper ball joint make sure the brake caliper and brake line are where they need to be since some brake lines run inside the spindle and outside the coil spring. 18. With the upper ball joint tight and a cotter pin re-installed you may now remove the jack from under the lower control arm. 19. Assemble all of the components previously removed (sway bar with new polyurethane bushings, tie rod ends with polyurethane grease boot, brake caliper and anti-lock sensor). Don’t forget the shock with a new colored boot while it is off. 20. Repeat instructions for other side. 21. After properly installing both spacers you can install your front tires and lower vehicle back to the ground. 22. Your vehicle may sit too high at first because the suspension needs to settle. Carefully back the vehicle up and drive forward a few times using the brakes frequently. Park on level ground and check out your lift. 23. The vehicle will now require a front wheel alignment. Failure to do so may result in severe wear on your tires and may pull to one direction

Related Content:

1997 ford ranger coil spring spacer installation, 4L60E 3 4 Accumulator Assembly, how to replace rear coil spring on a buick rendezours, how to use evertough coil spring compressor, Jeep TJ coil spring perch, labor to replace control arms g6, metal clip on ow beam 2009 mazda 6, ranger coil spring replace, replace 2006 Impala control arm bushings, replacing rear springs for 2004 toyota sienna

Toyota Front Coil Spring Spacer Lift Kit Installation Manual

0

Filed Under (Toyota Manuals) by admin on 22-12-2011

download
INSTALLATION INSTRUCTIONS FRONT 1. Read complete instructions before beginning installation, the following special tools are recommended: Coil spring compressor, floor jack, ball joint separator, jack stands, bench vise, and metric hand tools. 2. Jack the vehicle in the center of the front cross member. 3. Support the vehicle by placing jack stands on the frame cross member so that the front tire/wheels are off the ground. 4. Remove the front tires/wheels. 5. Disconnect the sway bar end links and remove the upper ball joint cotter pin and nut. 6. Separate the upper ball joint from the spindle. (Using ball joint separator or a suitable tool, be careful NOT to damage the ball joint boot) 7. Remove upper strut tower nuts holding strut assembly to strut tower (3) on each side of vehicle. 8. Remove the lower strut bolt from the lower control arm and remove the strut assembly from the vehicle. (Note the direction of the bolt for reinstallation) 9. Compress the coil spring on the strut assembly with a suitable coil spring compressor so that the coil spring has about 3/8″ play in the strut and remove the upper strut isolator mount nut. 10. Remove the coil spring isolator from the upper strut mounting plate. 11. Replace the upper strut mounting plate studs with the supplied studs with a bench vise and a deep well socket. (3 on each side) 12. Reinstall the factory coil spring isolator to the upper strut mounting plate. 13. Reinstall the compressed coil spring onto the strut assembly and reattach the upper strut mount plate using the stock hardware. See diagram. Torque upper strut mounting plate nut to 18 foot-pounds. 14. Decompress the coil spring in the strut assembly. Make sure that the spring is seated correctly into the strut assembly alignment indentation at the bottom of the strut and the top isolator. 15. Slide the coil spring spacer onto the top of the strut assembly over the 10mm studs. 16. Install the strut assembly into the strut tower and start the upper three 10mm lock nuts. (Make sure that the bottom of the strut is aligned as well) 17. Install the lower strut bolt in the original position and torque to 100 foot- pounds. (Step 8) 18. Using the floor jack, raise the lower control arm and connect the upper ball joint on the upper control arm to the spindle. Torque nut to 80 ft lbs. and make sure that you replace the cotter pin. (Not supplied) 19. Install the front tires/wheels. 20. Lower the vehicle onto the ground and tighten the upper strut tower 10mm nuts. Torque to 35 foot-pounds. (3 on each side) 21. RETORQUE ALL BOLTS AFTER 500 MILES.

Related Content:

sienna manual powered struts open manually, how man ft lbs for cadilla dts strut, strut removal ford crown victoria 2010 instruction, how to install lift support struts on 2006 Toyota Sienna, How to install lift gate struts, how to change out hatch struts on a toyota sienna, change struts lincoln ls, honda pilot strut replacement, Front strut replacement 1997 Ford Thunderbird, ford torque strut bushing

2008 Honda Accord L4-2.4L Knuckle/ Hub Bearing Unit Replacement

0

Filed Under (Honda Manuals) by admin on 19-11-2011

download
Hub Bearing Unit Replacement 1. Raise the rear of the vehicle, and support it with safety stands in the proper locations. 2. Remove the wheel nuts, and the rear wheel. 3. Remove the brake hose mounting bolt (A). 4. Remove the brake caliper bracket mounting bolts (B), then remove the caliper assembly (C) from the knuckle. To prevent damage to the caliper assembly or brake hose, use a short piece of wire to hang the caliper assembly from the undercarriage. Do not twist the brake hose excessively. 5. Remove the two washers (A). NOTE: During installation, make sure the washers are installed between the brake caliper bracket and the knuckle. 6. Remove the rear brake disc. 7. Remove the hub bearing unit (A) and O-ring (B). 8. Check the hub bearing unit for damage and cracks. 9. Install the hub bearing unit in the reverse order of removal, and note these items: * Use a new O-ring on reassembly. * After installing the brake caliper, make sure the clearance between lower arm B and the parking brake cable is more than 5 mm (3/16 in.). * Before installing the brake disc, clean the mating surfaces of the hub bearing unit and the brake disc. * Before installing the wheel, clean the mating surfaces of the brake disc and the inside of the wheel. * Check the wheel alignment, and adjust it if necessary. Knuckle Replacement 1. Remove the hub bearing unit. 2. Remove the splash guard (A). 3. Remove the lock pin (A) from the upper arm ball joint, then remove the castle nut (B). NOTE: During installation, install the lock pin as shown after tightening the new nut. 4. Disconnect the upper arm ball joint from the knuckle using the ball joint remover. NOTE: * Be careful not to damage the ball joint boot when installing the remover. * During installation, to connect the ball joint, raise the suspension with a jack. 5. Remove the wheel speed sensor (A) from the knuckle. Do not disconnect the wheel speed sensor connector. 6. Remove the self-locking nut (A) while holding the joint pin (B) with a hex wrench (C), then disconnect the stabilizer link (D) from the knuckle, and remove the brake hose bracket (E). NOTE: Use a new self-locking nut during reassembly. 7. Remove the damper lower mounting bolt (F). NOTE: Use a new mounting bolt during reassembly. 8. Remove the control arm mounting self-locking nut (A) and washer (B). NOTE: Use a new self-locking nut during reassembly 9. Remove the lower arm mounting bolt (A), and the lower arm B mounting bolt (B), then remove the knuckle (C). NOTE: Use new mounting bolts during reassembly. 10. Install the knuckle in the reverse order of removal, and note these items: * First install all the components, and lightly tighten the bolts and nuts, then raise the suspension to load it with the vehicle’s weight before fully tightening to the specified torque values. * Be careful not to damage the ball joint boot when connecting the knuckle. * Before connecting the ball joint, degrease the threaded section and tapered portion of the ball joint pin, the ball joint connecting hole, and the threaded section and mating surface of the castle nut.

Related Content:

2008 F250 STEERING GEAR PITMAN ARM NUT SIZE, bearing retaining nut for a 2004 Trailblazer, brake caliper dust boot honda 2007 accord coupe

1995-2004 TOYOTA TACOMA 4 X 4 AND PRERUNNER 3″ SUSPENSION LIFT KIT INSTALLATION INSTRUCTIONS

0

Filed Under (Toyota Manuals) by admin on 29-02-2012

download
Tacoma 4WD & PreRunner Installation Instructions Page 3 of 7 09/09/08 INST-425F.DOC FRONT OF VEHICLE 1. Park vehicle on level concrete surface. 2. Center and lock the steering wheel. 3. Block the rear wheels of the vehicle to prevent vehicle from moving in either direction. 4. Jack up the vehicle from the lift point in Figure “A.” 5. Support the vehicle with jack stands from the points in Figure “A.” 6. Remove the front wheels. 7. Remove the nut (14mm) and the hardware from the anti-sway bar. See Figure “B.” 8. Remove the nut (19mm) and bolt (14mm) from the bottom of the strut. See Figure “C.” 9. Remove the three nuts (14mm) from the top of the strut. See Figure “D.” 10. Remove the strut from the vehicle. NOTE: AT THIS TIME, IF YOU DO NOT HAVE A SUITABLE SPRING COMPRESSOR, IT IS HIGHLY ADVISED TO EITHER TAKE THE STRUT TO A QUALIFIED SERVICE CENTER OR PURCHASE THE REVTEK SC-1 SPRING COMPRESSOR. 11. Compress strut assembly and remove the nut (17mm) on the top of the strut shaft in Figure “E.” 12. Release the compressor. 13. Remove the spring top plate from the strut. 14. Remove and discard the rubber spacer. 15. Remove (hammer) the studs from the spring top plate. See Figure “F.” 16. Install (hammer) the LONGER STUDS (10MM) (provided) in the spring top plate. See Figure “G.” 17. Install the PRELOAD SPACER between the spring and the spring top plate with the small diameter facing toward the spring. See Figure “H.” 18. Compress the strut assembly, making sure you center the strut shaft through the spring top plate hole and that the STUDS line up with the PRELOAD SPACER reliefs. Replace nut on the top of the strut shaft and torque to spec. (Figure “E”). (Torque specs can be found on page 1.) 19. Install the TOP OUT EXTENDER over the STUDS (Figure “H”). 20. Reinstall the strut by reversing the removal procedure; torque to spec. (Torque specs on page 1.) 21. When properly installed, PRELOAD SPACER relief and Revtek Industries logo should face outward. (Figure R) 22. Reinstall hardware and nut on anti-sway bar; torque to spec. 23. Replace the wheels; torque to spec.

Related Content:

TORQUESPECLINCOLN2000

2005-2008 TOYOTA TACOMA 4 X 4 AND PRE RUNNER 3″ SUSPENSION LIFT KIT INSTALLATION INSTRUCTIONS

0

Filed Under (Toyota Manuals) by admin on 31-03-2012

download
Tacoma Installation Instructions 09/09/08 INST-426A.DOC Page 2 of 7 FRONT OF TACOMA 1. Park vehicle on level concrete surface. 2. Center and lock the steering wheel. 3. Block the rear wheels of the vehicle to prevent vehicle from moving in either direction. 4. Jack up the vehicle from the lift point in Figure A. 5. Support the vehicle with jack stands from the points in Figure A. 6. Remove the front wheels. 7. Remove sway bar end links from spindle using 17mm socket (both sides). See Figure B. 8. Remove front skid plate using 12mm socket. 9. Remove sway bar from frame using 14mm socket. See Figure C. 10. Using 19mm socket, remove lower bolt and nut from the bottom of the strut (both sides). 11. Remove cotter key and 19mm nut from outer tie rod end, rack & pinion utilizing a tie rod end puller (or pickle fork). 12. Remove the three nuts (14mm) from the top of the strut. See Figure D. 13. Remove the struts from the vehicle, making sure that they are marked driver and passenger side respectively for reinstallation. NOTE: AT THIS TIME, IF YOU DO NOT HAVE A SUITABLE SPRING COMPRESSOR, IT IS HIGHLY ADVISED TO EITHER TAKE THE STRUT TO A QUALIFIED SERVICE CENTER OR PURCHASE THE REVTEK SC-1 SPRING COMPRESSOR. 14. Compress strut assembly and remove the nut (17mm) on the top of the strut shaft. 15. Release the compressor. 16. Remove the spring top plate from the strut. 17. Remove and discard the rubber spacer Tacoma Installation Instructions 09/09/08 INST-426A.DOC Page 3 of 7 FRONT OF TACOMA (continued) 18. Remove (hammer) the studs from the spring top plate. See Figure “F.” 19. Install (hammer) the LONGER STUDS (10MM) (provided) in the spring top plate. See Figure “G.” 20. Install the PRELOAD SPACER between the spring and the spring top plate with the small diameter facing toward the spring and the Revtek Industries logo facing outward. See Figure H. 21. Compress the strut assembly, making sure you center the strut shaft through the spring top plate hole and that the STUDS line up with the PRELOAD SPACER reliefs. Replace nut on the top of the strut shaft and torque to spec. (Torque specs can be found on page 1.) 22. Install the TOP OUT EXTENDER over the STUDS (Figure H). 23. Reinstall the strut by reversing the removal procedure; torque to spec. (Torque specs on page 1.) 24. When properly installed, Revtek Industries logo will be centered between preload spacer reliefs. 25. Reinstall tie rod ends, torque to spec. 26. Reinstall sway bar to frame. 27. Reinstall sway bar end links into spindles. Torque to spec

Related Content:

2005 tacoma shop manual free download, install rack and pinion 2006 tacoma, pdf how to replace 2003 prerunner steering knuckle, rack and pinion 99toyota tacoma install, skid plate install intructions for a 2014 toyota tacoma, torque specs for pressure plate 1997 tacoma 4x4, toyota avensis jacking points, toyota tacoma frame replacement procedures

1984-2002 Pontiac Camaro / Firebird ADJUSTABLE TORQUE ARM INSTALLATION MANUAL

0

Filed Under (Pontiac Manuals) by admin on 23-02-2012

download
Inspect the motor mounts and the transmission mount. Worn, weak or broken mounts will cause the torque arm to not function properly and can cause damage to your vehicle. Stock OE transmission mounts in Camaros and Firebirds are very weak and known to fail. If you have a broken or weak transmission mount, it will cause the torque arm to actually lift the tail end of the trans. up. This could cause severe wheel hop, driveline misalignment and possible damage to the transmission, drive shaft, u-joints, rear axle, torque arm, and/or floor pan of vehicle. We highly recommend using a good quality polyurethane transmission mount like Energy Suspension #33- 1108. Using the Energy Suspension transmission mount is good insurance that your transmission stay solid and the torque arm will work to its full potential. 2. Inspect the rear suspension bushings. We strongly recommend using either Edelbrock (#5274) lower trailing arms with a spherical ball on one end and polyurethane bushings on the other, Edelbrock (#5204) trailing arms with polyurethane bushings on both ends, or other high quality trailing arms that use high quality polyurethane bushings. We also recommend the use of an Edelbrock or other high quality panhard rod to replace the stock OE piece that uses sponge rubber bushings. The lower trailing arms and panhard rod secure the rear axle under the car. Upgrading to stronger high quality tubular trailing arms and panhard rod with polyurethane bushings will increase the overall strength, eliminate the sponge feel of rubber bushings and further increase the function potential of the torque arm. Worn out trailing arm or panhard rod bushings can contribute to or cause torque arm or other suspension component failures. Remember each suspension component

Related Content:

2008 CHEVY UPLANDER TRAIL ARM BUSHINGS, how to change rear bushing in 06 chevy uplander, mistubishi fuso 4d34 idle linkage, torque on pitman arm 99 crown vic

Related Content:

removing trailblazer ball joints, 2004 dodge ram 1500 torque values front end ball joints swaybar links whjeels, oem ball joint press, torqe for ball joint 2001 prizm, peugeot 306 front lower arm removal, Is an alignment required after replacing lower ball joints on a 2008 chevrolet silverado?, how to replace the lower and upper ball joints ona 1995 dodge 1500 2 wheel dr at home with no lift, how to replace bal joint hyundat accent 2000, how to replace a balljoint on a 2002 buick lesabre, 08 silverado lower ball joint removal