Linde 1167-02 – ML10, ML12, MM10, MM12, MM12i Production site Xiamen Operating Instructions SN CT1167H20001 and up

Description

• Model List:
  • ML10
  • ML12
  • MM10
  • MM12
  • MM12i

• 1. Electric Pallet StackerML10 . MM10 . MM10i
• 1.1. Table of content
• 1.2. Introduction
• 1.2.1. Introduction
• 1.2.2. Declaration that reflects the content of the declaration of conformity
• 1.2.3. Conformity marking
• 1.2.4. General information
• 1.2.5. Intended use
• 1.2.6. Improper use
• 1.2.7. Additional information
• 1.2.8. Description of use and climatic conditions
• 1.2.9. Symbols used
• 1.2.10. Series
• 1.3. Safety
• 1.3.1. Safety guidelines
• 1.3.2. Residual risks
• 1.3.3. Stability
• 1.3.4. Handling consumables
• 1.3.5. EMC Electromagnetic compatibility
• 1.3.6. Regulations
• 1.3.7. Competent person
• 1.4. Views
• 1.4.1. Drive directions
• 1.4.2. Load label
• 1.4.3. Nameplate
• 1.5. Operation
• 1.5.1. Intended use of the trucks
• 1.5.2. First use
• 1.5.3. Daily checks before use
• 1.5.4. Checking the working environment
• 1.5.5. General information on batteries
• 1.5.6. Drive operations
• 1.5.6.1. Description
• 1.5.6.2. Starting
• 1.5.6.3. Forward travel.reverse travel
• 1.5.6.4. Brake
• 1.5.6.5. Safety reverser
• 1.5.6.6. Steering
• 1.5.6.7. Using the truck on a slope
• 1.5.7. Hydraulic operations
• 1.5.7.1. Working with loads
• 1.5.7.2. Emergency lowering
• 1.5.8. Before leaving the equipment
• 1.5.9. Putting the equipment back into operation
• 1.5.10. Slinging
• 1.5.11. Transporting the truck
• 1.6. Maintenance
• 1.6.1. General maintenance information
• 1.6.1.1. General
• 1.6.1.2. Daily inspection
• 1.6.1.3. Servicing and maintenance personnel training and qualification
• 1.6.1.4. Battery maintenance staff
• 1.6.1.5. Maintenance operations that do not require special training
• 1.6.1.6. Technical inspection and maintenance data
• 1.6.2. Service plan
• 1.6.3. Maintenance work
• 1.6.3.1. Changing the battery
• 1.6.3.2. Lubrication point
• 1.6.3.3. Check the hydraulic oil level
• 1.6.3.4. Topping up the gear oil
• 1.6.3.5. Checking the fuses
• 1.6.4. Tyre operation
• 1.6.4.1. Drive Wheel
• 1.6.4.2. Load Wheels Removal and Installation
• 1.6.4.3. Caster Removal and Installation
• 1.6.5. Malfunction analysis
• 1.7. Technical data
• 1.7.1. Ecodesign requirements for electric motors and variable speed drives
• 1.8. Schematic diagrams
• 1.8.1. Harness Diagram
• 1.8.2. Hydraulic Diagram
• 1.8.3. Brake Principle