Linde 1151-01 – T16, T16P, T20, T20P Production site Xiamen Operating Instructions SN 07.11 and up

Description

• Model List:
  • T16
  • T16P
  • T20
  • T20P

• 1. series Electric Pallet TruckModel T20
• 1.1. Table of content
• 1.2. Introduction
• 1.2.1. Scope
• 1.2.2. Obligations of the Equipment Owner
• 1.2.3. Operator Responsibilities
• 1.2.4. Proper use
• 1.2.5. Hazard messages
• 1.3. Safety
• 1.3.1. Before Operation
• 1.3.2. Operator daily checklist
• 1.3.3. Operating Position
• 1.3.4. Travel
• 1.3.5. Inclines, Ramps, Docks, Elevators
• 1.3.6. Parking
• 1.3.7. Battery Safety
• 1.3.8. Safety During Maintenance
• 1.3.8.1. Personnel Qualifications
• 1.3.8.2. Hazardous Substances
• 1.3.9. Operator Warning Decals
• 1.3.9.1. Data plate
• 1.3.9.2. No riding decal
• 1.3.9.3. Trained operator warning decal
• 1.3.9.4. Test or service warning decal
• 1.3.9.5. Crushed fingers warning decal
• 1.3.9.6. No step warning decal
• 1.3.9.7. Voltage decal
• 1.4. Overview
• 1.4.1. Technical Description
• 1.4.2. Truck Components
• 1.4.3. Controls
• 1.4.4. Indicator Unit
• 1.4.5. Decal and Data Plate Location
• 1.4.6. Data Plate
• 1.4.7. Definition of directions
• 1.4.8. Options
• 1.5. Operation
• 1.5.1. Unloading and Preparing a New Truck for Operation
• 1.5.2. Turning the Truck On and Off
• 1.5.3. Keyless Access (Optional equipment)
• 1.5.4. Keyless Access Summary
• 1.5.5. Driving
• 1.5.6. Steering
• 1.5.7. Horn
• 1.5.8. Braking
• 1.5.9. Emergency Stop Handle
• 1.5.10. Raising and Lowering the Forks
• 1.5.11. Connecting and Disconnecting the Battery
• 1.5.12. Changing the Battery
• 1.5.13. Connecting the Battery to an External Charger
• 1.5.14. Hoisting the Truck
• 1.5.15. Towing the Truck
• 1.6. Maintenance
• 1.6.1. Personnel Qualifications
• 1.6.2. Cleaning the Truck
• 1.6.3. Daily Inspection
• 1.6.3.1. Daily Inspection Overview
• 1.6.4. Scheduled Maintenance
• 1.6.4.1. General Maintenance Information
• 1.6.4.2. Maintenance at 1000 Hours
• 1.6.4.3. Maintenance at 2000 Hours
• 1.6.4.4. Maintenance at 5000 Hours
• 1.6.4.5. Maintenance at 10,000 Hours
• 1.6.4.6. Scheduled Maintenance Summary
• 1.6.5. Fluids and Lubricants
• 1.6.5.1. Fluid and Lubricant Specifications
• 1.6.5.2. Capacities
• 1.6.6. Troubleshooting
• 1.6.6.1. Removing Chassis Covers
• 1.6.6.2. Fuses
• 1.6.6.3. Diagnostic Connector
• 1.7. Technical Data
• 1.7.1. Specifications
• 2. Electric Pallet Forklift TruckT16, T20Zapi controller
• 2.1. Table of content
• 2.2. Introduction
• 2.2.1. Legal requirements for marketing
• 2.2.2. Introduction
• 2.2.3. Intended use
• 2.2.4. Improper use
• 2.2.5. Additional information
• 2.2.6. Description of use and climatic conditions
• 2.2.7. Symbols used
• 2.2.8. Electric Pallet Truck 1151
• 2.3. Safety
• 2.3.1. Safety guidelines
• 2.3.2. Residual risks
• 2.3.3. Stability
• 2.3.4. EMC Electromagnetic compatibility
• 2.3.5. Handling consumables
• 2.3.6. Regulations
• 2.3.7. Competent person
• 2.4. General layout
• 2.4.1. Labels
• 2.4.2. Identification plates
• 2.4.3. T16 T20 Model General View
• 2.4.4. control unit
• 2.4.5. Battery Charging Indicator
• 2.4.6. Digicode option (LFM Go)
• 2.4.7. LFM Connect option
• 2.5.1. Settings
• 2.5.2. Checks before first commissioning
• 2.5.3. Preshift checks before starting work
• 2.5.4. Operating Instructions
• 2.5.5. Driving 1151
• 2.5.6. Using the truck on ramps
• 2.5.7. Creep Speed Function
• 2.5.8. Braking, lifting, lowering, horn
• 2.5.9. Working with loads
• 2.5.10. Lifting and towing
• 2.5.11. Cold store usage (optional)
• 2.6. Maintenance
• 2.6.1. Inspection and maintenance work tables
• 2.6.2. hour maintenance plan
• 2.6.3. hour maintenance plan
• 2.6.4. hour maintenance plan
• 2.6.5. Technical inspection and maintenance characteristics
• 2.6.6. Recommended lubricants
• 2.6.7. Preshift checks
• 2.6.8. Checking the brakes
• 2.6.9. Testing the safety devices
• 2.6.10. Checking the battery charging status
• 2.6.11. Connecting.disconnecting the battery plug connector
• 2.6.12. Opening the battery cover
• 2.6.13. Charging the battery with the builtin charger
• 2.6.14. Battery charging with an external charger
• 2.6.15. Essential maintenance
• 2.6.15.1. Cleaning the Pallet Truck
• 2.6.15.2. Cleaning the battery and its compartment
• 2.6.15.3. Accessing the electrical control compartment
• 2.6.15.4. Checking the condition of cables, terminals and the battery connector
• 2.6.15.5. Vertical change batteriesremoval.replacement
• 2.6.15.6. Lateral change batterychanging the battery using a trolley
• 2.6.15.7. Lateral change batterychanging the battery using a mobile support
• 2.6.16. hour maintenance plan
• 2.6.16.1. Checking the brake air gap
• 2.6.16.2. Adjusting the height of the stabilisers
• 2.6.16.3. Oil level check
• 2.6.16.4. Battery maintenance
• 2.6.16.5. Checking the wear on collars and hinge pins
• 2.6.16.6. Greasing the rings and articulations (greased option)
• 2.6.17. hour maintenance plan
• 2.6.17.1. Hydraulic circuit, draining the circuit
• 2.6.18. hour maintenance plan
• 2.6.18.1. Servicing the reducer
• 2.7. Datasheet
• 2.7.1. T16 . T20 Datasheet
• 2.7.2. Technical datasheet T16 . T20
• 3. Electric pallet truck1151_T16, 1151_T16P, 1151_T20, 1151_T20P
• 3.1. Table of content
• 3.2. Introduction
• 3.2.1. Introduction
• 3.2.2. Impermissible use
• 3.2.3. Description of use and climatic conditions
• 3.2.4. Symbols used
• 3.2.5. Legal requirements for marketing
• 3.2.6. Electric pallet trucks 1151
• 3.3. Safety
• 3.3.1. Residual risks
• 3.3.2. Stability
• 3.3.3. Safety regulations
• 3.3.4. Use of lubricants
• 3.3.5. Periodic general checks on trucks
• 3.4. General views
• 3.4.1. Labels
• 3.4.2. Identification plates
• 3.4.3. General view T16 T20 type 1151
• 3.4.4. General view T16P T20P type 1151
• 3.4.5. Controls for 1151
• 3.4.6. Battery charge indicator
• 3.4.7. Digicode option (LFM Go)
• 3.4.8. LFM AccessLFM Basic option
• 3.5.1. Setup
• 3.5.2. Checks before first commissioning
• 3.5.3. Preshift checks before starting work
• 3.5.4. Adjusting the onboard charger
• 3.5.5. Operating instructions for 1151
• 3.5.6. Driving the 1151
• 3.5.7. Use of the truck on a slope
• 3.5.8. Braking
• 3.5.9. Designation
• 3.6. Maintenance
• 3.6.1. General information
• 3.6.2. Daily checks before starting work
• 3.6.2.1. Checking the direction of travel controls
• 3.6.2.2. Checking the lifting.lowering controls
• 3.6.2.3. Checking the battery charging status
• 3.6.2.4. Battery charging using an external charger
• 3.6.3. Maintenance plan as required
• 3.6.3.1. Cleaning the battery and its compartment
• 3.6.3.2. Access to the technical compartment
• 3.6.3.3. Accessing the reducer and the brake
• 3.6.3.4. Checking the fuses
• 3.6.3.5. Opening the battery cover
• 3.6.3.6. Disconnecting.connecting the battery connector
• 3.6.4. Inspection and maintenance overview
• 3.6.5. Gearbox
• 3.6.6. Steering . braking . wheels
• 3.6.6.1. Adjusting the height of the stabilisers
• 3.6.7. Electrical equipment
• 3.6.7.1. Battery maintenance
• 3.6.7.2. Checking the onboard charger
• 3.6.8. Hydraulic circuits
• 3.6.8.1. Oil level check
• 3.6.8.2. Hydraulic circuit, draining the circuit
• 3.6.9. Lifting system
• 3.6.9.1. Checking the wear on collars and hinge pins
• 3.6.9.2. Greasing the rings and articulations (greased option)
• 3.7. Datasheet
• 3.7.1. Datasheet T16 . T20
• 3.7.2. Datasheet T16P . T20P
• 3.7.3. Noise emission values
• 4. Leadacid battery charger 24V
• 5. Leadacid battery charger 24V . 48V
• 6. Leadacid battery charger 24V . 48V . 80V