Skip to content

wires for drivers side back door on 2008 dodge caravan

You search PDF repair manual about wires for drivers side back door on 2008 dodge caravan, if there are search results will appear below. If search results do not exist, please search by others keyword.

2008 HONDA ACCORD 4-DOOR BACK-UP SENSOR INSTALLATION INSTRUCTIONS

download
INSTALLATION NOTE: When installing a back-up sensor and a trailer hitch, install the back-up sensor before installing the trailer hitch. 1. Make sure you have the anti-theft code for the radio and navigation system (if equipped), then write down the radio presets. 2. Disconnect the negative cable from the battery 3. Remove the two caps from the rear bumper, and remove the rear bumper (two bolts, six self-tapping screws, and two clips). NOTE: Have an assistant help you when removing and installing the rear bumper. 4. Remove the trunk floor mat (one clip). 6D26050E CLIPS 2 CAPS REAR BUMPER 6 SELF-TAPPING SCREWS 7109070E CLIP TRUNK FLOOR MAT 5. Remove the rear trunk trim panel (four clips and three hooks). Remove the trunk left side trim panel (five clips). 8. Remove the left rear speaker cover (nine retaining tabs). 710908AE LEFT TRUNK SIDE TRIM PANEL 3 CLIPS 2 CLIPS 7115030E LEFT REAR SPEAKER COVER 9 RETAINING TABS 9. Remove the left rear speaker (one bolt and disconnect the vehicle connector). 10. Attach the control unit bracket to the control unit 11. By hand, thread the 6 mm flange nut onto the control unit bracket stud. Insert the control unit bracket into the hole in the vehicle panel as shown. Secure the bracket to the vehicle panel. VEHICLE PANEL CONTROL UNIT CONTROL UNIT BRACKET HOLE 6 mm FLANGE NUT HOLE CONTROL UNIT BRACKET

1998 Dodge Grand Caravan Fuel Pump Relay Removal And Installation Manual

download
Fuel Pump Relay 1. Remove fuel pump relay from power distribution center at driver’s side front corner of engine compartment, near the battery. Note terminal identification on fuel pump relay. See Fig. 6 . 2. To check fuel pump relay resistance, use ohmmeter and check resistance between terminals No. 85 and 86 on fuel pump relay. Replace fuel pump relay if resistance is not 70-80 ohms. 3. To check fuel pump relay operation, connect ohmmeter between terminals No. 30 and 87A on fuel pump relay. See Fig. 6 . Ohmmeter should indicate continuity between terminals No. 30 and 87A on fuel pump relay. 4. Connect ohmmeter between terminals No. 30 and 87 on fuel pump relay. See Fig. 6 . Ohmmeter should indicate no continuity between terminals No. 30 and 87 on fuel pump relay. 5. Connect 16-gauge jumper wire between negative battery terminal and terminal No. 85 on fuel pump relay. Connect 16-gauge jumper wire between positive battery terminal and terminal No. 86 on fuel pump relay. 6. Fuel pump relay should now be energized. No continuity should now exist between terminals No. 30 and 87A on fuel pump relay. Continuity should now exist between terminals No. 30 and 87 on fuel pump relay. Disconnect jumper wires. Replace fuel pump relay if defective. 7. If fuel pump relay or wiring circuit failure exists, a Diagnostic Trouble Code (DTC) will be stored in Powertrain Control Module (PCM). See appropriate G – TESTS W/CODES article. Fig. 6: Identifying ASD Relay & Fuel Pump Relay Terminals Courtesy of CHRYSLER CORP.

2007-2008 Toyota Tundra Crew Cab Installation Manual

download
1. Cover the front seats, floorboards, dash and steering wheel with a clean drop cloth or disposable plastic covers. Note: Always wear eye and hand protection when working with glass. Make sure that you have the right glass and the urethane systems are current. Windshield part numbers are FW02724, FW02723, FW02722 or FW02721. 2. Remove the rearview mirror by loosening the Tork screw using a T-20 Tork screwdriver. Slide the wire-harness trim cover off the headliner. Slide the mirror off the mirror bracket in an upward motion. 3. Disconnect the wire harness from the underside of the hardware with a small flat-tip screwdriver or your fingernails. 4. Remove the windshield-wiper nuts using a wrench or socket. If the nuts are tight, loosen them with a 14-millimeter wrench and then come back with your socket. Move the wiper arm in an up-and-down motion to break it loose from the post, or use a wiper puller. Caution: Wipers can sometimes be hard to remove. To avoid stressing the post, use a wiper puller. The wipers are marked; take note to ensure proper re-installation. 5. Using a No. 2 Phillips-tip screwdriver, remove the two plastic screw inserts on the fasteners located on the outer edge of the cowling corners. There is one on the passenger’s side and one on the driver’s side. A5a A5b 2007-08 Toyota Tundra Crew Cab By Gilbert R. Gutierrez Vehicle type: Four-door, crew-cab pickup truck NAGS numbers*: Windshield part numbers are FW02724, FW02723, FW02722 or FW02721; front door glass FD23323- 24 R-L; rear door glass FD23325-26 R-L; and back glass FY95054, FY95053, FB23336, FB23335 and FB23334. Helpful tools or supplies: Retention tape or a rubber hose to protect the fenders and hood; a PryBaby for molding and panel removal. Watch for: Be careful not to pull too hard on the rearview mirror harness during removal to avoid ripping the headliner. When removing or re-installing the A-pillar trim panels, take care to avoid disturbing the curtain air-bag harness. *With permission from National Auto Glass Specifications. Call NAGS at 800/551-4012 or visit www.nags.com. Vehicle information A1 A2 A3a A3b A4a A4b 35 6. Remove the rubber corner pieces from the corners of the cowling at the base of the windshield. Using an outward motion, pull out the rubber piece, and then gently pull the rubber insert from the cowling. 7. With the hood open, push in and pop loose the six plastic tab fasteners using a No. 1 PryBaby tool from the underside. There are three on the passenger’s side and three on the driver’s side, with a guide pin at the center. 8. Remove the two-part cowl by sliding it in an upward-outward motion toward the engine compartment, disengaging the eight underside tabs on the front part of the cowling from the base of the windshield. Tape the hood and fender with molding-retention tape to avoid gnarling or scratching the cowling. Note: When re-installing the cowling, use a No. 1 PryBaby tool to assist in the installation of the cowling onto the bottom of the windshield. 9. If using a cold knife or power tool to cut out the glass, remove the A-pillar trim panels, as the windshield fits close to the pinchweld. 10. Remove the door weatherstrip. 11. Remove the screw covers using a No. 2 PryBaby. 12. Remove the two 10-millimeter bolts hidden beneath the covers using a 10-millimeter socket-wrench driver. Pull the handle loose. 13. Remove the A-pillar trim panels using a door-panel remover or No. 2 PryBaby tool. Caution: Be careful not to dis- A6a A6b A6c A7a A11a A11b A12a A12b A7b A7c A8 A10 A13a A13b 36 AutoGlass™ •March/April 2008 Installation ? F or T echnicians Only turb the curtain air-bag harness when removing or re-installing the A-pillar trim panels. Note: Before beginning windshield removal, verify the new windshield is the correct one and the urethanes and primers are current. Never use outdated products as this could jeopardize the structural integrity of the vehicle and the safety of its passengers. Removal 14. Make sure cutting blades are sufficiently sharp. 15. Before cutting out the windshield, remove contaminants from the glass and pinchweld to prevent contact with the urethane. 16. If using a cold knife, use a 3? 4 -inch blade. Cut three sides; then use a long knife or power tool to cut the bottom of the windshield. Note: There are no gravity stops on this windshield. 17. If trying to save the windshield, use an Equalizer with an 8-inch blade. Note: When using any power tool, lubricate the cutting area with water. Spray the top and sides; then make your cuts. 18. After cutting the sides and top, cut out the bottom portion of the glass using an Equalizer Express. Spray the bottom of the windshield with water at least 4-to-5 inches above the urethane on the glass, so the water flows down into the urethane while you make your final cut across the bottom of the windshield. Caution: Never use your head to push, as this could result in back and neck injuries. 19. Take the windshield out of the opening using a set of vacuum cups. Lift the glass and place it on a windshield stand or suitable workstation. Installation 20. After cutting the windshield out, remove contaminants such as dirt, moisture and other debris from the pinchweld. Clean the dashboard. 21. Dry fit the new glass to the opening. Mark your glass using a grease pencil or molding-retention tape. 22. Place your vacuum cups on the windshield in the appropriate location for a one-person set. 23. For driver-side setting of the windshield using a Glass Handler Kit, place the kit’s elbow-setting pad on the driver’s side of the hood area; then lift the windshield from the stand using the vacuum cups. 24. Reach over, place your elbow on the setting pad and set the windshield onto the old urethane. 25. With the windshield resting in the opening, make sure it is in the right spot. 26. Adjust both sides to the correct setting, marking the passenger’s side, then the driver’s side. Lift the glass and place it on a windshield stand or suitable workstation. 27. Follow the urethane manufacturer’s recommendations for installation. 28. Clean the inside of the windshield using a urethane manufacturer-recommended product; follow recommended steps. Note: Do not touch the bonding area of the windshield after cleaning, prepping or priming it. 29. Wear powder-free Nitrile gloves to keep off chemicals. 30. Apply the glass prep and primer, following the urethane manufacturer’s recommendations.

2008 TOYOTA RAV4 DOOR SILL ENHANCEMENT REPAIR MANUAL

download
1. Check Kit Content. (a) Check kit for content and damage. (Fig. 1-1) 2. Apply tape. (a) Using the factory door sill plate as a guide, apply tape to the door sill surface at each end of the sill plate as shown. (Fig. 2-1) 3. Remove Factory Door Sill Plates. (a) Using an NRT, Lift the edge of the factory sill plate. (Fig. 3-1) (b) Once the edge of the sill plate has been lifted the plate may be removed by hand by pulling firmly upward. Be sure not to damage the weather strip in the process. (c) Discard the factory door sill plate. Fig. 2-1 Fig. TOYOTA RAV4 2008 – DOOR SILL ENHANCEMENT Procedure Page 3 of 5 pages Issue: A 12/3/07 4. Installation Preparation. (a) Thoroughly clean all installation surfaces. (i) Use a clean lint free cloth. (ii) Clean surface thoroughly using VDC approved cleaner and wipe dry Do allow cleaner to air dry. (Fig. 4-1) (b) Ensure door sill enhancement to be between 70 F and 110 F at time of installation. (c) Ensure vehicle surfaces to be between 70 F and 110 F at time of installation. (d) Do not touch or allow debris or contaminates to come in contact with the adhesive backing before installation. (e) Inspect parts prior to installation. Dry fit parts for alignment reference. 5. Install Front Door Sill Enhancements. (a) Check Part Number label on back of door sill enhancement for applicable side of vehicle, Right Hand or Left Hand and Front or Rear. (b) Position part over vehicle door sill area to check for proper fit and orientation prior to installation. NOTE: The vehicle name logo on the door sill enhancement must be oriented as to be read from the outside of the vehicle. (c) Remove the tape liner from the door sill enhancement. Do not touch the adhesive

1997 Dodge Grand Caravan POWERTRAIN CONTROL MODULE REMOVAL AND INSTALLATION MANUAL

download
POWERTRAIN CONTROL MODULE (PCM) Removal & Installation 1. The PCM is located between driver’s side front fender and power distribution center, near battery. See Fig. 1 . Disconnect negative battery cable and then positive battery cable from battery. 2. Remove bolts on side of power distribution center that secure power distribution center to mounting bracket. Remove heat shield from outside of battery. Remove battery. 3. Rotate power distribution center toward the engine to disengage power distribution center from rear mounting bracket. Pull power distribution center toward rear of vehicle to disengage power distribution center from front mounting bracket. 4. Allow power distribution center to lay aside for access to PCM. Remove electrical connectors from PCM. Electrical connectors may be removed by squeezing tabs on electrical connector together and pulling electrical connector from PCM. Remove bolts and PCM. To install, reverse removal procedure. Vehicles equipped with engine or transmission computers may require a relearn procedure after the vehicle battery is disconnected. Vehicle computers memorize and store vehicle operation patterns for optimum driveability and performance. When the vehicle battery is disconnected, this memory is lost. Default data is used until new data from each key start is stored. As the computer restores its memory from each new key start, driveability is restored. Driveability problems may occur during the relearn stage. Depending on the vehicle and how it is equipped, the following driveability problems may exist: z Rough or unstable idle. z Hesitation or stumble. z Rich or lean running. z Poor fuel mileage. z Harsh or poor transmission shift quality. To accelerate relearn process after battery removal and installation, vehicle should be road tested in the following manner: z Vehicle at normal operating temperature (cooling fan cycles). z Accelerate at normal throttle position (20-50%). z Cruise at light to medium throttle. z Decelerate to a stop, downshifting and using brakes normally. Manufacturers identify specific relearn procedures. See RELEARN PROCEDURES. Always complete the procedure before returning the vehicle to the owner. RELEARN PROCEDURES Theft Alarm Relearn Procedure 1. Theft alarm relearn is necessary whenever battery is disconnected or dead battery is boosted. If battery is connected or boosted without conducting relearn procedure, alarm system will enter power-up mode and vehicle will not start. 2. Before reconnecting battery or connecting booster, insert door key into driver side door lock