Bomag BW 161 ADO-5, BW 161 AC-5, BW 161 AD-5 Tandem Vibratory Roller Service Manual 00892549

Description

• Model List:
  • BW 161 ADO-5 Tandem Vibratory Roller
  • BW 161 AC-5 Tandem Vibratory Roller
  • BW 161 AD-5 Tandem Vibratory Roller

• 1. Table of contents
• 2. General
• 2.1. Introduction
• 2.2. Concerning your safety
• 2.3. Maintenance and repair
• 3. Fuels and lubricants
• 3.1. Fuels and lubricants
• 3.2. List of fuels and lubricants, BW 161 AD
• 3.3. List of fuels and lubricants, BW 161 AC
• 3.4. List of fuels and lubricants, BW 161 ADO
• 4. Technical data
• 4.1. Technical data BW 161 AD5
• 4.2. Technical data BW 161 AC5
• 4.3. Technical data BW 161 ADO5
• 4.4. Additional technical data
• 4.5. Terms and basis of calculation
• 5. Overview of machine
• 5.1. Electric systems
• 5.2. Diesel engine
• 5.3. Hydraulic system
• 5.4. Water spraying system
• 5.5. Air conditioning
• 5.6. Drum
• 6. Electric systems
• 6.1. Overview of electric system
• 6.2. Table of fuels and lubricants
• 6.3. Wiring
• 6.4. CAN BUS overview
• 6.5. Power board
• 6.6. Control console cabin
• 6.7. Fuse assignment
• 6.8. Operators stand
• 6.9. Starting the engine with jump leads
• 6.10. Electric steering wheel, A45
• 6.11. Hydraulic cylinder with path measuring system
• 6.12. Asphalt temperature sensor, B106
• 6.13. Acceleration transducer, B84 B85
• 6.14. Switching on the pressurized spraying system
• 6.15. Switching the emulsion spraying system on
• 6.16. Data collector, A80
• 6.17. Differential pressure switch for hydraulic oil filter, B21
• 6.18. Air filter vacuum switch, B03
• 6.19. Sensor, water in fuel, B124
• 6.20. Float switch coolant tank, B55
• 6.21. Charge control light
• 6.22. Electric module, A108
• 6.23. Generator
• 6.24. Starter
• 6.25. Telemecanique switch
• 6.26. Deutsch plug, series DT and DTM
• 6.27. Inspection and maintenance work
• 7. Diesel engine
• 7.1. Overview of diesel engine
• 7.2. Features
• 7.3. Cooling system
• 7.4. Intake air heating
• 7.5. Fuel supply
• 7.6. CommonRail system
• 7.7. Exhaust system
• 7.8. Regeneration of exhaust gas aftertreatment system
• 7.9. Removing and installing the thermostat
• 7.10. Checking the thermostat in disassembled state
• 7.11. Inspection and maintenance work
• 8. Hydraulic system
• 8.1. Overview of hydraulics
• 8.2. Open and closed hydraulic circuit
• 8.3. Hydraulic units
• 8.4. Charge circuit and fan circuit
• 8.5. Travel circuit
• 8.6. Vibration circuit
• 8.7. Steering and crabwalk
• 8.8. Steering and crabwalk using slidable swivel seat
• 8.9. Edge cutter
• 8.10. Chip spreader
• 8.11. Tests and adjustments
• 8.12. Flushing and bleeding
• 8.13. Inspection and maintenance work
• 9. Water spraying system
• 9.1. Overview of water spraying system
• 9.2. Inspection and maintenance work
• 10. Air conditioning
• 10.1. Overview of air conditioning system
• 10.2. Physical principles
• 10.3. Refrigerant R134a
• 10.4. Compressor oil / refrigeration oil
• 10.5. Working principle of the air conditioning system
• 10.6. Monitoring devices
• 10.7. Description of components
• 10.8. Compressor
• 10.9. Emptying in case of repair
• 10.10. Drying and evacuation
• 10.11. Filling instructions
• 10.12. Steam table for R134a
• 10.13. Inspection and maintenance work
• 11. Drum
• 11.1. AD drum
• 11.2. ADO drum
• 11.3. Edge cutter
• 11.4. Inspection and maintenance work
• 12. Chip spreader
• 12.1. Mounting / removing the precision spreader
• 12.2. Inspection and maintenance work
• 13. Cabin assembly
• 13.1. Preparations
• 13.2. Cabin assembly
• 13.3. Final function tests and checks
• 14. Troubleshooting
• 14.1. Preliminary remarks
• 14.2. Emergency procedures
• 14.3. Troubleshooting, electrical systems
• 14.4. Trouble shooting, diesel engine
• 14.5. Trouble shooting, hydraulics
• 14.6. Trouble shooting, air conditioning system
• 15. Disposal
• 15.1. Final shutdown of machine
• 16. Special tools
• 16.1. Special tools, electrics
• 16.2. Special tools, hydraulic system
• 16.3. Special tools for ADO drum
• 16.4. List of special tools
• 17. Index
• 18. Appendix
• 18.1. A Circuit diagrams