Bomag BM 1000-30-2 to BM 1300-30-2-PB Cold Milling Machine Service Training 00891942

Description

• Model List:
  • BM 1000-30-2 Cold Milling Machine
  • BM 1200-30-2 Cold Milling Machine
  • BM 1300-30-2 Cold Milling Machine
  • BM 1000-30-2-PB Cold Milling Machine
  • BM 1200-30-2-PB Cold Milling Machine
  • BM 1300-30-2-PB Cold Milling Machine

• 1. BM 1000/302/1200/302/1300/302
• 1.1. BM 1000/302/1200/302/1300/302
• 2. General
• 2.1. General
• 2.2. Introduction
• 2.3. General
• 2.4. General
• 2.5. Transport work with cranes and lifting tackle
• 2.6. Precautions and codes of conduct for welding work
• 2.7. Operation of highvoltage systems
• 2.8. Old oils
• 2.9. Hydraulics
• 2.10. Hot fuels
• 2.11. Synthetic rubber
• 2.12. Poisonous substances
• 2.13. Battery
• 2.14. Special safety regulations
• 2.15. The values specified in the table apply for screws
• 2.16. The values specified in the table apply for screws
• 2.17. The values specified in the table apply for screws
• 2.18. The values specified in the table apply for screws
• 2.19. The values specified in the table apply for screws
• 2.20. The values specified in the table apply for screws
• 2.21. The values specified in the table apply for screws
• 2.22. The values specified in the table apply for screws
• 2.23. The values specified in the table apply for screws
• 2.24. The values specified in the table apply for screws
• 2.25. The values specified in the table apply for screws
• 2.26. The values specified in the table apply for screws
• 2.27. The values specified in the table apply for screws
• 3. Technical data
• 3.1. Technical data
• 3.2.
• 3.3.
• 4. Maintenance
• 4.1. Maintenance
• 4.2. Fuels and lubricants
• 4.3. Coolant
• 4.4. Mineral oil based hydraulic oil
• 4.5. Gear oil
• 4.6. Lubrication grease
• 5. Electrics
• 5.1. Electrics
• 5.2.
• 5.3.
• 5.4.
• 5.5.
• 5.6.
• 5.7.
• 5.8. View of operators stand
• 5.9. View of operators stand
• 5.10. B17S3, B17S4, B17S5 Control console travel system
• 5.11. Operating conditions for height regulation
• 5.12. Operating conditions for height regulation
• 5.13. Differential pressure switch for hydraulic oil
• 5.14. Engine speed sensor, C8
• 5.15. Pin assignment for control
• 6. Engine
• 6.1. Engine
• 6.2. Engine attachment parts
• 6.3. Engine attachment parts
• 6.4. Checking the cylinder head ground cable
• 6.5. Checking the cylinder head ground cable
• 6.6. Check the engine oil level
• 6.7. Change engine oil and oil filter cartridge
• 6.8. Check, clean the water separator
• 6.9. Change the fuel prefilter cartridge
• 6.10. Replace the fuel filter cartridge
• 6.11. Checking the combustion air filter
• 6.12. Service the combustion air filter
• 6.13. Check the coolant level
• 6.14. Checking the condition of the coolant hoses
• 6.15. Change the coolant
• 6.16. Clean the cooling fins on engine and hydraulic oil cooler
• 6.17. Checking, tensioning the V belt for the generator system
• 6.18. Cleaning the crankcase ventilation
• 6.19. Check the engine mounts
• 6.20. Checking the valve clearance
• 7. Milling drive, description
• 7.1. Milling drive, description
• 8. Milling unit, description
• 8.1. Milling unit, description
• 8.2. Milling unit
• 8.3. Milling unit
• 8.4. Milling drum
• 8.5. Milling housing
• 8.6. Holddown
• 8.7. Scraper
• 8.8. Side plate
• 9. Travel drive, description
• 9.1. Travel drive, description
• 10. Conveyor belt, description
• 10.1. Conveyor belt, description
• 10.2. Conveyor belts
• 10.3. Folding / unfolding the loading conveyor belt
• 11. Hydraulics
• 11.1. Hydraulics
• 11.2. Component overview hydraulics
• 11.3. Component overview hydraulics
• 11.4. Variable displacement pumps, A4VG28EP to A4VG180EP
• 11.5. Variable displacement pumps, A4VG28EP to A4VG180EP
• 11.6. Travel pump viewed on the machine
• 11.7. Travel pump viewed on the machine
• 11.8. Working pump viewed on the machine
• 11.9. Working pump viewed on the machine
• 11.10. Working pump viewed on the machine
• 11.11. Working pump viewed on the machine
• 11.12. Variable displacement pumps, A4VG28EP to A4VG180EP
• 11.13. Variable displacement pumps, A4VG28EP to A4VG180EP
• 11.14. Conveyor belt pump viewed on the machine
• 11.15. Conveyor belt pump viewed on the machine
• 11.16. Swash plate principle
• 11.17. Gear pump WP09
• 11.18. Gear pump WP09
• 11.19. Fan pump viewed on the machine
• 11.20. Fan pump viewed on the machine
• 11.21. Description of function
• 11.22. Description of function
• 11.23. Travel motor viewed on the machine
• 11.24. Travel motor viewed on the machine
• 11.25. Check the hydraulic oil level
• 11.26. Clean the cooling fins on engine and hydraulic oil cooler
• 11.27. Changing hydraulic oil and breather filter
• 11.28. Changing the hydraulic oil filter
• 12. Hydraulics travel circuit
• 12.1. Hydraulics travel circuit
• 12.2. Travel system
• 12.3. Travel system
• 12.4. Levelling
• 12.5. Levelling
• 12.6. Steering
• 12.7. Steering
• 13. Hydraulics milling operation
• 13.1. Hydraulics milling operation
• 13.2. Clutch viewed on the machine
• 13.3. Clutch viewed on the machine
• 13.4. Side plates
• 13.5. Side plates
• 13.6. Holddown
• 13.7. Scraper
• 14. Tests and adjustments
• 14.1. Tests and adjustments
• 14.2. Checking/adjusting the travel pump
• 14.3. Checking/adjusting the travel pump
• 15. Circuit diagrams
• 15.1. Circuit diagrams