Bomag BF 300 P Road Finisher Service Training 00892115

Description

• Model List:
  • BF 300 P Road Finisher

• 1. BF 300_P
• 1.1. BF 300_P
• 2.
• 2.1.
• 3. General
• 3.1. General
• 3.2. Introduction
• 3.3. General
• 3.4. General
• 3.5. Transport work with cranes and lifting tackle
• 3.6. Precautions and codes of conduct for welding work
• 3.7. Operation of highvoltage systems
• 3.8. Old oils
• 3.9. Hydraulics
• 3.10. Hot fuels
• 3.11. Synthetic rubber
• 3.12. Poisonous substances
• 3.13. Battery
• 3.14. Special safety regulations
• 3.15. The values specified in the table apply for screws
• 3.16. The values specified in the table apply for screws
• 3.17. The values specified in the table apply for screws
• 3.18. The values specified in the table apply for screws
• 3.19. The values specified in the table apply for screws
• 3.20. The values specified in the table apply for screws
• 3.21. The values specified in the table apply for screws
• 3.22. The values specified in the table apply for screws
• 3.23. The values specified in the table apply for screws
• 3.24. The values specified in the table apply for screws
• 3.25. The values specified in the table apply for screws
• 3.26. The values specified in the table apply for screws
• 3.27. The values specified in the table apply for screws
• 4. Technical data
• 4.1. Technical data
• 4.2.
• 4.3.
• 5. Maintenance
• 5.1. Maintenance
• 5.2. General notes on maintenance
• 5.3. Fuels and lubricants
• 5.4. Coolant
• 5.5. Mineral oil based hydraulic oil
• 5.6. Gear oil
• 5.7. Lubrication grease
• 6. EPlan wiring diagrams
• 6.1. EPlan wiring diagrams
• 7. Electrics
• 7.1. Electrics
• 7.2.
• 7.3.
• 7.4.
• 7.5.
• 7.6.
• 7.7.
• 7.8.
• 7.9.
• 7.10.
• 7.11.
• 7.12.
• 7.13. Fuse assignment
• 7.14. Fuse assignment
• 7.15. Component overview
• 7.16. View of operators stand
• 7.17. View of operators stand
• 7.18. View of operators stand
• 7.19.
• 7.20. Pressure gauge for relief pressure
• 7.21. Pressure gauge for relief pressure
• 7.22. Pressure gauge for relief pressure
• 7.23. Pressure gauge for relief pressure
• 8. Input codes
• 8.1. Input codes
• 8.2. Deactivating / activating the brake pedal switch
• 9. Replacement of components
• 9.1. Replacement of components
• 10. Engine
• 10.1. Engine
• 10.2. Check the coolant level
• 10.3. Check the coolant level
• 10.4. Check the coolant level
• 10.5. Check the coolant level
• 10.6. Check the coolant level
• 10.7. Check the antifreeze concentration and the condition of the coolant
• 10.8. Change the coolant
• 10.9. Checking radiator hoses and hose clamps
• 10.10. Clean the cooling fins on engine and hydraulic oil cooler
• 10.11. Checking the engine oil level
• 10.12. Changing engine oil and oil filter cartridge
• 10.13. Replace the fuel filter
• 10.14. Replace the fuel filter
• 10.15. Checking, cleaning the water separator
• 10.16. Changing the fuel filter, bleeding the fuel system
• 10.17. Check fuel lines and clamps
• 10.18. Check the fuel injection nozzles
• 10.19. Check the fuel injection timing
• 10.20. Check the fuel injection pump
• 10.21. Servicing the generator Vbelt
• 10.22. Air filter maintenance
• 10.23. Check the engine mounts
• 10.24. Engine conservation
• 10.25. Check, adjust the valve clearance
• 11. Material hopper, description
• 11.1. Material hopper, description
• 12. Vibrating screed, description
• 12.1. Vibrating screed, description
• 13. Travel drive, description
• 13.1. Travel drive, description
• 14. Cleaning kit, description
• 14.1. Cleaning kit, description
• 15. Hydraulics
• 15.1. Hydraulics
• 15.2. Variable displacement pumps, A10VG28/45/56 EP
• 15.3. Variable displacement pumps, A10VG28/45/56 EP
• 15.4. Variable displacement pumps, A10VG28/45/56 EP
• 15.5. Axial piston pumps, A10VO/VSO 18 to 100 DFR1
• 15.6. Axial piston pumps, A10VO/VSO 18 to 100 DFR1
• 15.7. Swash plate principle, pump
• 15.8. Gear pump WP09
• 15.9. Gear pump WP09
• 15.10. Vibration and tamper motor SNM2
• 15.11. Vibration and tamper motor SNM2
• 15.12. Component overview hydraulics
• 15.13. Check the hydraulic oil level
• 15.14. Check the hydraulic oil level
• 15.15. Check the hydraulic oil level
• 15.16. Check the hydraulic oil level
• 15.17. Check the hydraulic oil level
• 15.18. Check the hydraulic oil level
• 15.19. Changing hydraulic oil and filter
• 16. Tests and adjustments
• 16.1. Tests and adjustments
• 16.2. Checking and adjusting the vibration
• 16.3. Checking and adjusting the vibration
• 16.4. Checking/adjusting tamping
• 16.5. Checking/adjusting the scraper belts
• 16.6. Checking/adjusting the augers
• 16.7. Checking/adjusting the main screed
• 16.8. Checking/adjusting the screed levelling
• 16.9. Checking/adjusting the hopper wings
• 16.10. Checking/adjusting the mobile screed
• 17. Central lubrication system
• 17.1. Central lubrication system
• 18. Circuit diagrams
• 18.1. Circuit diagrams
• 18.2.
• 18.3.
• 18.4.
• 18.5.
• 18.6.
• 18.7.
• 18.8.
• 18.9.
• 19.
• 19.1.