Skip to content

youtube toyota sienna

You search PDF repair manual about youtube toyota sienna, if there are search results will appear below. If search results do not exist, please search by others keyword.

2004 – 2006 Toyota Sienna Vehicles Equipped w/ Power Back Door (Power Rear Liftgate) Repair Manual

download
Certain 2004 – 2006 Model Year Sienna vehicles equipped w/Power Back Door (Rear Liftgate) Q1: What is the condition? A1: Toyota has determined that the gas struts used to help lift and support the Power Rear Liftgate in certain 2004 through 2006 model year Sienna vehicles could be wearing out sooner than expected. As the gas struts deteriorate, the performance of the Power Rear Liftgate will begin to degrade, and the Power Rear Liftgate will operate more slowly than when the gas struts were new. Only Sienna vehicles equipped with the Power Rear Liftgate are involved. Q2: Are there any warnings that this condition exists? A2: Owners may notice that the Power Rear Liftgate will not remain in the open position. If not repaired, the gas struts may not be able to support the weight of the liftgate when it is open, and eventually, the gas struts could deteriorate to the point that the liftgate will fall about ten inches after it reaches the fully open position, at which point the power motor will engage and power the liftgate to the fully closed position. This condition may cause injury to a person who is struck by the liftgate when it falls or when it is closing. Q3: When were these vehicles produced, and how many vehicles are involved? A3: Only certain 2004 through 2006 model year Sienna vehicles equipped with the Power Rear Liftgate, produced between January 2003 and December, 2006 are involved. Approximately 196,000 vehicles are involved nationwide.

TOYOTA SIENNA SEAT REMOVAL AND INSTALLATION MANUAL

download
Front Seat Installation Instructions 1. Roll seat base into position, just behind the floor mounted strikers. Pull up the release handle. 2. Lift the rear of the seat base up (a) and slide it forward (b) to engage the front strikers. 3. Push down on rear of seat to engage rear strikers. Push down the release handle to lock the seat base into place. 4. Connect (plug) seat electrical harness to B-pillar receptacles. See pages 36 and 37 for details. Position seat and pull release handle up. 1 2 3 Lift up (a) and slide forward (b) to engage front strikers. Push down to engage rear strikers. Push down handle to lock into place

1998 – 2003 Toyota Sienna SLIDING DOOR DIAGNOSTIC TIPS/ REPAIR MANUAL

download
CONDITION POSSIBLE CAUSE COMMON REPAIR Top RollerComes Rail bent or widened condition Replace the upper slide door rail. Top Roller Comes Out of Rail Guide The stopper at the end of the rail is loose or missing. Replace the stopper as needed. Door Does Not Lock in Full Open Position Full open stop latch assembly is damaged. Replace the full open stop latch assembly. Left Door Opens Half Way Fuel door half stopper cable damaged. Adjust the cable. Replace the cable, if damaged. Difficltto Open Dirty weatherstrip. Clean all soda spills or other sticky substances that may have accumulated on weatherstrip and door. Difficult to Open Manually Inside handle release button damaged. Replace inside handle release button assembly according to TSB No. BO027-00, “Sliding Door Handle Push Button Operation”. Door out of adjustment. Adjust levelness of the door, according to Repair Manual. Dragging Open/Close Mll Running board rubs against the bottom of the sliding door. Adjust running board to proper position and assure clearance from the door. Manually Roller rails have bent or warp condition. Dirt or debris in the rails and rollers. Clean rails and rollers. Replace damaged parts. CONDITION POSSIBLE CAUSE COMMON REPAIR Creak Noise Junction block, damaged components, and other issues Refer to TSB No. BO003-99, “Sliding Door Creak Noise Reduction.” Refer to the “Common Sources of Creak Noise” section of this bulletin for additional information for sources of creak noise. Rattle or Clicking (NOT Creak Noise) Door moving when driving over bumps Rollers loose or damaged Adjust lower roller base mounting to bring door closer to body (Refer to TIS, applicable model year Sienna Repair Manual, Vehicle Exterior – Door/Hatch – “Slide Door: Adjustment”). Adjust strikers to bring door closer to the body. Inspect the latch assembly and replace, if damaged. Replace damaged rollers. Noise During Open/Close Rollers or rails are damaged and/or dirty. Inspect, clean, and/or replace as needed

2004 Toyota Sienna POWER SLIDING DOOR INOPERATIVE Repair Manual

download
Remove Slide Door Window Garnish. A. Fully open the slide door window. B. Remove the glass run. C. Using a screwdriver, disengage the clip and remove the garnish. HINT: Tape the screwdriver tip before use. D. Using the taped screwdriver, disengage the 2 claws and remove the inner weatherstrip from the garnish. Parts Information Repair Procedure Clip POWER SLIDING DOOR INOPERATIVE – EL004-04 April 19, 2004 Page 3 of 7 2. Remove Side Trim Board Cover Rear. A. Remove the 2 screws. B. Using the taped screwdriver, disengage the 8 claws and remove the cover together with the window control switch. C. Remove the 2 screws and window control switch. 3. Remove Rear Door Trim Board Sub-assembly. A. Remove the screw. B. Using the taped screwdriver, disengage the 9 clips and remove the trim board. HINT: In order to prevent the door panel from being damaged, cover the areas with protective tape as indicated by the arrows in the illustration. 4. Remove Rail End Molding. A. Open the quarter glass. B. Using the taped screwdriver, disengage the clip and 2 claws, and remove the rail end molding. Repair Procedure (Continued) : Claw 1 2 3 4 5 5 4 3 2 1 Protective Tape Protective Tape : Clip : Clip : Claw POWER SLIDING DOOR INOPERATIVE – EL004-04 April 19, 2004 Page 4 of 7 5. Remove Center Bracket No. 2. A. Remove the 2 bolts and Center Bracket No. 2 together with the tensioner (color: white). B. Remove the tensioner from Center Bracket No. 2. 6. Remove Center Bracket No. 1. A. Remove the 2 bolts and Center Bracket No. 1 together with the tensioner (color: black). B. Remove the tensioner from Center Bracket No. 1. 7. Remove Slide Door Window Assembly LH. A. With Sunshade: Remove the sun shade hook. B. Remove the bolt and window frame. C. Remove the bolt. D. Loosen the nut. E. Push the rear lower window frame in the direction indicated by the arrow in the illustration

1984 TOYOTA SIENNA 2nd SEAT FLOOR LINER INSTALLATION MANUAL

download
TO INSTALL YOUR LINER, FIRST SLIDE THE 2ND ROW SEATS TOWARD THE BACK OF THE VEHICLE FAR ENOUGH TO ALLOW ROOM FOR THE LINER TO BE INSTALLED. WITH THE LINER IN PLACE, MOVE THE 2ND ROW SEATS FORWARD UNTIL THEY MATCH UP TO THE REAR EDGE OF THE LINER. YOUR SIENNA LINER IS DESIGNED TO WORK WITH THE MULTIPLE CONFIGURATIONS OF THE SIENNA VAN. AS IT IS BOXED, THE LINER WILL FIT 7- PASSENGER MODELS WITH THE FRONT ROW CONSOLE POSITIONED BETWEEN THE FRONT ROW OF SEATS. THE LINER CAN EASILY BE TRIMMED TO ALLOW THE CONSOLE TO BE REPOSTIONED INTO THE 2ND ROW AREA AS SHOWN IN THE DIAGRAM ABOVE (SEE AREA 1 AND PHOTOS ON BACK OF THIS PAGE). TO TRIM, SIMPLY USE THE MOLDED IN STEP IN THE PART AS A GUIDE AND REMOVE THE SECTION OF THE LINER AS SHOWN. A UTILITY KNIFE OR HEAVY SHEARS WORK WELL FOR TRIMMING. IF YOUR SIENNA IS AN 8-PASSENGER MODEL, YOU WILL NEED TO REMOVE THE “TONGUE” FROM THE REAR OF THE LINER (SEE AREA 2 ABOVE). THIS IS EASILY DONE USING THE MOLDED IN STEP IN THE PART AS THE TRIMMING GUIDE. ONCE AGAIN, A UTILITY KNIFE OR HEAVY SHEARS WORK WELL FOR TRIMMING.