Clark Fork Lift CER10-13, CER14-15-18, CER20-25 Operation and Maintenance Manual OM-694

Description

• Model List:
  • Fork Lift CER10-13
  • Fork Lift CER14-15-18
  • Fork Lift CER20-25

• 1. CONTENTS
• 1.1. PREFACE
• 1.2. SAFETY
• 1.3. GENERAL
• 1.3.1. DESIGNATED WORKS
• 1.3.2. CHARACTERISTICS OF THE MACHINE
• 1.4. DRIVING LICENSE
• 1.5. NAME PLATE
• 1.5.1. LOCATION OF NAME PLATES
• 1.5.2. LOCATION OF MARKING PLATE
• 1.6. BASIC PRECAUTIONS
• 1.7. SAFETY TRAVELING
• 1.8. HOW TO USE THE BATTERY AND CAUTIONS FOR CHARGING
• 1.9. CAUTIONS WHEN OPERATING THE MACHINE
• 1.10. TRANSPOTATION
• 1.10.1. REACH CYLINDER PIN
• 1.10.2. MAIN LIFT TILT RETURN HOSE
• 1.10.3. FORK LOAD BACKREST
• 1.11. ATTACHED POSITION OF SAFETY DECALS
• 1.11.1. ATTACHED POSITION OF SAFETY DECALS
• 1.11.2. CONTENTS OF SAFETY DECALS
• 2. OPERATION
• 2.1. GENERAL LOCATIONS
• 2.2. DRIVING AND OPERATING
• 2.2.1. LCD DISPLAY PANEL AND CONTROLLER
• 2.2.2. OPERATING
• 2.3. BATTERY DHARGING
• 2.3.1. NORMAL CHARGING
• 2.3.2. EQUAL CHARGING
• 2.3.3. SUPPLEMENTARY CHARGING
• 2.3.4. CHARGING FOR LONG TERM STORAGE
• 2.3.5. CHARGING METHOD
• 2.4. STATIONARY BATTERY
• 2.4.1. CHARGING METHOD (NORMAL CHARGING)
• 2.5. BATTERY REPLACEMENT
• 2.6. LEVEL OF BATTERY ELECTROLYTE AND READING GRAVIMETER
• 2.6.1. LEVEL OF BATTERY ELECTROLYTE
• 2.6.2. HOW TO READ THE GRAVIMETER
• 2.6.3. SPECIFIC GRAVITY OF ELECTROLYTE AND CONVERSION TABLE OF TEMPERATURE COMPENSATION
• 2.7. SOUND INFORMATION
• 2.7.1. SOUND LEVEL
• 2.8. CHECK BEFORE WORKING
• 2.8.1. CHECKING POINTS
• 2.8.2. CHECKING METHODS BEFORE STARTING OPERATION
• 2.9. LOAD AND STABILITY OF MACHINE
• 2.9.1. STANDARD LOAD CENTER AND LOAD CURVE
• 2.9.2. STABILITY OF MACHINE
• 2.10. OPERATING AND UNLOADING
• 2.10.1. PREPARATION FOR STARTING
• 2.10.2. OPERATING
• 3. INSPECTIONMAINTENANCE
• 3.1. INSPECTION AND MAINTENANCE
• 3.1.1. GENERAL CAUTIONS FOR INSPECTION AND MAINTENANCE
• 3.1.2. INSPECTION EVERY WEEK (50HR)
• 3.1.3. MEASURING SPECIFIC GRAVITY
• 3.1.4. CLEANING BATTERY
• 3.1.5. INSPECTION EVERY MONTH (200HR)
• 3.1.6. INSPECTION EVERY 2 MONTHS (400 HR)
• 3.1.7. INSPECTON EVERY 3 MONTHS (600 HR)
• 3.1.8. INSPECTION OF CARBON BRUSH
• 3.2. LUBRICATION CHART
• 3.2.1. LUBRICATING POINT
• 3.2.2. SPECIFIED LUBRICATION CHART
• 3.3. GUIDE TO REPLACE AND REPAIR PARTS
• 3.3.1. HOW TO REPLACE THE CONTACTOR
• 3.3.2. HOW TO ADJUST THE BRAKE
• 3.4. REFRIGERATING SPECIFIED VEHICLE
• 3.4.1. COUNTERMEASURE FOR ANTICORROSION
• 3.4.2. COUNTERMEASURE FOR LOW TEMPERATURE
• 3.4.3. USAGE OF NO SLIP TIRE
• 4. SPECIFICATIONS
• 4.1. SPECIFICATIONS
• 4.1.1. DIMENSIONS
• 4.1.2. TRUCK SPECIFICATIONS
• 4.1.3. BATTERY SPECIFICATIONS
• 4.1.4. TIGHTENING TORQUE OF EACH PART