Skip to content

yhs 001

You search PDF repair manual about yhs 001, if there are search results will appear below. If search results do not exist, please search by others keyword.

TIMING BELT COMPONENTS FOR REMOVAL AND INSTALLATION MANUAL

download
TIMING BELT REMOVAL 1. DRAIN ENGINE COOLANT 2. REMOVE ENGINE UNDER COVER 3. REMOVE AIR CLEANER DUCT 4. REMOVE DRIVE BELT, FAN WITH FLUID COUPLING AND WATER PUMP PULLEY (See step 5 in water pump removal in Cooling System) 5. REMOVE RADIATOR ASSEMBLY (See steps 5 and 6 in radiator removal in Cooling System) 6. REMOVE NO.3 TIMING BELT COVER (a) Remove the oil filler cap. (b) Using a 5 mm hexagon wrench, remove the 6 bolts and belt cover. 7. REMOVE NO.2 TIMING BELT COVER Using a 5 mm hexagon wrench, remove the 3 bolts, belt cover and gasket. If you are unable to loosen the bolt on the right because the PS pump pulley interferes with the hexagon wrench, first remove the pulley as follows. (a) Using SST to hold the pulley, remove the nut. SST 09960-10010 (b) Remove the pulley. 8. REMOVE DRIVE BELT TENSIONER Remove the 3 bolts and tensioner. – ENGINE ENGINE MECHANICAL EG-19 9. SET NO.1 CYLINDER TO TDC/COMPRESSION (a) Turn the crankshaft pulley, and align its groove with timing mark “0″ of the No.1 timing belt cover. NOTICE: Always turn the crankshaft clockwise. (b) Check that the timing marks of the camshaft timing pulleys are aligned with the timing marks of the No.4 timing belt cover. If not, turn the crankshaft 1 revolution (360?). 10. REMOVE TIMING BELT FROM CAMSHAFT TIMING PULLEYS HINT (Re-using timing belt): Place matchmarks on the timing belt and camshaft timing pulleys as shown in the illustration. (a) Alternately loosen the 2 bolts, and remove them, the tensioner and dust boot. (b) Disconnect the timing belt from the camshaft timing pulleys. 11. REMOVE CAMSHAFT TIMING PULLEYS Using SST, remove the bolt for the timing pulley. Remove both timing pulleys. SST 09960-10010 (09962-01000, 09963-01000) 12. REMOVE CRANKSHAFT PULLEY (a) Using SST, loosen the pulley bolt. SST 09213-70010, 09330-00021 (b) Remove the SST and pulley bolt

2001 Subaru Legacy GT Sedan AWD F4-2.5L SOHC Steering and Suspension, Wheel Bearing, Service and Repair Manual

download
1. Remove knuckle. Refer to Steering and Suspension. 2. Using ST1 and ST2, remove hub from rear housing. 3. Remove back plate from rear housing. 4. Using a standard screwdriver, remove outer and inner oil seals. CAUTION: Use new oil seals. 5. Using flat bladed screwdriver, remove snap ring. 6. Using ST1 and ST2, remove bearing by pressing inner race. ST1 927430000 HOUSING STAND ST2 927440000 BEARING REMOVER CAUTION: * Do not remove bearing unless damaged. * Do not re-use bearing after removal. 7. Remove tone wheel bolts and remove tone wheel from hub (only vehicle equipped with ABS). 8. Using ST, press hub bolt out. ST 927080000 HUB STAND. CAUTION: Be careful not to hammer hub bolts. This may deform hub. INSPECTION Check the removed parts for wear and damage. If defective, replace with a new one. CAUTION: * If a bearing is faulty, replace it as the bearing set. * Be sure to replace oil seal at every overhaul. ASSEMBLE 1. Using ST, press new hub bolt into place. CAUTION: * Ensure hub bolt closely contacts hub. * Use a 12 mm (0.47 inch) hole in the ST to prevent hub bolt from tilting during installation.

4T65E Transmission 1-2 Shift Shudder at Light to Moderate Acceleration (Replace Complete Second Clutch Assembly)

download
2001-2004 Buick Regal 2001-2005 Buick Century, LeSabre 2002-2007 Buick Rendezvous 2005-2007 Buick Terraza, LaCrosse, Allure (Canada Only) 2006-2007 Buick Lucerne 2001-2005 Chevrolet Venture 2001-2007 Chevrolet Impala, Monte Carlo 2005-2007 Chevrolet Uplander 2006-2007 Chevrolet Malibu SS, Malibu Maxx SS 2001-2002 Oldsmobile Intrigue 2001-2003 Oldsmobile Aurora 2001-2004 Oldsmobile Silhouette 2001-2005 Pontiac Aztek, Bonneville, Montana 2001-2007 Pontiac Grand Prix 2005-2007 Pontiac Montana SV6 2006-2007 Pontiac G6 GTP 2005-2007 Saturn Relay with 4T65E Automatic Transmission this service kit contains: Second Clutch Housing Fluid Seal Rings (613), a Second Clutch Assembly (617), a Case Cover (Channel Plate) Upper Gasket (430), and a Case Cover (Channel Plate) Lower Gasket (429). In addition to the content of this service kit, four other gaskets not included in this service kit will also be needed to complete the repair, a Control Valve Body Cover (Side Cover) Gasket (54), a Control Valve Body Cover (Side Cover) Inner Gasket (59), a Case Cover Lower Gasket (429), and a Case Cover Upper Gasket (430). These gaskets can be obtained by ordering service kit P/Ns 24206959 and 24206391. Be sure to use ONLY the Second Clutch Assembly and Second Clutch Housing Fluid Seal Rings provided in this service kit. DISCARD the Second Clutch Assembly and Second Clutch Housing Fluid Seal Rings removed from the transmission being serviced. Disassemble ONLY the Oil Pump Assembly from the Case Cover (Complete). DO NOT disassemble the Control Valve Body from the Case Cover. Remove ONLY the Case Cover-to- Case bolts to remove the Case Cover and Valve Body from Transmission Case AS AN ASSEMBLY . To access all Case Cover-to-Case bolts, it is necessary to remove the Pressure Control Solenoid Valve Assembly (322), and 1-2 & 3-4 Shift Solenoid Valve Assemblies (315A, 315B).

2009 Toyota Corolla AXLE AND DIFFERENTIAL: FRONT AXLE HUB: INSTALLATION MANUAL

download
INSTALLATION 1. INSTALL FRONT AXLE HUB BEARING 2. INSTALL FRONT DISC BRAKE DUST COVER (a) Install the disc brake dust cover to the steering knuckle with the 3 bolts. Torque: 8.3 N·m (85 kgf·cm, 73 in·lbf) 3. INSTALL FRONT AXLE HUB SUB-ASSEMBLY 4. INSTALL FRONT AXLE HUB HOLE SNAP RING Last Modified: 4-24-2008 5.1 A From: 200712 Model Year: 2009 Model: Corolla Doc ID: RM000001IWX00ZX Title: AXLE AND DIFFERENTIAL: FRONT AXLE HUB: INSTALLATION (2009 Corolla) (a) Using SST and a press, install a new front axle hub bearing to the steering knuckle. SST: 09950-60020 09951-00720 SST: 09950-70010 09951-07100 (a) Using SST and a press, install the front axle hub sub-assembly. SST: 09608-32010 SST: 09950-60010 09951-00600 SST: 09950-70010 09951-07100 5. INSTALL FRONT LOWER BALL JOINT 6. INSTALL FRONT AXLE ASSEMBLY 7. INSTALL FRONT LOWER SUSPENSION ARM 8. INSTALL TIE ROD END SUB-ASSEMBLY 9. INSTALL FRONT DISC 10. INSTALL FRONT DISC BRAKE CALIPER ASSEMBLY 11. TEMPORARILY INSTALL FRONT AXLE HUB NUT (a) Using snap ring pliers, install a new front axle hub hole snap ring. (a) Align the matchmarks and install the front drive shaft assembly to the front axle hub sub-assembly. (b) Install the front axle assembly to the front shock absorber with the 2 bolts and the 2 nuts. Torque: 240 N·m (2448 kgf·cm, 176 ft·lbf) Be careful not to damage the drive shaft boot or speed sensor rotor. Page 2of 4

1999 Buick Regal DTC B1001 Option Configuration Error Repair Manual

download
Test Description The number(s) below refer to the step number(s) on the diagnostic table. 2. This step checks to see if the correct VIN is programmed in the powertrain control module (PCM). 4. This step checks to see if the body control module (BCM) has been replaced. 5. This step explains the proper steps to perform after a BCM has been replaced in order for the <- Back Forward -> Document ID# 385021 1999 Buick Regal Print BCM to operate properly. 6. This step checks to see if the correct VIN is programmed in the BCM. 7. This step explains how to properly program the VIN into the BCM. DTC B1001 Option Configuration Error Step Action Value (s) Yes No 1 Was the SIR Diagnostic System Check performed? — Go to Step 2 Go to SIR Diagnostic System Check 2 1. Install the scan tool. 2. Use the scan tool to verify that the PCM is programmed with the correct VIN by comparing the VIN that is stored in the PCM to the VIN plate of the vehicle. Is the PCM programmed with the correct VIN? — Go to Step 4 Go to Step 3 3 Use the scan tool and/or the techline machine to program the correct VIN into the PCM. Is the programming procedure complete? — Go to Step 9 — 4 Was the BCM replaced? — Go to Step 5 Go to Step 6 5 1. Use the F2 function key and follow the instructions on the scan tool under the BCM SPECIAL FUNCTIONS to reprogram the BCM. This allows the BCM to learn the Restraints ID from the SDM and also to learn other important data that is required. 2. Use the F6 function key and follow the instructions on the scan tool under the BCM SPECIAL FUNCTIONS to program the correct VIN into the BCM. 3. Use the techline machine to perform the theft relearn procedures for the replacement BCM. Are the programming procedures complete? — Go to Step 9 — 6 Use the scan tool to verify that the BCM is programmed with the correct VIN by comparing the VIN that is stored in the BCM to the VIN that is stored in the PCM. Is the BCM programmed with the correct VIN? — Go to Step 8 Go to Step 7 7 Use the F6 function key and follow the instructions on the scan tool under the BCM SPECIAL FUNCTIONS to program the correct VIN into the BCM. Is the reprogramming procedure complete? — Go to Step 9 — 1. Turn the ignition switch to the OFF position. 2. Replace the SDM. Refer to Inflatable Restraint