Skip to content

what type of fluid in a chevy trailblazer front differential 2005

You search PDF repair manual about what type of fluid in a chevy trailblazer front differential 2005, if there are search results will appear below. If search results do not exist, please search by others keyword.

1997-2005 Ford Expedition REAR AXLE NOISE REPAIR MANUAL

download
5L3Z-4209-F = (9.75-Inch Ring Gear/3.73 ratio) •205-506 – Seal Protectors (Rotunda Tool) (1997-2005 F-150, 1997-2005 •W710084-S439 – Wheel End Nuts Expedition/Navigator) •390266-S100 – Differential Slave Pin Bolt (9.75? axles) NOTE 9.75 REAR AXLE HOUSINGS WERE •387426-S100 – Differential Slave Pin Bolt (8.8? REDESIGNED IN MID-1999, INCREASING FRONT axles) PINION BEARING SIZE. REPLACING RING & •4B422 – Axle Circlips PINIONS IN AN OLD-STYLE AXLE ASSEMBLY •ZC-21 – Metal Surface Cleaner WILL REQUIRE INSTALLATION OF SPACER P/N •TA-29 – Ultra Silicone Sealant YL3Z-4662-CA. SPACER IS TO BE INSTALLED BETWEEN INNER PINION BEARING AND •TA-27 – Stud and Bearing Mount Retaining COLLAPSIBLE SPACER. Compound and Sealer •F3TZ-4121-AA – Fluid Tag (REQUIRED IF FLUID THE AXLE SERVICE KITS INCLUDE THE TYPE IS CHANGED FROM FEHP DURING FOLLOWING COMPONENTS: REPAIR) •4630 – Head Bearing WARRANTY STATUS: Eligible Under Provisions Of •4628 – Head Bearing Cup New Vehicle Limited •4676 – Pinion Seal Warranty Coverage •386989-S2 – Washer (Slinger) OPERATION DESCRIPTION TIME •4621 – Tail Bearing 052303A 1997-2002 Expedition, 4.7 Hrs. 1998-2002 Navigator, •4616 – Tail Bearing Cup 1997-2004 F-150 Heritage, •4222 – Differential Bearing Cups 2004-2005 F-150: Rear •4221 – Differential Bearings Axle Noise Repair •4209 – Gear Set (includes pinion shims, pinion (Includes Time For Road nut and crush spacer) Test To Verify Concern (Beam Axle)) (Do Not Use •4209 – Instruction Sheet With 4205A Or 4205A4) NOTE 052303A 2003-2005 Expedition: 5.8 Hrs. THE KIT DOES NOT INCLUDE THE FOLLOWING Rear Axle Noise Repair ITEMS. SOME OR ALL OF THESE ITEMS WILL (Includes Time For Road BE REQUIRED TO COMPLETE THE AXLE Test To Verify Concern (Irs SERVICE, DEPENDING ON AXLE Axle)) (Do Not Use With APPLICATION/STYLE. 4010D Or 4010D4) 052303A 2003-2005 5.9 Hrs. ORDER AS NEEDED:

1997-2001 HONDA CR-V (4WD) Noise From the Rear Differential REPAIR PROCEDURE

download
REPAIR PROCEDURE 1. Drain and refill the rear differential with Dual Pump Fluid. 2. Check the tires for proper inflation (recommended cold inflation front and rear is 26 psi) and any variation in tire size or type. 3. Test-drive the vehicle in a parking lot. Make tight, low-speed turns. If the noise is eliminated, return the vehicle to the customer. If the noise is still present, go to step 4. 4. Remove the rear differential assembly (see page 15-16 of the 1997-01 CR-V Service Manual). 5. Remove the torque control differential case, then remove and discard the 30 mm shim and the clutch assembly (see steps 1 thru 10 on pages 15-20 thru 15-22 of the service manual). 6. Remove the thrust needle bearing, the oil pump driveshaft, and the oil pump body assembly (see steps 11 and 12 on page 15-22 of the service manual). 7. Install the new flow collar over the drive pinion shaft. Make sure the tabs of the flow collar align with the oil pump pin. 8. For 1997 models: Assemble the new oil pump (spring, O-rings, piston, and pump body assembly). 9. Align the rear oil pump grooves with the oil pump pin and the flow collar tabs, then install the oil pump body assembly on the differential carrier. 10. Tighten the oil pump body assembly bolts to 12 N·m (8.7 lb-ft). 11. Align the oil pump driveshaft tabs with the grooves of the front oil pump in the oil pump body assembly, then install the oil pump driveshaft. 12. Install the thrust needle bearing with the outer race facing up.

2009 Toyota Corolla AXLE AND DIFFERENTIAL: FRONT AXLE HUB: INSTALLATION MANUAL

download
INSTALLATION 1. INSTALL FRONT AXLE HUB BEARING 2. INSTALL FRONT DISC BRAKE DUST COVER (a) Install the disc brake dust cover to the steering knuckle with the 3 bolts. Torque: 8.3 N·m (85 kgf·cm, 73 in·lbf) 3. INSTALL FRONT AXLE HUB SUB-ASSEMBLY 4. INSTALL FRONT AXLE HUB HOLE SNAP RING Last Modified: 4-24-2008 5.1 A From: 200712 Model Year: 2009 Model: Corolla Doc ID: RM000001IWX00ZX Title: AXLE AND DIFFERENTIAL: FRONT AXLE HUB: INSTALLATION (2009 Corolla) (a) Using SST and a press, install a new front axle hub bearing to the steering knuckle. SST: 09950-60020 09951-00720 SST: 09950-70010 09951-07100 (a) Using SST and a press, install the front axle hub sub-assembly. SST: 09608-32010 SST: 09950-60010 09951-00600 SST: 09950-70010 09951-07100 5. INSTALL FRONT LOWER BALL JOINT 6. INSTALL FRONT AXLE ASSEMBLY 7. INSTALL FRONT LOWER SUSPENSION ARM 8. INSTALL TIE ROD END SUB-ASSEMBLY 9. INSTALL FRONT DISC 10. INSTALL FRONT DISC BRAKE CALIPER ASSEMBLY 11. TEMPORARILY INSTALL FRONT AXLE HUB NUT (a) Using snap ring pliers, install a new front axle hub hole snap ring. (a) Align the matchmarks and install the front drive shaft assembly to the front axle hub sub-assembly. (b) Install the front axle assembly to the front shock absorber with the 2 bolts and the 2 nuts. Torque: 240 N·m (2448 kgf·cm, 176 ft·lbf) Be careful not to damage the drive shaft boot or speed sensor rotor. Page 2of 4

2004-2005 FORD F-150 FRONT BRAKE ROUGHNESS/ SHUDDER WHILE BRAKING REPAIR MANUAL

download
ISSUE b. If new level (47 fin) rotors are present, Some 2004/2005 F-150 vehicles built before perform one (1) of the following: 11/29/2004 may exhibit front brake roughness and or shudder while braking. (1) If rotors are within minimum thickness specifications, machine the rotors using ACTION the Rotunda on vehicle brake lathe and Service the rack and pinion, rotors, and caliper the Rotunda adapter kit 201-R0093. assemblies as needed, based on vehicle build date Refer to the Workshop Manual, Section and current part levels installed on the vehicle. 206-00 for the correct on-vehicle brake Refer to the following Service Procedure. lathe procedure. SERVICE PROCEDURE (2) If rotors are beyond machinable thickness, the front rotors must be 1. Vehicles built prior to 8/20/2003 require the replaced. replacement of the rack and pinion assembly if it has not been replaced. Refer to Workshop 3. Install new service fix calipers. Manual, Section 206-03 and 211-02. NOTE 2. Determine if the vehicle has the old or new REPLACE CALIPERS WITH NEW SERVICE FIX level rotors (Figure 1). CALIPER ASSEMBLIES BY REMOVING THE CALIPERS AT THE KNUCKLES. THE SERVICE REPLACEMENT CALIPERS WILL BE PRE-ASSEMBLED WITH ANCHOR, SPRINGS, AND PADS. THE CALIPERS SHOULD BE INSTALLED AS A UNIT WITHOUT DISASSEMBLY. PART NUMBER PART NAME 6L3Z-2B120-A Caliper Asy (Right Side) 6L3Z-2B121-A Caliper Asy (Left Side) 5L3Z-1102-AB Rotor (4X2, 6 Lug) 5L3Z-1102-BA Rotor (4X2, 7 Lug) 5L3Z-1125-AA Rotor (4X4, 6 Lug) 5L3Z-1125-BA Rotor (4X4, 7 Lug) 6L3Z-3504-AA Steering Gear (Super Cab/Crew 4X2) 6L3Z-3504-BA Steering Gear (Super Cab/Crew 4X4) Figure 1 – Article 05-21-19 6L3Z-3504-CA Steering Gear (Regular Cab 4X2) 6L3Z-3504-DA Steering Gear (Regular Cab 4X4) a. If old level rotors, replace the front rotors 6L3Z-3C294-AA Retainer Spindle Nut and front caliper assemblies. Refer to Workshop Manual, Section 206-00 for front rotor and caliper replacement.

2005-2007 Ford F-Super Duty STEERING WHEEL OSCILLATION REPAIR MANUAL

download
This article supersedes TSB 07-5-7 to update the NOTE Parts. SETTING TIRE PRESSURE TO DOOR SPECIFICATION IS ONE OF THE SINGLE MOST ISSUE IMPORTANT MEASURES IN RESOLVING THIS Some 2005-2007 F-Super Duty vehicles may exhibit ISSUE. LOWERING TIRE PRESSURE WILL MAKE steering wheel oscillation (back and forth motion), THIS ISSUE WORSE. immediately following front or rear wheel impacts ROAD TEST (i.e. pavement joints, frost heaves, rough roads, etc.). Steering wheel motion is typically in the range 1. Ask customer what type of road surface and of ± 5 degrees, and typically dampens out in fewer speed generates the steering wheel oscillation. than five oscillations. This condition occurs mostly on F-250/F-350 4X4 vehicles, and is more evident 2. Road test vehicle on similar road surface and on trucks equipped with a gas engine. speed, to gain a feel for the customer’s issue. ACTION 3. If no issues are identified during the road test, do not proceed with the rest of this TSB. Refer to the following Service Procedure to minimize the steering wheel oscillations on impacts, STEERING DAMPER however, there may be some remaining minor INSPECTION/REPLACEMENT AND oscillation which would be considered normal. STEERING/SUSPENSION FASTENER TORQUE CHECK SERVICE PROCEDURE SUMMARY F-250/F-350 4X4 Applications: 1. Set tire pressure and road test vehicle to evaluate vehicle before proceeding with further 1. Remove existing steering damper and frame repairs. If issue is resolved, do not proceed attachment bracket. with the rest of this TSB. 2. Replace steering damper and frame mounting 2. If concern still exists, install a new steering bracket with steering damper and frame damper (frame-mounted bracket and steering bracket. damper assembly on F-250/F-350 4X4 applications only). For F-250/F-350 4X2 and all 3. Attach steering damper to frame bracket and F-450/F-550 applications, inspect damper for torque bolt to 76 lb-ft (103 N•m). leaks and replace if necessary, torque steering 4. Assemble bracket and shock assembly to the and suspension fasteners per Workshop frame with attachment bolt retainer pointing to Manual (WSM). rear of vehicle. Torque frame bracket nuts to 59 3. If concern still exists, check front alignment and lb-ft (80 N•m). reduce front caster. 5. Attach other end of shock to the steering drag 4. Replace redundant control steering wheel (if link and torque to 66 lb-ft (90 N•m). equipped and vehicle built prior to 10/8/2004). 6. Install damper bolt cap to assure a friendly VEHICLE INSPECTION – TIRE PRESSURE surface for the battery cable in case of casual contact. 1. Set tire pressures as indicated on the vehicle label (located on driver’s door label).