Bomag BM 2200-75 Electric Training 00840141

Description

• Model List:
  • BM 2200-75

• 1. Table of contents
• 2. Training of electric system
• 2.1. Display
• 2.1.1. Measuring value screens
• 2.1.2. Service access
• 2.1.3. Teaching and learning procedures
• 2.1.4. Configurations
• 2.1.5. Actuator test
• 2.1.6. Showing/deleting the fault log
• 2.1.7. Warnings
• 2.1.8. Update of display software
• 2.1.9. Starting up the display without machine identification
• 2.1.10. Running system functions
• 2.1.10.1. Belt for milling drum drive
• 2.1.10.2. Extraction system
• 2.1.10.3. Height limitation lifting columns
• 2.1.10.4. Pause function setting
• 2.1.10.5. Standby function setting
• 2.2. Procedures for commissioning the machine
• 2.2.1. Closing the parking brake
• 2.2.2. Activating the starter
• 2.2.3. Deactivating monitoring of the belt drive cover
• 2.2.4. Resetting levelling
• 2.2.5. Input codes
• 2.3. Teaching and learning procedures
• 2.3.1. Lifting column adjustment learning function
• 2.3.2. Steering setting zero position
• 2.3.3. Steering learning function
• 2.3.4. Travel system learning
• 2.3.5. Adjusting levelling
• 2.3.6. Zeroing the lifting column heights
• 2.4. Configurations
• 2.4.1. Activating/deactivating configurations
• 2.5. Replacement of components
• 2.5.1. Introduction
• 2.5.2. Replacement of the ESX control
• 2.5.3. Replacement of engine components
• 2.5.4. Replacing components without an adjustment procedure
• 2.6. CAN BUS overview
• 2.7. Levelling control commissioning
• 2.7.1. Preliminary remarks and safety notes
• 2.7.2. Control unit for levelling system
• 2.7.2.1. Buttons and displays
• 2.7.2.2. Display
• 2.7.2.3. Navigating through the menus
• 2.7.3. Preparations for levelling
• 2.7.3.1. Setting the screen contrast
• 2.7.3.2. Sensor selection for control circuits left and right
• 2.7.3.3. Zero balancing
• 2.7.4. Working with levelling system
• 2.7.4.1. Setting the nominal value
• 2.7.4.2. Adjusting actual value equals nominal value
• 2.7.4.3. Lifting up and cutting in
• 2.7.5. Adapting the control speed
• 2.7.6. Adjusting the control window
• 2.7.6.1. Adjusting the control window equally for all distance sensors
• 2.7.6.2. Adjusting the rope sensor control window
• 2.7.6.3. Adjusting the crossslope sensor control window
• 2.7.7. Changing measurement units
• 2.7.7.1. Changing rope sensor measurement units
• 2.7.7.2. Changing crossslope sensor measurement units
• 2.7.8. Changing the deadband
• 2.7.9. Changing the work mode
• 2.7.10. Configuration menu
• 2.7.10.1. Hydraulic calibration
• 2.7.10.1.1. Calibrating MIN pulse
• 2.7.10.1.2. Calibrating MAX pulse
• 2.7.10.2. Editing the information lines for the activation message
• 2.7.11. Inspection and troubleshooting