Skip to content

which fuse is for the license plate light buick

You search PDF repair manual about which fuse is for the license plate light buick, if there are search results will appear below. If search results do not exist, please search by others keyword.

2005 Chevrolet Colorado Pickup SES Light Due to DTCs P0105, P0106, and/ or P0506 – Clean Throttle Body

download
Models: 2004-2007 Buick Rainier 2002-2007 Chevrolet TrailBlazer 2004-2007 Chevrolet Colorado 2002-2007 GMC Envoy 2004-2007 GMC Canyon 2002-2004 Oldsmobile Bravada 2006-2007 HUMMER H3 2005-2007 Saab 9-7X with any of the following engines: 2.8L (VIN 8 – RPO LK5) 2.9L (VIN 9 – RPO LLV) 3.5L (VIN 6 – RPO L52) 3.7L (VIN E – RPO LLR) 4.2L (VIN S – RPO LL8) The following diagnosis might be helpful if the vehicle exhibits the symptom(s) described in this PI. Condition/Concern: On rare occasions, a SES light may be experienced due to DTCs P0105, P0106, and/or P0506. There may or may not be an idle complaint accompanying the SES light. This may be due to excessive carbon build up in the throttle body. Recommendation/Instructions: If the SI diagnostics do not isolate a cause for this concern, clean the throttle body bore and plate for evaluation.

4T65E Transmission 1-2 Shift Shudder at Light to Moderate Acceleration (Replace Complete Second Clutch Assembly)

download
2001-2004 Buick Regal 2001-2005 Buick Century, LeSabre 2002-2007 Buick Rendezvous 2005-2007 Buick Terraza, LaCrosse, Allure (Canada Only) 2006-2007 Buick Lucerne 2001-2005 Chevrolet Venture 2001-2007 Chevrolet Impala, Monte Carlo 2005-2007 Chevrolet Uplander 2006-2007 Chevrolet Malibu SS, Malibu Maxx SS 2001-2002 Oldsmobile Intrigue 2001-2003 Oldsmobile Aurora 2001-2004 Oldsmobile Silhouette 2001-2005 Pontiac Aztek, Bonneville, Montana 2001-2007 Pontiac Grand Prix 2005-2007 Pontiac Montana SV6 2006-2007 Pontiac G6 GTP 2005-2007 Saturn Relay with 4T65E Automatic Transmission this service kit contains: Second Clutch Housing Fluid Seal Rings (613), a Second Clutch Assembly (617), a Case Cover (Channel Plate) Upper Gasket (430), and a Case Cover (Channel Plate) Lower Gasket (429). In addition to the content of this service kit, four other gaskets not included in this service kit will also be needed to complete the repair, a Control Valve Body Cover (Side Cover) Gasket (54), a Control Valve Body Cover (Side Cover) Inner Gasket (59), a Case Cover Lower Gasket (429), and a Case Cover Upper Gasket (430). These gaskets can be obtained by ordering service kit P/Ns 24206959 and 24206391. Be sure to use ONLY the Second Clutch Assembly and Second Clutch Housing Fluid Seal Rings provided in this service kit. DISCARD the Second Clutch Assembly and Second Clutch Housing Fluid Seal Rings removed from the transmission being serviced. Disassemble ONLY the Oil Pump Assembly from the Case Cover (Complete). DO NOT disassemble the Control Valve Body from the Case Cover. Remove ONLY the Case Cover-to- Case bolts to remove the Case Cover and Valve Body from Transmission Case AS AN ASSEMBLY . To access all Case Cover-to-Case bolts, it is necessary to remove the Pressure Control Solenoid Valve Assembly (322), and 1-2 & 3-4 Shift Solenoid Valve Assemblies (315A, 315B).

1999 Buick Regal DTC B1001 Option Configuration Error Repair Manual

download
Test Description The number(s) below refer to the step number(s) on the diagnostic table. 2. This step checks to see if the correct VIN is programmed in the powertrain control module (PCM). 4. This step checks to see if the body control module (BCM) has been replaced. 5. This step explains the proper steps to perform after a BCM has been replaced in order for the <- Back Forward -> Document ID# 385021 1999 Buick Regal Print BCM to operate properly. 6. This step checks to see if the correct VIN is programmed in the BCM. 7. This step explains how to properly program the VIN into the BCM. DTC B1001 Option Configuration Error Step Action Value (s) Yes No 1 Was the SIR Diagnostic System Check performed? — Go to Step 2 Go to SIR Diagnostic System Check 2 1. Install the scan tool. 2. Use the scan tool to verify that the PCM is programmed with the correct VIN by comparing the VIN that is stored in the PCM to the VIN plate of the vehicle. Is the PCM programmed with the correct VIN? — Go to Step 4 Go to Step 3 3 Use the scan tool and/or the techline machine to program the correct VIN into the PCM. Is the programming procedure complete? — Go to Step 9 — 4 Was the BCM replaced? — Go to Step 5 Go to Step 6 5 1. Use the F2 function key and follow the instructions on the scan tool under the BCM SPECIAL FUNCTIONS to reprogram the BCM. This allows the BCM to learn the Restraints ID from the SDM and also to learn other important data that is required. 2. Use the F6 function key and follow the instructions on the scan tool under the BCM SPECIAL FUNCTIONS to program the correct VIN into the BCM. 3. Use the techline machine to perform the theft relearn procedures for the replacement BCM. Are the programming procedures complete? — Go to Step 9 — 6 Use the scan tool to verify that the BCM is programmed with the correct VIN by comparing the VIN that is stored in the BCM to the VIN that is stored in the PCM. Is the BCM programmed with the correct VIN? — Go to Step 8 Go to Step 7 7 Use the F6 function key and follow the instructions on the scan tool under the BCM SPECIAL FUNCTIONS to program the correct VIN into the BCM. Is the reprogramming procedure complete? — Go to Step 9 — 1. Turn the ignition switch to the OFF position. 2. Replace the SDM. Refer to Inflatable Restraint

1994 Ford Mercury Cougar XR7 INTERIOR FUSE PANEL IDENTIFICATION/ INSTALLATION MANUAL

download
1 – 10 Amp Panel Dimmer, Parking/License Lights, Autoshock Module, Clock 2 – 10 Amp Air Bag Module 3 – 5 Amp Foglight Switch 4 – 10 Amp A/C Clutch 5 – 15 Amp HEGO 1 & 2 (V6 Only) 6 – 10 Amp Anti-Theft, Trunk, Map, Vanity, Glove Box, Underhood, L/H Instrument Panel, Rear Courtesy, Door Courtesy, Lock Cylinder & Dome Lights, Power Mirrors 7 – 10 Amp Turn Signal Indicators/Lights, Backup Lights 8 – 5 Amp Cluster, Rear Defrost Switch, Coolant/Wash Level Sensor, DRL Module, EVO Test, EVO Steering Sensor, ARC (EVO) Module, ARC Switch, Hard Relay, Soft Relay, Auto Mirror, EATC Blend Door, Airbag Module, Overdrive Cancel Switch, Brakeshift Solenoid 9 – 10 Amp Main ABS Relay, ABS Module UNDERHOOD FUSE PANEL IDENTIFICATION (1994 MODELS) The “high-current” fuse panel is located in the engine compartment on the L/H fender apron. Fig. 5: Underhood Fuse Panel Identification (1994 -95 Models) Courtesy of FORD MOTOR CO. Fuse & Relay Identification 1 – 15 Amp DRL Module, Foglights 2 – 5 Amp Memory 3 – 20 Amp Ignition Coil 4 – 20 Amp Auto Shock WARNING: Always disconnect battery ground cable before servicing “high-current fuses. It is recommended that “high-current” fuses be replaced by a qualified technician. 1994 Mercury Cougar XR7 FUSES & CIRCUIT BREAKERS 1989-95 FUSES & CIRCUIT BREAKERS Ford Motor Co. Virtual Wrench

TOYOTA PRIUS FOG LIGHT KIT INSTALLATION INSTRUCTIONS

download
Remove the negative battery terminal Installation 1. Secure the relay to the next to the fuse block with wire ties 2. Attach the ring terminal with 2 black wires to ground 3. Attach fog light 12v red wire to open spade inside the fuse block as shown in picture 1 Picture 1 4. Locate the large vehicle harness grommet on the left side. Cut the auxiliary wiring access nipple off the grommet and push small 2-wire connector through firewall. Note: Extra caution should be taken not to damage connector 5. Run wires along the driver side of the engine compartment. Secure with wire ties as needed 6. From inside the cabin remove dash panels and locate the little small connector that was pushed through in step 4. Plug it to the switch harness. 7. T-tap orange/black wire from fog light harness to connector 2C pin 32 green wire. Pin 32 is on the left side of the connector 7th pin up from bottom of the connector. Connector 2C located left of the steering column above big white wire picture 2 Picture 2 8. T-Tap green/black wire from fog light harness to connector L47 pin 11, pink wire (it is the last pin to the left). Connector L47 is on the steering column and plugs into the headlight control arm picture 3 Picture 3 9. Mount switch into switch knockout of dash (picture 4) FOG LIGHT KIT INSTALLATION INSTRUCTIONS TPR-301 TOYOTA PRIUS 2010+ Picture 4 10. Install switch harness 11. Reinstall dash panels 12. Route the fog light wire under car. 13. Remove fog light cover plates and lower splash shields 14. Mount fog lights into bezel by sliding fog light tabs into slots and secure other side with supplied screw (see picture 5) Picture 5 15. Install both fog light bezels 16. Plug in left side fog light into harness plug 17. Run right fog light wire harness and plug into right fog light. Secure with wire ties 18. Reattach the lower splash shields