Skip to content

what size oil filter wrench 2011 toyota camry

You search PDF repair manual about what size oil filter wrench 2011 toyota camry, if there are search results will appear below. If search results do not exist, please search by others keyword.

Toyota Avalon, Camry, Camry Hybrid, Corolla, Highlander, Highlander CABIN AIR FILTER IDENTIFICATION / INSTALLATION MANUALHybrid, Matrix, Prius, RAV4, Sequoia, Tundra, Venza, Yaris

download
1. Open passenger side door. 2. Open glove compartment. 3. Remove screw holding damper rod in place on right side of glove compartment. 4. Detach damper rod from glove compartment. 5. Push in on left and right sides of glove compartment to release glove compartment. Filter Housing Cover 6. Flip down glove compartment. 7. Remove filter housing cover. Filter Housing Cover 8. Replace filter and reassemble

2007-2010 Toyota Camry Hybrid Vehicles Potential Floor Mat Interference with Accelerator Pedal

download
The owner notification will commence in early February, approximately one week after your dealership has been notified. This campaign will be launched in phases. • The first phase will include certain 2007 through 2010 model year Camry and Camry Hybrid vehicles equipped with Denso accelerator pedals. These owner letters will be mailed over a period of several weeks. • Additional models, including Camrys equipped with a CTS accelerator pedal will be launched in later phases as the remedy is developed. • Information on additional phases related to Camry (equipped with a CTS accelerator pedal), Avalon, Corolla, Highlander, Matrix, Prius, Tacoma, Tundra and Venza will be provided prior to the launch of these phases. If your dealership is contacted by an owner of a Denso pedal equipped Camry who has not yet received a notification, please verify eligibility by confirming through Dealer Daily/TIS prior to performing repairs . Dealers should perform the repair as outlined in the attached Technical Instructions. 2. Vehicles in Dealer Stock • As required by Federal law, dealers are not to deliver any new vehicles in their inventory, which are involved in a safety recall unless the defect has been remedied. However, because this defect does not exist in vehicles in which the driver’s side floor mat is compatible with the vehicle and properly secured you may continue to sell new vehicles (with Denso pedals) that have not received the full remedy if you assure the driver’s position floor mat is semi-permanently secured or place the front driver’s and passenger’s floor mats in the trunk on any vehicles in stock prior to sale or lease. Vehicle safety recall completion can be verified through TIS. • In order to assure established customers receive priority for the safety recall, we request that this campaign remedy be performed on in-stock Camry and Camry Hybrid vehicles just prior to vehicle delivery where possible. • A VIN list containing vehicles in dealer stock will be provided shortly

2004 Toyota Camry Disc Brake System Service/ Repair Manual

download
OVERHAUL HINT: Overhaul the RH side by the same procedures with LH side. REMOVE FRONT WHEEL 1. DRAIN BRAKE FLUID NOTICE: Wash off the brake fluid immediately if it comes into contact with a painted surface. 2. DISCONNECT FRONT FLEXIBLE HOSE 3. Remove the union bolt and a gasket from the disc brake cylinder, then disconnect the flexible hose from the disc brake cylinder. a. REMOVE DISC BRAKE CYLINDER ASSY FR LH 4. Remove the 2 bolts and disc brake cylinder. a. REMOVE DISC BRAKE PAD KIT FRONT (PAD ONLY) 5. Remove the 2 brake pads with anti-squeal shim. a. 6. Remove the 2 anti-squeal shims from each of 2 brake pads . a. Using a screwdriver, remove the wear indicator from each of 2 brake pads . b. REMOVE FRONT DISC BRAKE PAD SUPPORT PLATE 7. Remove the upper side front disc brake pad support plate. a. REMOVE FRONT DISC BRAKE PAD SUPPORT PLATE 8. Remove the bottom side front disc brake pad support plate. a. 10. Remove the cylinder slide bush from the cylinder slide pin. a. REMOVE FRONT DISC BRAKE BUSH DUST BOOT 11. Remove the 2 bush dust boots from the disc brake cylinder mounting. a. REMOVE FRONT DISC BRAKE CYLINDER MOUNTING LH 12. Remove the 2 bolts and disc brake cylinder mounting LH. a. 13. Using a screwdriver, remove the set ring and cylinder boot. a. REMOVE FRONT DISC BRAKE PISTON 14. Place a piece of cloth or similar, between the piston and the disc brake cylinder. a. Use compressed air to remove the piston from the disc brake cylinder. CAUTION: Do not place your fingers in front of the piston when using compressed air. NOTICE: Do not spatter the brake fluid . b. 2004 Toyota Camry L4-2.4L (2AZ-FE) REMOVE PISTON SEAL 15. Using a screwdriver, remove the piston seal from the disc brake cylinder. NOTICE: Do not damage the inner cylinder and the cylinder groove. a. REMOVE FRONT DISC BRAKE BLEEDER PLUG CAP 16. REMOVE FRONT DISC BRAKE BLEEDER PLUG 17. INSPECT BRAKE CYLINDER AND PISTON Check the cylinder bore and piston for rust and scoring 18.

2007 TOYOTA TUNDRA COLD AIR INTAKE Preparation

download
1. Check Box Contents (a) Check box for contents and/or damage. 2. Vehicle Preparation (a) Open vehicle hood. (b) Use blankets or covers to protect the front grille and passenger-side front fender area. Note: For 5.7L installation proceed to next step. For 4.7L installation proceed to step #4 3. Removal Procedure: 5.7L V8 OE Air Inlet System (a) Raise the front of the engine cover to detach the 2 pins (Fig. 3-1). (b) Remove the 2 engine cover hooks from the bracket, and remove the cover (Fig. 3-1). (c) Disconnect the vacuum hose and ventilation hose (Fig. 3-2). (d) Loosen the two 10 mm hose clamps and remove the air cleaner hose (Fig. 3-2). 12 mm Wrench Fig. 3-1 Fig TOYOTA TUNDRA 2007 – COLD AIR INTAKE Procedure Page 3 of 15 pages Issue: A 08/24/07 10mm Socket 10 mm Socket 10 mm Socket 4. Removal Procedure: 4.7L V8 OE Air Inlet System (a) Remove the two 10 mm cap nuts and throttle body cover (Fig. 4-1). (b) Remove air cleaner hose assembly. (1) Disconnect the vacuum hose and No. 2 ventilation hose (Fig. 4-2). (2) Loosen the two 10 mm hose clamps and remove the air cleaner hose (Fig. 4-2). 5. Removal Procedure: 5.7L and 4.7L V8 OE Air Inlet System (a) Remove the air cleaner lid. (1) Disconnect the MAF sensor connector (Fig. 5-1). (2) Using a clip remover, detach the wire harness clamp (Fig. 5-1). (3) Unfasten the 4 hook clamps and then remove the air cleaner lid (Fig. 5-1). (b) Remove OE air filter and save. (c) Remove the two 10 mm bolts and air cleaner case (Fig. 5-2)

Burien Toyota 5SFE Turbo Installation Instructions

download
The following parts are not required, but you may want to have on hand: 9 Fresh Toyota engine coolant 9 New engine oil (preferably synthetic) and new Toyota oil filter 9 New parts to perform a tune-up (spark plugs, distributor cap & rotor). If you do replace your plugs, you may want to use a colder plug to reduce the chance of detonation. 9 New Ignition wires, if your current wires are old 9 New Toyota fuel filter (since you’re replacing the expensive injectors) 9 Shorter oil filter union from Toyota (See step #11) 9 Tie-wraps to secure vacuum lines (See step #27) 9 Shielded audio cable (See step #26.b) 9 For automatic transmissions, consider replacing the transmission fluid with a good synthetic brand and installing an ATF cooler. Burien Toyota 5S-FE Turbocharger Installation Manual Page 2 of 20Kit Contents ¾ Toyomoto exhaust manifold ¾ Garrett TB0344 turbo (Exhaust manifold and turbo charger come attached) ¾ Intermediate pipe (‘S’ shaped pipe with blow off valve attached) ¾ Down pipe (‘J’ shaped pipe with 90° bend and exhaust flange, also has mount for oxygen sensor) ¾ Turbo intake pipe (Usually attached to turbo) ¾ 90º elbow with valve cover breather hose attached (Elbow used to mount air filter) ¾ K&N air filter ¾ HKS Racing Blow-off/Pop-off valve ¾ (4) 360cc Toyota Injectors ¾ Toyota Oil pan ¾ Toyota MAP Sensor ¾ All necessary hoses, clamps, nuts, bolts, fittings, studs, gaskets and such required to install the system.