Skip to content

workshop manual section 412 02 ford taurus

You search PDF repair manual about workshop manual section 412 02 ford taurus, if there are search results will appear below. If search results do not exist, please search by others keyword.

2004-2007 Ford F-Super Duty SLIDING POWER WINDOW (BACK GLASS) SERVICE MANUAL

download
FORD: 2004-2007 F-Super Duty ISSUE SERVICE PROCEDURE Some 2004-2007 F-Super Duty vehicles, equipped with a power sliding rear window (back glass), may 1. Prior to window removal, verify that center exhibit a stuck or binding concern. This condition glass is centered in the upper plastic channel may be due to the center glass not being positioned (Figure 1). If center glass is not inside upper correctly inside the upper or lower channel, the plastic channel, pull channel down and out of channel being warped, bent, or center glass upper aluminum channel and slide back in de-bonded. making sure the entire center glass is inside the plastic channel. ACTION Follow the Service Procedure steps to correct the condition. Figure 1 – Article 06-15-5 2. If Step 1 resolves the issue, return the vehicle 4. Refer to window removal procedure. (Refer to back to customer after verifying the window Workshop Manual (WSM), Section 501-11-24 functions properly. If it did not resolve the and 501-11-25.) issue, proceed to Step 3. 5. Remove cable clips from sheet metal. (Refer to 3. Open the rear window approximately half way. WSM, Section 501-11-28.) 6. Remove three (3) motor bracket attaching bolts. (Refer to WSM, Section 501-11-28. 7. Disconnect motor wiring harness from vehicle 9. Pull outer rubber seal from window frame body harness. (Refer to WSM, Section (Figure 2). 501-11-29.) 8. Remove window assembly from vehicle window opening. Figure 2 – Article 06-15-5 10. Locate two (2) screws in bottom of lower frame and remove them with a R1 square bit screw driver (Figure 3). Figure 3 – Article 06-15-5

2003 Ford F-Super Duty 250-550/ Excursion Rear Drive Axle/Differential/ Ford 10.50-Inch Ring Gear Installation Manual

download
1. Remove the differential case. For additional information, refer to Differential Case in this section. 2. NOTE: The differential bearings need not be removed to overhaul the Ford limited slip differential. If bearing removal is required, for additional information, refer to Differential Case in this section. NOTE: The anti-lock speed sensor ring cannot be reused once removed. Remove the differential pinion shaft lock bolt and remove the differential pinion shaft. ? If required, remove the ring gear and anti-lock speed sensor ring. 3. NOTE: This tool does not have the 1/2-inch drive hole. Install the special tool in a suitable vise. 2003 F-Super Duty 250-550/Excursion Workshop Manual 5. Install the special tool in the bottom side gear bore. ? Apply a small amount of grease to the centering hole of the special tool. 6. Install the nut in the upper differential side gear. Hold the nut in position while installing the hex screw. Tighten the hex-head screw until contact is made with the Step Plat 2003 F-Super Duty 250-550/Excursion Workshop Manual 7. Insert a suitable dowel bar in the hole of the nut. Tighten the forcing screw to force the differential side gear away from the differential pinion gears. The dowel bar is used to keep the nut from turning when the forcing screw is tightened. NOTE: Differential pinion thrust washers cannot be removed independently of the differential pinion gears and so must be removed simultaneously with the differential pinion gears. Insert the special tool in the pinion shaft bore and turn the differential case to “walk” the differential pinion gears and differential pinion thrust washers out to the differential case windows. 9. Remove the differential pinion gears and differential pinion thrust washers. 10. Remove the differential side gears and differential clutch packs and tag them RIGHT and LEFT with the shim

2002 Ford Taurus WATER IN THE BLOWER CASE BLOWER MOTOR AND/ OR RESISTOR FAILURE REPAIR MANUAL

download
SERVICE PROCEDURE 1. Access blower motor and resistor per the Workshop Manual Sections 412-02 and 412-04. Inspect for evidence of water/corrosion. If water/corrosion are found or parts have failed, replace per Workshop Manual (blower motor 1F1Z- 19805-AA and resistor F6DZ-19A706-AA). 2. Visually inspect the Cowl Vent Screen located under the RH windshield wiper to verify if the screen is fully seated. Inspect the rubber seal on the vent screen which should be fully seated against the windshield. If the cowl vent screen is not fully seated and appears warped, it must be replaced (4F1Z-54018A16- BAA). 3. Remove the cowl vent screen per the Workshop Manual Section 412-01 Pollen Filter Removal and inspect the cabin filter to confirm it is fully seated. Re-seat the filter as necessary. Inspect rain-hat base to make sure it is secure and sealed to the body. Reposition and reseal as necessary using Clear Silicone Rubber TA-32. 4. Remove the foam sealant expulsion at lower front outboard corner base of the rain-hat (Figure 1). Zoom Sized for Print 5. Locate the tape as shown (Figure 2). Remove the tape and apply Clear Silicone Rubber TA-32 to the small hole as shown (Figure 2) Parts Block Zoom Sized for Print 6. Install the Rain-Hat Extension Seal or Shed Lip Seal 4F1Z-54022A54-AA to the outboard edge of the rain-hat (see Figure 2 for installation). The 10 mm by 10 mm (0.5″ by 0.5″) cut area, located 25 mm (1″) from the end of the seal, will face down and locate at the 90 degree bend of the rain-hat on the fender side (Figure 3). 7. Prior to installation of the cowl vent screen, verify that the cabin filter cover is properly snapped in place and the clip is located on the inboard side, (toward the center of the bulkhead), the cover will feel loose if not properly snapped in place. Reinstall the cowl vent screen per Section 412-01 of the Workshop Manual.

2003-2005 FORD Excursion 6.0L TURBOCHARGER CARBON DEPOSIT DIAGNOSTICS AND SERVICE MANUAL

download
For F-Super Duty, Excursions, and E-Series Once each of the tests are complete, use the IDS vehicles built on or after 9/30/2003, install the VPS help icon on the right side of the screen in each tool 418-626 along with IDS/VMM. The 418-626 test to help analyze the results. If the turbo fails was shipped in kit TKIT-2007VP-F and and leads to turbocharger replacement, continue TKIT-2007TV-F. Dealers should have received one with the Turbocharging Inspection Procedure to or the other of these two kits. check for internal turbocharger oil leakage and to determine if the turbocharger can be repaired with a To Install VPS CHRA replacement, or if it can be cleaned, instead of replacing the entire turbocharger. 1. Remove the threaded pipe plug from center housing of turbo. If the turbocharger passes the turbo tests, do not continue with this TSB. Follow the online KA pin 2. Remove the oil supply flange bolt closest to the point test found on the Professional Technician turbo label. Society (PTS) website and continue air 3. Drop in the VPS and secure with provided management diagnosis without replacing the clamp flat side up. turbocharger. 4. Torque the oil supply line bolt 7 lb-ft (10 N•m). NOTE VEHICLE PERFORMANCE ISSUES RELATED TO 5. The gasket is reusable and need only be FUEL QUALITY, MAINTENANCE AND replaced if an oil leak is present after final AFTERMARKET MODIFICATIONS ARE NOT assembly. COVERED BY FORD MOTOR COMPANY WARRANTY. To run test, start new session in IDS with VPS/VMM connected to the vehicle. Then select the Turbocharger Inspection Procedure Toolbox-Powertrain-Air Management-Boost test and follow the IDS screen prompts, and then continue 1. Remove the turbocharger for inspection with VVT test. Both the boost and VVT test should following Workshop Manual, Section 303-04D: be run in order. Fuel Charging and Controls. 2. Inspect compressor and turbine wheel fins for damage. Replace the turbocharger if fins are damaged. If fins are damaged, inspect the air intake system for damage allowing dirt or contamination to bypass the air filter

2002 Ford Lincoln LS Valve Cover LH Workshop Manual

download
Valve Cover LH Removal 1. Disconnect the battery ground cable. For additional information, refer to Section 414-01 . 2. Remove the air cleaner outlet tube. For additional information, refer to Section 303-12 . 3. Remove the air cleaner housing. 1. Disconnect the mass air flow (MAF) sensor electrical connector. 2. Remove the bolt. 3. Remove the housing. 4. CAUTION: To disconnect the Norma fitting, squeeze the tabs and pull straight out or damage to the fitting can occur. Disconnect the crankcase ventilation tube. 5. Disconnect the fuel hose. For additional information, refer to Section 310-00 . 6. Disconnect the evaporative emission canister purge valve hose. 7. Remove the vapor management valve (VMV) cover. SECTION 303-01B: Engine — 3.9L 2002 Lincoln LS Workshop Manual IN-VEHICLE REPAIR Procedure revision date: 05/17/2001 Material Item Specification 8. Remove the VMV. 1. Disconnect the vacuum hose. 2. Disconnect the purge hose. 3. Disconnect the electrical connector and the push pin. 4. Remove the nuts and the valve. 9. Remove the exhaust gas recirculation (EGR) vacuum regulator solenoid. 1. Disconnect the electrical connector. 2. Remove the screws and the EGR vacuum regulator solenoid. 10. Remove the bracket. 1. Remove the hose. 2. Remove the bracket. 11. Position the engine wiring harness up. 12. Remove the ignition coil cover. * Inspect the gasket and install a new gasket as necessary.