Bomag BW 226 DH-4, BVC Single Drum Roller Service Manual 00891420

Description

• Model List:
  • BW 226 DH-4 Single Drum Roller
  • BVC Single Drum Roller

• 1. BW 226 DH4
• 2. Single drum roller
• 3. Introduction
• 4. Safety regulations
• 5. General repair instructions
• 6. Tightening torques
• 7. Technical data
• 8. General notes on maintenance
• 9. Fuels and lubricants
• 10. Table of fuels and lubricants
• 11. Runningin instructions
• 12. Maintenance chart
• 13. Connection overview travel/vibration pump
• 14. Special tools, tests and adjustments
• 15. Activate service mode
• 16. Driving against the closed brake
• 17. Turn the steering against an end stop.
• 18. Pressure tests in the travel circuit
• 19. Checking / adjusting the neutral positions of the travel pump
• 20. Pressure measurements in the vibration circuit
• 21. Check the leakage rate of the vibration motor
• 22. Pressure test in steering circuit
• 23. Special tools for flushing
• 24. Flushing general
• 25. Flushing schematic travel circuit (distribution travel pump)
• 26. Flushing the travel circuit (travel pump distribution)
• 27. Flushing schematic travel circuit (distribution axle motor)
• 28. Flushing the travel circuit (axle motor distribution)
• 29. Flushing schematic for vibration drive
• 30. Flushing the vibration circuit
• 31. Bleeding the travel circuit
• 32. Bleeding the vibration circuit
• 33. Understanding circuit diagrams
• 34. Terminal designations in wiring diagram
• 35. Circuit symbols in the circuit diagram
• 36. Battery ground and analog ground
• 37. Current and voltage
• 38. Resistance
• 39. Series / parallel connection
• 40. Ohms law
• 41. Electrical energy
• 42. Formula diagram
• 43. Metrology
• 44. Diodes, relays, fuses
• 45. Batteries
• 46. Generator
• 47. Electric starter
• 48. Telemecanique switch
• 49. Inductive proximity switches
• 50. Angle sensors
• 51. Plug connectors
• 52. Magnetic coil plug
• 53. Deutsch plug, series DT and DTM
• 54. Plugs and terminals in spring clamping technology
• 55. Electronic control units
• 56. Special tools, electrics
• 57. Diagnostics concept
• 58. Checking the voltage supply for the control unit
• 59. Machine related electrics
• 60. Electrics MESX
• 61. Heating/air conditioning control
• 62. Service Training Machine
• 63. Service Training BVC
• 64. Diesel engine
• 65. Engine description TCD 2012
• 66. Lubrication oil circuit TCD 2012 / 2013
• 67. Coolant circuit TCD 2012 / 2013
• 68. Fuel system TCD 2012 / 2013
• 69. Deutz Common Rail (DCR) injection system for TCD 2012 / 2013
• 70. Sensors TCD 2012 / 2013
• 71. Engine control EDC16 with EMR 3 for TCD 2012 / 2013
• 72. Exhaust gas recirculation TCD 2012 / 2013
• 73. Fault code monitoring with display TCD 2012 / 2013
• 74. Fault code display TCD 2012 / 2013
• 75. EMR3 List of fault codes
• 76. SerDia ServiceSoftware TCD 2012 / 2013
• 77. General trouble shooting chart TCD 2012 / 2013
• 78. Check the engine oil level
• 79. Changing engine oil and oil filter cartridges
• 80. Change the fuel prefilter cartridge
• 81. Change the fuel filter cartridge
• 82. Check, clean the water separator
• 83. Check the coolant level
• 84. Change the coolant
• 85. Service the combustion air filter
• 86. Checking the dust separator on the oil bath air filter
• 87. Cleaning the oil bath air filter
• 88. Adjusting the valve clearance
• 89. Checking / replacing the ribbed Vbelt
• 90. Check the engine mounts
• 91. Replacing the crank case pressure ventilation valve
• 92. Engine conservation
• 93. Checking the engine pillow blocks
• 94. Special tools, Deutz engines with EMR control
• 95. Special tools, Deutz engine (TCD 2012 2V)
• 96. Physical basics
• 97. Refrigerant R134a
• 98. Compressor oil / refrigeration oil
• 99. Working principle of the air conditioning system
• 100. Monitoring devices
• 101. Description of components
• 102. Checking the compressor oil level
• 103. Checking the magnetic clutch
• 104. Inspection and maintenance work
• 105. Checking, replacing the refrigerant compressor Vbelt
• 106. Service the air conditioning
• 107. Drying and evacuation
• 108. Emptying in case of repair
• 109. Leak test
• 110. Filling instructions
• 111. Trouble shooting in refrigerant circuit, basic principles
• 112. Trouble shooting, refrigerant circuit diagram
• 113. Trouble shooting procedure
• 114. Steam table for R134a
• 115. Assembly of window panes
• 116. Special tools
• 117. Auxiliary materials
• 118. Removing and installing the window pane
• 119. Special tools, drum BW 213/226 DH4 BVC and Variocontrol
• 120. Repair overview for drum