Skip to content

window bracket for 2001 highlander front door

You search PDF repair manual about window bracket for 2001 highlander front door, if there are search results will appear below. If search results do not exist, please search by others keyword.

2001 Toyota Highlander Sport Utility, Radio, FRONT DOOR SPEAKER INSTALLATION MANUAL

download
2001 Toyota Highlander Sport Utility PRELIMINARY: Disconnect the negative battery cable. ANTENNA: The factory antenna is located atop the right front fender panel. RADIO REMOVAL AND IN-DASH INSTALLATION: Note: The factory radio provision is for a Double ISO/DIN style radio. An installation kit is required when installing an aftermarket stereo. 1. Using panel removal tool carefully pry off radio bezel. 2. Extract (6) 10 mm bolts securing radio and climate controls in dash, disconnect and remove. 3. Extract (8) Iso screws securing radio to bracket. 4. Extract (2) Philips screws securing bracket to bezel, pull away and remove radio. FRONT DOOR SPEAKER INSTALLATION: Note: The factory speaker provision is for a 1 ½” tweeter and a 6 ½” 3-Hole speaker mounted to a factory speaker adapter. 1. Remove screw cover from door opener cup and exract (1) Philips head screw, pry bezel out then forward to remove. 2. Remove inside mirror cover. 3. Pry out door cup and extract (1) Philips screw from beneath. 4. Exract (1) plastic fastener from front top portion of door. 5. Pry off door panel, pull away, disconnect, and remove. 6. Extract (3) 10 mm bolts securing speaker, pull away, disconnect, and remove. REAR DOOR SPEAKER INSTALLATION: Note: The factory speaker provision is for a 5 ¼” 3-Hole speaker mounted in a factory speaker adapter. 1. Remove screw cover from door opener cup and extract (1) Philips head screw, pry bezel out then forward to remove. 2. Pry out door cup and extract (1) Philips screw from beneath. 3. Pry off door panel, pull away, disconnect and remove. 4. Extract (3) 10 mm bolts securing speaker , pull away, disconnect, and remove

2001 Mazda Truck MPV FRONT DOOR DISASSEMBLY/ ASSEMBLY

download
1. Lower or raise the front door glass so that the distance from the top of the front door glass at the rear end to the upper part of the front molding is 185 mm {7.3 in} 2. Disconnect the negative battery cable. 3. Remove the front door trim 4. Disassemble in the order indicated below. 1. Inner handle 2. Front door trim bracket 3. Door screen 4. Front door glass 5. Front manual window regulator 6. Front power window regulator 7. Glass run channel 8. Front door lock 9. Outer handle 10. Door key cylinder 11. Door weatherstrip 12. Door lower weatherstrip 5. Assemble in the reverse order of disassembly Front Door Glass Disassembly Note 1. Remove the front door glass installation bolts. 2. Slant the front door glass as shown, and remove the front door glass from the inside of the front door. Outer Handle Assembly Note 1. Connect the door key cylinder harness of outer handle as shown

2006 Honda CR-V EX FRONT DOOR PANEL REMOVAL/ INSTALLATION MANUAL

download
FRONT DOOR PANEL REMOVAL/INSTALLATION Special Tools Required * Trim pad remover, Snap-on A 177A or equivalent, commercially available * KTC trim tool set SOJATP2014 1. Using a trim tool, pry out the upper portion of the cover (A) to release the hooks (B), then remove the cover. 2. Remove the screws. 3. Driver’s door: Pull the inner handle (A) rearward and out half-way to release the power door lock switch bracket (B) from the door panel (C). Fig. 7: Pulling Inner Handle – Driver Door Courtesy of AMERICAN HONDA MOTOR CO., INC. 4. Passenger’s door: Pull the inner handle (A) halfway. Fig. 8: Pulling Inner Handle – Passenger Door Courtesy of AMERICAN HONDA MOTOR CO., INC. 5. Driver’s door: Disconnect the power door lock switch connector (A). Disconnect the inner handle rod (B), then remove the inner handle (C). Fig. 9: Disconnecting Power Door Lock Switch Connector – Driver Door Courtesy of AMERICAN HONDA MOTOR CO., INC. 6. Lower the glass fully. 7. Remove the screws from under the armrest. Fig. 10: Removing Screws From Under Armrest Courtesy of AMERICAN HONDA MOTOR CO., INC. 8. Passenger’s door: Remove the switch panel (A). * 1 Insert a flat-tip screwdriver wrapped with protective tape through a hole under the armrest, and push up the back of the panel to release the rear hook (B). * 2 Pull out along the edge of the panel to release the hooks (C) and clip. * 3 Disconnect the power window switch connector (D). Fig. 11: Disconnecting Power Window Switch Connector Courtesy of AMERICAN HONDA MOTOR CO., INC. 9. Remove the mirror mount cover (see step 2 on POWER MIRROR REPLACEMENT ). 10. Remove the door panel (A) with as little bending as possible to avoid creasing or breaking it. * 1 Release the clip (B). * 2 Release the clips (C) that hold the door panel with a commercially available trim pad remover (D).

2001-2007 Toyota Highlander MOUNTING BRACKET KIT INSTALLATION INSTRUCTIONS

download
This bracket kit fits the 2001-10 Toyota Highlander. For the ’01-’07 Toyota Highlander, follow the instructions below. For ’08-’10 Toyota Highlander instructions, see the separate section included in these instructions. Important: please use all supplied bolts and parts and read all instructions carefully before beginning this installation. The majority of questions you may have can be answered within the text, and proper installation will ensure safe and secure travel. Now, begin the installation. Fig.C Fig.D Fig.E 1. Start by removing four plastic fasteners that attach the grille to the core support (Fig.C). 2. Once all the fasteners are removed, squeeze and push out a square plastic clip fastener for the grille, located between the headlight housing and the radiator support frame on each side. 3. Pull back the grille and remove the Phillips screw that attaches the fascia to the hood latch support (Fig.D). 4. On each side, remove three plastic fasteners: two of the plastic fasteners are attaching the fender liner to the fascia (Fig.E); the other plastic fastener is attaching the fender liner to the frame rail (Fig.F) 5. Remove ten 10mm (head) bolts (Fig.G) and two plastic fasteners (Fig.H) attaching the lower splash shield to the fascia and the sub frame. 6. On both sides, pull back the fender liner and remove one 10mm screw attaching the corner of the fascia to the fender (Fig.I). Fig.K Plastic fastener MOUNTING BRACKET KIT INSTALLATION INSTRUCTIONS ROADMASTER, Inc. 6110 NE 127th Ave. Vancouver, WA 98682 1-800-669-9690 fax 360-735-9300 KIT# 1180-1 05/14/10 KS 9. Remove the foam shock absorption core by pulling forward (Fig. L). Note: this will not be reinstalled. Retain the foam shock absorption core and attachment hardware so that it can be replaced if the bracket is ever removed. 10. Remove six 14mm (head) bolts to remove the bumper core (Fig.M). Note: this will not be reinstalled. Retain the bumper core and attachment hardware so that it can be replaced if the bracket is ever removed. 11. Remove the alignment studs at the end of each frame rail (Fig.N). 12. Now, place the main receiver brace into the ends of the frame rails (Fig.O). 13. Bolt the main receiver brace into place using the three supplied 10mm x 1.25 x 35mm bolts, flat washers and lock washers (Fig.P). Repeat for the other side. Tighten to the torque specifications listed at the end of these instructions.

1996 – 2000 Civic 2-door Front Windows Bind or Have Come Out of the Run Channel Repair Manual

download
REPAIR PROCEDURE 1. Remove the door panel. Refer to section 20 of the 1996-00 Civic Service Manual. 2. Remove the armrest bracket, then pull down the plastic cover to gain access to the window regulator. 3. Carefully move the glass until you can see the glass mounting bolts, then loosen them. Slide the guide rearward, remove the glass from the guide, and carefully pull the glass out through the window slot. 4. Check the year and VIN. If the vehicle is a 1996 or 1997 within the affected VIN range, replace the window regulator. Go to step 5. If the vehicle is not a 1996 or 1997 within the affected VIN range, go to step 8. 5. Remove the two roller guide bolts and the two rear regulator mounting bolts; then remove the front regulator mounting bolts. 6. Disconnect the power window motor connector, and detach the harness clip (if applicable); then lift and remove the regulator through the opening in the door. 7. Install the new regulator in the door, then loosely install the two rear mounting bolts and the two roller guide bolts. Do not tighten the two front mounting bolts yet. Go to step 9. 8. Loosen the window regulator’s two rear mounting bolts, two front mounting bolts, and two roller guide bolts