Bomag BF 600 C-HSE, BF 600 C-HCE Road Finisher Service Manual 00892122

Description

• Model List:
  • BF 600 C-HSE Road Finisher
  • BF 600 C-HCE Road Finisher

• 1. BF 600 C HSE
• 1.1. BF 600 C HSE
• 2. General
• 2.1. General
• 2.2. Introduction
• 2.3. General
• 2.4. General
• 2.5. Transport work with cranes and lifting tackle
• 2.6. Precautions and codes of conduct for welding work
• 2.7. Operation of highvoltage systems
• 2.8. Old oils
• 2.9. Hydraulics
• 2.10. Hot fuels
• 2.11. Synthetic rubber
• 2.12. Poisonous substances
• 2.13. Battery
• 2.14. Special safety regulations
• 2.15. The values specified in the table apply for screws
• 2.16. The values specified in the table apply for screws
• 2.17. The values specified in the table apply for screws
• 2.18. The values specified in the table apply for screws
• 2.19. The values specified in the table apply for screws
• 2.20. The values specified in the table apply for screws
• 2.21. The values specified in the table apply for screws
• 2.22. The values specified in the table apply for screws
• 2.23. The values specified in the table apply for screws
• 2.24. The values specified in the table apply for screws
• 2.25. The values specified in the table apply for screws
• 2.26. The values specified in the table apply for screws
• 2.27. The values specified in the table apply for screws
• 2.28. The values specified in the table apply for screws
• 3. Technical data
• 3.1. Technical data
• 3.2.
• 3.3.
• 3.4.
• 3.5.
• 4. Maintenance
• 4.1. Maintenance
• 4.2. General notes on maintenance
• 4.3. Fuels and lubricants
• 4.4. Coolant
• 4.5. Mineral oil based hydraulic oil
• 4.6. Biodegradable hydraulic oil
• 4.7. Gear oil
• 4.8. Lubrication grease
• 5. Fundamental electrics
• 5.1. Fundamental electrics
• 5.2. Battery maintenance
• 5.3. Battery maintenance
• 5.4. Battery maintenance
• 5.5. Battery maintenance
• 5.6. Battery maintenance
• 5.7. Battery maintenance
• 5.8. Battery maintenance
• 5.9. Battery maintenance
• 5.10. Battery maintenance
• 5.11. Battery maintenance
• 5.12. Battery maintenance
• 5.13. Battery maintenance
• 5.14. Battery maintenance
• 5.15. Battery maintenance
• 5.16. Battery maintenance
• 5.17. Battery maintenance
• 5.18. Battery maintenance
• 5.19. Battery maintenance
• 5.20. Battery maintenance
• 5.21. Battery maintenance
• 5.22. Battery maintenance
• 5.23. Battery maintenance
• 5.24. Battery maintenance
• 5.25. Battery maintenance
• 5.26. Battery maintenance
• 5.27. Starting with jump wires
• 5.28.
• 5.29.
• 5.30. Replace heating elements
• 5.31. Replace heating elements
• 6. Engine electrics
• 6.1. Engine electrics
• 6.2. Diagnostics interface
• 6.3. Diagnostics interface
• 6.4. Diagnostics interface
• 6.5. Diagnostics interface
• 6.6. Diagnostics interface
• 6.7. Diagnostics interface
• 6.8. Diagnostics interface
• 6.9. Diagnostics interface
• 6.10. Diagnostics interface
• 6.11. Diagnostics interface
• 6.12. Diagnostics interface
• 6.13. Diagnostics interface
• 6.14. Diagnostics interface
• 6.15. Diagnostics interface
• 6.16. Diagnostics interface
• 6.17. Diagnostics interface
• 6.18. Diagnostics interface
• 7. Engine
• 7.1. Engine
• 7.2. Check the engine oil level
• 7.3. Check the engine oil level
• 7.4. Changing engine oil and oil filter cartridge
• 7.5. Replace the fuel filter cartridges.
• 7.6. Changing the fuel filter, bleeding the fuel system
• 7.7. Check, clean the water separator
• 7.8. Check the coolant level
• 7.9. Replacing the coolant
• 7.10. Air filter maintenance
• 7.11. Adjust the valve clearance
• 7.12. Adjusting the control piston play
• 7.13. Clean the cooling fins on engine and hydraulic oil cooler
• 7.14. Check the engine mounts
• 7.15. Replace the crank case ventilation valve
• 7.16. Electronic injector test EMR
• 7.17. Engine conservation
• 7.18. Checking the condition and tension of the screed heating generator Vbelt, tensioning and if necessary replacing the Vbelt
• 7.19. Check, tension, replace the V belt
• 8. Hydraulics
• 8.1. Hydraulics
• 8.2. Travel pumps
• 8.3. Travel pumps
• 8.4. Travel pumps
• 8.5. Charge pump
• 8.6. Charge pressure relief valve
• 8.7. Charge pressure filter
• 8.8. Multifunction valve
• 8.9. Flushing pressure relief valve
• 8.10. Travel gear
• 8.11. Test and adjustment points
• 8.12. Test and adjustment points
• 8.13. Test and adjustment points
• 8.14. Service block
• 8.15. Service block
• 8.16. Test and adjustment points
• 8.17. Levelling block
• 8.18. Test and adjustment points
• 8.19. External gear pumps
• 8.20. Scraper chain motors
• 8.21. Scraper chain motors
• 8.22. Orbital motor
• 8.23. Test and adjustment points
• 8.24. Conveyor screw motor
• 8.25. Outer gear motors nonreversible
• 8.26. Valve blocks
• 8.27. Valve blocks
• 8.28. Vibration and tamper motors
• 8.29. Outer gear motors nonreversible
• 8.30. Test and adjustment points
• 8.31. Test and adjustment points
• 8.32. Test and adjustment points
• 9. Tests and adjustments
• 9.1. Tests and adjustments
• 9.2. Checking and adjusting the vibration
• 9.3. Checking and adjusting the tamping process
• 9.4. Checking/adjusting the mobile screed
• 9.5. Checking/adjusting the hopper wings
• 9.6. Checking adjusting the time for screed levelling
• 10. Central lubrication system
• 10.1. Central lubrication system
• 11. Suppliers documentation
• 11.1. Suppliers documentation
• 12. Circuit diagrams
• 12.1. Circuit diagrams
• 13.
• 13.1.